DuPont Protection Solutions

Transcription

1 DuPont Protection Solutions Technical Data Package DuPont Tychem FR (Reflector ) RF600T Compliant with Base Requirements and Chemical Flash Fire Protection Option and Liquefied Gas Protection Option Requirements of NFPA 1991, 2016 Edition Consult the DuPont Tychem Garment User Manual for Instructions on use This information packet may not be removed except by the end user K (5/2017)

2 Technical Data Package Technical Data Package Tychem FR (Reflector ) RF600T Compliant with Base Requirements and Chemical Flash Fire Protection Option and Liquefied Gas Protection Option Requirements of NFPA 1991, 2016 Edition Consult the DuPont Tychem Garment User Manual for Instructions on use Front Entry Style RF600T Accessories and certified pass thru options are listed in an attached document, DuPont Tychem Accessories List. NFPA 1991 Compliant Tychem FR (Reflector ) Ensembles are available in the following sizes: SM, MD, LG, XL, 2X, 3X, and 4X. The sizing chart for these garments is provided on the next page. NFPA 1991 Compliant Tychem FR (Reflector ) Ensembles are made from a proprietary aluminized fabric made using a DuPont Nomex and Kevlar aramid fiber blend fabric laminated to a multi-layer chemical barrier film. The chemical garment and visor seams are sewn using thread made of Kevlar or Nomex aramid fiber. The garment and visor seams are sealed inside and outside with hot-air welded chemical barrier tape. The visor material in the NFPA 1991 Compliant Tychem FR (Reflector ) ensemble consists of an outer layer of 40 mil PVC, a second layer of 5 mil Teflon FEP and a third inner layer of 40 mil PVC. There are no detachable or replaceable visor components. The glove configuration consists of: Outer Glove: Kevlar Knit Glove - Made of DuPont Kevlar Yarn Middle Glove: Guardian #IN 35 Neoprene Inner Glove: North SSG-Silver Shield /4H These gloves are unlined and have no surface treatments. The outer glove is provided in size 10, the middle glove in size 10 and the inner glove in size 11. The inner and middle gloves are connected to the sleeve of the chemical barrier garment with a rigid plastic ring and metal ring clamp. The seal is accomplished by mechanical compression of the garment and glove materials. The outer glove is not physically attached to the chemical suit; it is to be worn over the middle glove. Chemical barrier socks and boot cover flaps are attached to the garment and are made from suit material. The socks provide barrier protection for the wearer s feet. The ensembles are certified with Onguard HazMax 87012, Tingley HazProof (orange) and Tingley HazProof (black) boots that are to be worn over the socks and under the boot flaps. The boots are not physically attached to the garment. These boots have steel toes and ladder shanks and provide physical protection. There are no surface treatments applied to the boots. The Onguard HazMax boots are available in sizes 6 to 15. The Tingley HazProof boots are available in sizes 7 to 13. NOTE: The boots are not provided with the ensemble and must be purchased separately. Page 2 of 14

