Typical Characteristics Appearance transparent, viscous liquid Specific gravity at 25 C 0.89 g/cm 3. Solvents 1-Propanol 21% n-propyl acetate 44%
|
|
- Geoffrey Booth
- 5 years ago
- Views:
Transcription
1 Printing & Packaging Technical Data Sheet Versamid PUR Product Description Versamid PUR is a thermoplastic polyurethane resin for flexographic printing ink applications. Key Features & Benefits Chemical Composition - Excellent cohesion, flexibility and adhesion to a variety of films - Excellent solvent release - Good pigment dispersion capability Thermoplastic polyurethane resin in an alcohol/acetate solution blend Properties Product Specifications Solids Viscosity at 25 C 500 1,150 cps Gardner color 1 2 max Typical Characteristics Appearance transparent, viscous liquid Specific gravity at 25 C 0.89 g/cm 3 Solvents 1-Propanol 21 n-propyl acetate 44 1 Gardner Holdt Color at 35 total non-volatiles (TNV) as supplied. These typical values should not be interpreted as specifications. Applications Versamid PUR is a 35 solids solution in a solvent blend of n-propanol and n-propyl acetate. Versamid PUR is a film former that is soluble in a variety of alcohols and co-solvent (alcohol and hydrocarbon) systems for use in flexographic or gravure lamination inks. Since it is completely dilutable in alcohol, a finished ink can be formulated that will not swell flexographic printing plates. Versamid PUR can be formulated into inks that provide excellent cohesion, flexibility and adhesion to various polyolefin, polyester, polymer coated and metalized films. s formulated with Versamid PUR exhibit excellent adhesive and cohesive strength in both adhesive and extrusion laminates. In addition, it has sufficient block resistance to be used as a surface printing ink vehicle. Versamid PUR is recommended for applications such as: Printing inks for flexographic or gravure applications July 2014 Rev 3 Page 1 of 5
2 Formulations White Formula Materials n-propanol Iso-propanol Versamid PUR 23.9g 23.9g TiO g 41.5g n-propanol 20.8g 0g Iso-propanol 0g 20.8g Add 30g of 4mm glass beads and grind for 30 minutes on paint shaker, measure grind viscosity then add: 27 Seconds (Zahn #3) 24 seconds (Zahn #3) n-propanol 13.8g 0g Iso-propanol 0g 13.8g Total 100.0g 100.0g Formulation attributes Pigment: Binder ratio 5.0:1 5.0:1 Solids as printed Viscosity (Zahn #2) 22 seconds 23 seconds Blue Formula Materials n-propanol Iso-propanol Versamid PUR 39.8g 39.8g Sunfast 2 Blue g 12.4g n-propanol 12.4g 0g Iso-propanol g Add 30g of 4mm glass beads and grind for 60 minutes on paint shaker, measure grind viscosity then add: 42 Seconds (Zahn #X) 43 seconds (Zahn #X) n-propanol 35.4g 0g Iso-propanol 0g 37.8g Total 100.0g 102.4g Formulation attributes Pigment:Binder ratio 1.0: :1.1 Solids as printed Viscosity (Zahn #2) 23 seconds 22 seconds Versamid PUR and Co-resin Compatibility Solids Ratio (Urethane:Co-Resin) Co-Resin 4:1 1:1 Poly(vinylbutyral) C C Cellulose acetate butyrate C C Cellulose acetate propionate I I Polyketone C C Fumaric modified rosin ester (20 in n-propanol) C C Versamid 757 (35 in n-propanol) I PC (slightly hazy) Versamid 759 (35 in n-propanol) C C Versamid 963 (20 in n-propanol) I I Versamid 973 (20 in n-propanol) I I Nitrocellulose PC^ PC^ Key: C = compatible, I = incompatible, PC = partially compatible ^Solution was compatible and completely clear but discolored and showed limited viscosity increase. Versamid PUR and Additive Compatibility Additive Solids Ratio (Urethane:Additive) Result Polyethylenimine 98:2 I Titanate 98:2 C Resinous gum 95:5 I Silanes 98:2 C Polyaziridine 95:5 C ed isocyanate 92:8 C Melamine 95:5 C Key: C = compatible, I = incompatible, PC = partially compatible Testing Parameters s were printed with a 165 Q anilox handproofer on polyester and polypropylene, PVDC coated polyester and nylon films. The adhesive was applied with a K-coater 3 using a #2 bar to achieve a coating weight of lb/ream. The adhesives were Adcote and Adcote A/B. July 2014 Rev 3 Page 2 of 5
