Jointofeu Series Fire Barriers I Installation Instructions
|
|
- Alaina Little
- 6 years ago
- Views:
Transcription
1 Product Description Jointofeu is manufactured from a woven mineral wool and installed into expansion joints with a heat resistant adhesive. It is suitable for both vertical and horizontal expansion joints with insulation and integrity requirements of up to 3 or 4 hours. Supplied coiled in sealed bags. Important Information Prior to the commencement of installation, all materials should be inspected for damage and any issues reported to Construction Specialties as soon as possible, so that replacement materials may be furnished without delay. All work must be completed as per drawings, and in accordance with these installation instructions. COSHH Regulations: Construction Specialties (UK) Limited comply with the statutory requirement for the Control of Substances Hazardous to Health (COSHH) Regulations MSD Sheets are available upon request. For more information visit: All dimensions in millimeters unless otherwise stated. Do not scale from the drawing. 01 of 06
2 Jointofeu-3 along joint Joint Width 20mm Horizontal Movement ±4mm Fire rating 3 Hr Roll Length Weight 20m 4.5kg 20 Jointofeu-3 for vertical or horizontal applications. 3hr rating Jointofeu-6 along joint Joint Width 40mm Horizontal ±8mm Fire rating 3 Hr Roll Length 20m Weight 11kg 40 Jointofeu-6 for vertical or horizontal applications. 3hr rating. Jointofeu-9 along joint Joint Width 60mm Horizontal ±12mm Fire rating 4 Hr Roll Length 18m Weight 36.5kg* *A lifting aid should be used to manoeuvre insulation. All dimensions in millimeters unless otherwise stated. Do not scale from the drawing. 60 Jointofeu-9 for vertical or horizontal applications. 4hr rating. 02 of 06
3 Typical application details with expansion joint covers Floor application including Jointofeu-3 and W90 cover plate W90 with small clip 20 Jointofeu-3 Wall application including Jointofeu-9 and FWS-200M Jointofeu-9 60 All dimensions in millimeters unless otherwise stated. Do not scale from the drawing. FWS-200M 03 of 06
4 Do Do use safety equipment Please refer to the relevant MSDS to ensure you are using the appropriate safety equipment to keep yourself and others out of harms way. Likewise remember to keep your working area clean and tidy as you progress. Do handle with care. Contact with the insulation will cause irritation. Please refer to the MSDS for appropriate protection. Do store material correctly Store the fire barrier insulation unopened in original packaging, in a cool and dry condition. The adhesive should be stored at a temperature between 5 o C and 25 o C and used before the expiry date found on the packaging. Do confirm the rope diameter It is imperative that the fire barrier selected is the correct size for the expansion joint opening on site and that the width is consistent along the length of the joint. Do Not Do not install in adverse temperatures The material must be installed when the substrate surface temperature is between 5 o C and 40 o C Do not rush the installation! All work must be completed as per these installation instructions. Installations that are not created as described cannot be assumed to create an effective fire barrier. 04 of 06
5 Tools / Equipment Below is a list of protective wear and tools that are likely to be required during this installation: Please also review the relevant MSDS to confirm that your PPE meets the required standards. Eye protection Cut resistant gloves Disposable gloves Dust masks Hard hat Safety boots Hi-Viz clothing Goggles Protective overalls Markers / Pencils Tape measure Ground sheets Utility knife Wood saw Masking tape Wire brush Palette Knife Paint / adhesive mixer Site vacuum cleaner Cleaning products Preparation Substrate The substrate must be strong, clean, dry, free from sharp protrusions, dust or any other contaminants that could prevent the adhesive from bonding correctly. Use masking tape and/or ground sheets to protect any area surrounding the expansion joint from excess adhesive. Just prior to installation, open the adhesive container and mix the adhesive until it is a consistent colour and texture. Material We recommend that you plan out where the fire barrier will be placed to allow sufficient extra