3M Pak Wall Header

Transcription

1 M Pak Wall Header Latch/Ejector, Straight and Right ngle, High Temp Option 000 Series S Military (with M s 518 polarizing key) and centerbump polarization S Optional ejector latches S Mounting holes for securing header to board S Solder tail and wrap tail options S Optional polarizing posts S High temperature option Date Modified:May 0, 200 TS Sheet 1 of 4 Physical Insulation Material: Glass Filled Polyester (PT) Glass Filled Polyester (PCT High Temp Option) Flammability: UL 94V-0 Color: Gray, Standard eige (High Temp Option) Contact Material: Copper lloy Plating Underplate: 100 µ [2.54µm ] Nickel QQ-N-290, Class 2 Wiping rea: Gold MIL-G-45204, Type II, Grade C Solder Tails: 200 µ [5.08µm ] 60/40 Tin Lead MIL-P Wrap Tails: Gold Flash, Standard Marking: M Logo, Part Identification Number and Orientation Triangle Electrical Current Rating: 1 Insulation Resistance: > Ω at 500 Vdc Withstanding Voltage: 1000 Vrms at Sea Level Environmental Temperature Rating: - 55 C to +105 C High Temp Process Rating: Maximum 25 C, with 90 seconds over 215 C UL File No.: E M is a trademark of M Company

2 M Pak Wall Header Latch/Ejector, Straight and Right ngle, High Temp Option 000 Series -X0XX No Ejector/Latch -X5XX Short Ejector/Latch for M Sockets without Strain Relief -X6XX Long Ejector/Latch for M Sockets with Strain Relief -X4XX Ejector only.08 [2.0].424 ±.010 [ ].97 Ref [24.6].08 [2.0].57 ±.010 [ ] 1.07 Ref [27.2] 1.07 Ref [27.2].7 Ref [9.4].46 Ref [11.7].42 Ref [10.7] Note: This Ejector is a Nickel Plated Zinc lloy Casting..025 ±.002 Sq Typ [0.64] 2X « [6.1].020 [0.51] D.28 [7.1].0 [7.6].25 [6.4] Section -- (Straight) FTyp E ± ±.002 Sq Typ [0.64].12 [.0] Orientation Triangle.21 [5.] Notch (See Table 1 & Note1).16 [4.1] Notch Notch C (See Table 1 & Note 1).4 [8.] FTyp.24 [6.1].0 [7.6].68 [17.].5 [8.9].12 [.0] E ± Ref [1.24] Section -- (Right ngle).020 [0.51] 2X «.100 C.197 [5.00].20 [5.1] TS Sheet 2 of 4 M is a trademark of M Company

3 M Pak Wall Header Latch/Ejector, Straight and Right ngle, High Temp Option 000 Series Table 1 Pin M Part Dimensions Polarization Quantity Number C D Notches Provided [2.1] [28.07].865 [21.97].71 [18.0] C [7.2] 1.05 [.15] [27.05].91 [2.1] C [9.7] [5.69] [29.59] 1.01 [25.6] C [44.8] [40.77] 1.65 [4.67] 1.21 [0.7] C [49.8] [45.85] [9.75] 1.41 [5.8] C [52.4] [48.9] [42.29] 1.51 [8.] C [57.4] [5.47] [47.7] ] C [62.6] 2.05 [58.55] [52.45] 1.91 [48.5] C [70.2] [66.17] 2.65 [60.07] 2.21 [56.1] C [82.9].105 [78.87] [72.77] 2.71 [68.8] C [95.6].605 [91.57].65 [85.47].21 [81.5] C [100.7].805 [96.65].565 [90.55].41 [86.6] C Table 2 M Part Number Suffix Contact t Tail Dimensioni E Pin Cross Section Dimension F Diagonals Corner Radii Dimensioni G -5XX2-6XX2 Solder Tail for.062 [1.57] Thick PC oard.112 [2.84] ±.0005 [0.622] ±.001 [0.71] Ref [0.191].05 ±.00 [0.89] (See Note ) -5X0-6X0 Solder Tail for.094 [2.9] to.125 [.18] Thick PC oard.155 [.94] ±.0005 [0.622] ±.001 [0.71] Ref [0.191].05 ±.00 [0.89] -5X05-6X05 Wire Wrap Tail for up to Levels of Wire Wrap.61 Ref [15.5] ±.002 [0.65] 0.05 ±.00 [0.90] 0.00 Max [0.08].045 ±.00 [1.14].00 [7.62] Side to Side Stackability or «.116 [2.95] «.106 [2.69] GDia «.106 [2.69].41 [10.4] Max to Edge of PC for Daisy Chain or «.116 [2.95] GDia Y.060 [1.52].100 ± ± [8.94].029 [0.74].100 ± ± [5.89] C Recommended Mounting Hole Pattern (Straight) Notes: 1. Notches & C will accomodate M Polarizing Keys (M Part #N518). 2. ccepts Rear and Front mounting hardware: Rear Entry: #4-24 thread cutting screw, M Part #41-5,.116 [2.95] dia mounting hole Front Entry: (Prior to installation of latch on Straight Versions) #2-56 bolt and nut, M Part #41-6,.106 [2.69] dia mounting hole. The recommended PC hole size for the kinked tail positions on the.112 solder tail connector is.05 ±.002. Refer to TS-0972 for the positions kinked. Recommended Mounting Hole Pattern (Right ngle) Inch [mm] Tolerance Unless Noted Inch ±.1 ±.01 ±.005 [ ] Dimensions for Reference only TS Sheet of 4 M is a trademark of M Company

4 M Pak Wall Header Latch/Ejector, Straight and Right ngle, High Temp Option 000 Series Ordering Information Product Material: N= HighTemp lank = Standard M Part Number 0 Microinches Gold Plated Product Shroud and Pin Configuration 5 = 4 Wall, Right ngle 6=4Wall,Straight XXXXX-XXXX Latch/Ejector System 0 = No Latch/Ejector 4=RollPinEjectors (M Part # 505-4) 5 = Short, Snap-In Latch/Ejectors, (M Part # 505-0) 6 = Long, Snap-In Latch/Ejectors (M Part # 505-1) Tail 02 = Solder Tail for.062 [1.57] Thick oard K2 = Kinked Solder Tails for.062 [1.57] Thick oard 0 = Solder Tails for.094 to.125 [2.9 to.18] Thick oard 05=WrapPostsforuptolevelsofWireWrap (Not available on High Temp version.) 15 Microinches Gold Plated Product Product Material: N= HighTemp lank = Standard XXXXX-XXXXUG Plating Suffix UG = 15 microinch Gold M Part Number Shroud and Pin Configuration 5 = 4 Wall, Right ngle 6=4Wall,Straight Tail 02 =Solder Tail for.062 [1.57] Thick oard K2=Kinked Solder Tails for.062 [1.57] Thick oard 0 =Solder Tails for.094 to.125 [2.9 to.18] Thick oard Latch/Ejector System 0 = No Latch/Ejector 5 = Short, Snap In Latch/Ejectors (M Part #505-0) 6 = Long, Snap In Latch/Ejectors (M Part #505-1) TS Sheet 4 of 4 M is a trademark of M Company

5 Important Notice ll statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. efore using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. ny statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 1 year from the date of purchase. M MKES NO OTHER WRRNTIES INCLUDING, UT NOT LIMITED TO, NY IMPLIED WRRNTY OF MERCHNTILITY OR FITNESS FOR PRTICULR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any loss or damage arising from this M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted. Electronic and Division 6801 River Place lvd. ustin, TX M 200