CONSISTENCY FOR HIGH QUALITY IS OUR ROAD MAP
|
|
- Christian Logan
- 5 years ago
- Views:
Transcription
1 ADVANTAGES OF OUR INVESTMENT CASTING TECHNIQUE; High surface finishes quality (Ra ) Close linear tolerances (DIN VDG P690) Near net shape Cevik Technical Metallurgy was founded in 2011 in Tuzla-Istanbul, Turkey. With 25 years of experience and 1,500 square metres production area -fully equipped with the latest investment casting technology and infrastructure, we are already recognised as one of the main players of Investment Casting Industry in Turkey. Our Ceramic Mould Investment Casting Method (Low Wax Investment Casting) gives completely different advantages comparing to traditional Casting Methods; close linear tolerances, high surface quality, near net shape for complex parts, wide range of alloy selection for better performance İOur mission is not only limited with casting but to be a solution partner for your design and for the selection of the most efficient production method and alloy type. Flexibility in Weight: end products from 1gr to 40 kgs Flexibility in Alloy Selection Ferrous alloys: all kinds of steels Non-ferrous alloys: copper based, aluminium based, nickel based, cobalt based Flexibility in Design: Almost any kind of complex geometry which are difficult in traditional casting methods Thicknesses down to 0,5mm One part casting, no split lines Freedom in internal geometries Flexibity in Quantities Cost effective method even for low quantities Consistency and Standardisation in High Quality CONSISTENCY FOR HIGH QUALITY IS OUR ROAD MAP We believe that Consistent Quality is never an accident; it is always the result of high intention, sincere efforts, intelligent direction and skillfulexecution. In this sense, we steer our quality control to raw materials and production method parameters rather than the quality control of end product itself. Additionaly, we can check end product by means of different destructive and non-destructive testing techniques. Low Tool Cost Best Material Characteristics Microstructure with fine grains. High material charesteristics due to low porosity, inclusions and segregations Weight reduction by means of design and best material characteristics.
2 INVESTMENT CASTINGS COST ADVANTAGES Provides near net shape lowers material usage Reduces material costs Reduces expensive machining operations Eliminates expensive production and welding costs Low initial mold and tooling costs Economic order quantities: both for prototype quantities and mass production quantities MARKETS WE SERVE Aerospace Industry Automotive and Railway Industry Energy, Power Generation Agriculture Defence Industry Medical, Orthopedics Textile Industrial Pumps and Valves Machine Tool Industry Food and Dairy Processing Others ADVANTAGES OF OUR INVESTMENT CASTING COMPARING TO OTHER TRADITIONAL PRODUCTION METHODS SAND CASTING Finer surface quality Closer dimensional tolerances Lower or none draft angles No split lines Superior material microstructure and much less porosity, inclusions and segregations Lesser need for machining MACHINING Lesser need for Machining by means of Near net shapes No material loss Casting of different material types, shapes and geometries which are not possible to produce by Machining High production capacities (rates) Low cost FORGING Finer surface quality No split lines Homogenous internal stress Low cost due to lesser Machining Products with holes, spaces, pockets and internal geometries which are not possible to produce by Forging Lesser cost of molds WELDING Cost reduction, by changing the design from many welded parts to one part investment casting Higher mechanical characteristics by the elimination of welding defects and ITAB areas Finer surface quality Design freedom; not limited to fixed elements i.e.rods or metallic sheets Possibility to create logo, writings and complex figures on the casting BLANKING/BENDING(TWISTING)/DEEP DRAWING More design flexibility Flexibility in production of complexgeometries Low mold production cost and maintenance cost Possibility to create logo, writings and complex figures on the casting Designing different wall thicknesseson the same product Unlimited material / alloy selection POWDER METALLURGY/MIM Finer surface quality and close linear tolerances Producing more complex geometries No shrinkage as in sintering process in powder metallurgy Homogenous microstructure to minimise linear tolerance defects Unlimited dimensions and weights to produce Low mold cost Unlimited material / alloy selection
3 ALLOYS WE CAN POUR As Cevik Technical Metallurgy, we can pour over hundred alloys for investment casting: ferrous as well as non ferrous alloys. Most common alloys for investment casting are : Austenitic Stainless Steel Low Alloy and Carbon Steels Martensitic Stainless Steel Tool Steels Nickel Base Alloys Cobalt Base Alloys Aluminıum Alloys Copper Alloys (Brass / Bronze)
