THE FASTEST WAY TO JOIN HDPE PIPE NO IFS, ANDS, OR BUTTS.

Transcription

1 THE FASTEST WAY TO JOIN HDPE PIPE NO IFS, ANDS, OR BUTTS.

2 HOUSING BOLT/NUT STAINLESS STEEL TEETH GASKET STAINLESS STEEL TEETH ENGINEERED PB-234 REV G

3 PIPE JOINING TECHNOLOGY HOW DOES IT WORK? SMALL DIAMETER Dual rows of stainless steel teeth engage into the outside diameter of plain end HDPE as coupling housing halves are tightened bolt pad to bolt pad, allowing for visual confirmation of correct assembly. LARGE DIAMETER Coupling keys engage into double grooved HDPE pipe as coupling housing halves are tightened bolt pad to bolt pad, allowing for visual confirmation of correct assembly. TOUGH DESIGNED FOR BURIED, SUBMERGED, OR ABOVE GROUND APPLICATIONS refuse-to-fuse.com 1 PB-234 REV G

4 FORGET FUSION LUBE PUSH INSTALLS UP TO 10 FASTER Join HDPE pipe in half the time it takes to fuse a joint. Forget the fusion equipment. Gone are the days of waiting for plastic to heat up just to cool down. Installing in tight or vertical spaces has never been easier; the Refuse-to-Fuse system goes where no fusion machine has gone before. That's time savings you've never seen before. INSTALLATION IS WEATHER INDEPENDENT Whether it's rain, shine, or just downright frigid and fierce, Refuse-to-Fuse products can be installed. No need to check the weather forecast and worry about protection for fusion equipment or project delays any longer. 2 PB-234 REV G

5 HDPE joints completed per hour on 4" SDR 11 HDPE pipe Electrofusion 1.3 Flanging 2.5 Butt Fusion 6 Mechanical Coupling 20 WITH THIS COUPLING, IT S SO EASY... JUST MARK THE DEPTH, SLIDE THE PIPE IN AND TIGHTEN IT UP... MUCH FASTER THAN FUSING. Dave, Stone Hill Contracting JOIN TIGHTEN MEETS OR EXCEEDS PRESSURE RATINGS OF HDPE PIPE If you thought your fused joint was tough, check out Refuse-to-Fuse product performance. Small diameter solutions call for dual rows of razor-sharp teeth that sink into the O.D. of HDPE pipe, forming a sealed hold that never lets go. Bringing out the big guns? Large diameter solutions enlist a rugged double groove to seal the deal. Push it, pull it, and drag it to the max; treat it the same way you would treat fused pipe. INSTALLS WITH SIMPLE TOOLS No need to set up your fancy fusion machine because all you will need with the Refuse-to-Fuse system is a simple socket wrench. If you want to get crazy, a cordless impact driver will do the job, too! Don t worry about training certificates or learning how to use fusion equipment, just stick with the basics. refuse-to-fuse.com 3 PB-234 REV G

6 SMALL DIAMETER INSTALLATION- READY Installation-Ready Refuse-to-Fuse Coupling for Plain End HDPE Pipe STYLE 905 Download publication for complete information Designed for plain end HDPE pipe (SDR 7 SDR 21) Sizes from 2 8" IPS and mm ISO Certifications/Listings: WaterMark Download publication for complete information 4 PB-234 REV G

7 INSTALLATION- READY Refuse-to-Fuse Transition Coupling for HDPE-to-Steel Pipe STYLE 907 Download publication for complete information Designed to provide a single transition from plain end HDPE pipe (SDR 7 SDR 21) to grooved steel sized piping system components Certifications/Listings: Sizes from 2 8" IPS HDPE to 2 8" DN50 DN200 grooved steel Sizes from mm ISO HDPE to 2 8" DN50 DN200 grooved steel WaterMark Download publication for complete information INSTALLATION- READY Installation-Ready Refuse-to-Fuse Flange Adapter for HDPE-to- Flanged Pipe STYLE 904 Download publication for complete information Designed to provide a single transition from plain end HDPE pipe (SDR 7 SDR 21) to flanged piping system components Sizes from 3 8" IPS HDPE to 3 8" IPS ANSI Class 150 Flange Refuse-to-Fuse Fittings for HDPE Pipe Download publication for complete information Available in SDR 7, SDR 11, and SDR 17 Sizes from 2 8" IPS and mm ISO Full flow fittings Compatible for use with Style 905 and 907 HDPE couplings No. H10 90 Elbow No. H11 45 Elbow No. H20 Tee No. H50 Reducer refuse-to-fuse.com 5 PB-234 REV G

8 LARGE DIAMETER 6 PB-234 REV G

9 Refuse-to-Fuse Coupling for Double-Grooved HDPE Pipe STYLE 908 Download publication for complete information Designed for double grooved HDPE (SDR 7 SDR 21) Sizes from 8 36" IPS and mm ISO Larger diameter couplings have lifting lugs for easy maneuvering around the job site Certifications/Listings: Standard Victaulic coupling assembly procedure used for installation WaterMark Download publication for complete information Mechanical-T Spigot Outlet STYLE 926 Download publication for complete information Designed to provide an outlet connection on HDPE, steel, and ductile iron pipe materials in IPS, ISO, and AWWA pipe sizes 4" outlets available for 10 32" IPS pipe diameters mm outlets available for mm ISO pipe diameters 6" outlets available for 16 48" IPS pipe diameters mm outlets available for mm ISO pipe diameters Refuse-to-Fuse Cut Grooving Tool for HDPE Pipe CG " IPS mm ISO CG " IPS mm ISO CG " IPS mm ISO Download publication for complete information Designed for cut grooving HDPE (SDR 7 SDR 21) pipe Provides the only grooved joining solution for large diameter HDPE pipe Faces and cuts parallel grooves into the end of the pipe WEATHER INDEPENDENT LIGHTWEIGHT PORTABLE SMALL FOOTPRINT refuse-to-fuse.com 7 PB-234 REV G

