Sealing strips for concrete construction joints STOPO TYPE 3 catalog
|
|
- Maximillian Lamb
- 6 years ago
- Views:
Transcription
1 Sealing strips for concrete construction joints STOPO TYPE 3 catalog WARNING: please always refer to the latest versions of these documents as published on our web site up to date. INFO@STOPO.CA
2 CONTENTS STOPO TYPE 3 sealing strips page 3 STOPO TYPE 3.5 sealing strips page 6 STOPO TYPE 3.5V sealing strips page 8 Concrete surface preparation and installation procedure, for sealing strips of TYPE 3, 3.5, 3.5V and L, bonding by thermal fusion pages Sealing joint around pipe into formwork and pipe opening sealing and repair through concrete wall pages STOPO TYPE L sealing strips (2 perpendicular surfaces with crushed stone) page 18 Type 0 (no stone) page 22 OTHER: Fusion of PVC waterstops and STOPO sealing strips page 23 FOR TECHNICAL DATA SHEET and MATERIAL SAFETY DATA SHEET STOPO SEALING STRIPS AND STOPO PREPARATION LIQUID FOR CONCRETE SURFACES: Please refer to the specific catalog in a distinct file. INFO@STOPO.CA
3 Sealing strips for concrete joints STOPO TYPE 3 The STOPO TYPE 3 sealing strips are used in construction joints (concreting on hard concrete). They are most efficient when low movement due to moderate shrinkage of concrete is expected. A concrete surface preparation must be done before bonding the strips. First, dust and laitance must be removed from the surface. Then a rubberized adhesive consisting of "STOPO LIQUID FOR SURFACE PREPARATION OF CONCRETE is applied and must dry. Finally, the strips are heated and bonded to the concrete, using a propane gas torch with a steel extension kit Dimensions: Models 1 Length 2 Width 3 Thickness Maximum advisable water head mm 23 mm 2 meters mm 23 mm 3 meters mm 33 mm 4 meters mm 23 mm 5 meters mm 105 mm 125 mm 75 mm 105 mm 43 mm 23 mm 23 mm 43 mm 43 mm 1s 9 meters 12 meters 15 meters 20 meters mm 43 mm 20 meters +
4 STOPO TYPE 3 sealing strip example of installation over a construction joint 25 mm min. New concrete placement 25 mm min. O Hard concrete Showing STOPO TYPE 3 sealing strip bonded to hard concrete surface by a thermo-fusion process. The sealing strip model is selected according to the water head. The selected model dimensions also depend on the available space between reinforcing bars. The STOPO TYPE 3 sealing strips are used commonly to perform cold construction joints (new concreting on hard concrete), where expected movement in concrete is limited to shrinkage, e.g. raising walls in reservoirs, basins, building new concrete structures on existing foundations, jointing slabs to walls at intermediate level, watertightness of pipe insert through walls, raising footings and foundations, etc
5 Horizontal «cold» construction joint using STOPO TYPE # sealing strip Use for: concreting on hard concrete Concreting of a new slab STOPO type sealing strip bonded to hard concrete and over existing saw cut joint 40 mm deep saw cut joint filled with a polyurethane sealant for concrete Existing slab
6 Sealing strip for concrete joints STOPO TYPE The choice of STOPO TYPES 3,5 et 3,5V sealing strips compared to TYPE 3 is done in the case of greater anticipated movements in concrete. TYPE 3,5 for shear movement and TYPE 3,5V for tensile movement. 1 3a 3b Dimension: Dimensions: Modèles Models 1 1 Longueur Length 2 2 Largeur Width 3a 3a Épaisseur Thickness a 3b 3b Épaisseur Thickness b Tête Maximum d eau advisable recommandé water head mm 18 mm 15 mm 5 meters mm 23 mm 20 mm 1s mm 23 mm 20 mm 15 meters mm 23 mm 20 mm 20 meters
7 STOPO TYPE 3.5 Joining new structures to existing structures Joining new slab to existing or just built wall at any intermediate level Joining-extending a new slab to an existing slab Joining new wall to an existing or just built wall TYP. 25 mm minimum TYP. Sealing strip STOPO # New slab extension or wall Existing slab or wall es This application may be used either on a horizontal or vertical joint. The TYPE 3.5 sealing strips are more effective in shear strength movement. Second concrete Béton frais placement Initial concrete Béton dur placement
8 Sealing strip for concrete joints STOPO TYPE 3.5V The STOPO TYPE 3.5V sealing strips are suitable for construction joints for walls or slabs. Their wider elastic range allows them to be installed where construction joints require greater movements in concrete, especially in tensile strength. The choice of STOPO TYPES 3,5 et 3,5V sealing strips compared to TYPE 3 is done in the case of greater anticipated movements in concrete. TYPE 3,5 for shear movement and TYPE 3,5V for tensile movement. 3a 1 3b 2 Dimensions: Models 1 Length 2 Width 3a Thickness 3b Thickness Maximum advisable water head 33040V 30 mm 23 mm 20 mm 3 meters 34060V 40 mm 33 mm 30 mm 7 meters 35060V 50 mm 33 mm 30 mm 15 meters
9 STOPO TYPE 3,5V vertical construction joint Joining new wall to existing wall 25 mm minimum 35060V This method is applied to a vertical joint. This is an example of a typical installation. It is the designer s responsibility to determine the set up and select the type and dimensions of the material and installation of the construction joint, according to the requirements and restraints for the work. We recommend that the strips be supported until the concrete placement has been completed. This TYPE 3,5V sealing strip is more effective in tensile strength. 2 2e coulée 2 nd concrete placement Initial concrete placement