4 - DESIGN CRITERIAS LINEAR TOLERANCES General Linear Tolerances British System Up to 2 : +/ , additional +/ for each additional inch Metric System Up to 50mm : +/- 0.50mm, additional +/-0.25 mm foreach additional 25 mm Standard Linear Tolerances British System Up to 1/2 : +/ Up to 1 : +/ Up to 2 : +/ For each additional inch, additional : +/ Metric System Up to 15 mm : +/ mm Up to 25 mm : +/ mm Up to 50 mm : +/ mm For each additional 25 mm, additional : +/ mm It is advised to use Standard Linear Tolerances for functional part dimensions Special Linear Tolerances Advised Techniques if linear tolerances are required: i) Re-design the product with additional bars, brackets and gussets ii) Adjusting wax injection wax to the nominal dimensions after the prototype iii) Flatness and Straightness iv) Jigging and manual straightening v) Machining vi) Other secondary treatments Premium tolerance practicability should be checked for each diemension of each part. Other Tolerances Straightness-Flatness Depending on the lenght, Parts can be casted straight and flat within 0.10 mm tolerance. For thicker parts this tolerance can be up to 0.25 mm. Roundness Hole profile is within Standard Linear Tolerances. When required, Premium Linear Tolerances can be applied. If possible, it is advisable to apply General Linear Tolerances. Concentricity The gap between the centers of two cylindrical surfaces -which are sharing a common point or an axis as their center-, is not more than the gap between their diameters multiplied by 0.10 mm. If the height of a cylinder is more than two times of its diameter Straightness Tolerance should be added to eccentricity. Angularity As a standard rule, +/- 0.5 degrees or +/ ofthe length is a normal tolerance for production. For some cases, Angular Tolerance can go down to +/ degrees or go up to +/- 1.0 degrees
5 Cast Characteristics General Rules Hole Diameter Hole Length Between 1.5mm to 2.5mm: 2 x hole diamater Between 2.5mm to 5.0mm: 3 x hole diamater Between 5.0mm to 10mm : 4 x hole diamater Over 10mm : 6 x hole diamater By using ceramic core, hole length can be increased to 30 x hole diameter. Blind Holes Hole Length = Hole Diameter Counterbores / Grooves Blind grooves can be casted up to 1.5 x width Wall Thicknesses / Corner Radius (Radii) Minimum Wall thikness and Corner Radius depends on the configuration and the dimensions of the part. In some casts, it is possible to have 0.3mm Wall Thicknesses and R 0.3mm Corner Radius. Surface Roughness Standart Surface Roughness in İnvestment casting is125 RMS (Ra ). It is possible to improve Surface Roughness by using secondary methods and treatments. Runners For each section, one or more Runners with a thicker cross-section are used. After solidification, these Runners are removed by Grinding. Internal Radii, Fillets Internal radii and fillets improve the strength andintegrity of the casting and minimise internal stresses. It is advisable to increase Internal Radii Engraving Engraving should be raised letters on a recessed pad, so the top of engraving is below the surface of the part which is easier, more economical and without any defects. Metallurgical and Visual Quality Requirements Design, Material Type, Heat Treatment and Visual details should be discussed and decided between Customer and Cevik Technical Metallurgy. Specific Requirements All other requirements should be discussed and clarified together with our Technical Team before Order and Production
6 SOME INVESTMENT CASTING SOLUTIONS Design Advantage Application: Machinery Design Problem: High manufacturing costs, difficultweldment, Poor quality Solution: one piece investment cast, quality improvement, 20% cost reduction Performance Advantage Application: Bottling Performance Problem: Short life time, High wear, High costs Solution: New product with cobalt based alloy, Product life time increased, 30% cost reduction Cost Advantage Application: Material Handling Cost Problem: Difficult to machine, Complex shape, Unusual alloy Solution: Investment cast component, 50% savings Here above example is still under design. Our Application Team worked together with our Customer to find an optimum solution using Investment Casting. Advantages of Investment Casting on this Design: Number of total parts were decreased from 33 pcs. to 10pcs. Stainless steel was used instead of carbon steel Dimensions are reduced and total weight was decreased Mechanical properties of load carrying components were improved Consistency on Standart Quality Weldement and Machining Processes were eliminated Much better aeshetics Engineering wise Approximately 65% Cost Reduction
Lost Wax. Investment casting
Lost Wax Investment casting The process knowledge Technical department Experienced engineers Modern CAD equipment Casting and solidification simulations Design assistance Die tools and pattern injections
More informationDesign for Forging. Forging processes. Typical characteristics and applications
Design for Forging Forging processes Forging is a controlled plastic deformation process in which the work material is compressed between two dies using either impact or gradual pressure to form the part.
