Technical properties Précontraint 1302 S2 Standards Surface treatment (top/back)

Transcription

1 S2

2 Technical properties Précontraint 1302 S2 Standards Surface treatment (top/back) S2 PVDF / PVDF Yarn PES HT 1100/2200 Dtex Weight 1350 g/sqm 39.8 oz/sqyd EN ISO Width 267 cm in (+1mm /-1mm) Tensile strength (warp/weft) Tear resistance (warp/weft) 800/700 dan/5cm 900/800 lbs/in 120/110 dan 200/180 lbs EN ISO 1421 ASTM D Cut Strip DIN ASTM D Trapezoid Adhesion 13 dan/5cm EN ISO 2411 Flame retardancy Euroclass C-s2,d0/EN Rating B1/DIN BS 7837 Test2/NFPA 701 CSMF T19 Guarantee* > The technical data here above are average values with a +/-5% tolerance Longevity Total thickness 1.02 mm Coating thickness at the top of the yarns 250 microns Varnish adhesion longevity QUV A 4000 h pass Scotch tape test Solar optical values ASHRAE EN 410 Solar Transmittance (Ts) 5% 4.5% Solar reflectance (Rs) 76% 78% Solar Factor (g) 10% 8.5% Visible light Transmittance (Tv) -- 3% Visible light Reflectance (Rv) -- 86% UV transmittance 0% Global thermal conductivity** Vertical / Horizontal position U= 5.6 / 6.4 W/sqm/ C Acoustic performance Weakening index 15dBA ISO LEED Heat island Effect Roof / Non roof (up to 1 pt/ 2 pts) Solar Reflectance Index >95% SSc 7.2/SSc 7.1 Environmental Impact: LCA (Life Cycle Assessment) ISO Comparative analysis depending on end-of-life scenarios Global warming Kilograms eq. CO 2 Energy consumption Megajoul eq. Water consumption Litre Management systems Quality in conformity with ISO 9001 Environmental communication in conformity with ISO Certifications, labels, recycling capacity LCA and LEED reports available on request Texyloop Recycling Incineration Landfill Functional unit = 1 sqm Material only / 1302 S2 values Précontraint is a Serge Ferrari registered trade mark. ref DECEMBRE 2015/ V1.01 GB > The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please refer to the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. ** Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover photo: Metro Station, Santiago (Chile) Serge Ferrari

3 S2

4 Technical properties Précontraint 1502 S2 Standards Surface treatment (top/back) S2 PVDF / PVDF Yarn PES HT 1670/2200 Dtex Weight 1500 g/sqm 44.2 oz/sqyd EN ISO Width 180 cm in (+1mm /-1mm) Tensile strength (warp/weft) Tear resistance (warp/weft) 1000/800 dan/5cm 1150/900 lbs/in 160/140 dan 350/250 lbs EN ISO 1421 ASTM D Cut Strip DIN ASTM D Trapezoid Adhesion 15 dan/5cm EN ISO 2411 Flame retardancy Euroclass C-s2,d0/EN Rating B1/DIN BS 7837 CSMF T19 Guarantee* > The technical data here above are average values with a +/-5% tolerance Longevity Total thickness 1.14 mm Coating thickness at the top of the yarns 200 microns Varnish adhesion longevity QUV A 4000 h pass Scotch tape test Solar optical values ASHRAE EN 410 Solar Transmittance (Ts) 4% 4% Solar reflectance (Rs) 76% 81% Solar Factor (g) 9% 8% Visible light Transmittance (Tv) % Visible light Reflectance (Rv) -- 89% UV transmittance 0% Global thermal conductivity** Vertical / Horizontal position U= 5.6 / 6.4 W/sqm/ C Acoustic performance Weakening index 16dBA ISO LEED Heat island Effect Roof / Non roof (up to 1 pt/2 pts) Solar Reflectance Index >95% SSc 7.2/SSc 7.1 Environmental Impact: LCA (Life Cycle Assessment) ISO Comparative analysis depending on end-of-life scenarios Global warming Kilograms eq. CO 2 Energy consumption Megajoul eq. Water consumption Litre Management systems Quality in conformity with ISO 9001 Environmental communication in conformity with ISO Certifications, labels, recycling capacity LCA and LEED reports available on request Texyloop Recycling Incineration Landfill Functional unit = 1 sqm Material only / 1502 S2 values Précontraint is a Serge Ferrari registered trade mark. ref DECEMBRE 2015/ V1.01 GB > The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please refer to the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. ** Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover photo: Zayed University, Abu Dhabi (UAE) Serge Ferrari