10 STOPO TYPE 3 selection table Type 3 Type 3.5 Sealing strips For joining Max. tensile Max. shear Max. water head STOPO models concrete surfaces advisable advisable advisable new to hard 1 mm 2 mm 2 meters new to hard 1 mm 2 mm 3 meters new to hard 1 mm 2 mm 4 meters new to hard 1 mm 2 mm 5 meters new to hard 2 mm 3 mm 1s new to hard 1 mm 3 mm 9 meters new to hard 1 mm 3 mm 12 meters new to hard 2 mm 4 mm 15 meters new to hard 2 mm 7 mm 20 meters new to hard 2 mm 7 mm 20 meters new to hard 2 mm 4 mm 1s new to hard 3 mm 7 mm 15 meters new to hard 3 mm 10 mm 20 meters Type 3.5V 33040V new to hard 2 mm 2 mm 3 meters 34060V new to hard 4 mm 4 mm 7 meters 35060V new to hard 6 mm 4 mm 20 meters ADDITIONAL INFORMATION ABOUT 3.5 AND 3.5V TYPES: The strip types that are made longer than wide (3.5V TYPES) absorb greater tensile strength movements since the elastic capacity is greater in the direction of the longer side of the strip. For example, a 35060V strip (shown: 1a, 1b) will have a more effective tensile strength than a strip (shown: 2a, 2b). On the other hand, the strip types that are made wider than long (3.5 TYPES) absorb greater shear strength movements since the elastic capacity is greater in the direction of the strip width as installed. For example, a strip (shown in 2a and 2b) will have a more effective shear strength than a 35060V strip (shown in 1a and 1b). 1 a 1 b 2 a 2 b (819)
11 STOPO sealing strips of TYPES V and «L» Installation procedure by thermal fusion. Useful tools to have on hand when installing these types of sealing strip 1. Bush hammer bits (examples shown) on drill. 2. Richard «Combination tool Ergo-grip» (knife) ( 3.GOSS KP-155-H DETAIL TORCH KIT used with propane gas tank and long hose (6 to 8 meters, 20 to 25 feet long). 4. Industrial vaccuum cleaner
12 STOPO sealing strips of TYPES V and «L» Installation method by thermal fusion (works on concrete and metallic surfaces) FIRST REFER TO OUR LIST OF SUGGESTED TOOLS TO PERFORM BEST INSTALLATION STEP 1: 2 1. The existing concrete surface should be cleaned and conditioned to remove laitance and any loose particles, by slight bush hammering, using a bush hammer bit on percussion tool. Pass vacuum cleaner. STEPS 2 and 3: 2. Using a detail torch kit, slightly warm up the concrete surface. 3. Apply a bed of STOPO PREPARATION LIQUID FOR CONCRETE SURFACE slightly wider than the waterstop (strip) base, using a paint brush or roller. LET DRY before proceeding to next step. STEP 4: 4. Because the STOPO PREPARATION LIQUID needs time to dry and due to other construction restraints, it may happen that the sealing strips be installed only after a certain delay. In the meantime, some dampness might have appeared to the concrete surface. When this is the case, just prior to the installation of the strips, it might be necessary to to warm up again and dry the surface of the concrete with the detail torch. Caution: when this operation is necessary, make sure that the STOPO LIQUID is dry and inert before heating the surface since IT IS VERY FLAMMABLE wet STEP 5: BONDING THE SEALING STRIPS TO CONCRETE: 5a With the detail torch, heat up the bituminous surface of the strips to a slight liquefaction stage. Also heat up the free ends. 5a 5b 5b Then press the strips firmly onto the concrete surface, accomplishing at the same time butt splicing by thermally fusing the free ends together. For a vertical joint, proceed (in the sealing strip installation) from bottom to top. Hint: for a vertical joint, sometimes it may be easier and more effective to cut the standard made long strip and work up with plus or minus half-lengths. Followed on next page a description of the method to cut and splice easily sealing strip lengths using the heated knife. NOTE: The STOPO sealing strips also work very well on steel or metallic structures and surfaces, and in these cases, the STOPO preparation liquid IS NOT NECESSARY. Warning: never attempt to stretch the long strip to reach a junction point. Always cut the necessary length into a new strip and accomplish butt splicing by thermally fusing the cut free ends together using the method shown on page 13.
13 Butt joint and splicing the «STOPO» sealing strips Butt splicing in any direction (lateral, longitudinal or perpendicular) is accomplished by first removing stone and/or cut the strips to the required dimensions, using a heated knife blade, then by thermally fusing the free ends or bituminous exposed surfaces obtained, pressing them together firmly. Heating the blade of a «Richard Combination Tool Ergo-grip knife» with the detail torch makes it easy to scratch the surface of, cut or splice the STOPO sealing strips. Scratching the surface with the heated knife blade to remove stone prior to thermally fusing of strip ends and sides in any direction. Bituminous exposed ends or strip sides are heated to a slight liquefaction stage and pressed together to create sealing strip joints in any direction.
14 This is an example of how the STOPO preparation liquid for concrete surfaces has been spread over the concrete surface and has dried adequately. The surface has thus been prepared and is now ready for the bonding of STOPO TYPE 3 sealing strips by the thermo-fusion process.