More informationMetal extrusion. Metal stamping
Metal extrusion Answer the following questions 1. In which of the following extrusion operation is friction a factor in determining the extrusion force (one best answer): (a) direct extrusion or (b) indirect
More informationSolidification of Metals in Molds
Metal Casting Solidification of Metals in Molds Pure Metals - Solidify at a constant temperature Planar solidification front Columnar crystals Eutectics - Solidify at a constant temperature Planar solidification
More information600 Cannonball Lane O Fallon, MO Revision 8/11/2015.
600 Cannonball Lane O Fallon, MO 63366 Revision 8/11/2015 http://www.ofalloncasting.com/ Topic Page Table of Contents 2 Introduction to Investment Casting 3 Drawing Notes 8 Minimum Drawing Notes 9 Material
More informationDedicated to Quality, Service & Partnerships
Dedicated to Quality, Service & Partnerships Company Introduction With a focus on investment casting, Acewell was established in 1998 and over the years has forged a reputation for dependable quality manufacturing.
More informationCasting and Permold Product Portfolio
Casting and Permold Product Portfolio Sourcing and Supply Chain Solution for OEM Serving Industry For 25Yrs Our Mission is to reduce our clients total cost of ownership Sourcing Supply Chain Management
More information2890 Ligonier St. Latrobe, PA Phone Fax Toll Free
Your Best Choice For Carbide Components 2890 Ligonier St. Latrobe, PA 15650 Phone 724.532.3041 Fax 724.532.3043 Toll Free 800.862.7066 www.extramet.net OUR HISTORY OUR MISSION Extramet s Primary Objective
More informationMasterflex Polishing Products
Masterflex Polishing Products How to Order Masterflex Polishing Products When ordering it is important to give as much information about the operation as possible so that the correct grading is supplied.
More informationProcessing of Engineering Materials
Unit 7: Unit code Machining and Processing of Engineering Materials A/615/1481 Unit level 4 Credit value 15 Introduction Practical articles that we see and use every day such as automobiles, aircraft,
More informationChapter 14: Metal-Forging Processes and Equipments
Manufacturing Engineering Technology in SI Units, 6 th Edition Chapter 14: Metal-Forging Processes and Equipments Chapter Outline Introduction Open-die Forging Impression-die and Closed-die Forging Various
More informationPrimary shaping - Powder Metallurgy
Chair of Manufacturing Technology Primary shaping - Powder Metallurgy Manufacturing Technology II Exercise 2 Laboratory for Machine Tools and Production Engineering Chair of Manufacturing Technology Prof.
More informationPowder-Metal Processing and Equipment
Powder-Metal Processing and Equipment Text Reference: Manufacturing Engineering and Technology, Kalpakjian & Schmid, 6/e, 2010 Chapter 17 Powder Metallurgy Metal powders are compacted into desired and
More informationCasting Process Part 2
Mech Zone Casting Process Part 2 (SSC JE Mechanical/ GATE/ONGC/SAIL BHEL/HPCL/IOCL) Sand Casting cope: top half drag: bottom half core: for internal cavities funnel sprue runners gate cavity {risers, vents}
More informationPowder Metallurgy. Powder-Metal Processing and Equipment 11/10/2009
Powder Metallurgy Powder-Metal Processing and Equipment Metal powders are compacted into desired and often complex shapes and sintered* to form a solid piece * Sinter: To heat without melting Text Reference:
More informationCountersinks. Smooth cutting, perfect chamfering - Counterbores - Cross Hole - Single Flute - Three Flute
Countersinks Countersinks Smooth cutting, perfect chamfering - Counterbores - Cross Hole - Single Flute - Three Flute smooth cutting perfect chamfering countersinks Product Code: C108 This new generation
More informationTailor Made Casting Designs. Casting. Innovation
HIGH GRADE STEEL & PRECISION CASTING Technical Bulletin No. 4 Casting Engineering Innovation Tailor Made Casting Designs Wolfensberger Casting Engineering optimises design ideas with focus on the result.
More informationPowder Metallurgy Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014
Powder Metallurgy Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014 TOPIC OUTLINE What Is Powder Metallurgy (P.M)? Powder Metallurgy Processes Blending And Mixing Compaction
More informationFundamentals of Casting
Fundamentals of Casting Chapter 11 11.1 Introduction Products go through a series of processes before they are produced Design Material selection Process selection Manufacture Inspection and evaluation
More information7. Design for Castability
7. Design for Castability Castability implies ease of producing a casting, minimising cost, defects and lead-time. This is facilitated by high compatibility between product requirements and process capabilities.