material for splices or transitions. Jointofeu is supplied in rolls of 18 or 20m and each join and transition will require a 200mm overlap, this not only affects the quantity required, but the depth of the joint will also need to be sufficient to accept two sections of material where they will overlap. Jointofeu can be easily cut using a utility knife or saw. It can help to compress the section that requires cutting with a board. Installation Method Apply the adhesive supplied with the fire barrier to both sides of the joint using a palette knife at the following rates. Once applied, smooth over the adhesive to create a more consistent application. Model rate Coverage from 10kg container Model Gap Size Approximate insulation depth when installed Joinofeu-3 400g/lm 24m Joinofeu-3 20mm 40mm Joinofeu-6 400g/lm 24m Joinofeu-6 40mm 80mm Joinofeu-9 800g/lm 12m Joinofeu-9 60mm 140mm Compress the Jointofeu Fire Barrier and push into the expansion joint, positioning at the desired level using a appropriate sized piece of wood if required. If an expansion joint cover is to also be installed, the Jointofeu must be positioned so that they do not come into contact. Additionally, no other products can be allowed to interfere/pass through the Jointofeu e.g. drainage pipes. Note: The adhesive will require a minimum of 48 hours to fully cure at 20 o C. 05 of 06
6 Transitions / Splice The junction is made by using a small amount of adhesive (Approx. 30g) to join two overlapping lengths of fire barrier insulation. The overlap needs to be a minimum of 200mm so that the direction of fire would need to pass two lengths of insulation. Standard join 200 Direction of fire Floor to Wall T Section 200 Direction of fire Floor to Floor T Section 200 A A A - A Direction of fire 06 of 06
RAUPEX SPEED SYSTEM Installation Guide
RAUPEX SPEED SYSTEM Installation Guide INFORMATION AND SAFETY INSTRUCTIONS Validity The installation instructions are valid for North America. Other applicable technical information - Floor heating/cooling
More informationPart of the Sikaplan WT Membrane System
System Product Data Sheet Edition: 10.2011 Identification no: 02 07 03 02 System Sikaplan WT Tape 200 System Part of the Sikaplan WT Membrane System Product Description Sikaplan WT Tape 200 is a high performance
More informationMETHOD STATEMENT SCREEDING OF FLOOR
17-18 Gaerwen Industrial Estate Gaerwen Isle of Anglesey LL60-6HR Tel: 01248-422555 Fax: 01248-422556 Mobile: 07891-557581 Project/Contract Preparation of sub floors & screeding principal Contractor Apollo
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationSILASEC DESCRIPTION FEATURES AND BENEFITS SURFACE PREPARATION
SILASEC WP0001 REVISED: JANUARY 2002 DESCRIPTION Bondall Silasec is a concentrated liquid waterproofing compound designed to be used with Portland type A or type GP cements to form a permanent waterproof
More informationInstallation Guidance Note: Flotex Sheet
General Advice The appearance, performance and durability of the installed floorcovering will be determined to a large extent by the quality of the prepared subfloor and the conditions in which they are
More informationGENERAL SHALE NATURAL THIN ROCK VENEER Installation Guide. GeneralShale.com
GENERAL SHALE NATURAL THIN ROCK VENEER Installation Guide GeneralShale.com GENERAL SHALE NATURAL THIN ROCK VENEER Page 2 INTRODUCTION - TABLE OF CONTENTS Check local building codes for proper installation
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. RobinsonBrick.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide RobinsonBrick.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More informationFAST SETTING and FAST CURING MORTAR NATCEM 35
NATURAL CEMENT DISTRIBUTION LTD INSTRUCTION FOR USE FAST SETTING and FAST CURING MORTAR NATCEM 35 ISSUE 1 23 June 2017 Page 1 of 10 INSTRUCTIONS FOR USE NATCEM 35 -FAST SETTING and FAST CURING MORTAR This
More informationSEMPEO SQA Unit Code FP3G 04 Forming and assembling electrical cable enclosure and support systems
Forming and assembling electrical cable enclosure and support Overview This standard covers a broad range of basic competences that you need to form and assemble electrical cable enclosure and support
More informationHYDRAULIC GATE SEALS. Industrial Rubber Supply (1995) Ltd.