15 Construction joint installation on hard concrete with STOPO type 3 sealing strip
16 Sealing joint around a pipe into formwork Procedure for concrete pipe 1. The preparation of the pipe surface is most important. First roughen contact surface and remove laitance or any loose particle with a steel brush or grinder. Working with mechanical tools is most effective. Make sure to clean and remove any dust residues following the contact surface preparation. 2. With a propane gas detail torch kit, warm up the surface of the concrete and make sure that any dampness is eliminated. 3. With a paint brush, apply a thin bed of the STOPO PREPARATION LIQUID FOR CONCRETE SURFACE (not required for metal and plastic pipes) over the warm concrete surface. LET DRY before proceeding to next step. 4. With the detail torch, heat up the bituminous surface of the STOPO TYPE 3 strips to a slight liquefaction stage. Press the strips evenly over contact surface of pipe with the hands. If more than the standard strip length is needed to go around the pipe, then proceed with butt splicing and thermally fusing the free ends together, using Ergo-Grip knife and torch as described in the previous pages. Do not overlap the free ends of strips. Cut off the excess length and bond the free ends together by thermally fusing. Procedure for steel or metal pipe 5. Proceed with STEPS 1, 2 and 4 as for concrete pipe. Same as for concrete pipe except for STEP 3 that is not required in the case of metal. The STOPO preparation liquid (for concrete surfaces) is not necessary for steel or metallic pipes. Procedure for plastic pipes 6. Proceed with STEPS 1. AND 4. only as for concrete pipe. Do not warm up the plastic pipes with the detail torch. Also, in the case of plastic pipes, DO NOT apply any STOPO PREPARATION LIQUID. Roughen the plastic pipe surface with sandpaper or steel brush. The sealing strips may be installed side by side on the pipe. The model and the number of strips required are determined according to the water head and the pipe operation (pressure, vibration stress, others). The minimum concrete cover between the exterior surface of the concrete structure and the outer side of the sealing strip must have 65 mm to ensure full effectiveness of the strips. NOTE: pressure pipes MUST be mechanically anchored to the concrete structure outside of the joint away from the sealing strips. 65 mm minimum (819)
17 Repairing and sealing a pipe opening through a wall or any concrete structure using STOPO TYPE 3 sealing strips New concreting Compacted soil 65 mm minimum 65 mm minimum Existing wall Repairing and sealing a pipe opening through wall 1. Coarsely break the concrete surface. 2. Refer to STEP 1 in the installation procedure by thermal fusion for the concrete wall surface preparation. 3. Proceed first by bonding the sealing strips to the concrete wall surface. 4. Insert pipe to its final position through opening in wall and bond the sealing strips around pipe. 5. Build the formwork for a block around pipe and pour concrete. 6. This method will ensure effective seal tight connection of large pipes through manholes or reservoirs. 7. Caution: for high pressure pipes, the designer must consider anchoring the pipes to the concrete structure.
18 Sealing strips for concrete joints STOPO TYPE «L» STOPO TYPE «0» WARNING: please always refer to the latest versions of these documents as published on our web site up to date.
19 STOPO TYPE «L» sealing strips Standard dimensioned models offered: L5040 and L3030 STOPO TYPE L sealing strips 43 mm (L5040) 33 mm(l3030) 53 mm (L5040) 33 mm (L3030). Refer to the installation method by thermal fusion. The same method (as for TYPE 3) is used for TYPE L sealing strip, heating up both bituminous surfaces to bond either to concrete or metallic surfaces. This TYPE L sealing strip is used to repair deteriorated slabs and footings. For example, it is thus possible to pour a new concrete slab over a slab that has defective (leaking) construction joints This TYPE L sealing strip, combined with our STOFLEX closed-cell expansion joint filler, will ensure sealtightness at immediate fluid arrival. It is also possible to build construction joints on top of the new slab by first placing a STOPO TYPE 3, model sealing strip (see this detail on page 5) over the existing slab aligned with the new construction joint. It is otherwise possible to install this TYPE L strip along with a metal waterstop for increased sealtightness protection.
20 Joining new slab to existing slab and wall using STOPO TYPE L sealing strip New concreting over existing concrete. Option: our STOFLEX closed-cell expansion joint filler works very well when combined to the STOPO sealing strips. In this case, a 50 mm wide STOFLEX, leaving a 12,5 x 10 opening at top of slab to insert a caulking sealer. STOPO TYPE L sealing strips STOPO sealing strip L5040 (L3030 available) New slab 100 mm (example) Existing structure
21 Polyethylene Closed-cell Expansion Joint Filler Made in Canada, STOFLEX is a modern and easy to install expansion joint filler and separation joint for concrete structures and foundations, such as slabs, walls, bridges, sidewalks, swimming pools and other. It is designed to effectively replace conventional asphalt expansion joint board. It provides effective protection against the development of cracks in concrete slabs and foundations by vibrations from earthquakes or machinery operations that cause knocking between two independent concrete surfaces. STOFLEX also serves as a barrier against dirt, insects and moisture in joints. STOFLEX is made of closed-cell polyethylene. It is waterproof and ultraviolet stable, it resists to chemicals such as acids, hydrocarbons, chlorinated solvents, petroleum, paints, varnishes, thinners and alcohols. STOFLEX is prepared in different widths according to construction work specifications and comes with a ½ x ½ pre-slit removable strip to insert a caulking sealer on top of the joint. STOFLEX is light and flexible, thus provides easy storage and handling on site, and simple installation, in comparison to heavy and rigid asphalt expansion joint boards. STOPO - STOFLEX TECHNICAL DATA: PROPERTIES TYPICAL VALUE TEST METHOD COLOR: coal grey DENSITY RANGE 1,5-1,9 lb/ft³ ASTM-D TENSILE STRENGTH ASTM-D T (md) 44 psi (cmd) 26 psi COMPRESSIVE STRENGTH ASTM-D D (vertical direction) 5,2 25% 13,4 50% WATER ABSORPTION < 0,1 lb/ ft 2 ASTM-D L (on cut surface) TEMPERATURE STABILITY -40 F to 180 F TEAR RESISTANCE ASTM-D G (md) 10 lb/in. (cmd) 15 lb/in. Packaging Dimensions ½" x 2" x 50 ½" x 3" x 50 ½" x 4" x 50 ½" x 5" x 50 ½" x 6" x 50 ½" x 7" x 50 ½" x 8" x 50 ½" x 9" x 50 ½" x 10" x 50 ½" x 11" x 50 ½" x 12" x 50.and other available dimensions up to 48" wide. STOPO: 255, Francois-Bourgeois st., Victoriaville, QC G6T 2G9 Phone (819) Fax (819)
22 STOPO TYPE 0 (no stone) The STOPO TYPE 0 (no stone on) sealing strips or plaques are used to seal between two separate hard concrete structures. They may be used also to seal between concrete and steel surfaces. They are efficient when low structural movement is expected. As advised for TYPE 3 installation method, laitance, dust and any loose particles must be cleaned off from the surfaces in contact with the strips. The same installation method as for the TYPE 3 sealing strips, by thermal fusion, is used. STOPO TYPE O sealing strips Dimensions of and available models 1 Length 2 Width 3 Thickness From # from 30 mm from 20 mm TO TO TO # mm 60 mm This table shows that the available dimensions are variable and thus produced according to the work and the customers needs and on demand only.