3 The films were laminated to PE film (back sheet) using a card laminator at 175 F (79 C) for adhesive lamination and at 325 F (163 C) for extrusion lamination where films were laminated to PE film (back sheet) without any adhesive application. strengths were measured on a Thwing Albert 5 Model #225-1 Friction/Peel Tester operating in the 90 T-peel mode. Measurements were made after aging laminates for 3 days; FT = film tear. resistance was measured face-to-face and face-to-back at 50 C with 10 psi for 16 hours. Samples were given a numerical rating: 10 = best, no blocking 0 = worst, complete blocking The percent decal was rated as a : 100 = ink completely separated from substrate 50 = ink split, ink layer cohesive failure 0 = ink did not separate from substrate Polyester results Blue Versamid PUR PUR coverage Polypropylene results Blue Versamid PUR PUR coverage PVDC coated polyester results Blue Versamid PUR PUR coverage Adcote FT, > Adcote A/B FT, > Extrusion Adcote FT, > Adcote A/B Extrusion Adcote Adcote A/B Extrusion FT, > Adcote FT, > Adcote A/B FT, > Extrusion Adcote Adcote A/B Extrusion Adcote Adcote A/B Extrusion Adcote Adcote A/B FT, > Extrusion Adcote FT, > Adcote A/B FT, > Extrusion Adcote FT, > Adcote A/B Extrusion ² Registered trademark of Sun Chemical Company. 3 Registered trademark of RK PrintCoat Instruments Ltd. 4 Trademark of Dow Chemical Company. 5 Registered trademark of Thwing Albert Instrument Company. July 2014 Rev 3 Page 3 of 5
4 Nylon results Blue Versamid PUR PUR coverage Adcote Adcote A/B Extrusion Adcote Adcote A/B Extrusion Adcote Adcote A/B Extrusion Safety General The usual safety precautions when handling chemicals must be observed. These include the measures described in Federal, State, and Local health and safety regulations, thorough ventilation of the workplace, good skin care, and wearing of protective goggles. Material Safety Data Sheet All safety information is provided in the Material Safety Data Sheet for Versamid PUR. Storage Versamid PUR is supplied in solution form for ease of handling. Properly stored and protected, an unopened container of Versamid PUR should have a shelf life of at least one year. Use proper loading and grounding procedures when handling near flammable materials. Important While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, they are provided for guidance only. Because many factors may affect processing or application/use, BASF recommends that the reader make tests to determine the suitability of a product for a particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS, DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS, DESCRIPTIONS, DESIGNS, DATA OR INFORMATION MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. In no case shall the descriptions, information, data or designs provided be considered a part of BASF's terms and conditions of sale. Further, the descriptions, designs, data, and information furnished by BASF hereunder are given gratis and BASF assumes no obligation or liability for the descriptions, designs, data or information given or results obtained all such being given and accepted at the reader's risk. Versamid is a registered trademark of BASF Group. BASF Corporation, 2014 July 2014 Rev 3 Page 4 of 5
5 BASF Corporation is fully committed to the Responsible Care initiative in the USA, Canada, and Mexico. For more information on Responsible Care goto: U.S.: Canada: México: U.S & Canada Mexico BASF Corporation BASF Mexicana, S.A. de C.V W Eleven Mile Road Av. Insurgentes Sur # 975 Southfield, MI Col. Ciudad de los Deportes ph: 1(800) C.P fax:1(800) Mexico, D.F. Custserv_charlotte@basf.com Phone: (52-55) edtech_info@basf.com Fax: (52-55) July 2014 Rev 3 Page 5 of 5
Waterpoxy 751. Industrial Coatings. Technical Data Sheet. Properties. Applications
Industrial Coatings Technical Data Sheet Waterpoxy 751 Product Description Key Features & Benefits Chemical Composition Waterpoxy 751 is an amine-based curing agent in a water solution designed to cure
More informationAcronal PLUS Withstanding harsh environmental conditions for the commercial market
Withstanding harsh environmental conditions for the commercial market Withstanding harsh environmental conditions for the commercial market. is a flexible, 100% acrylic latex polymer for high performance
More informationAcronal PLUS Offering superior stain control for interior and exterior applications
Acronal PLUS 4641 Offering superior stain control for interior and exterior applications Formulate an interior or exterior primer that has excellent stain control using Acronal PLUS 4641. Acronal PLUS
More informationInnovative solutions for adhesive raw materials
Innovative solutions for adhesive raw materials Innovative solutions for adhesive raw materials Page 2 Adhesive raw materials for pressure sensitive label General Purpose Permanent General Purpose Removable
More informationVersamid 280 B-75. Technical Data Sheet. Properties. Applications. Product Description or liquid epoxy resins.
