Trimform for panels, purlins & gutters. No obligation consultation

Transcription

1 Trimform for panels, purlins & gutters. No obligation consultation Vers 1:02/2016

2 Trimform Insulated Panels Trimform insulated panels consist of two coated steel profile bonded to a core of PIR insulation; they may be used to form roofs, down to a 4º pitch, and walls. The system includes a comprehensive range of guttering, flashings, sealants and rooflights. The Trimform system offers rapid coverage and swift completion of a weatherproof building envelope to give a high performance building. Composition Trimform insulated panels consist of a core of polyisocyanurate (PIR) insulation sandwiched between a heavily profiled external weather sheet and an internal shallow profiled liner. The PIR insulation bonds to the steel sheets during the manufacturing process, together the insulation and steel form strong, rigid panels with good thermal performance. Trimform roof and wall panels are manufactured in a process certified to ISO 9001:2008. Trimform roof and wall panels have been tested by the Loss Prevention Certification Board and comply with the requirements of LPS 1181:2005. Part 1 Issue 1.1: Series of Fire Growth Tests for LPCB Approval and Listing of Construction Product Systems Part 1: Requirements and Tests for Built-Up Cladding and Sandwich Panel Systems for Use as the External Envelope of Buildings. Fixing details for roof and wall panels Thermal The PIR insulation within Trimform insulated panels has a low thermal conductivity that gives the panels their good thermal performance. The large panel dimensions and the edge lap seals give Trimform insulated panel systems good resistance to air leakage. U-values: Trimform Insulated Panels Panel thickness U-value* (W/m2K) U values determined using finite element analysis to BS EN ISO 10211:2007. Due to changing regulatory requirements details and panel thicknesses available may change. Contact Trimform Technical Service for further details.

3 Structure Trimform insulated panels are designed to be supported by and fixed to steel or timber purlins. Steelwork for insulated panels should be within the tolerances given in BS EN :2008 +A1:2011: fixing planes on adjacent purlins should be less than L/600 apart (where L is the purlin spacing). All Trimform insulated panels are suitable for spanning purlins at 1.8m centres. Consult our Technical Department for guidance on using the panels on purlins at centres greater than 1.8m. Trimform insulated panels should be isolated from preservative treated timber purlins by PVC barrier tape applied to the bearing face of the purlins. Whilst panels may be fixed through valleys or crowns, Trimform recommend valley fixing: accurate fixing is easier to achieve, loads on the fixings are smaller, the fixings are less likely to distort the weather sheet, and better compression of the sealant is achieved at end laps. Fixings should be stainless steel or carbon-steel self drilling screws with a high thread to restrain the weather face of the panel and should have press-on or integral caps to match the finish of the panel. To prevent water penetration each fixing should have a 19mm diameter EPDM washer. Performance LPCB ref. no Fire resistance results to LPS 1181:2005 Panel Thickness (mm) Fire resistance (minutes) integrity (BS :1987) 635a/08 Trimform/1000 Roof panels 40, 60, 70, 80, 100, 110, 120 & a/09 Trimform/1000 Wall panels 60, 80, 100, 115, 120 & 130 Fire resistance (minutes) insulation (BS :1987) Grade Core N/A N/A EXT-8 HCFC-free PIR EXT-A15 HCFC-free PIR Wall panels covered by LPCB reference 635a/04 and 635a/05 must be laid vertically. Wall panels require external side lap stitching at 300mm centres. Roof panels require external side lap stitching at 450mm centres. Roof and wall panels covered by LPCB certificates 635a/04 and 635a/05 require a 6mm x 5mm NFRC Class A butyl tape to be used in the side lap joints. Contact Trimform s Technical Department for information on fire rated panels.

4 Steadman Purlins and Rails Butted single span purlin system The system is required for buildings of a single span length and is efficient for short spans or light loadings. Butted purlins are also useful for frames which have large clear spans and where large frame deflections may be harmful to continuous purlin systems. Butted purlins can be used over supports or within the depth of the supporting section. Maximum span is 11.4m. Butted purlin system This system is useful for single-span conditions, either oversupports or flush with supports. The system is also economical for small bays or light loadings, where sleeves are not necessary. Zed & Cee profile dimensions Butted Connection Butted Connection with inset cleat for flush construction Section Depth Dimensions in mm Zeds Cees A B C D E F 140, Cladding System Slope Roof Roof Sag System Details Metal Cladding (restraining type) Metal Cladding (non-restraining type) < 4.6m span 4.6m - 7.6m span 7.6m m span < 3 1 row angle braces 2 rows angle braces rows 1 row bars 2 row bars row angle braces + diagonals 2 rows angle braces + diagonals < row angle braces 2 rows angle braces 5-35 row angle braces + diagonals 2 rows angle braces + diagonals Hook-bolt (restraining type) < 3 Not recommended row bars 2 row bars row angle braces + diagonals 2 rows angle braces + diagonals Single/double span lengths This system may be used with restraining or non-restraining cladding, and may also be used to support tiled roof systems. The system may require to be used in conjunction with sag-systems. Consideration should be given to handling and erection sequence when utilising the double-span section. Double Span Connection Sleeved Connection

5 Trimform for every product you need With over 20 years experience, Trimform are proud to be one of the UK s leading manufacturers of architectural products in a wide variety of finishes, colours and profiles. This even includes bespoke components produced to an architect s or specifier s exact requirements. Trimform Gutters Trimform manufactures bespoke architectural fabrications and flashings in aluminium, steel and other metals to a customer s design. 2D and 3D shapes are formed by pressing, folding, punching and welding in pre-coated or post-coated materials. Fabrications are not limited to use in building and construction only if it can be fabricated from metal, Trimform can make it. Eaves Gutters Trimline eaves and box eaves gutters are produced from pre-coated steel and pre-coated or post coated aluminium, complete with stopends, hopper heads, butt straps, sealants, fasteners and downpipes. Trimline and other gutters are manufactured to order to the customer s dimensions. Membrane lined Insulated Gutters Trimform membrane lined gutters create a fully sealed gutter system and are the ideal solution for rainwater management. Using a range of market leading materials such as IKO Armourplan PVC and Tata Aquatite, the gutters have a 1.2mm membrane weathering, integral insulation, a galvanised or white polyester painted steel lining, and are fabricated to order for valley, boundary wall and parapet gutter applications. Stopends, corner sections, outlets, sumps and downpipes are available to order.

6 If you d like to know more about of any of our products or services, contact us using the details below. One of our team will be happy to help in any way. Tel: Fax: info@trimformfabs.co.uk Website: trimformfabs.co.uk Trimform Products (A trading division of SIG Trading Limited) Harding Way, Somersham Road, St. Ives, Huntingdon, Cambridgeshire, PE27 3WR.