5 S2

6 Technical properties Précontraint 1002 S2 Standards Surface treatment (top/back) S2 PVDF / PVDF Yarn PES HT 1100 Dtex Weight 1050 g/sqm 31 oz/sqyd EN ISO Width 267 cm in (+1mm /-1mm) Tensile strength (warp/weft) Tear resistance (warp/weft) 420/400 dan/5cm 480/450 Lbs/in 55/50 dan 80/75 Lbs EN ISO 1421 ASTM D Cut Strip DIN ASTM D Trapezoid Adhesion 12 dan/5cm EN ISO 2411 Flame retardancy Euroclass B-s2,d0/EN Rating M2/NFP B1/DIN BS 7837 Test2/NFPA 701 CSMF T19 Guarantee* > The technical data here above are average values with a +/-5% tolerance. ADDITIONAL INFORMATION Total thickness 0.78 mm Coating thickness at the top of the yarns 200 microns Varnish adhesion longevity QUV A 4000 h pass Scotch tape test Dimensional stability Elongation 24h -10daN/5cm (warp/weft) <1% / <1% EN Residual elongation <0.4% / <0.4% EN Solar optical values ASHRAE EN 410 Solar Transmittance (Ts) 6% 5.5% Solar reflectance (Rs) 78% 81.5% Solar Factor (g) 12% 9% Visible light Transmittance (Tv) -- 4 % UV transmission 0% Thermal and Acoustic performances Thermal conductivity (vertical/horizontal) ca. U=5.6 / 6.4 W/sqm/ C Calculated Acoustic Weakening index ca. 14dBA ISO LEED Heat island Effect Roof / Non Roof (up to 1 pt/2 pts) Solar Reflectance Index >95% SSc 7.2/SSc 7.1 Environmental Impact: LCA (Life Cycle Assessment) ISO Depending on end-of-life scenarios Texyloop Recycling Incineration Landfill 1 sqm membrane 1002 S2 Global warming Kilograms eq. CO2 Energy consumption Megajoul eq. Water consumption Litre Management systems Quality in conformity with ISO 9001 Environmental communication in conformity with ISO Certifications, labels, recycling capacity Précontraint is a Serge Ferrari registered trade mark / DECEMBRE 2015/ V1.01 GB LCA and LEED reports available on request > Additional information here above are non-contractual. The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please refer to the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources

7 S2

8 Technical properties Précontraint 1202 S2 Standards Surface treatment (top/back) S2 PVDF / PVDF Yarn PES HT 1100/1670 Dtex Weight 1050 g/sqm 31 oz/sqyd EN ISO Width 267 cm in (+1mm /-1mm) Tensile strength (warp/weft) Tear resistance (warp/weft) 560/560 dan/5cm 630/630 lbs/in 80/65 dan 130/100 lbs EN ISO 1421 ASTM D Cut Strip DIN ASTM D Trapezoid Adhesion 12 dan/5cm EN ISO 2411 Flame retardancy Euroclass B-s2,d0/EN Rating B1/DIN BS 7837 Test2/NFPA 701 CSMF T19 Guarantee* > The technical data here above are average values with a +/-5% tolerance Longevity Total thickness 0.78 mm Coating thickness at the top of the yarns 200 microns Varnish adhesion longevity QUV A 4000 h pass Scotch tape test Solar optical values ASHRAE EN 410 Solar Transmittance (Ts) 6% 6% Solar reflectance (Rs) 75% 80% Solar Factor (g) 11% 10% Visible light Transmittance (Tv) % Visible light Reflectance (Rv) -- 88% UV transmission 0% Global thermal conductivity** Vertical / Horizontal position U= 5.6 / 6.4 W/sqm/ C Acoustic performance Weakening index 14dBA ISO LEED Heat island Effect Roof/Non roof (up to 1 pt/2 pts) Solar Reflectance Index >95% SSc 7.2/SSc 7.1 Environmental Impact: LCA (Life Cycle Assessment) ISO Comparative analysis depending on end-of-life scenarios Global warming Kilograms eq. CO 2 Energy consumption Megajoul eq. Water consumption Litre Management systems Quality in conformity with ISO 9001 Environmental communication in conformity with ISO Certifications, labels, recycling capacity LCA and LEED reports available on request Texyloop Recycling Incineration Landfill Functional unit = 1 sqm Material only / 1202 S2 values Précontraint is a Serge Ferrari registered trade mark. ref DECEMBRE 2015/V1.01 GB > The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please refer to the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. **Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover photo: Brisbane Airport (Australia) Serge Ferrari