3 The 48 inch long, vapor-protective closure has alloy teeth. The slider components are aluminum-bronze. The zipper pull is an aluminum-bronze ring with a PVC pull extension. The closure is mounted on a PVC coated polyester fabric base tape that is sewn to inside of the chemical barrier garment and sealed with air welded tape. The closures are covered by two flaps made of primary garment material. The flaps are fastened with hook-and-loop closures. The closure has not been tested for permeation resistance. The two exhaust valves are manufactured by Pirelli. The valve is manufactured with an impact resistant plastic body and a removable splash shield. The diaphragm is made of molded rubber. The valves are inserted through the chemical suit material and secured with a threaded inner ring, sealed with mechanical compression. The valve assemblies are covered with a flap of primary suit material to reduce direct splash on the exhaust valve assembly. For information on purchasing replacement exhaust valve diaphragms, please call DuPont Customer Service: United States Instructions for replacing the exhaust valve diaphragm can be found in the DuPont Technical Data Package Garment Sizing Tychem Garment User s Manual for Universal Pressure Test Kit. This ensemble will accommodate a Class G cap compliant with ANSI Z89.1 worn inside the suit. Tychem garments may be used for 5 years from date of manufacture as long as all of the following conditions are met: 1. The garment has been stored properly (see section on Storage Conditions) 2. The garment has not been damaged, altered, or contaminated 3. The garment passes a full visual inspection (view garment inspection instructions). Shelf life of Tychem RF 600T garments is based on testing naturally aged garments. Following SCBA were used for certification of the garment. MSA Dual Purpose Thru w/ Hansen Fitting Model MSA Quick Fill Thru w/ Schrader Fitting Model Draeger Thru w/ Hansen Fitting Model Interspiro Thru Model Scott Thru w/ Schrader Fitting Model Survivair Thru w/ Schrader Fitting Model PLEASE NOTE: This chart is based on a majority of individuals wearing SCBA, safety helmet and suggested undergarments. Proper fit will vary with individual body shape. Page 3 of 14

4 Technical Data Package Ensemble or Element Ensemble Exhaust Valve External fitting Performance Requirement Liquid tight Integrity Overall ensemble function and integrity Test Method Requirement Result ASTM F1359 (Section 8.3) ASTM 1154 ASTM F1052 (Section 8.4) No Liquid penetration No liquid accumulation in outer gloves No liquid accumulation in outer boots Ending Suit pressure 80 mm water gauge 93.6 mm Test subject completes task Test subject has visual acuity of 20/35 or better through face piece lens and visor Time to remove and reinsert hands in glove 5 times 2 minutes. Air flow capacity Section 8.5 Internal suit pressure 150 mm water gauge Ending suit pressure 80 mm water gauge Overall inward Section 8.8 PPDFsys 488 leakage PPDFi (local) 1071 Exhaust valve mounting strength Exhaust valve inward leakage External fitting installation effect on integrity External fitting pullout strength Section 8.9 Strength > 135 N Section 8.24 Leakage rate <= 30 ml/min ASTM F1052 Ending suit pressure (Section 8.2) 80 mm water gauge Section 8.13 Strength > 1000 N MSA Dual Purpose Thru w/ Hansen Fitting Model MSA Quick Fill Thru w/ Schrader Fitting Model Draeger Thru w/ Hansen Fitting Model Interspiro Thru Model Scott Thru w/ Schrader Fitting Model Survivair Thru w/ Schrader Fitting Model mm water gauge mm water gauge PPDFsys Left Crotch N 0 ml/min 93.6 mm water gauge 3904 N 1815 N 5650 N 2389 N 3662 N 4074 N Page 4 of 14

5 Technical Data Package Suit Material Flame resistance ASTM F1358 Burst strength Puncture propagation tear resistance Cold temperature performance ASTM D751 (Section 8.10) ASTM D2582 (Section 8.11) ASTM D747 (Section 8.12) Suit Seam Breaking strength ASTM D751 (Section 8.22) Suit Closure Chemical ASTM F903 Penetration (Section 8.23) Breaking strength ASTM D751 (Section 8.22) Visor Material Flame resistance ASTM F1358 Visor high-mass impact resistance Cold temperature performance Section 8.27 Section 8.14 Visor seam Breaking strength ASTM D751 (Section 8.22) Glove Material Flame resistance ASTM F1358 Cut resistance ASTM F1790 (Section 8.15) Puncture ASTM F1342 resistance (Section 8.16) Cold temperature ASTM D747 performance (Section 8.12) Gloves Dexterity ASTM F2010 (Section 8.17) After flame time 2 seconds MD CD Strength > 200 N Tear resistance 49 N Warp (Wales) Fill (Courses) Bend moment Nm MD (Wale) CD (Course) Strength > 67 N/25mm No penetration of 15 liquid chemicals Strength > 67 N/25mm After flame time 2 seconds MD CD No full-thickness cracks, holes, or fractures Evidence of Damage, Including Breakage, Cracks, Tears, or Separation Strength > 67 N/25mm After flame time 2 seconds Blade travel distance 20 mm at 150 grams Puncture force 22 N Bend moment Nm Percent increase in bare handed control < 600 percent 0 second 0 second 1213 N 69 N 63 N Nm Nm 339 N/25 mm 243 N/25 mm 1 second 1 second 290 N/25 mm 0 seconds melting and 45 mm 31 N Nm 221 % Page 5 of 14