Technical Data Sheet Versamid 280 B-75 Product Description Key Features & Benefits Chemical Composition Versamid 280 B-75 is a polyamide/epoxy adduct in n-butanol designed for reaction with solid or liquid
More informationPerformance Products for Cementitious Systems
Performance Products for Cementitious Systems Products for Cement and Mortar To achieve ground-breaking formulations that have outstanding workability, pot life, physical strength, flexibility and adhesion
More informationSilGrip* PSA529. Technical Data Sheet
Technical Data Sheet SilGrip* PSA529 Description SilGrip* PSA529 silicone pressure sensitive adhesive is a toluene solution of polysiloxane gum and resin. It is supplied at 55 percent silicone solids and
More informationCellulose acetate butyrate in 2K acrylic urethane wood coatings Improving application and appearance ADD-COAT-7963
Cellulose acetate butyrate in 2K acrylic urethane wood coatings Improving application and appearance ADD-COAT-7963 Table of Contents Segment Overview Slide 13 Segment Challenges Addressed by CAB Slide
More informationAdhesives for Tapes: Packaging & beyond. Dow.com
Adhesives for Tapes: Packaging & beyond Dow.com OPP Packaging Tapes The Water Based Acrylic Technology Ready to use adhesive / No formulation Low foam formation and excellent flow at high speed Coating
More informationSolvents Eastman isobutyl isobutyrate (IBIB)
Eastman isobutyl isobutyrate (IBIB) CH 3 O CH 3 CH CH 2 O C CH CH 3 CH 3 Introduction Eastman isobutyl isobutyrate (IBIB) is an economical ester retarder solvent that is used in nitrocellulose lacquers,
More informationSimalfa 900-PU. Product Description. Key Properties. Certifications. Physical Properties
Revised: 2.27.2013 Simalfa 900-PU Product Description SIMALFA 900-PU is a high yielding and fast drying water based adhesive based on polyurethane dispersions that can be used in a wide variety of applications.
More informationSilGrip* PSA518 Pressure Sensitive Adhesive
Technical Data Sheet SilGrip* PSA518 Pressure Sensitive Adhesive SilGrip* PSA518 Pressure Sensitive Adhesive Description PSA518 silicone pressure sensitive adhesive is a xylene solution of phenyl based
More informationSilGrip* PSA595 Pressure Sensitive Adhesive
Technical Data Sheet SilGrip* PSA595 Pressure Sensitive Adhesive SilGrip* PSA595 Pressure Sensitive Adhesive Description PSA595 silicone pressure sensitive adhesive is a xylene solution of polysiloxane
More informationTechnical Bulletin 06/2011
DELTA-DC 4010 M Dispersion Control Additive Technical Bulletin 06/2011 DELTA-DC 4010 M is a wetting and dispersing additive for solvent-based coatings to improve pigment wetting, reduce the grinding time
More informationCoil coatings Improving efficiency, enhancing aesthetics
Coil coatings Improving efficiency, enhancing aesthetics Eastman cellulose esters ADD-COAT-7952 Table of Contents Segment Overview Slide 4 Segment Challenges Addressed by CAB Slide 7 Results Slide 9 Conclusion
More informationLOCTITE 406. Technical Data Sheet. (TDS for new formulation of Loctite 406 ) February-2012
Technical Data Sheet LOCTITE 46 (TDS for new formulation of Loctite 46 ) February-212 PRODUCT DESCRIPTION LOCTITE 46 provides the following product characteristics: Technology Cyanoacrylate Chemical Type
More informationScotch-Weld Metal Bonder Acrylic Adhesive DP8407NS Gray
Scotch-Weld Metal Bonder Acrylic Adhesive Preliminary Technical Data Sheet October 2017 Product Description is a high performance, two-part acrylic adhesive that offers excellent shear, peel, and impact
More informationADCOTE 555/ADCOTE 536B Laminating Adhesive
PACKAGING AND CONVERTING ADHESIVES AND SEALANTS ADCOTE 555/ADCOTE 536B Laminating Adhesive Description Adcote 555 is an isocyanate terminated polyester urethane component of a two component, highapplication
More informationSafety Data Sheet Magnetic Pigment 345 BASF Revision date : 2018/10/11 Page: 1/9
Revision date : 2018/10/11 Page: 1/9 1. Identification Product identifier used on the label Recommended use of the chemical and restriction on use Recommended use*: Colorants for industrial use Recommended
More informationSilGrip* PSA590LD silicone pressure sensitive adhesive
Technical Data Sheet SilGrip* PSA590LD silicone pressure sensitive adhesive Description SilGrip PSA590LD silicone pressure sensitive adhesive is a toluene solution of polysiloxane gum and resin. It is
More informationExtruded Technical Film Solutions
Extruded Technical Film Solutions Ex Tech is a full range of high-perfmance thermoplastic films & sheets, including polyurethane (TPU), polyester, polyamide, polyolefin and aliphatic urethanes. These materials
More informationTechnical Data Sheet February 2014
Scotch-Weld Technical Data Sheet February 2014 Product Description s are high performance, two-part acrylic adhesives with lower odor than most acrylic adhesives. These toughened products offer excellent
More informationDuraflex PF is a premium flexo solventbased multi substrate laminating system.