Industrial Rubber Supply (1995) Ltd. Manufacturers of Quality Industrial Products 55 Dunlop Avenue, Winnipeg, Manitoba, Canada R2X 2V2 Phone (204) 694-4444 - Fax (204) 632-6767 - www.indrub.com ISO 9001:2000
More informationPAYING ATTENTION TO DETAIL by Bob Cusumano
PAYING ATTENTION TO DETAIL by Bob Cusumano Painting contractors are often required to install caulk or sealant in exterior joints. Too often, the sealant is simply gunned into the joint until it s filled
More informationSafe Work Method Statement
Safe Work Method Statement Disclaimer: Use of Master Builders Generic Safe Work Method Statements The Master Builders Association of Victoria expressly disclaim all and any liability to any person in respect
More informationConstruction. Tricosal Waterstops - Tricomer. Waterstops for joint sealing in watertight concrete construction according to DIN and DIN
Construction Product Data Sheet Edition 19 April 2013 Tricosal Waterstops - Tricomer Waterstops for joint sealing in watertight concrete construction according to DIN 18541 and DIN 18541-2 Product Description
More informationNURAPLY 3PT TECHNICAL DATA SHEET
NURAPLY 3PT Waterproofing membrane consisting of straight run bitumen heavily modified with polymers (APP = Atactic Polypropylene) and reinforced with a non-woven polyester. FINISHING Top surfaced finished
More informationStop and Read Before Installing Material
Premium Dry Erase Materials Installation procedures for full wall application with woven and nonwoven backed products Stop and Read Before Installing Material Installation Procedures EXAMINATION Jot.a.wall
More informationINSTALLATION MANUAL. METAL INSULATED PANELS -ROXUL -Expanded Polystyrene
INSTALLATION MANUAL METAL INSULATED PANELS -ROXUL -Expanded Polystyrene Insulated Metal Panels London Eco-Metal Manufacturing Inc. **Also see Eco-Metal s Handling Manual** These instructions are provided
More informationSAFETY DATA SHEET. Blanket D-24B
Blanket D-24B Page 1 of 7 SAFETY DATA SHEET Blanket D-24B SDS according to Regulation (EC) No. 1907/2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH), Annex
More informationAsbestos in Your Home
Asbestos in Your Home Your guide on where it may be used and what to do if it s in your home the facts Sandbourne Housing Association Registered Office: Beech House, 28-30 Wimborne Road, Poole, BH15 2BU
More informationCaparol System PRO Data sheet
System features Expanded polystyrene insulation Cost effective solution Excellent detailing options Proven technology Wide variety of colours Reliable protection and crack resistance Proven track record
More informationTUFF-TAC TM BRIDGE MEMBRANE INSTALLATION GUIDE
5 pages TUFF-TAC TM BRIDGE MEMBRANE INSTALLATION GUIDE The following will describe the proper procedure to use when installing Tuff-Tac TM bridge deck membrane. The guide will cover recommended tools to
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and
More informationSECTION JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 07-9200 - JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationPPC Cement TUTORIAL. how to screed a floor
PPC Cement TUTORIAL how to screed a floor Pre-build: TOOLs & Materials ITEM Quantity Check. Builders bucket. Wheelbarrow 3. Shovel 4. Builder s line 5. 50mm steel pegs 6. Rigid timber forms 7. Flexible
More informationQuietRock 530 RF Application Notes
QuietRock 530 RF Application Notes Installation instructions for QuietRock RF and QuietSeam RF in construction of high security environments such as Sensitive Compartmented Information Facilities (SCIF)
More informationINSTALLATION INSTRUCTIONS