6 Technical Data Package Footwear upper material Footwear toe sections Footwear soles and heels Footwear puncture resistant device Footwear soles or ladder shanks Flame resistance Cut resistance Puncture resistance Impact resistance Compression resistance Abrasion resistance Slip resistance Puncture resistance ASTM F1358 ASTM F1790 (Section 8.15) ASTM F1342 (Section 8.16) ATM F2412 (Section 8.31) ASTM F2412 (Section 8.31) ISO 4649 (Section 8.19) ASTM F2913 (Section 8.21) ASTM F2412 (Section 8.30) After flame time 2 seconds Blade travel distance 20 mm at 350 grams Puncture force 36 N Impact resistance J Compression resistance 11,121 N Relative volume loss 250 mm 3 Coefficient 0.40 No puncture Bending resistance Section 8.20 Deflection 6 mm Page 6 of 14

7 Technical Data Package Optional Flash Fire Requirements Ensemble Garment material Visor Material Overall flash fire protection Heat transfer performance Flame resistance Heat transfer performance Flame resistance Section 8.25 ASTM F2700 (Section 8.18) ASTM F1358 ASTM F2700 (Section 8.18) ASTM F1358 After flame time 2 seconds Ending suit pressure 13 mm water gauge Test subject has visual acuity of 20/100 or better through face piece lens and visor HTP Rating 12 cal/cm 2 After flame time Burn distance 100 mm 2 seconds MD CD HTP Rating 12 cal/cm 2 After flame time 2 seconds Burn distance 100 mm MD CD 0 seconds 89.8 mm water gauge 28.1 cal/cm 2 0 second Burn distance 3 mm 0 second Burn Distance 2 mm 50.1 cal/cm 2 1 second Burn distance 9 mm 1 second Burn Distance 11 mm Page 7 of 14

8 Technical Data Package Optional Flash Fire Requirements Glove Material Footwear material Heat transfer performance Flame resistance Heat transfer performance ASTM F2700 (Section 8.18) ASTM F1358 ASTM F2700 (Section 8.18) HTP Rating 12 cal/cm 2 After flame time 2 seconds Burn distance 100 mm MD CD HTP Rating 12 cal/cm 2 47 cal/cm 2 0 second Burn distance 11 mm 0.1 second Burn Distance 13mm certified to NFPA 1991 Flame resistance ASTM F1358 After flame time 2 seconds Burn distance 100 mm certified to NFPA 1991 Page 8 of 14