10 CASE STUDY ATLAS RESOURCES HAMMAN SALT WATER DISPOSAL In June 2015, construction was completed at the Atlas Resources Hamman salt water disposal (SWD) facility in Jacksboro, Texas. The Hamman facility is comprised of ten water tanks, two oil tanks, one gun barrel, and three offload stations. Prior to its commencement, the project s contractor knew the job would be laden with challenges associated with joining HDPE pipe while facing construction schedule constraints. 8 PB-234 REV G

11 PROJECT Type of Facility: Salt Water Disposal Victaulic Solutions: Construction Piping Services Ease and Speed of Installation Installation Time Savings Prefabrication Owner: Atlas Resources Contractor: Black Sheep Engineer/Consultant: Atlas Resources Fusing HDPE pipe would be an unfavorable option because of its extremely time-consuming nature. Additionally, fusion would require good weather conditions in order to allow for proper mending of fusion welds. Prefabrication options and new Victaulic HDPE products boasted several attractive benefits, including controlled costs and a dramatic improvement on the SWD facility s completion date. Victaulic was able to provide a hard number for the prefabrication piece of the project and presented the new Style 908, Style 907, and Style 905 HDPE couplings as a way to finish the job in just 3 4 weeks, according to Atlas Resources personnel. During the first week of assembly, the job site was hit with high winds and 11 13" cm of rain. Fortunately, thanks to Victaulic, construction was able to remain on schedule, with the prefabricated portion finishing in 6 days and the offload station and additional piping finishing in 10 days. The easy-to-install Victaulic HDPE couplings were the ideal solution to deal with heavy rain and wet conditions, especially when compared with HDPE fusion. After successfully overcoming various challenges by using Victaulic HDPE solutions, the Hamman facility was recognized by the Plastic Pipe Institute (PPI) and received the 2016 Energy Piping Systems Division Project of the Year award. SPECIFICATIONS Services: Pipe Materials: Pipe Size Range: Gun Barrel Piping SDR 9 HDPE 10" IPS Offload Station SDR 9 HDPE 4 6" IPS Tank Manifold Piping SDR 9 HDPE 8 10" IPS Oil Carbon Steel 2 4" IPS refuse-to-fuse.com 9 PB-234 REV G

12 North and South America Europe, Middle East, Africa and India Asia Pacific UNITED STATES AND WORLD HEADQUARTERS BELGIUM EUROPE HEADQUARTERS CHINA 4901 Kesslersville Road Easton, PA USA Prijkelstraat Nazareth, Belgium PICK VIC (within North America) pickvic@victaulic.com (within Germany) viceuro@victaulic.com UNITED KINGDOM CANADA 123 Newkirk Road Richmond Hill Ontario L4C 3G5 Canada Units B1 & B2, SG1 Industrial Park Cockerell Close, Gunnels Wood Road Stevenage, Hertfordshire, UK SG 1 2NB viccanada@victaulic.com viceuro@victaulic.com MEXICO UNITED ARAB EMIRATES Calle Circuito del Marqués No 8 al 11 Parque Industrial El Marqués Municipio El Marqués Queretaro, Mexico CP FZ LIU10 AA01, AA02, AA03, AA04 and AA05 Al Munawala Street Jebel Ali Freezone Southzone PO BOX Jebel Ali, Dubai UAE-United Arab Emirates vical@victaulic.com viceuro@victaulic.com BRAZIL Av. Marquês de São Vicente 446 Cj 1303 Várzea da Barra Funda São Paulo-SP CEP Brazil vicbr@victaulic.com INDIA India Land Global Industrial Park Plot 4, Hinjewadi, Phase-1, Mulshi Pune , India Unit 808, Building B Hongwell International Plaza No.1602 West Zhongshan Road Shanghai, China vicap@victaulic.com KOREA 4F, Seoil Building, , Seocho-Dong, Seocho-Gu Seoul, Korea vicap@victaulic.com TAIWAN No. 55, NanGong Rd, LuZhu District TaoYuan City 338, Taiwan vicap@victaulic.com AUSTRALIA AND NEW ZEALAND 7 Chambers Road Unit 1 Altona North, Victoria Australia PIC VIC (within Australia) PICK VIC (within New Zealand) viceuro@victaulic.com vicaust@victaulic.com For additional locations, information and support, visit refuse-to-fuse.com PB REV G 09/2017 Victaulic and all other Victaulic marks are the trademarks or registered trademarks of Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries. All other trademarks listed herein are the property of their respective holders, in the U.S. and/or other countries. The terms Patented or Patent Pending refer to design or utility patents or patent applications for articles and/or methods of use in the United States and/or other countries VICTAULIC COMPANY. ALL RIGHTS RESERVED.