1 of 6 INSTALLATION INSTRUCTIONS IMPORTANT! Store the floorboards at room temperature for at least 48 hours, still in their packaging, prior to commencing installation. Ideal room temperature is 18-22
More informationRev. 07 8/15 Please Read Disclaimers:
FiberCorr panels Guidelines 6005.FC Rev. 07 8/15 Please Read Disclaimers: PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION!! These guidelines are provided in good faith to help prevent any problems
More informationGyproc Cove and Cornice
ove and ornice Introduction Overview ove and ornice are comprised of a gypsum plaster core encased in a white or ivory paper liner. The cove and cornice range is one of the easiest ways to enhance the
More informationSignature Sports Flooring Installation Instructions. For SignaDeck Premium Rubber Tiles
Signature Sports Flooring Installation Instructions For SignaDeck Premium Rubber Tiles These instructions supersede any verbal or written instructions from Signature Sports Flooring representatives and
More informationSika KAB combination joint waterbars waterstopping systems
PRODUCT DATA SHEET Sika KAB combination joint waterbars Waterbars for waterproofing construction and crack induced shrinkage joints in new reinforced concrete structures PRODUCT- DESCRIPTION KAB 125/KAB
More informationINTRODUCTION TO THE PROGRAM
INTRODUCTION TO THE PROGRAM Structure and Organization Information in this program is presented in a definite order, so that employees will see the relationships between the various groups of information
More informationPLATON FOUNDATION WRAP
DRAINAGE SOLUTIONS SINCE 1908 PLATON FOUNDATION WRAP RUGGED, DIMPLED HIGH-DENSITY POLYETHYLENE (HDPE) MEMBRANE THAT KEEPS FOUNDATIONS DRY ADVANCED TECHNOLOGY EASY INSTALLATION PROVEN PERFORMANCE ARMTEC.COM
More informationENGINEERED LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING
ENGINEERED LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to
More informationTILE TILE
09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements
More informationPANELITE. Bonded Series Fabrication Guide
PANELITE Bonded Series Fabrication Guide www.panelite.us (c) Panelite 2012 PANELITE Bonded Series Handling and Storage General The plastic film protects panel surfaces. Keep the protective film in place
More informationSTEP UP SHOWER BASE INSTALLATION GUIDE FOR TIMBER AND CONCRETE FLOORS
GUIDE FOR TIMBER AND CONCRETE FLOORS EDITION: APRIL 2016 IMPORTANT: This guide is for the installation of a Step Up shower base on a timber or concrete floor. If you require a walk in (flush with floor)
More information84 Lapping & Jointing 86 Service Pipe Penetrations 87 Sealing to Cavity Wall Constructions 88 Protecting Membranes System Components.
84 Lapping & Jointing 86 Service Pipe Penetrations 87 Sealing to Cavity Wall Constructions 88 Protecting Membranes 90 System Components installation/ SYSTEM COMPONENTS INSTALLATION ADVICE LAPPING and JOINTING
More informationCrystoflex Max comprising of a liquid component of selected polymers and a powder component of selected cements, fillers and aggregates.
Product Data Sheet Crystoflex Max Two pack, flexible, cementitious waterproofing membrane for positive or negative water pressure. Description Crystoflex Max is a two pack, flexible, cementitious waterproof
More informationMarine Fire Wrap General Installation Instructions Cable Penetrations through A0-A60 and B0-B30 Bulkheads and Decks
Marine Fire Wrap General Installation Instructions Cable Penetrations through A0-A60 and B0-B0 Bulkheads and Decks Reference(s) MED 1050201, EC Type Examination Module B (Lloyd s Register, LR) F-20427
More informationAcetone is flammable; refer to the manufacturer s instructions for complete safety information.