9 Chemical Permeation Test Data Material or Seam tested Technical Data Package Tychem RF600 Aluminized Material Test Period Interval Cumulative Permeation (µg/cm 2 ) over Test Period Interval 0-15 min min min min 1 hour total Chemical/ Requirement < 2.0 < 2.0 < 2.0 < 2.0 < 6.0 Acetone <0.2 <0.2 <0.2 <0.2 <0.8 Acetonitrile <0.2 <0.2 <0.2 <0.2 <0.8 Acrolein <0.2 <0.2 <0.2 <0.2 <0.8 Acrylonitrile <0.2 <0.2 <0.2 <0.2 <0.8 Anhydrous Ammonia (gas) <0.2 <0.2 <0.2 <0.2 <0.8 1,3-Butadiene (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Carbon Disulfide <0.2 <0.2 <0.2 <0.2 <0.8 Chlorine (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Dichloromethane <0.2 <0.2 <0.2 <0.2 <0.8 Diethylamine <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Formamide <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Sulfate <0.2 <0.2 <0.2 <0.2 <0.8 Ethyl Acetate <0.2 <0.2 <0.2 <0.2 <0.8 Ethylene Oxide (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Hexane <0.2 <0.2 <0.2 <0.2 <0.8 Hydrogen Chloride (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Methanol <0.2 <0.2 <0.2 <0.2 <0.8 Methyl Chloride (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Nitrobenzene <0.2 <0.2 <0.2 <0.2 <0.8 Sodium Hydroxide, 50% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Sulfuric Acid, 96.1% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Tetrachloroethylene <0.2 <0.2 <0.2 <0.2 <0.8 Tetrahydrofuran <0.2 <0.2 <0.2 <0.2 <0.8 Toluene <0.2 <0.2 <0.2 <0.2 <0.8 Chemical Warfare Agents Sulfur Mustard, Distilled/ Requirement < 4.0 Sulfur Mustard, Distilled <0.20 Soman/ Requirement < 1.25 Soman <0.14 Optional Liquefied Gases* Chemical/ Requirement < 6.0 Ammonia (Liquefied) 0.14 Chlorine (Liquefied) 1.10 Ethylene Oxide (Liquefied) <0.05 *Liquefied chemical gases are only evaluated over 15-minute exposure period. Page 9 of 14

10 Chemical Permeation Test Data Material or Seam tested Technical Data Package Tychem RF600 Ensemble Visor Material (40 mil PVC, 5 mil Teflon FEP, 40 mil PVC) Test Period Interval Cumulative Permeation (µg/cm 2 ) over Test Period Interval 0-15 min min min min 1 hour total Chemical/ Requirement < 2.0 < 2.0 < 2.0 < 2.0 < 6.0 Acetone <0.2 <0.2 <0.2 <0.2 <0.8 Acetonitrile <0.2 <0.2 <0.2 <0.2 <0.8 Acrolein <0.2 <0.2 <0.2 <0.2 <0.8 Acrylonitrile <0.2 <0.2 <0.2 <0.2 <0.8 Anhydrous Ammonia (gas) <0.2 <0.2 <0.2 <0.2 <0.8 1,3-Butadiene (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Carbon Disulfide <0.2 <0.2 <0.2 <0.2 <0.8 Chlorine (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Dichloromethane <0.2 <0.2 <0.2 <0.2 <0.8 Diethylamine <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Formamide <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Sulfate <0.2 <0.2 <0.2 <0.2 <0.8 Ethyl Acetate <0.2 <0.2 <0.2 <0.2 <0.8 Ethylene Oxide (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Hexane <0.2 <0.2 <0.2 <0.2 <0.8 Hydrogen Chloride (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Methanol <0.2 <0.2 <0.2 <0.2 <0.8 Methyl Chloride (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Nitrobenzene <0.2 <0.2 <0.2 <0.2 <0.8 Sodium Hydroxide, 50% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Sulfuric Acid, 96.1% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Tetrachloroethylene <0.2 <0.2 <0.2 <0.2 <0.8 Tetrahydrofuran <0.2 <0.2 <0.2 <0.2 <0.8 Toluene <0.2 <0.2 <0.2 <0.2 <0.8 Chemical Warfare Agents Sulfur Mustard, Distilled/ Requirement < 4.0 Sulfur Mustard, Distilled <0.20 Soman/ Requirement < 1.25 Soman <0.14 Optional Liquefied Gases* Chemical/ Requirement < 6.0 Ammonia (Liquefied) 0.10 Chlorine (Liquefied) 0.73 Ethylene Oxide (Liquefied) <0.05 *Liquefied chemical gases are only evaluated over 15-minute exposure period. Page 10 of 14