SunStrato Duraflex PF From the SunStrato family of lamination inks 1. Description Duraflex PF is a premium flexo solventbased multi substrate laminating system. 2. Product features* Duraflex PF inks-:
More informationSimalfa 335-Of {Overspray Free}
Revised: 11.29.2010 Simalfa 335-Of {Overspray Free} Product Description SIMALFA 335-OF allows for instant bonding and Overspray Free application. While all SIMALFA products can be sprayed with no overspray,
More informationProduct Data Sheet. NeoCryl BT-175
is a water borne alkali soluble acrylic copolymer that can be formulated into high performance flexographic and gravure inks which meet clear air regulations. When amine solubilized, can be used as a pigment
More informationKTR is delivered in 25 kg multi-ply paper bag. One pallet contains 900 kgs 36 bags. One 20 ft. container contains 18 metric tons.
STRUCTURAL FORMULA CAS Number - 25054-06-2 Trade Names - KTR-80, KTR-100, KTR-118, KTR-123 Chemical Name - CYCLOHEXANONE-FORMALDEHYDE RESIN 1. GENERAL DESCRIPTION Ketonic Resins (KTR) dissolve readily
More informationSafety Data Sheet Magnafloc LT-7989 Revision date : 2011/11/03 Page: 1/6
Revision date : 2011/11/03 Page: 1/6 1. Product and Company Identification Company BASF Mexicana S.A. de C.V. Av. Insurgentes Sur 975 Col. CD. De Los Deportes, C.P. 03710, MEXICO 24 Hour Emergency Response
More informationDriven by tomorrow. BASF pigments, resins and additives for the automotive and transportation coatings industry
Driven by tomorrow BASF pigments, resins and additives for the automotive and transportation coatings industry 2 Driven by tomorrow Global solutions, world markets, local presence Serving the needs of
More informationLow Odour Acrylic Adhesives DP8805NS Green DP8810NS Green DP8825NS Green. Preliminary Technical Data Sheet May 2017
Scotch-Weld Preliminary Technical Data Sheet May 2017 Product Description 3M Scotch-Weld are high-performance, two-part acrylic adhesives with lower odour than most acrylic adhesives. These toughened products
More informationPretreatment of fabrics that contain spandex
Technical Information January 2000 Pretreatment of fabrics that contain spandex Colorants and Finishing Products General information on spandex fibers Spandex fibers are made from a high-molar-mass polymer.
More informationProduct Bulletin 8991/8991R/8993
3M Controltac Scotchgard 8991 Removable 8991R High Gloss 8993 Product Description Characteristics Graphic Film Clear, tough, polyester overlaminates Product Features Product Bulletin 8991/8991R/8993 Release
More informationEPODIL LV5 Hydrocarbon Resin
Epoxy Curing Agents and Modifiers EPODIL LV5 Hydrocarbon Resin DESCRIPTION Epodil LV5 is a chemically inert, low viscosity liquid hydrocarbon resin. It is soluble in and compatible with a wide variety
More informationScotch-Weld Acrylic Adhesives
Scotch-Weld Acrylic Adhesives Technical Data Sheet October 2016 Product Description s are high performance, two-part acrylic adhesives that offer excellent shear, peel, and impact performance. These toughened
More informationHigh strength silicone moldmaking rubber
Technical Data Sheet High strength silicone moldmaking rubber Features & Benefits Outstanding release properties If required the product cure can be heat accelerated Fast thick section cure at room temperature
More informationLuviset CA 66. Technical Information. Copolymer with carboxyl groups for the production of hair sprays and hair setting preparations.