Installing UPP FRP Entry Seals on Fiberglass Sumps Introduction This document is meant as an installation overview for UPP FRP entry seals with fiberglass sumps and should be used in conjunction with the
More informationASBESTOS YOUR QUICK GUIDE DON T BE AN EASY TARGET
EP IDE KE GU IS TH ASBESTOS YOUR QUICK GUIDE DON T BE AN EASY TARGET Asbestos could be in the house or building you are working on right now. Left alone, it isn t dangerous. However, once disturbed, tiny
More informationConstruction. Sikadur 31, Hi-Mod Gel. Application Instructions. Sika Corporation
1 Sikadur 31, Hi-Mod Gel Application Instructions Sikadur 31, Hi-Mod Gel Structural epoxy paste adhesive Two-component 100% solids Solvent-free Moisture-tolerant High-strength High-modulus Sikadur 31,
More informationWORKING SMART WITH FIBER GLASS, ROCK WOOL AND SLAG WOOL PRODUCTS
WORKING SMART WITH FIBER GLASS, ROCK WOOL AND SLAG WOOL PRODUCTS Recommended Work Practices for the Installation of Synthetic Vitreous Fibers (SVF) HEALTH & SAFETY PARTNERS The manufacture and use of fiber
More informationSECTION mil thickness COLD FLUID-APPLIED WATERPROOFING
SECTION 07 14 16 CCW-MIRASEAL @ 120 mil thickness COLD FLUID-APPLIED WATERPROOFING PART 1 - GENERAL 1.1 SECTION INCLUDES: Installation of waterproofing membrane on surfaces indicated on drawings, consisting
More informationPlastering. Holiday Inn - Sultanate of Oman
1 208 Holiday Inn - Sultanate of Oman Gyproc GypFine Plasters provide the ultimate skimming solutions for today s high-end finish. They are formulated to suit a wide variety of backgrounds including plasterboard,
More informationPlanning and installation instructions
Planning and installation instructions Stofix Oy Ahlmaninkatu 2 E 40100 Jyväskylä Finland stofixgroup@stofix.com www.stofix.com 2 PLANNING AND INSTALLATION INSTRUCTIONS... 1 1 General... 3 2 Project Design...
More informationProduct Data Sheet A Guide for the Installation, Maintenance & Repair of Standard Glass Reinforced Gypsum Components
Product Data Sheet A Guide for the Installation, Maintenance & Repair of Standard Glass Reinforced Gypsum Components 1 Table of Contents GENERAL PRODUCT INFORMATION.....3 Uses... 3 Typical Composition.......3
More informationFiberFloor Glueless and Full Spread Installation Instructions
TECHNICAL SERVICE FiberFloor Glueless and Full Spread Installation Instructions September 22, 2016 PRODUCTS All Tarkett Fiberglass reinforced material for residential application INSTALLATION SYSTEMS Glueless
More informationVESDURA VINYL PLANKS 7.5MM WPC CLICK LOCK - AMERICANA COLLECTION
VESDURA VINYL PLANKS 7.5MM WPC CLICK LOCK - AMERICANA COLLECTION Before You Start Click lock vinyl plank flooring is normally laid without adhesive. Before installation, planks must be allowed to acclimatize
More informationRainBarrier Installation Guide
Installation Guide Installation Instructions for: > / Impasse Hanger Attachment > / Attachment > Brick Tie/Masonry Anchor Installation > Installation within -Type Framing > Installation Installation Guide
More informationMagnetic Dry Erase Chalk Image Projection Paintable Custom
Magnetic Chalk Image Projection Paintable Custom Magnetic & Product Reference Key Benefits: Feature a thin sheet of iron (ferrous, magnetic metal) in the HPL backer. Makes these more magnetic than powdered
More informationHILTI CP 674 Cavity Closure For Rainscreen / Cladding Systems
Data Sheet HILTI CP 674 Cavity Closure For Rainscreen / Cladding Systems The enclosed pages are taken from the Hilti Firestop Systems Manual Edition April 2011 Supported by additional standard details
More informationINSTALLATION MANUAL PIPE SUPPORT
INSTALLATION MANUAL PIPE SUPPORT Clock Spring Company L.P. 621 Lockhaven Dr. Houston, Texas, 77073 Phone: 281-590-8491, 800-471-0060 Fax. 281-590-9528 http://www.clockspring.com 1 Full Snap Wrap Kit Installation
More informationSAFETY DATA SHEET Universalskiva 1201
Universalskiva 1201 Page 1 of 7 SAFETY DATA SHEET Universalskiva 1201 SDS according to Regulation (EC) No. 1907/2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals
More informationMapefix PE Wall. Chemical anchor for masonry and light loads
Mapefix PE Wall Chemical anchor for masonry and light loads European Technical Approval ETAG 029 M8 M12 AREAS OF USE Mapefix PE Wall is an adhesive for chemically anchoring metal bars in holes made in
More informationProduct Information CHEMGLAZE B 9942 A/B. Coating for Casting Pits. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces.