23 Joining PVC waterstops and STOPO sealing strips 1. Heat up the blade of the Richard «Combination tool Ergo-grip» (knife) with a propane gas torch. 2. With the hot knife blade, make a cut into the STOPO strip half deep only and to separate it into two parts. Joining PVC waterstop and STOPO 3. With the torch, heat up the inside of the strip cut until slight liquefaction appears at bottom of cut. 4. Immediately insert the PVC waterstop inside the STOPO strip opening. 5. Apply hand pressure along the sides of the STOPO strip to the PVC waterstop. A bitumen cord should appear on the surface if the STOPO strip was well heated. Maintain this pressure during few minutes. checking that the bitumen has fully integrated the roughness of the PVC waterstop surface.
24 Limited warranty: The STOPO products are guaranteed against manufacturing defects. If products had to be defective, the warranty is limited to replacement of products before their confinement in concrete. Misuse and poor storage void this warranty.
The complete version of this catalog is under process. For the time being, we present you a brief description of the TYPE 4 model and the supports.
2015-04-14 1 Sealing strips for concrete construction joints STOPO TYPE 4 catalog and PCJS and PCJW, galvanized steel supports for Planned Control Joints in Slab or Wall The complete version of this catalog
More informationA. The work of this section includes, but is not limited to, the following:
SECTION 07 14 00 FLUID APPLIED WATERPROOFING SYSTEM PART 1: GENERAL 1.1 RELATED DOCUMENTS A. All of the Contract Documents, including General and Supplementary Conditions and Division 01 General Requirements,
More informationStudent Services & Classroom Addition
SECTION 071326 - SELF-ADHERING SHEET WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationPERMANENT PAVEMENT REPAIR NO SCALE
SAWCUT EXISTING PAVEMENT 2" BITUMINOUS CONCRETE SURFACE COURSE, CLASS 2 (MIN) CLEAN EDGE PRIOR TO PAVING AND PAINT WITH LIQUID BITUMEN. INSTALL SEALANT OVER JOINT UPON COMPLETION 2" BITUMINOUS CONCRETE
More informationDUAL EXPANSION. facilitate casting and ensure the total filling of voids even in tight or complex spaces and when working on large surfaces.
Fluid expansive mortar for precision anchoring of machinery and structural elements LAYER THICKNESS FROM 1 TO 10 CM REFURBISHMENT and PROTECTION Line Expansive cement-based mortar for anchoring and grouting
More informationSPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay
2004 Specifications SPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay 1. Description. Furnish and place a multi-layer polymer overlay consisting of a crack seal, polymer resin and aggregates.
More informationDusit Roongsang, P.E. Presented at. PNWS AWWA Conference Bellevue, WA May 1, 2015
Dusit Roongsang, P.E. Presented at PNWS AWWA Conference Bellevue, WA May 1, 2015 Not waterproof structures Leakage rate is suitable for intended use Contain water Prevent contamination of contents Prevent
More informationSealArm Tape TPE. Building & Joint Sealants T E C H N I C A L D A T A S H E E T. Uses. Features and Benefits
Product Description is a high performance Joint Tape system for expansion, it can be used for connection joints as well as for cracks, when fixed to the joint, allows irregular and high movement in more
More informationADEKA ULTRA SEAL KBA-1510FP
ADEKA ULTRA SEAL Hydrophilic Vulcanized Rubber cross section - 15mm X 10mm - 5/8" X 3/8" 82 feet per case 20mm 15mm Dry Fully Hydrated Low expansion pressure - suitable for limited concrete coverage (1.0")
More informationSECTION RIGID PAVEMENT
SECTION 02750 PART 1 GENERAL RIGID PAVEMENT 1.1 SUMMARY A. Section Includes: 1. Concrete sidewalks. 2. Concrete stair steps. 3. Concrete integral curbs gutters. 4. Concrete parking areas and roads. B.
More informationPreventing Water Leakage through Construction Joints using SYNKOFLEX Preformed Compressible Waterstop
Preventing Water Leakage through Construction Joints using SYNKOFLEX Preformed Compressible Waterstop Introduction A typical problem in most Water Retaining Structures is the leakage of water through Construction
More informationSection Pre-Applied Sheet Membrane Waterproofing
Section 071324 Pre-Applied Sheet Membrane Waterproofing PART 1 GENERAL 1.01 SUMMARY A. The Work of this Section includes, but is not limited to, pre-applied sheet membrane waterproofing that forms an integral
More informationSECTION CONCRETE ACCESSORIES
SECTION 03250 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Requirements for providing concrete accessories shown and specified herein such as waterstops, dovetail anchor slots, cast-in-place reglets,
More informationDIVISION 7 - THERMAL AND MOISTURE PROTECTION Section Joint Sealers Elastomeric and non-elastomeric Sealant
Spec Component: SC-071NSEZ-03/10 Sikaflex-2c NS EZ Part 1 - General DIVISION 7 - THERMAL AND MOISTURE PROTECTION Section 07900 Joint Sealers Elastomeric and non-elastomeric Sealant 1.01 Summary A. This
More information220 E. General Robinson St. Pittsburgh, PA fax
C CETCO Waterstop-RX... 7 G GREENSTREAK Hydrotite Waterstop... 5 Leakmaster LV-1... 5 PVC Waterstop... 3, 4 Swellstop... 8 H HYDROTITE WATERSTOP... 5 L LEAKMASTER LV-1... 5 P PVC WATERSTOP... 3, 4 S SWELLSTOP...