Technical Information Luviset CA 66 September 2005 Supersedes issue dated July 2005 MEMC 050414e-01/Page 1 of 10 = Registered trademark of BASF Aktiengesellschaft Copolymer with carboxyl groups for the
More informationAcronal acrylic resins
Technical Information EVP 002005 e, August 2005 Supersedes TI/ED 134, TI/ED 1104, TI/ED 1105 (all dates/languages) Page 1 of 5 = registered trademark of BASF Aktiengesellschaft, unless otherwise indicated
More informationSIMALFA 303. Product Description. Key Properties. Certifications. Physical Properties
Revised: 1.3.2011 SIMALFA 303 Product Description SIMALFA 303 is a one-part, low viscosity water based foam adhesive that bonds instantly. It is most commonly used where an extremely soft bond line is
More informationNominal 3 ft wide by 167 lineal ft (0.91 m wide by 50.9 m long)
INTRODUCTION LOCTITE EA 9896.025 WPP AERO is a pre-impregnated nylon peel ply product supplied in film form. It is a specially designed resin system capable of curing at 250 F (121 C). The experimental
More informationFeatures 100% solids Moisture curing urethane Rapid rate of strength build up Open time from 2-4 minutes Set times from seconds
3 Scotch-Weld TM Technical Data February, 2007 Product Description 3M Scotch-Weld s are 100% solid, warm temperature applied, moisture curing urethanes. These products bond a wide variety of plastics and
More informationTechnical Datasheet Ashland Performance Materials
Document 2437 V4 F2, Language EN V1, Approved 2013-4-3, 2013 Ashland Inc. Page 1 (5) Description PLIOGRIP 7700 two-part systems are high-strength, structural adhesives which are resistant to exposure to
More informationScotch-Weld Multi-Material & Composite Urethane Adhesives DP6310NS and DP6330NS
Adhesives Preliminary Technical Data Sheet January, 2017 Product Description 3M TM Scotch-Weld Adhesives are multi-purpose urethane adhesives for bonding a variety of composites, plastics, metals and wood.
More informationDOWSIL Neutral Plus Silicone Sealant
Technical Data Sheet Multi-purpose One-part Neutral Cured Silicone Sealant Features & Benefits Applications One-part room temperature cured silicone sealant Keeps flexibility at -40 C~150 C after cured
More informationXIAMETER RTV-4250-S Kit Green
XIAMETER RTV-4250-S Kit Green High strength silicone moldmaking rubber FEATURES Outstanding release properties If required the product cure can be heat accelerated Fast thick section cure at room temperature
More informationWater-borne pressure sensitive adhesives
Arkema Coating Resins AMERICAS Water-borne pressure sensitive adhesives Optimize Performance and Value with ENCOR Latexes More choice for Water-borne Pressure Sensitive Adhesives Finding the right adhesive
More informationPARALOID Edge 2301 Resin
Technical Data Sheet PARALID Edge 2301 Resin Solvent Borne Acrylic Carbamate Resin for Industrial Coatings Description Features and Benefits PARALID Edge 2301 Resin is a solvent borne, acrylic carbamate
More information- TECHNICAL SAFETY DATA SHEET
MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE 1958. Chem-Rez (Epoxy/Aggregate Coating) - TECHNICAL SAFETY DATA SHEET - MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE 1958. - MATERIAL
More informationThermal Conductive Adhesive Sealant (RTV)
Thermal Conductive Adhesive Sealant (RTV) PRODUCT DESCRIPTION TS-9001 Adhesive Sealant is a one-component, alcohol-released, and fast curing silicone which has excellent performance and good stability
More informationAchieving premium product appeal. Metasheen Superior mirror and liquid metal effects
Achieving premium product appeal Metasheen Superior mirror and liquid metal effects Agenda Metasheen at a glance Performance highlights Our global portfolio Guide formulations 2 Metasheen at a glance Metasheen
More informationProduct Information Paints, Inks & Coatings Dow Corning 52 Additive
Product Information Paints, Inks & Coatings Dow Corning 52 Additive FEATURES & BENEFITS Flowable liquid for processing ease Good compatibility with waterborne acrylic, alkyd, polyester, epoxy, PU and vinyl
More informationLuvimer 100 P Luvimer 36 D Polymer Luvimer 30 E
Technical Information January 2016 Supersedes issue dated October 2015 WF-No. 8236 04_050411e-06/Page 1 of 10 Luvimer 100 P Luvimer 36 D Polymer Luvimer 30 E Acrylic terpolymer products for hair-setting
More informationD.E.R. 684-EK40 Epoxy Resin Solution
Product Information D.E.R. 684-EK40 Epoxy Resin Solution Description Introduction D.E.R. 684-EK40 Epoxy Resin Solution is an ultra high molecular weight solid reaction product of epichlorohydrin and bisphenol
More informationAn extensive range of non-halogenated flame retardants
An extensive range of non-halogenated flame retardants Exolit Overview Under the tradename Exolit Clariant offers a distinctive range of non-halogenated flame retardants solutions providing more environmentally
More informationAn extensive range of non-halogenated flame retardants
An extensive range of non-halogenated flame retardants Exolit Overview Under the tradename Exolit Clariant offers a distinctive range of non-halogenated flame retardants solutions providing more environmentally
More informationCase and Carton Sealing: Hot melt Adhesive Solutions
Case and Carton Sealing: Hot melt Adhesive Solutions STICK INGTO INNOV ATION Imagine what s next Hot Melt Adhesives for Case and Carton Sealing A vast range of businesses and individuals from global brand
More informationDemelan AU-39/Bio. Technical Information. Mixture of quaternized ethoxylated fatty oil and ethoxylated fatty amine.