More informationCarbide Tip Coolant Fed Drills
KOOLTWIST, KOOLCARB, KOOLDEX Carbide Tip Coolant Fed Drills KOOLTWIST HIGH PERFORMANCE High performance, helical point, stub length. For alloy steels, tool steels, free machining stainless steels, Style
More informationLicensed Copy: John May, Powertrain Ltd., February 20, 2002, Uncontrolled Copy, (c) BSI
BRITISH STANDARD BS 70-3: Incorporating Amendment Nos. 1 and 2 Specification for Wrought steel for mechanical and allied engineering purposes Part 3: Bright bars for general engineering purposes BS70-3:
More informationProfile Milling Program Tools
Profile Milling Program Tools Small Ball Nose & Back raft Inserts VRBS 2 imensions R XRN TN HSN escription VRBS-0250 0.250 0.294 0.125 Used for semi and finish-milling small radius or detail work, VRBS-0312
More informationForging Solutions. Open Die and Rolled Ring Forging the Processes, Applications and Benefits
Forging Solutions Open Die and Rolled Ring Forging the Processes, Applications and Benefits The Open Die Forging Process Steps to produce a typical spindle-shaped part: 1. Starting stock cut to size by
More informationUnlock the Potential. Low Cost, On-Demand Metal 3D Printing
1 Unlock the Potential Low Cost, On-Demand Metal 3D Printing 2 3DEO - Unlock the Potential of High Volume Metal Additive Manufacturing Contents About 3DEO Benefits of 3D Printing Intelligent Layering Technology
More informationUnlock the Potential. Low Cost, On-Demand Metal 3D Printing
1 Unlock the Potential Low Cost, On-Demand Metal 3D Printing 2 Contents About 3DEO Benefits of 3D Printing Intelligent Layering Technology Technical Specifications Technology Comparison Industries & Applications
More informationa service offered by the Hempel Special Metals Group
Hot Isostatic Pressing of Near Net Shaped Parts a service offered by the Hempel Special Metals Group content introduction description of the method supply chain aspects & quality management applications
More informationManufacturing Technology II. Exercise 2. Powder Metallurgy
Lehrstuhl für Technologie der Fertigungsverfahren Laboratorium für Werkzeugmaschinen und Betriebslehre Manufacturing Technology II Exercise 2 Powder Metallurgy Werkzeugmaschinenlabor Lehrstuhl für Technologie
More informationHSS rolled. HSS ground. HSS Co 5 ground. HSS-TiN ground. Twist drills DIN 338 type N. Point cuts:
Twist drills DIN 338 type N High performance twist drill suitable for all normal drilling in conventional materials. Point cut: helical point Helix angle: 20-30 tolerance: h8 Right-hand cutting 1,0 up
More informationSPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES FOR USE IN BOILERS AND OTHER PRESSURE VESSELS
2007 SECTION II, PART A SA-479/SA-479M SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES FOR USE IN BOILERS AND OTHER PRESSURE VESSELS SA-479/SA-479M (Identical with ASTM Specification A 479/A 479M-04
More informationEvery Industry - Every Day DIRECT METAL LASER MELTING. The Experts in Metal Additive Manufacturing.
DIRECT METAL LASER MELTING The Experts in Metal Additive Manufacturing Every Industry - Every Day www.gpiprototype.com 847-615-8900 Sales@GPIprototype.com GPI Prototype and Manufacturing Services has been
More informationUltra-met. carbide metalworking technologies (800) (866)
CEMENTED CARBIDE GRAIN STRUCTURES January 2006 720 North Main Street P.O. Box 313 Urbana, OH 43078 800.543.9952 866.543.9952 937.653.7133 Fax: 937.653.4754 CEMENTED CARBIDE GRAIN STRUCTURES January 2006
More informationMetal components getting too complex? Start from the smallest particles!