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationSECTION (07100) - DAMPPROOFING AND WATERPROOFING
SECTION 07 10 00 (07100) - DAMPPROOFING AND WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Sheet Membrane Waterproofing 2. Under-Slab-On-Grade Vapor Barrier B. Related Sections: 1.02
More informationSHEP POXY ROADS & HIGHWAYS FAST SET HIGH MODULUS, STRUCTURAL, EPOXY GEL
SHEP POXY ROADS & HIGHWAYS FAST SET HIGH MODULUS, STRUCTURAL, EPOXY GEL Product Description SHEP POXY ROADS & HIGHWAYS FAST SET is a 2- component structural epoxy system that offers exceptional strength
More information1-part elastic joint sealant and multipurpose adhesive
Product Data Sheet Edition 31/10/2006 Identification no: 02 05 01 01 005 0 000001 1-part elastic joint sealant and multipurpose adhesive Construction Product Description Uses Characteristics / Advantages
More informationInstallation Guide Wall Panels
Installation Guide Wall Panels Jointless or Dry-Stacked Installation (Read Prior to installation) The MStone system is a jointless / dry-stacked installation where panels and corners fit tightly together
More informationCONCRETE WORK CONCRETE WORK. Underground Electric Distribution Standards I. SCOPE APPLICABLE STANDARDS
Underground Electric Distribution Standards I. SCOPE This section includes the standards for concrete, reinforcing steel, formwork, concrete placement, curing, and construction joints. Concrete work for
More informationSECTION JOINT SEALERS 1.03 THIS SECTION INCLUDES JOINT SEALERS FOR THE FOLLOWING LOCATIONS:
PART 1 - GENERAL 1.01 RELATED DOCUMENTS: SECTION 07900 - A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this
More informationPITTWRAP CW PLUS JACKETING Product Datasheet
PITTWRAP CW PLUS JACKETING Product Datasheet 1. Description and Area of Application PITTWRAP CW PLUS jacketing is a 1.27 mm (50 mil) thick self-sealing, modified bituminous membrane for protecting underground
More informationUNIVERSITY OF MISSOURI General Concrete Requirements - Waterproofing 2017 Q3
GENERAL: The scope of this document is to provide instruction for the installation of waterproofing of concrete steam chases, tunnels and manholes. DESIGN GUIDELINES: A. General 1. Outside surfaces of
More informationSECTION UNIT PAVERS
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Concrete pavers. 2. Detectable warning pavers. 3. Warning stripe pavers. 1.2 SUBMITTALS A. Product Data: For the following: 1. Pavers.
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE & HANDLING: Check for damage that may have occurred during transit. Keep receptor flat on pallet, as it was shipped, until ready to install.
More informationSECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS
SECTION 03 05 00 COMMON WORK RESULTS FOR CONCRETE 09 97 00 SSPECIALTY COATINGS Weld Crete ************************************************************************************************************************
More informationDIVISION 7 - THERMAL AND MOISTURE PROTECTION Section Joint Sealers Elastomeric and non-elastomeric Sealant
EZ Spec Component: SC-071NSEZ-03/10 Sikaflex-2c NS Part 1 - General DIVISION 7 - THERMAL AND MOISTURE PROTECTION Section 07900 Joint Sealers Elastomeric and non-elastomeric Sealant 1.01 Summary A. This
More informationAVM System 500. Aussie Membrane 500
Generic Spec TECH DATA SHEET Sections - 071000 / 071400 / 071416 ICC ESR-2503 L.A. RR#: 25550 Heavy Duty Below Grade Bituminous Waterproofing Membrane Sections 071000 / 071400 / 071416 Fluid Applied Waterproofing
More informationAVM System 500. Aussie Membrane 500
Generic Spec TECH DATA SHEET Sections - 071000 / 071400 / 071416 ICC ESR-2503 L.A. RR#: 25550 Heavy Duty Below Grade Bituminous Waterproofing Membrane Sections 071000 / 071400 / 071416 Fluid Applied Waterproofing
More informationCONSTRUCTION SPECIFICATION FOR CONCRETE PAVEMENT AND CONCRETE BASE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 350 MARCH 1998 CONSTRUCTION SPECIFICATION FOR CONCRETE PAVEMENT AND CONCRETE BASE 350.01 SCOPE 350.02 REFERENCES 350.03 DEFINITIONS TABLE OF CONTENTS
More informationConstruction. High performance joint sealing system. Product Description. System Data Sheet Edition _1. 1 Sikadur Combiflex SG system 1/8
System Data Sheet Edition 2012-05_1 High performance joint sealing system Construction Product Description Uses High performance joint sealing system for construction, expansion and connection joints as
More informationCHARACTERISTICS / ADVANTAGES
PRODUCT DATA SHEET Flexible PVC Waterstops PRODUCT DESCRIPTION Flexible PVC waterstops used to seal construction and expansion joints in concrete structures. Sika -Waterbars are available in different
More informationSECTION RIGID PAVEMENT. 1. Portland Cement Concrete (PCC) pavement. 2. Section Aggregate Base Course.
SECTION 02750 RIGID PAVEMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Portland Cement Concrete (PCC) pavement. B. Related Sections: 1.2 REFERENCES 1. Section 02315 Excavation. 2. Section 02721
More informationFIVE STAR PRODUCTS, INC. (800)
FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 Page 1 of 15 DESIGN-A-SPEC GUIDELINES FIVE STAR STRUCTURAL CONCRETE CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS
More informationKIM Best Practices Guide for Shotcrete Nov 2013
Contents 1. What This Document Is For 2. Materials You Will Need 3. Receiving Surfaces For Shotcrete 4. Pre-Shoot Inspection and Preparation 5. Control Joint Spacing 6. How to Install Control Joints o
More information.2 Flashings at grade to extents shown on the Drawings. .3 Membrane and polyethylene slip sheets at perimeter of walls.