Technical Information Demelan AU-39/Bio May 2016 Supersedes issue dated February 2016 08_160103e-01/Page 1 of 5 WF-No. 8835 = Registered trademark of BASF in many countries. Mixture of quaternized ethoxylated
More informationARALDITE 2027 A/B (XD 4712/HARDENER XD 4713)
Advanced Materials ARALDITE 2027 A/B (XD 472/HARDENER XD 473) TWO-COMPONENT POLYURETHANE ADHESIVE Description ARALDITE 2027 A/B polyurethane adhesive is a two-component, room-temperature curing, beige-colored
More informationKraton polymers boost functional life of thermoplastic road marking paints
Kraton polymers boost functional life of thermoplastic road marking paints Outline Why modify with thermoplastic road marking paints? Other requirements from the market Kraton polymers introduction Improved
More information3 Scotch-Weld TM. Low-Odor Acrylic Adhesive DP-810. Technical Data August, 1998
3 Technical Data August, 1998 Product Description 3Mª Scotch-Weldª is a two-part, 1:1 mix ratio, toughened structural adhesive with less odor than most acrylic adhesives. Adhesive has excellent shear and
More informationAradur 76 Hardener. Advanced Materials. Technical Datasheet. Product Description. Applications. Features. Typical Properties*
Aradur 76 Hardener Product Description Aradur 76 Hardener is a formulated polyetherpolyamine hardener suitable for the formulation of crack bridging systems and flexible membranes used in civil engineering
More informationCoatOSil* 7001E. Page 1 of 7. *CoatOSil is a trademark of Momentive Performance Materials Inc Technical Data Sheet.
Technical Data Sheet Description CoatOSil 7001 copolymer is an additive for improved flow and leveling of solventborne two-component acrylic-polyol isocyanate cured coatings. When CoatOSil 7001 copolymer
More informationPerformance Minerals Extenders. For Coatings and Inks
Performance Minerals Extenders For Coatings and Inks BASF Performance Minerals Enhance Coatings and Inks In addition to being the world's leading chemical company, BASF is also a world-leader in surface
More informationSyl-Off Emulsion, Platinum-Catalyzed Silicone Release Coatings from Dow Corning
Syl-Off Emulsion, Platinum-Catalyzed Silicone Release Coatings from Dow Corning Release System Information Guide Features Low silicone coat weights possible A wide range of substrates possible Cured coatings
More informationAdhesion Promoter/Primer 3M Adhesion Promoter AP596
Adhesion Promoter/ 3M Adhesion Promoter AP596 3M All Purpose P591 3M Metal P592 Technical Data October 2017 Product Description 3M Adhesion Promoter AP596 and 3M s P591, P592, and are low viscosity adhesion
More informationK-FLEX Polyester Diol Selection Guide For High Performance VOC Compliant Coatings
SPECIALTY CHEMICALS Polyester Diol Selection Guide For High Performance VOC Compliant Coatings Formulating High Solids Coatings 100% active polyester diols are used primarily as modifiers for acrylic,
More informationRed Insulating Varnish 4228 Technical Data Sheet 4228-Liquid
Description Our 4228 Red Insulating Varnish is a highly insulating coating with excellent arc and corona resistance. This low viscosity, one part varnish coating is easy to use and adheres well to many
More informationTyzor. Application Guide. Innovation isn t just what we do. It s who we are. TM
Tyzor Application Guide It s who we are. Tyzor Application Guide Extensive product information is available on our web site at www.dorfketal.com = PRIMARY CHOICE = SECONDARY CHOICE Dorf Ketal s Tyzor compounds
More informationSafety Data Sheet Xelorex F 3000 Revision date : 2018/10/12 Page: 1/9
Revision date : 2018/10/12 Page: 1/9 1. Identification Product identifier used on the label Recommended use of the chemical and restriction on use Recommended use*: fiber mix change / filler increase *