11 Chemical Permeation Test Data Material or Seam tested Test Period Interval Technical Data Package Tychem RF600 Glove Material/Seam (Guardian IN-35 Neoprene side facing Kevlar knit outer glove tested with North Silver Shield/4H barrier liner) Cumulative Permeation (µg/cm 2 ) over Test Period Interval 0-15 min min 0-15 min min 0-15 min Chemical/ Requirement < 2.0 < 2.0 < 2.0 < 2.0 < 6.0 Acetone < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Acetonitrile < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Acrolein < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Acrylonitrile < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Anhydrous Ammonia (gas) < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 1,3-Butadiene (gas) < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Carbon Disulfide < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Chlorine (gas) < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Dichloromethane < 0.2 < 0.2 < 0.2 < 0.4 < 1 Diethylamine < 0.3 < 0.4 < 1.6 < 0.9 < 3.2 Dimethyl Formamide < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Dimethyl Sulfate < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Ethyl Acetate < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Ethylene Oxide (gas) < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Hexane < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Hydrogen Chloride (gas) < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Methanol < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Methyl Chloride (gas) < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Nitrobenzene < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Sodium Hydroxide, 50% w/w < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Sulfuric Acid, 96.1% w/w < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Tetrachloroethylene < 0.2 < 0.2 < 0.2 < 0.2 < 0.8 Tetrahydrofuran < 0.2 < 0.2 < 0.3 < 0.5 < 1.2 Toluene < 0.2 < 0.2 < 1.5 < 1.6 < 3.5 Chemical Warfare Agents Sulfur Mustard, Distilled/ Requirement < 4.0 Sulfur Mustard, Distilled <0.20 Soman/ Requirement < 1.25 Soman <0.14 Optional Liquefied Gases* Chemical/ Requirement < 6.0 Ammonia (Liquefied) 0.10 Chlorine (Liquefied) 0.50 Ethylene Oxide (Liquefied) < 0.05 *Liquefied chemical gases are only evaluated over 15-minute exposure period. Page 11 of 14

12 Chemical Permeation Test Data Material or Seam tested Technical Data Package Tychem RF600 Ensemble seam (outer Silver Surface) Test Period Interval Cumulative Permeation (µg/cm 2 ) over Test Period Interval 0-15 min min min min 1 hour total Chemical/ Requirement < 2.0 < 2.0 < 2.0 < 2.0 < 6.0 Acetone <0.7 <1.2 <1.5 <1.3 <4.7 Acetonitrile <0.2 <0.2 <0.2 <0.2 <0.8 Acrolein <0.2 <0.2 <0.2 <0.2 <0.8 Acrylonitrile <0.2 <0.2 <0.2 <0.2 <0.8 Anhydrous Ammonia (gas) <0.2 <0.2 <0.2 <0.2 <0.8 1,3-Butadiene (gas) <0.2 <1.0 <0.9 <0.9 <3.0 Carbon Disulfide <0.2 <0.2 <0.2 <0.2 <0.8 Chlorine (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Dichloromethane <0.2 <0.2 <0.2 <0.2 <0.8 Diethylamine <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Formamide <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Sulfate <0.2 <0.6 <0.7 <0.8 <2.3 Ethyl Acetate <0.2 <0.2 <0.2 <0.2 <0.8 Ethylene Oxide (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Hexane <0.2 <0.2 <0.2 <0.2 <0.8 Hydrogen Chloride (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Methanol <0.2 <0.2 <0.2 <0.2 <0.8 Methyl Chloride (gas) Nitrobenzene <0.2 <0.2 <0.2 <0.2 <0.8 Sodium Hydroxide, 50% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Sulfuric Acid, 96.1% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Tetrachloroethylene <0.2 <0.2 <0.2 <0.2 <0.8 Tetrahydrofuran <0.2 <0.2 <0.2 <0.2 <0.8 Toluene <0.2 <0.2 <0.2 <0.2 <0.8 Chemical Warfare Agents Sulfur Mustard, Distilled/ Requirement < 4.0 Sulfur Mustard, Distilled <0.20 Soman/ Requirement < 1.25 Soman <0.14 Page 12 of 14