Product Information Chemical Products Division CHEMGLAZE B 9942 A/B Coating for Casting Pits. FEATURES BENEFITS. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces. Will build to
More informationTHERMOFIT ADHESIVE S Flex Fluid Resistant, High Temperature, One Part-Flexible Epoxy
TE Connectivity 30 Constitution Drive Menlo Park, CA 9402 USA SPECIFICATION THIS ISSUE: DATE: REPLACES: RT-1014 ISSUE 4 April 19, 2016 Issue 3 1. SCOPE THERMOFIT ADHESIVE S-12-04 Flex Fluid Resistant,
More informationSafety use instruction sheet
Safety use instruction sheet 1. Company and product identification 1.1 Product: ISOVER rolls, slabs and board products of bio-soluble glass fibres, for industrial application 1.2 Field of application:
More informationSEPTEMBER construction type cavity barriers. SP Firestop Systems. The purpose-made solution for cavity fire stopping
SP Firestop Systems The purpose-made solution for cavity fire stopping SP Firestop Systems The purpose-made solution for cavity fire stopping As part of the comprehensive FIREPRO range of fire protection
More informationRMF Intercell. NBS Specification 2013 K41
RMF Intercell NBS Specification 2013 K41 InterfaceFLOR BV. K41 Specification 40mm, 60mm, 80mm, 90mm and 110mm K41 Raised access floors To be read with Preliminaries/ General conditions. TYPES OF RAISED
More informationDynamic Bonding Systems B.V. A division of Dutch Bonding Group B.V.
for the bonding of facade cladding with KOMO-certified bonding system Dynamic Bond METALS - HPL - FIBRECEMENT Dynamic Bond For panels up to the maximum diagonal. Based on MS-hybrid-polymers, one component.
More informationAsbestos Awareness Program
Safety Manual 1 of 9 Safety Manual Sect: 1.0 Purpose 2.0 Scope Rel. Date: Last Review: This program covers Ardent policy related to asbestos, either discovered or suspected in the workplace. Ardent recognizes
More informationOVERKOTE E-100 Epoxy Floor Coating Technical Data
OVERKOTE E-100 Epoxy Floor Coating Technical Data PRODUCT DESCRIPTION OVERKOTE E-100 is a floor coating system applied at a thickness of 16 to 50 mils. It is designed for long term protection of concrete
More informationSELECT SURFACES LAMINATE FLOORING INSTALLATION GUIDE DRIFTWOOD
TOOLS AND MATERIALS SELECT SURFACES LAMINATE FLOORING INSTALLATION GUIDE DRIFTWOOD Vapor barrier (minimum 6 mil/0.15 mm) (if needed) Transitional moldings (if needed) Measuring tape Carpenter s square
More informationAESTUVER fire-protection mastic For the AESTUVER expansion joint M
fermacell AESTUVER product data sheet For the AESTUVER expansion joint M Product is an elastic RTV-1 silicone combined with halogen-free fire retardants. Silicone is a versatile elastomer which is mainly
More informationSpeedlock Pallet Racking
Assembly specification These instructions are to assemble Dexion Speedlock Pallet Racking which conforms with the specifications below. Frame heights not more than 4800mm Frame depths 840mm Not less than
More informationPITCHED ROOF SOLUTIONS
PITCHED ROOF SOLUTIONS, airtightness and moisture management solutions for pitched roof rafter applications. isover.co.uk Pitched Roof Solutions Building extra living space within the attic is a great
More informationSIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE. Product. Scope. Appraisal No. 811 [2013] Appraisal No. 811 (2013) Amended 28 August 2017
SIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE Amended 28 August 2017 BRANZ Appraisals Technical Assessments of products for building and construction. Sika (NZ) Ltd PO Box 19 192 Avondale Auckland 1746
More informationR10 RAINWATER DRAINAGE SYSTEMS
R10 RAINWATER DRAINAGE SYSTEMS To be read with Preliminaries/General conditions. GENERAL INFORMATION/REQUIREMENTS 110 GRAVITY RAINWATER DRAINAGE SYSTEM - Rainwater outlets: Proprietary (see clause 365)
More informationHYBRID. Pre-Laying Checks
Warning Veles CK has been developed for exceptional stability in low and high temperatures, however, after installation extreme temperatures (under 5 C or over 50 C) should be avoided by use of interior
More informationSYNTHETIC GRASS INSTALLATION GUIDE SOFT AND HARD SURFACE