More informationSimalfa 308fR. Product Description. Features and Benefits. Physical Properties
Revised: 12.12.2013 Simalfa 308fR Product Description Simalfa 308FR was designed specifically for the aerospace industry where the need for specialty flame retardant products are required. This adhesive
More informationDOWSIL and XIAMETER brand Silicone Release Agents
Chemical and Industrial Manufacturing Consumer Solutions DOWSIL and XIAMETER brand Silicone Release Agents Product Performance Features Product Paintability High Temperature (>150 C) Dilution Stability
More informationRHOPLEX SG-10M 100% Acrylic Emulsion For Interior/Exterior Semigloss Latex Paints
Technical Data Sheet RHOPLEX SG-10M 100% Acrylic Emulsion For Interior/Exterior Semigloss Latex Paints Introduction RHOPLEX SG-10M Acrylic Emulsion is a versatile 100% copolymer that was designed for use
More informationSafety Data Sheet Pluronic PE 8100 Revision date : 2018/10/04 Page: 1/9
Revision date : 2018/10/04 Page: 1/9 1. Identification Product identifier used on the label Recommended use of the chemical and restriction on use Recommended use*: Intermediate Recommended use*: Chemical
More informationPharma & Food Solutions. ETHOCEL One of the Few Water-Insoluble Polymers Approved for Global Pharmaceutical Applications
Pharma & Food Solutions ETHOCEL One of the Few Water-Insoluble Polymers Approved for Global Pharmaceutical Applications ETHOCEL Premium Polymers are essentially tasteless, colorless, odorless, noncaloric
More informationARALDITE AW 136 Resin Hardener HY 5049 EPOXY LAMINATING ADHESIVE
ARALDITE AW 136 Resin Hardener HY 5049 EPOXY LAMINATING ADHESIVE DESCRIPTION: Araldite AW 136 resin/hardener HY 5049 epoxy adhesive is a two-part laminating system used for fabricating skis, snowboards
More informationSafety Data Sheet Beta-Carotene 20% DC Revision date : 2017/01/27 Page: 1/9
Revision date : 2017/01/27 Page: 1/9 1. Identification Product identifier used on the label Recommended use of the chemical and restriction on use Recommended use*: food additive(s) * The Recommended use
More informationENCOR Flex 192 Modified acrylic latex for general purpose elastomeric coatings and specialty roof coatings
ARKEMA COATING RESINS ENCOR Flex Modified acrylic latex for general purpose elastomeric coatings and specialty Product Description Polymer Design Performance Benefits Typical Properties 1 ENCOR Flex is
More informationPolypropylene Label Material 7776
Polypropylene Label Material Technical Data March 2012 Product Description 3M Polypropylene Label Material is a durable polypropylene label stock that offers excellent performance in applications requiring
More information3 Scotchmate TM. Nylon Reclosable Fasteners. Technical Data December, Plainbacked Products. Products
3 Technical Data December, 2001 Products Plainbacked Products Loop Hook SJ-3401 SJ-3402 SJ-3418 SJ-3419 Pressure Sensitive Adhesive Products Loop Hook SJ-3518 SJ-3519 SJ-3523 SJ-3522 SJ-3527 SJ-3526 SJ-3571
More informationViscosity, 25 C. Mn, g/mol. Wingtack
Wingtack 10 A Unique Liquid Tackifying Resin Benefits Tackifying hydrocarbon resin Low-color liquid resin Broad compatibility Polymeric plasticization Enhanced flexibility Low-temperature tack and adhesion
More informationPERMABOND HH190 High Strength, High Viscosity Anaerobic Gasketmaker
PERMABOND HH190 High Strength, High Viscosity Anaerobic Gasketmaker Ref #: 022708PBHH190 TYPICAL APPLICATIONS General Maintenance Flange sealant Replaces traditional, pre-cut gaskets General Assembly Non-sag,
More information5015 PU Surfacer Grey
TECHNICAL DATA SHEET Product Description 5455/1235 is a two component, polyurethane filler, designed to improve the appearance of pretreated aluminium pressings and composites. Excellent flexibility Water
More informationPOLYTONE. P Series/Rosin Modified Phenolic Resin POLYOLS & POLYMERS PVT. LTD.