RWPS Foundations and Concrete Structures Page 1 of 8 1. GENERAL 1.1 Work Included.1 Supply and installation of ethylene propylene diene monomer (EPDM) membrane and insulation to extents shown on the Drawings
More informationPacific Polymers Elasto-Deck 5000MR Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000MR OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide
More informationRLA CERAMIC TILE ADHESIVE 10 year Limited Warranty
RLA CERAMIC TILE ADHESIVE 10 year Limited Warranty RLA Polymers Pty Ltd; undertakes to warranty Resinflex (or RLA Flex 2- Part), and RLA Flex 1-Part, when used to install tiles over Protectowrap AFM for
More informationInstallation Manual. Foundations. Version 2
Installation Manual Foundations Version 2 Contents Overview...1 Planning the Job... 2 Introducing DMX FlexSheet...2 Supplies Required...3 Tools Required...4 Preparing the Site...4 Where to Start?...5 Installing
More informationBITUTHENE 3000 and BITUTHENE Low Temperature Below-Grade
BITUTHENE 3000 and BITUTHENE Low Temperature Below-Grade Self-adhesive, rubberized asphalt/polyethylene waterproofing membranes for basements and sub-structures Product Description BITUTHENE 3000 and BITUTHENE
More informationSECTION CAST-IN-PLACE CONCRETE
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 03 30 00 CAST-IN-PLACE CONCRETE A. Cast-in-place concrete building frame members, floors, shear walls, elevator shaft walls, foundation walls, footings, and
More informationDon t Let Your Concrete Waterproofing Slip Through the Cracks KRYTON DECEMBER 2008
KRYTON DECEMBER 2008 Concrete is the world s most commonly utilized building material. It s used in residential and commercial construction, bridges and roadways, water containment, sidewalks, driveways
More informationSECTION STORM DRAINAGE
SECTION 02720 STORM DRAINAGE PART 1 - GENERAL 1.01 WORK INCLUDED A. Trenching and other excavation. B. Ground water control. C. Pipe bedding. D. Installation of storm drains and appurtenances. E. Installation
More informationSECTION MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof
SECTION 07550 MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof This section is based on the products of MFM Building Products Corp., which is located at: 525 Orange St. P. O. Box 340 Coshocton, OH 43812
More informationCS-75 Water-Based Adhesive Surface Primer
CS-75 Water-Based Adhesive Surface Primer Enhances the bonding between preformed sealants and concrete surfaces aiding in the installation process. Stops water penetration of the concrete. Conveniently
More informationPacific Polymers Elasto-Deck 5000X2 Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000X2 OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide
More informationACO DRAIN Site Installation Manual
ACO Construction & Building Products EXPANSION JOINT TO ENGINEER S DETAILS CONCRETE ACO DRAIN Site Installation Manual Fiberglass Drain Systems Getting Started ACO Drain consists of a full range of modular
More information1-part elastic joint sealant and multipurpose adhesive
Product Data Sheet Edition 23/08/2006 Identification no: 01 05 01 01 005 0 000001 Sikaflex -11 FC + 1-part elastic joint sealant and multipurpose adhesive Construction Product Description Uses Characteristics
More informationPVC WATERSTOPS. TYPES OF CONCRETE JOINTS Expansion (Isolation) Joint. Contraction (Control) Joint
PVC WATERSTOPS TYPES OF CONCRETE JOINTS Expansion (Isolation) Joint A joint that separates the slab structurally from other building elements such as walls, columns, foundations, drain pipes, to accommodate
More informationINDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES. Four-Side Interlock Loose Lay Installation
INDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES Four-Side Interlock Loose Lay Installation The following pages are guidelines only... please read this manual thoroughly
More informationWabo ElastoFlex - EFJ/EFJ-C Horizontal Expansion Joint System
Installation Procedure Last Updated: May 16 th, 2018 Wabo ElastoFlex - EFJ/EFJ-C Horizontal Expansion Joint System The following installation procedure is very important and must be fully understood prior
More informationSECTION CONCRETE PAVING
SECTION 32 13 13 PART 1 - GENERAL 1.01 DESCRIPTION A. This Section describes the requirements for providing portland cement concrete work and all other incidental concrete improvements for the project
More informationConstruction. Flexible PVC waterstops. Product Description. Product Data. Tests. Form. Storage. Technical Data
Construction Product Data Sheet Edition 2016-07_1 Flexible PVC waterstops Product Description Uses Characteristics / Advantages Flexible PVC waterstops used to seal construction and expansion joints in
More information1-part elastic joint sealant and multipurpose adhesive
Product Data Sheet Edition 15/11/2005 Identification no: 02 05 01 01 005 0 000001 1-part elastic joint sealant and multipurpose adhesive Construction Product Description Uses Characteristics / Advantages
More informationDMX AG AIR-GAP MEMBRANE. Section Damproofing and Waterproofing
DMX AG AIR-GAP MEMBRANE Section 07 10 00 Damproofing and Waterproofing NOTE TO SPECIFIER: These specifications were current at the time of publication but are subject to change at any time without notice.