SYNTHETIC GRASS INSTALLATION GUIDE SOFT AND HARD SURFACE HARD SURFACE INSTALLATION You will need: Tape measure Rope or spray paint Weed spray Sharp utility knife and spare blades Synthetic grass adhesive
More informationInstallation Procedure of Floating floors
SUBFLOOR PREPARATION OF WICANDERS FLOATING FLOORS WITH CORKLOC Wicanders floating floors with Corkloc can be installed in most domestic areas and in almost all commercial areas except in bathrooms, saunas
More informationSPECIFICATION DIVISION 7 NUMBER SECTION DESCRIPTION DIVISION 07 THERMAL AND MOISTURE PROTECTION SECTION THROUGH-PENETRATION FIRESTOP SYSTEMS
BuildingName The Description of the Project P00000000 0000 DOCUMENTS Title Page Table of Contents Instruction to Bidders Form of Proposal Equal Opportunity Statement Form of Guarantee Supplemental General
More informationL'ISOLANTE K-FLEX. LNG applications Manual
L'ISOLANTE K-FLEX LNG applications Manual LNG applications Manual The insulation LNG plants may forsee a multilayer design according to the specific characteristics and the working temperatures of the
More informationARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE
ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box
More informationSLAB ON GRADE Insul-Joint or Expansion Joint Material as Required by A/E Specifications AquaCheck Liquid Coating 400 (Waterproofing Membrane) with Aqu
INSTALLATION INSTRUCTIONS Note: The following installation instructions are based off of ASTM E 1643 (Standard Practice for Installation of Water Vapor Retarders Used in Contact with Earth or Granular
More informationBEAM & BLOCK SYSTEM. 108mm. 175mm Deep (160mm) Wide Beam. 160mm
RH F RACKHAM HOUSEFLOORS BEAM & BLOCK SYSTEM BEAM & BLOCK SYSTEM 1. THE BEAMS 60mm 108mm 90mm 75mm 75mm 100mm 175mm 100mm 175mm 125mm 100mm 175mm Deep Beam 175mm Deep (160mm) Wide Beam 225mm Deep Beam
More informationConstruction. S-Vap 5000E SA Self-adhesive Vapour Barrier. Product Description
Roofing Product Data Sheet Edition 11.2014 / xtra UK Identification no. 02 09 45 05 100 0 000019 Version no. 03 S-Vap 5000E SA Self-adhesive Vapour Barrier Product Description S-Vap 5000E SA is a multi-layer
More informationBOLON BY YOU INSTALLATION INSTRUCTIONS ROLLS
1 (5) THE MATERIAL The material is a woven vinyl product backed with glassfibre-reinforced vinyl. Since the material is a woven product, its structure is naturally irregular. The material is not approved
More informationRIW SHEETSEAL GR BENEFITS APPLICATIONS APPLIED TO
CI/SfB TN6 LI4143 August 2017 RIW SHEETSEAL GR is a cold applied, high density polyethylene film bonded to aluminium foil and coated with a bitumen/rubber self adhesive layer with a removable reinforced
More informationCOMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION
COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN INSTALLATION! IMPROPER INSTALLATION WILL VOID WARRANTY. STOP! WPC Engineered Vinyl Flooring
More informationInstallation instructions Thin, flexible multi-foil insulation
The original BBA certified multi-foil Installation instructions Thin, flexible multi-foil insulation Below rafter 0.18 solutions Below 100 rafter + 70 foiled 70 foiled 165.5 spacer batten min 10 38 batten
More informationAsbestos in the Home
Asbestos in the Home This document will help you understand asbestos: what it is, its health effects, where it is in your home, and what to do about it. What Is Asbestos? Asbestos is a mineral fiber. It
More informationHygienic cladding solutions. the complete internal cladding solution
Hygienic cladding solutions the complete internal cladding solution Hygienic cladding range overview Our range of sheets, prof iles and adhesives are made to industry leading standards to meet all customer
More informationCONDUITS AND FITTINGS
CONDUIT AND FITTINGS Rigid Steel Conduit 3801 Rigid PVC Conduit 3803 HDPE Conduit 3803 Flexible Non Metallic Liquid Tight Conduit Type LFNC-B 3804 PVC Coated Urethane Lined Galvanized Rigid Steel Conduit
More informationINSTALLATION GUIDANCE. Easy to Install, Clean and Maintain NO GROUT! Perfect for Showers!