Metal components getting too complex? Start from the smallest particles! From powder to 15 tonnes of solid specialty steel Steam turbine rotor (650 kg) Courtesy of Siemens Industrial Turbomachinery AB,
More informationTotal Quality Management. Quick and Accurate Response to Inquiries. As-Promised Deliveries. Fair and Competitive Prices
FORGED SHAPES 1 2 MISSION STATEMENT The Anderson Shumaker team is dedicated to earning your loyalty and gaining your trust through: Total Quality Management Quick and Accurate Response to Inquiries As-Promised
More informationWe are focused on a positive, cooperative, environment that is quality driven by strategic alliances, steadfast commitments, and innovative
We are focused on a positive, cooperative, environment that is quality driven by strategic alliances, steadfast commitments, and innovative manufacturing solutions Management Team Steve Van Valzah Manufacturing
More informationMetal Forming Process. Prof.A.Chandrashekhar
Metal Forming Process Prof.A.Chandrashekhar Introduction Shaping of a component by the application of external forces is known as the metal forming. Metal forming can be described as a process in which
More informationChapter 14 Forging of Metals
Introduction Chapter 14 Forging of Metals Alexandra Schönning, Ph.D. Mechanical Engineering University of North Florida Figures by Manufacturing Engineering and Technology Kalpakijan and Schmid What is
More informationDHC. Differential Helix Cutter
DHC Differential Helix Cutter Universal Short and Long End Mills for the Highest Productivity in Roughing and Finishing Applications (Standard & with Corner Radius) 2 x d 1 x d DHC (Differential Helix
More informationAluminium and aluminium alloys. Castings. Chemical composition and mechanical
BSI titles relevant to the cast metals industry (as at 20/5/9) BSI Title International Equiv Aluminium and aluminium alloys. Castings. Chemical composition and mechanical where known 94/713477DC properties
More informationIntroduction to Manufacturing Technology
Introduction to Manufacturing Technology Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014 TOPIC OUTLINE What is manufacturing? Historical development of manufacturing
More informationINDEX. Drills. High Speed Steel 1/2" Round Shank S & D, 118 Point, Surface Treated Drill Sets
D R I L L S 2 0 0 1 NOTES INDEX PRODUCT STYLE NO. PAGE STYLE NO. PAGE JOBBERS LENGTH, GENERAL PURPOSE High Speed Steel Fractional Sizes, 118 Point, Surface Treated................1600.....1 Fractional
More informationInitial Reliability Requirements
Summary Initial Reliability Requirements Part, Process or Characteristic Major Minor Raw Material 92 90 Machined Parts (General Features) 97 92 Sheet metal fabrication 92 90 Composite Parts 97 90 Fastener
More information" Understanding your scheduling can save time and money
" Understanding your scheduling can save time and money The Specialists Galvin Machined Castings is a division of Galvin Engineering which was formed in 1930. Our foundry incorporates a highly experienced
More informationSurface Finishing Solutions
Surface Finishing Solutions ABRASIVE TECHNOLOGICAL EXCELLENCE Surface Finishing Solutions Aggregate Technology Aggregate products are manufactured by binding treated grains together using an optimised
More informationFlap wheels The pro for flexible stock removal
The pro for flexible stock removal TRUST BLUE Abrasive solutions with high stock removal Application specific design for high flexibility Comprehensive range provides solutions for different applications
More informationCarbide Modular Shrink System
Carbide Modular Shrink System Insert Shrink Fit HEA Shrink Fit SHANK Type Code Tool imensions imensions Ø1 Tool Ø1 VB, VRBS CHTAV-0250-0.460 1.700 0.879 CHTAV-0312-0.460 1.700 0.827 TO, HF, FB, BS, MB,MBT,
More informationis detrimental to hot workability and subsequent surface quality. It is used in certain steels to improve resistance to atmospheric corrosion.
Glossary of Terms Alloying Elements ALUMINIUM - Al is used to deoxidise steel and control grain size. Grain size control is effected by forming a fine dispersion with nitrogen and oxygen which restricts
More informationAEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION AMS 5659L Issued SEP 1965 Revised JAN 2004 Superseding AMS 5659K Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30CB (Nb) - 3.5Cu
More informationKNIVES. giving you the EDGE, to stay AHEAD. TUBE & METAL FORMING
KNIVES giving you the EDGE, to stay AHEAD. TUBE & METAL FORMING ATLAS has comprehensive in-house designing facility to design new products according to customer s specific requirements with complete satisfaction
More informationINFO SERVICE CHANGES IN THE STANDARD EN /4
INFO SERVICE CHANGES IN THE STANDARD EN 10253-2/4 en Introduction 4 General Information 5 Terms 7 Comparison pren 10253-2/4:2017 to EN10253-2:2007 / EN10253-4:2008 8 27 Information to be supplied by the
More informationREVIEW OF MICROSTRUCTURE AND PROPERTIES OF NON- FERROUS ALLOYS FOR WORM GEAR APPLICATION & ADVANTAGES OF CENTRIFUGALLY CAST GEARS
REVIEW OF MICROSTRUCTURE AND PROPERTIES OF NON- FERROUS ALLOYS FOR WORM GEAR APPLICATION & ADVANTAGES OF CENTRIFUGALLY CAST GEARS GIRI RAJENDRAN JASON HASSEN MCC INTERNATIONAL INC OVERVIEW OF NON-FERROUS
More informationRAPID PATTERN BASED POWDER SINTERING TECHNIQUE AND RELATED SHRINKAGE CONTROL
RAPID PATTERN BASED POWDER SINTERING TECHNIQUE AND RELATED SHRINKAGE CONTROL Jack G. Zhou and Zongyan He ABSTRACT Department of Mechanical Engineering and Mechanics Drexel University 3141 Chestnut Street
More informationRD-SAF Face milling and profiling cutter with positive round inserts
RD-SAF Cutter program, RD 2, RD 6, RD 20 ødm (CM) m l 2 ødm m B ød c ød c Morse taper Arbor mounting D c D 3 Max. dm m l 2 l 3 B F Z Nb of inserts Coolant channels Morse taper RD-2/032-03-CM3-080 20.00
More informationProducing Metal Parts
Producing Metal Parts CNC vs. Additive Manufacturing www.3dhubs.com METAL KIT 2 Introduction This Kit discusses how to select the right manufacturing process for metal parts by comparing CNC and Additive
More informationAL LM6 HOLLOW CYLINDER FABRICATED USING CENTRIFUGAL CASTING
AL LM6 HOLLOW CYLINDER FABRICATED USING CENTRIFUGAL CASTING Saifulnizan Jamian 1, Safwan Yutiman 2 and Haffidzudin Hehsan 3 1 Crashworthiness and Collisions Research Group, Universiti Tun Hussein Onn Malaysia,
More informationTOOLMAKER SOLUTIONS Rotary Tool Blanks
TOOLMAKER SOLUTIONS Rotary Tool Blanks Cemented carbide blanks for drills and end mills TABLE OF CONTENTS HYPERION ROTARY TOOL BLANKS SOLID BLANKS 04 06 END MILL BLANKS WITH CHAMFER, GROUND TO HYPERION
More informationBZN COMPACTS TOOL BLANKS AND INSERTS
BZN COMPACTS TOOL BLANKS AND INSERTS BZN COMPACTS TOOL BLANKS AND INSERTS Sandvik Hyperion manufactures a complete line of high quality polycrystalline CBN products for machining ferrous materials. The
More informationCOMBICLICK Fibre Discs with Patented Cooling and Quick-Mounting System
COMBICLICK Fibre iscs with Patented Cooling and Quick-Mounting System COOL QUICK COMBICLICK Reduction of the thermal load of tool and workpiece Very high stock removal rate and tool life Smooth grinding
More informationMetal Powder - the Raw Material of Future Production
Metal Powder - the Raw Material of Future Production BY GÜNTER BUSCH* SYNOPSIS Alongside Mobile Internet, Cloud Computing, Robotics, Energy Storage and Autonomous Vehicles, Additive Manufacturing is one
More informationAdditive Manufacturing Technology November
Additive Manufacturing Technology November 2012 www.3trpd.co.uk Phil Kilburn DMLS Sales Manager Agenda About 3T RPD Ltd Overview of Additive Manufacturing Manufacturing directly in metals Arcam - Electron
More informationDr. M. Medraj Mech. Eng. Dept. - Concordia University Mech 421/6511 lecture 12/2
POWDER METALLURGY Characterization of Engineering Powders Production of Metallic Powders Conventional Pressing and Sintering Alternative Pressing and Sintering Techniques Materials and Products for PM
More informationPrice/1. Price/1. Price/1. 1/ 8 3/ 8 1 1/ 2 1/ 8 10g -4580K / 4 3/ 4 2 1/ 2 1/ 4 30g -4660K / / 2 3/ 8 60g -4740K 291.
2 Flute For optimum performance and maximum swarf removal when plunging, slotting and routing in most materials including brass, aluminium, non-ferrous and other soft materials. Manufactured to USCTi Standards.