More informationDIVISION 7 - THERMAL AND MOISTURE PROTECTION Section Joint Sealers Elastomeric and non-elastomeric sealant
Spec Component: SC-073-03/11 Sikadur Combiflex SG Part 1 - General DIVISION 7 - THERMAL AND MOISTURE PROTECTION Section 07900 Joint Sealers Elastomeric and non-elastomeric sealant 1.01 Summary A. This
More informationWabo FireShield Model: FSH
Wabo FireShield Model: FSH Horizontal Expansion Control Fire Barrier System The following installation procedure is very important and must be fully understood prior to beginning any work. To ensure proper
More informationSLAB ON GRADE Insul-Joint or Expansion Joint Material as Required by A/E Specifications AquaCheck Liquid Coating 400 (Waterproofing Membrane) with Aqu
INSTALLATION INSTRUCTIONS Note: The following installation instructions are based off of ASTM E 1643 (Standard Practice for Installation of Water Vapor Retarders Used in Contact with Earth or Granular
More informationApplications. Properties. Swelling capacity in contact with water. Density. Weight
Grace Construction Products Bentoject Product Description Bentoject is the combination of a hydrophilic bentonite strip and a post-injectable injection tube into one system as a high performance waterstop
More informationSikadur- Combiflex SG. High Performance Crack, Construction and Expansion Joint Waterproofing System
Sikadur- Combiflex SG High Performance Crack, Construction and Expansion Joint Waterproofing System Sikadur-Combiflex SG System High performance joint sealing system for construction, expansion and connection
More information1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels. 3. Insulation. 4. Plaza deck pavers.
SECTION 071413 HOT FLUID APPLIED RUBBERIZED ASPHALT WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels.
More informationKU Design Guidelines APPENDIX II PERMEABLE BITUMINOUS PAVEMENT
PERMEABLE BITUMINOUS PAVEMENT PART 1: GENERAL 1.01. RELATED DOCUMENTS: A. Drawings and general provisions of Contract, including Special Requirements General Conditions and Division 1 Specifications Sections,
More informationCORROSION ENGINEERING SPECIFICATION FOR INSTALLATION
AN ERGONARMOR COMPANY TECHNICAL INFORMATION CES-302 03/00 SUPERSEDES 02/99 PAGE 1 OF 9 CORROSION ENGINEERING SPECIFICATION FOR INSTALLATION CHEMICAL RESISTANT BRICK FLOORING USING THE BRICKLAYERS METHOD
More informationMEMBRANE WATER PROOFING. Our Services: Below ground waterproofing, Above-ground waterproofing, Wet Areas Waterproofing, Joint Sealants.
WATER PROOFING MEMBRANE s vast experience in providing constructive solutions to many famous building structures around the world hasbeen built on a broad portfolio of products. Our Services: Below ground
More informationPILGRIM PERMOCOAT, INC. 402 S.22nd Street, Tampa, FL (813) FAX# (813)
PILGRIM PERMOCOAT, INC. 402 S.22nd Street, Tampa, FL 33605 (813) 248-3328 FAX# (813) 248-1076 www.pilgrimpermocoat.com PILGRIM is a two-component,100% solid, high strength, low viscosity, epoxy resin adhesive.
More informationMega Clic Laminate Floor Installation Instructions
Mega Clic Laminate Floor Installation Instructions GENERAL Mega Clic is a revolutionary system for installing laminate floors without using glue. The planks can be clicked together simply, thanks to the
More informationTECHNICAL DATA SHEET SIKADUR 31 CF NORMAL 6KG
TECHNICAL DATA SHEET SIKADUR 31 CF NORMAL 6KG Sikadur 31 is a two component solvent-free, cold cure, thixotropic epoxy adhesive suitable for damp and dry substrates. Available in two grades - Normal and
More informationPre-applied waterproofing membranes that bond integrally to poured concrete for use below slabs or behind basement walls on confined sites
PREPRUFE 300R & 160R Pre-applied waterproofing membranes that bond integrally to poured concrete for use below slabs or behind basement walls on confined sites Product Description GCP Applied Technologies
More informationA. Texas Department of Transportation 2004 Standard Specifications for Construction and Maintenance of Highways, Streets and Bridges (TxDOT).
SECTION 32 13 14 CONCRETE PAVEMENT FOR VEHICULAR AREAS PART 1 GENERAL 1.1 SCOPE OF WORK A. This Section specifies the requirements for forming and placing reinforced concrete curbs and vehicular pavement
More informationConstruction. 1-part floor joint sealant. Product Description. Product Data. Tests. Form. Storage
Product Data Sheet Edition 19/09/2011 Identification no: 01 05 01 01 005 0 000001 Sikaflex Floor Sikaflex Floor 1-part floor joint sealant Product Description is a moisture curing 1-part elastic sealant
More informationE.V.A. EXPANSION JOINT SYSTEMS
E.V.A. EXPANSION JOINT SYSTEMS A PERMANENT, WATERTIGHT SYSTEM INTRODUCTION Thermal-Chem E.V.A. is an expanded, closedcell, cross-linked, pre-formed expansion joint system manufactured from ethylene vinyl
More informationSPECIAL SPECIFICATION 4897 Repair Structural Concrete
1993 Specifications CSJ 0331-04-045 SPECIAL SPECIFICATION 4897 Repair Structural Concrete 1. Description. This Item shall govern for the repair of delaminated, spalled and chipped areas of concrete foundations,
More informationA Design Review of Waterproofing Codes
A Design Review of Waterproofing Codes Section 1807 of Chapter 18 of the International Building Code addresses waterproofing under the section title of Dampproofing and Waterproofing. The section defines
More informationTechnical Data Sheet
Technical Data Sheet ProGUARD Concrete Insulated Sheathing Specifications & Installation Table Of Contents Product Description... pg. 1 Basic Use... pg. 1 Exterior Finishes... pg. 1 Standard Sizes... pg.
More informationInject-TITE AW All-Weather
Product Description Inject-TITE AW is a two-component styrene free, acrylic system used for anchoring and doweling applications in uncracked concrete using threaded rod and rebar. May be used in temperatures
More informationPOLYACRYLATE MODIFIED THINSET TERRAZZO 1
PART 1 - GENERAL GUIDE SPECIFICATION POLYACRYLATE MODIFIED THINSET TERRAZZO - REVISED AUG 02 1.1 RELATED DOCUMENTS A. Section includes thin set Polyacrylate Modified Terrazzo flooring (and integral cove
More informationLIFETIME WATERPROOFING SEALANT FREQUENTLY ASKED QUESTIONS
Welcome to the world's finest water sealant product. This page is designed to answer the most frequently asked questions about Lifetime Water Sealant 1). How many coats should I apply? One coat. Apply
More informationARDEX A 38 MIX Rapid Set, Premixed Screed
TM ARDEX A 38 MIX Rapid Set, Premixed Screed Fast-setting, premixed, easy-to-use and high-performance screed Note: The data herein applies to the ARDEX A 38 MIX 40 lb. (18 kg) bag which is pre-mixed with
More informationA. Submit product data sheets and literature verifying fire ratings and physical properties of materials.