POLYTONE P Series/Rosin Modified Phenolic Resin POLYOLS & POLYMERS PVT. LTD. REGD. OFFICE & WORKS -1 (VAPI): C-1/58-59, G.I.D.C. VAPI 396 195 INDIA info@polyolsandpolymers.net WORKS -2 (DAHEJ) D-2/CH-266-268-269
More informationDOW CORNING MB Masterbatch
Product Information DOW CORNING MB50 001 Masterbatch FEATURES Imparts processing improvements and modified surface characteristics BENEFITS Improved throughput Reduced energy consumption Enhanced scratch
More informationPolymeric Hyperdispersants for Multi Media Colourants
Polymeric Hyperdispersants for Multi Media Colourants MARK SUDDER ASEFAPI 2017 WHAT WE ADD MAKES THE DIFFERENCE ṬM The Lubrizol Corporation 2017, All Rights Reserved. SOLSPERSE HYPERDISPERSANTS Current
More informationNovel Energy-Curable Polyurethane Dispersion with High Formulation Versatility
Novel Energy-Curable Polyurethane Dispersion with High Formulation Versatility Introduction Authors Jason Ghaderi, Xavier Deruyttere, Claire-Sophie Bernet, Colette Moulaert, Jean-Yves Salviato and Michel
More informationNEROX 510 Carbon Black Pigments for Industrial Coatings. Technical Information TI 1392
NEROX 0 Carbon Black Pigments for Industrial Coatings Technical Information TI 92 Introduction For applications in the industrial coatings industry, there is growing demand for black pigments that provide
More informationProduct Information Personal Care Dow Corning 9040 Silicone Elastomer Blend
Product Information Personal Care Dow Corning 9040 Silicone Elastomer Blend FEATURES Compatible with a variety of lipophilic active ingredients such as fragrances, sunscreens, vitamins, and vitamin derivatives
More informationSafety Data Sheet SONOLASTIC 150 VLM TECH LIMESTONE Revision date : 2009/08/26 Page: 1/6
Revision date : 2009/08/26 Page: 1/6 1. Product and Company Identification Company BASF CANADA 100 Milverton Drive Mississauga, ON L5R 4H1 24 Hour Emergency Response Information CANUTEC (reverse charges):
More informationARALDITE 420 A/B Two component epoxy adhesive system
Advanced Materials Araldite 420 A/B Structural Adhesives ARALDITE 420 A/B Two component epoxy adhesive system Key properties Very high lap shear and peel strength Bonds a wide variety of materials (metal,
More informationSole carrier with universal application Licocene for
Sole carrier with universal application Licocene for MASTERBATCH Made to fulfill your requirements Licocene PP 1302 Licocene PP 1502 Licocene PP 2602 Licocene PP 3602 TP* Licocene PP 6102 Clariant s high-performance
More information3M Bumpon Protective Products
Technical Data February 2012 M Bumpon Protective Products Product Description M Bumpon Protective Product series are resilient 70 durometer clear polyurethane rollstock products utilizing an aggressive
More informationElvacite 2823 Acrylic Resin for low VOC
Elvacite 2823 Acrylic Resin for low VOC Acrylic Resin Elvacite 2823 is a methyl methacrylate copolymer designed for use in VOC compliant coatings. Elvacite 2823 utilizes patented technology to provide
More information3M Scotchkote Abrasion Resistance Epoxy Coating 328
3M Scotchkote Abrasion Resistance Epoxy Coating 328 Information, Properties and Test Result June 2015 80-6111-8616-6-A 3 Table of Contents PAGE 1.0 Introduction...1 2.0 Description...1 3.0 Process and
More informationCREATING TOMORROW S SOLUTIONS ADHESIVES & SEALANTS I POLYMER BINDERS I LATIN AMERICA PRODUCT OVERVIEW VINNAPAS AND VINNOL DISPERSIONS
CREATING TMRRW S SLUTINS ADHESIVES & SEALANTS I PLYMER BINDERS I LATIN AMERICA PRDUCT VERVIEW VINNAPAS AND VINNL DISPERSINS MAKE THE MVE T VINNAPAS VAE: THE HIGH-PERFRMANCE SLUTIN Success in the adhesives
More informationProduct Information Plastics Dow Corning MB Masterbatch
Product Information Plastics Dow Corning MB50-001 Masterbatch FEATURES & BENEFITS Imparts processing improvements and modified surface characteristics Improved throughput Reduced energy consumption Enhanced
More informationProduct Information Personal Care Dow Corning 9040 Silicone Elastomer Blend
Product Information Personal Care Dow Corning 9040 Silicone Elastomer Blend FEATURES & BENEFITS Compatible with a variety of lipophilic active ingredients such as fragrances, sunscreens, vitamins, and
More information3 Scotch-Weld TM. Bulk Adhesives. General Purpose 60 CA Hi-Strength Laminating 92 Hi-Strength Post-forming 94 CA. Technical Data May, 2008
3 Scotch-Weld TM General Purpose 60 CA Hi-Strength Laminating 92 Hi-Strength Post-forming 94 CA Bulk Adhesives Technical Data May, 2008 Product Description 3M Scotch-Weld Bulk Adhesives are industrial
More informationNominal Value Unit Test Method. Typical Value Unit Test Method 20 UTM nd
UNIPLEX 280CG UNIPLEX 280CG is a stable, clear, odorless, and non-crystalline brittle solid with a sharp softening range starting at around 93 C. It has excellent ultraviolet light stability. UNIPLEX 280CG
More informationSPUR+* 1015LM. Technical Data Sheet SPUR+* 1015LM
Technical Data Sheet SPUR+* 1015LM SPUR+* 1015LM Description SPUR + 1015LM prepolymer is a silylated polyurethane resin for manufacturing one-part, moisture-curing sealants and adhesives. Plasticizer-free
More information4411N 4411G 4412N 4412G
Extreme Sealing Tape Technical Data October, 2011 Product Description 3M Extreme Sealing Tape is a family of single coated, pressure sensitive adhesive tapes designed for difficult sealing applications.
More information