More informationASTM Standards for Pipe & Fittings
for Pipe & Fittings There are many International Standards for stainless and carbon steel pipes and fittings. The list below is a basic overview of some of these. For more in-depth details of these Standards
More informationDETAIL SPECIFICATION FITTINGS, PIPE, CAST BRONZE, SILVER-BRAZING, GENERAL SPECIFICATION FOR
INCH-POUND 20 December 2016 SUPERSEDING MIL-F-1183J 5 May 1987 DETAIL SPECIFICATION FITTINGS, PIPE, CAST BRONZE, SILVER-BRAZING, GENERAL SPECIFICATION FOR This specification is approved for use by all
More informationAEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION AMS 5643Q Issued OCT 1951 Revised JAN 2003 Superseding AMS 5643P Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb - 4.0Cu Solution
More informationA Practical Design Guide for Welded Connections Part 1 Basic Concepts and Weld Symbols
A Practical Design Guide for Welded Connections Part 1 Basic Concepts and Weld Symbols by James Doane, PhD, PE Course Overview This course is divided into 2 parts. Though it provides some basic concepts
More informationPart HD head control arm
Part HD head control arm Quality characteristics Dimension: height, width, wall thickness Mechanical properties of materials: hardness, brittleness, and porosity. Machining Dimension: holes, grooves, and
More informationAlloys SUPER SQUARE
Alloys ETD 150...8-2 ETD 150 Rounds...8-2 AISI 4140/41L40 - Annealed...8-3 AISI 4140 - Annealed Flats And Squares... 8-4 thru 8-5 AISI 4140 - Annealed Rounds... 8-5 thru 8-6 AISI 4140 Rounds HR Q&T...8-7
More informationA Case For Liquidmetal Alloys
WHITE PAPER A Case For Alloys A new material and process is making its introduction into the manufacturing realm. Could alloys be the answer to many of your manufacturing difficulties? See how the material
More informationTungsten Carbide Rotary Burrs
Tungsten Carbide Rotary Burrs Solutions for Industry www.master-abrasives.co.uk Introduction Master Abrasives The MASTER brand is known internationally as a high-quality brand of abrasives, tools and consumables
More informationRapidest Prototyping: Automotive Prototype Castings with 3D Printing. Sonhar Balagopalan Key Accounts Asia Pacific
Rapidest Prototyping: Automotive Prototype Castings with 3D Printing Sonhar Balagopalan Key Accounts Asia Pacific Give your customers Good surprises! Lets find all bad surprises before start of production!!
More informationSPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES
SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES A02 (Identical with ASTM Specification A 276-97.) 1. Scope 1.1 This specification covers hot-finished or coldfinished bars except bars for reforging (Note
More informationALUMINIUM ALLOY SAND AND CHILL CASTINGS Gr M
ALUMINIUM ALLOY SAND AND CHILL CASTINGS Gr. 4635 M FOR INTERNAL USE ONLY REMOVE THIS PREFACE BEFORE ISSUE TO SUPPLIERS Comparable Standards: 1. INDIAN : IS: 617-1994 Grade-4635 M 2. GERMAN : DIN 1725-1983,
More informationCoroDrill 428 Wide range of application possibilities
A CoroDrill 428 Wide range of application possibilities Gun drills DEE HOLE MACHINING Highly productive gun drills B Easy to use Solid carbide gun drills 428.5 - Diameter range: 0.8-12.00 mm (.031 -.472
More informationCHAPTER 14. Forging of Metals. Kalpakjian Schmid Manufacturing Engineering and Technology Prentice-Hall Page 14-1
CHAPTER 14 Forging of Metals 2001 Prentice-Hall Page 14-1 Forging (a) (b) Figure 14.1 (a) Schematic illustration of the steps involved in forging a bevel gear with a shaft. Source: Forging Industry Association.
More informationMounted Points. Table of Contents 2 I 203. Power Tools Contents Page. Power Tools Contents Page
203 Table of Contents Power Tools Contents Page General Information 3 Your Quick Product Selection Guide 4-5 Peripheral Speeds, Safety Notes 6 Mounted Points Vitrified Bond, Aluminum Oxide, Hardness Grade
More informationTechnical Information
Diamondtools Technical Information The Diamond Diamonds are the hardest known material.they are selected depending on the field of application. For diamond blade manufacture synthetic diamonds are solely
More informationBMM3643 Manufacturing Processes Powder Metallurgy Process
BMM3643 Manufacturing Processes Powder Metallurgy Process by Dr Mas Ayu Bt Hassan Faculty of Mechanical Engineering masszee@ump.edu.my Chapter Synopsis This chapter will expose students to the sequence
More informationEngineered Parts Your Design Our Competence
Engineered Parts Your Design Our Competence Engineered Parts by Bossard Your Design Our Competence Competent Partner Proven Quality Highest Supply Reliability Optimum Price-Performance-Ratio Competent
More informationCourse Description EMME 1
Course Description 01211211 Introduction to CAD/CAM 3(2 3 6) CAD/CAM systems for production engineering, hardwares and softwares for CAD/CAM systems, wireframe, surface and solid design, three dimension
More informationALWAYS A WINNING HAND
ALWAYS A WINNING HAND NORTON ABRASIVES AND TOOLS An operator s and production foreman s perfect tool: our new Norton pneumatic die grinder quickly and comfortably accomplishes many portable applications
More informationBuyers Guide to Perforated Metals
101 Commerce Street Glastonbury, CT 06033 Phone: 800.443.5218 & 860.659.0591 Fax:: 860.659.8705 Web: ConardCorp.com Buyers Guide to Perforated Metals Presented by Conard Corporation Share this guide 2
More informationIndian Stainless Steel Development Association ISSDA Conference. Venue: Hotel Grand, New Delhi
Indian Stainless Steel Development Association ISSDA Conference Date: 7 th November 2014 Venue: Hotel Grand, New Delhi 1 Challenges in Manufacture of Making of Heavy Stainless Steel Forgings dual certified
More informationSlurry-Based Semi-Solid Die Casting
Accepted for Publication in Advanced Materials and Processes, 159(10), October 2001 Slurry-Based Semi-Solid Die Casting Chris S. Rice and Patricio F. Mendez A new approach to semi-solid forming is described.