I. GENERAL ACRYSHIELD ROOF MANAGEMENT SYSTEM Installation Guide Specification For Preserving BUR & Mod Bit Roofs 07560 Saving Money, Safeguarding the Environment One Roof at a Time. 1.01 SUMMARY A. Provide
More informationPRODUCT DATA SHEET. Product Description
PRODUCT DATA SHEET PREPRUFE 00R & 0R Pre-applied waterproofing membranes that bond integrally to poured concrete for use below slabs or behind basement walls on confined sites Product Description Preprufe
More informationSupaflow HF Grout. Dual Expansion Class C Grout. Description. Areas of application. Features
Supaflow HF Grout Dual Expansion Class C Grout Description Supaflow HF is a free flowing cement based grout offering high performance and non-shrink characteristics. This product is suitable for pumping
More informationCONCRETE Joint and Crack Sealing Basics
CONCRETE Joint and Crack Sealing Basics BACKGROUND Proper joint sealing contributes to good performance on roadways and airports. With proper design and construction, joint sealants minimize infiltration
More informationDist. by: BEST MATERIALS Ph:
Dist. by: BEST MATERIALS Ph: 800-474-7570 www.bestmaterials.com Email: Sales@BestMaterials.com NOVALINK SL SELF-LEVELING CONSTRUCTION SEALANT DIVISION 7 - THERMAL AND MOISTURE PROTECTION SECTION 07 92
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More informationSECTION MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Seal
SECTION 07550 MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Seal This section is based on the products of MFM Building Products Corp., which is located at: 525 Orange St. P. O. Box 340 Coshocton, OH 43812
More information1.02 RELATED WORK: Refer to the following sections for related work:
SECTION 4200 - CONCRETE STRUCTURES PART 1 - GENERAL 1.01 SCOPE: This Section covers installation of header curb, retaining walls, energy dissipation structures for drainage channels, reinforced concrete
More informationSection 710. WATERPROOFING AND PROTECTIVE COVERS
710.01 Section 710. WATERPROOFING AND PROTECTIVE COVERS 710.01. Description. This work consists of providing and placing membrane waterproofing and protective covers. 710.02. Materials. Provide materials
More informationPacific Polymers Elasto-Deck BT Guide Specification
1 07141-1 August 2016 Pacific Polymers Elasto-Deck BT Guide Specification SECTION 07141 FLUID APPLIED WATERPROOFING 2 07141-2 August 2016 Pacific Polymers Elasto-Deck BT Guide Specification SECTION 07141
More informationInstallation Manual. Foundations. Version 4.3ᵠ
Installation Manual Foundations Version 4.3ᵠ (*) - Denotes Current Revisions throughout this Installation Manual Version 4 (ᵠ) - Denotes Current Revisions for Version 4.3 of this Manual Manual updated
More informationGeneral Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions.
General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. Surface Preparation: Surface to be coated should be clean, dry and structurally sound.
More informationInstallation Guide. Rain Screen Panel System
Installation Guide Rain Screen Panel System Main Office 6860 South Abbott Road Orchard Park, New York 14127 tel 716.649.7490 toll free 1.888.214.3655 www.bostonvalley.com General Inquiries info@bostonvalley.com
More informationBid Opportunity Wilkes Reservoir North Cell Rehabilitation
Water and Waste MONOMER (EPDM) ROOFING Page 1 of 11 Part 1 General 1.1 REFERENCES.1 ASTM International Inc..1 ASTM D4637-14E1, Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane..2
More informationSECTION CONCRETE FORMWORK AND ACCESSORIES
SECTION 03100 CONCRETE FORMWORK AND ACCESSORIES Part 1 GENERAL 1.01 SUMMARY A. Furnish equipment, materials, and labor required for construction and removal of forms for the containment of concrete to
More informationPacific Polymers Elasto-Mat D&G Guide Specification
1 07141-1 August 2016 Pacific Polymers Elasto-Mat D&G Guide Specification SECTION 07141 FLUID APPLIED WATERPROOFING 2 07141-2 August 2016 Pacific Polymers Elasto-Mat D&G Guide Specification SECTION 07141
More informationPREPRUFE 300R LT & 160R LT
PREPRUFE 300R LT & 160R LT Pre-applied fully-bonded waterproofing membranes for low temperature applications Product Description GCP Applied Technologies ( GCP ) PREPRUFE Low Temperature Membranes (300R
More information1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.
WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3
More informationARDEX A 38TM Rapid Set Screed
ARDEX A 38TM Rapid Set Screed Fast-setting, easy-to-use, high-performance screed Note: The data herein applies to ARDEX A 38 50 lb. bag, not pre-mixed with sand. For ARDEX A 38 MIX 40 lb. bag that is premixed
More informationTECHSEAL POLYSULPHIDE SEALANT RDL 940 (Gun Grade) RDL 941 (Pour Grade)
TECHSEAL POLYSULPHIDE SEALANT RDL 940 (Gun Grade) RDL 941 (Pour Grade) DESCRIPTION TECHSEAL RDL 940/941 are two component sealant based on THIOKOL Polysulphide liquid elastomer. It consists of a Base compound
More informationInstallation Instructions
Warning: Do not remove outer shrink wrapping from the Fire Rated Foam stick until you have read and understand the FULL instructions for proper installation. Failure to follow these directions may degrade
More information