13 Chemical Permeation Test Data Technical Data Package Material or Seam tested Tychem RF600 Visor Attachment Seam Test Period Interval Cumulative Permeation (µg/cm 2 ) over Test Period Interval 0-15 min min 0-15 min min 0-15 min Chemical/ Requirement < 2.0 < 2.0 < 2.0 < 2.0 < 6.0 Acetone <0.02 <0.02 <0.02 <0.02 <0.02 Acetonitrile <0.2 <0.5 <0.6 <0.6 <1.9 Acrolein <0.2 <0.2 <0.2 <0.2 <0.8 Acrylonitrile <0.4 <0.8 <0.8 <0.8 <2.8 Anhydrous Ammonia (gas) ,3-Butadiene (gas) <0.7 <1.2 <1.2 <1.1 <4.2 Carbon Disulfide <0.2 <0.2 <0.2 <0.2 <0.8 Chlorine (gas) <0.2 <0.2 <0.2 <0.2 <0.8 Dichloromethane <0.2 <0.2 <0.2 <0.2 <0.8 Diethylamine <0.02 <0.02 <0.02 <0.02 <0.02 Dimethyl Formamide <0.2 <0.2 <0.2 <0.2 <0.8 Dimethyl Sulfate <0.2 <0.4 <0.7 <1.5 <2.8 Ethyl Acetate <0.2 <0.2 <0.2 <0.2 <0.8 Ethylene Oxide (gas) <0.6 <1.3 <1.3 <1.4 <4.6 Hexane <0.2 <0.2 <0.2 <0.2 <0.8 Hydrogen Chloride (gas) <0.2 <0.7 <1.2 <0.9 <3.0 Methanol <0.2 <0.2 <0.2 <0.2 <0.8 Methyl Chloride (gas) <0.06 <0.06 <0.06 <0.06 <0.06 Nitrobenzene <0.2 <0.2 <0.2 <0.2 <0.8 Sodium Hydroxide, 50% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Sulfuric Acid, 96.1% w/w <0.2 <0.2 <0.2 <0.2 <0.8 Tetrachloroethylene <0.2 <0.2 <0.2 <0.2 <0.8 Tetrahydrofuran <0.2 <0.2 <0.3 <0.4 <1 Toluene <0.2 <0.5 <0.5 <0.7 <1.9 Chemical Warfare Agents Sulfur Mustard, Distilled/ Requirement < 4.0 Sulfur Mustard, Distilled <0.20 Soman/ Requirement < 1.25 Soman <0.14 Product safety information available upon request. This information corresponds to our current knowledge on this subject. It is offered solely to provide possible suggestions for your determination. It is not intended, however, to substitute for any testing you may need to conduct to determine for yourself the suitability of our products for your particular purposes. It is the user s responsibility to determine the level of risk and the proper protective equipment needed for the user s particular purpose. This information may be subject to revision as new knowledge and experience becomes available. Since we cannot anticipate all variations in actual end-use conditions, DUPONT MAKES NO WARRANTIES AND ASSUMES NO LIABILITY IN CONNECTION WITH ANY USE OF THIS INFORMATION. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any trademark or patent rights. Page 13 of 14

14 Technical Data Package Copyright 2017 E. I. du Pont de Nemours and Company., All rights reserved. The DuPont Oval Logo, DuPont, The miracles of science and all products denoted with or are trademarks of E. I. du Pont de Nemours and Company and its affiliates, unless otherwise attributed. HazMax is a registered trademark of Onguard Industries. Silver Shield /4H is a registered trademark of North products. HazProof is a registered trademark of Tingley Rubber Company. Guardian is a trademark of Guardian Manufacturing. Page 14 of 14