More informationSAND CASTING - INVESTMENT CASTING
Since 1967... SAND CASTING - INVESTMENT CASTING www.gedikdokum.com Gedik Casting and Valve, a subsidiary of Gedik Holding, which is active in Sand Casting, Investment Casting and Valve sectors since 1967.
More informationCHAPTER 1 INTRODUCTION
1 CHAPTER 1 INTRODUCTION 1.1 ALUMINIUM ALLOYS Aluminium and its alloys offer an extremely wide range of capability and applicability, with a unique combination of advantages that make the material of choice
More informationA wide range of cold-formable steel grades and aluminium alloys are used as wire materials within a diameter range from 5 mm to 34 mm.
Cold-Formed Parts 2 ESKA manufactures complex precision cold-formed parts for applications with large and medium quantities. The highly-efficient cold- forming process ensures economic manufacture of near-net-shape
More informationWIRE SIZE HUTCHINSON HSS BLANKS
DRILL & REAMER BLANKS WIRE SIZE HUTCHINSON HSS BLANKS Wire Decimal Overall Net Price Net Price Size Equivalent Inches Each Each 1.2280 3 7 /8 2.2210 3 7 /8 3.2130 3 3 /4 4.200 3 3 /4 5.2055 3 3 /4 6.2040
More informationEUROFER position paper 1 determining the borderline between preparations/articles for steel and steel products
EUROFER position paper 1 determining the borderline between preparations/articles for steel and steel products Background Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18
More informationALUMEC. High strength aluminium
High strength aluminium This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationSpecial Tool Configurations
Special Tool Configurations Special Overall and/or Flute Lengths While we recoend using a standard overall and flute length whenever possible, there are situations where the use of special overall and/or
More information4 Flute All Purpose. duramill.com. for steels, stainless steels and high-temp alloys. roughing, slotting, pocketing & ramping applications
4 Flute All Purpose for steels, stainless steels and high-temp alloys roughing, slotting, pocketing & ramping applications duramill.com 2 4 Flute AP The new WhisperKut GEN2 4 Flute AP has been engineered
More informationSample2 EXAM 2 Name Closed book, allowed a 5x7 card, calculator, and brain. Budget your time!
MEEN 3344 001 Material Science Sample2 EXAM 2 Name Closed book, allowed a 5x7 card, calculator, and brain. Budget your time! Definitions: (10 terms, each definition is worth 1.5 points, 15 total) Match
More informationMetal Casting Dr. D. B. Karunakar Department of Mechanical and Industrial Engineering Indian Institute of Technology, Roorkee
Metal Casting Dr. D. B. Karunakar Department of Mechanical and Industrial Engineering Indian Institute of Technology, Roorkee Module 02 Sand Casting Process Lecture 12 Design Of Risering System-IV Good
More informationDiamond abrasives offering customized and tailored solutions for demanding applications. TOOLMAKER SOLUTIONS MBG Diamond
Diamond abrasives offering customized and tailored solutions for demanding applications TOOLMAKER SOLUTIONS MBG Diamond MBG DIAMOND FOR DEMANDING GRINDING APPLICATIONS Hyperion s MBG diamond offers a solution
More informationMounted points Catalogue Page
Catalogue Page 1 able of contents General information he fast way to the best tool 4 General information on mounted points 6 Explanation of the description 7 rive spindle extensions 8 Mounted points For
More informationResource Guide. Section 2: Gray Iron
Resource Guide Section 2: Gray Iron Section 2 Gray Iron Description of Grades... 2-3 G1 Partially Ferritic... 2-4 G1A Ferritic... 2-6 G2 Highly Pearlitic... 2-8 G2A Highly Perlitic High-Strength... 2-10
More informationManufacturing Methods and Material Selection
Manufacturing Methods and Material Selection ENM 214 Dr. Tolga Yasa Mechanical Engineering Department MAK 208 Introduction: Design Process Product design the process of defining all of the product characteristics
More informationInvestigation of direct metal laser sintering process Slavko Dolinšek
Investigation of direct metal laser sintering process Slavko Dolinšek This paper presents some characteristics of the direct metal laser sintering (DMLS) process and applications of this technology in
More information