INSTALLATION GUIDANCE Easy to Install, Clean and Maintain NO GROUT! Perfect for Showers! GENERAL INSTALLATION GUIDANCE Panels should be checked for any damages, imperfections, colour tone differences or
More informationFloor Insulation Underlayment Section Sound Control Matting
Floor Insulation Underlayment Section 09618 Sound Control Matting Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in excess of 50 to meet building
More informationSteps in Building a Shed
Steps in Building a Shed The design and location of your new shed will depend on how it will be used - a shed for storing tools will be much simpler than one you intend to use as a small shop. For example,
More informationCONCRETE STEPS, HANDRAILS, AND SAFETY RAIL
SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES
More informationASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED TYPE. Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION
[ TECHNICAL BULLETIN ] ASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED Sumolac PRODUCT TYPE Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION Astec Sumolac is a
More informationAmpreg F230-1 FOAMING EPOXY SYSTEM
Provisional datasheet Ampreg F230-1 FOAMING EPOXY SYSTEM Expanding Epoxy System Density 150 300kg/m 3 Uses Ampreg 21 hardeners Good mechanical and thermal properties Excellent adhesion to substrates Three
More informationARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound
ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE
More informationTechnical Data Sheet StoLevell Duo plus
Mineral bonding and reinforcing mortar Characteristics Areas of application Properties Exterior and interior For all mineral substrates For bonding insulation boards onto mineral substrates For producing
More informationEcore Athletic Elevate BOUNCE 2 GUIDE SPECIFICATIONS Ecore
October 31st, 2016-This document is provided solely as a convenience for spec writers in the drafting process. Ecore will not be held responsible for the use or alteration of any information contained
More informationPRODUCT SPECIFICATIONS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below
More informationGigaCrete Specification PlasterMax. PlasterMax : Fire Rated Plaster for Direct Application over Cement Masonry Units (CMU) Interior Walls
GigaCrete Inc. 6775 Speedway Blvd. Suite M105 Las Vegas, NV 89115 Ph (702) 643-6363 Fax (702) 643 1453 www.gigacrete.com GigaCrete Specification PlasterMax PlasterMax : Fire Rated Plaster for Direct Application
More informationENKASONIC FLOOR UNDERLAYMENT 9110
ENKASONIC FLOOR UNDERLAYMENT 9110 GS1197 Section 13080 SECTION 09618 SOUND CONTROL MATTING Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in
More informationAUGUST 2017 HASTINGS. retaining walls installation guide
AUGUST 2017 HASTINGS retaining walls installation guide RETAINING WALL INSTALLATION GUIDE RETAINING WALL information Austral Masonry retaining wall blocks are an ideal choice for retaining walls in gardens,
More informationInsulation Board. Knauf Data Sheet PE-DS
Insulation Board Knauf Data Sheet PE-DS-2 12-06 Insulation Board Description Knauf Insulation Board is a thermal and acoustical insulation product made from inorganic glass fibers preformed into boards
More information