9 Exclusive Précontraint Serge Ferrari technology MAIN FEATURES Satin finish APPLICATIONS Facade blinds, awnings Patented worldwide, Précontraint Serge Ferrari technology involves keeping the composite under tension throughout the manufacturing cycle. Surface treatment Reinforced dirt resistance and easy cleanability Dimensional stability 10 year warranty * Longevity Canopies Velums and pergolas Shade sails Light structures and fixed awnings Technical properties Précontraint 502 SATIN Standards Weight 570 g/m oz/sqyd EN ISO Width 180 cm 70.9" Length of the rolls Standard format length 40 lm yds Physical properties Maximum creativity Tensile strength (warp/weft) 200/200 dan/ 5 cm EN ISO 1421 Tear strength (warp/weft) 20/20 dan DIN High tenacity polyester base cloth Strength characteristics Exceptional dimensional stability Benefits* No deformation; won't sag A unique satin finish to give a modern and high end look to your projects. A palette of 40 colours to give personality to the most varied designs. Flexibility and strength provides total freedom of shape and size. Adhesion 7/7 dan/ 5 cm EN ISO 2411 Surface treatment Finish Flame retardancy Rating PVDF Varnish both sides M2/NFP M2/UNE Method 1 and 2/NFPA 701 CSFMT19 CLASS A/ ASTME84 BS 7837 B1/DIN CLASSE 2/UNI 9177 CAN/ULC-S109 SchwerbrennbarQ1-Tr1/ONORM A /AS/NZS G1/GOST B-s2,d0/EN Long-term strength Greater coating thickness at the top of the yarns Exceptional flatness * Benefits observed for normal product usage To know more Tear resistant Long-term aesthetics and strength Smooth finish, easy maintenance Scan the QR code hereunder to view our video presenting the new Precontraint 502 Satin range! Visit our website for further information: Satin finish compliments current architectural trends Innovation and Performance A weldable PVDF treatment improves dirt resistance A very smooth finish ensures easy upkeep. Protection against heat, inclement weather conditions for your comfort all year long. A maximum UV protection : Precontraint 502 Satin filters 100% of UVB rays (UPF 50+ for all the colours) Euroclass B-s2,d0/ EN Management system for Quality ISO 9001 Certifications, labels, guarantees, recycling capacity The above technical data represent average values subject to a +/-5% tolerance. The buyer of our products is fully responsible for their application and their transformation with regard to any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, workmanship and safety regulations in force in destination countries. For information on our contractual warranty, please refer to the relevant terms and conditions. The values quoted above represent results of tests performed in compliance with common design practices and are provided for information only to enable customers to make the best use of our products. Our products are subject to changes based on technical advances and we reserve the right to modify their characteristics at any time. The buyer of our products is responsible for checking the validity of the above data. TOOLS AND SERVICES Précontraint is a Serge Ferrari registered trademark. Ref JANVIER V1.01 GB Maintenance manual and Life Cycle Assessment (LCA) available on request Aesthetics and comfort that lasts Proven longevity Exceptional long-term mechanical resistance avails the most demanding structures. High UV resistance of colours due to rigorous pigment selection. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover photos: Headquarters - US Interior photos: private house - New Zealand Dolphin Mall, Miami - US Private house - Costa Rica Photos: Serge Ferrari sas Durability and reliability guaranteed by Précontraint Serge Ferrari technology * For static applications

10 Solar and light properties (EN 14501) Reference TS RS AS 502V2-1125C V2-2012C V2-2135C Champagne 502V2-8341C Vanilla 502V2-8861C Hemp 502V C Aniseed 502V2-2157C Olive 502V C Moss green 502V2-2158C 502V2-2137C V2-2138C V2-2141C V2-2148C V2-2150C V2-2152C V2-2156C V2-2157C Sandy beige 502V2-2135C Pepper 502V2-2012C Camel 502V2-2141C Porcelain green 502V C Tennis green 502V2-8056C Spruce 502V2-2156C 502V2-2158C V2-2160C V2-2161C V2-2166C V2-2167C V2-2168C V2-2171C V2-2172C Concrete 502V2-2167C Cocoa 502V2-2148C Teak 502V C Walnut stain 502V2-2137C Celadon 502V C Steel blue 502V C Lagoon 502V2-2160C 502V2-8056C V2-8102C V2-8204C V2-8255C V2-8284C V2-8341C V2-8450C V2-8861C White 502V2-8102C Boulder 502V2-2171C Concrete 502V2-2167C Lemon 502V C Buttercup 502V2-2166C Dijon 502V C Dark blue 502V C Thistle blue 502V C Celestial blue 502V C 502V C V C V C V C V C V C V C V C METALLIC COLOURS Black 502V2-8450C Orange 502V2-8204C Carrot 502V2-2172C Raspberry 502V2-2150C Victoria Blue 502V C Midnight blue 502V2-2161C Marine 502V2-1125C 502V C V C V C V C V C Velvet red 502V2-2152C Automn 502V2-2138C Aluminium 502V2-2168C Poppy 502V2-8255C Terracotta 502V C Burgundy 502V2-8284C TS : Solar Transmission (%) RS : Solar Reflection (%) AS : Solar Absorption (%) TS + RS + AS = 100% of incident energy

11

12 Technical pr oper ties Application Surface treatment Making up Yarn Weight Total thickness Width Tensile strength Iwarp/weft) Tear resistance Iwarp/weft) Adhesion Flame reta rdancy Pnkontraint 702 S2 Mobile or permanent structures PVo F Weldable PES HT 1100 otex 750 g/sqm 22.1 oz/sqyd 0.60 mm cm in 280/280 dan/5cm 320/320 lbs/in 30/28 da N 85/80 l bs 10 dan/5cm Pnkontraint 702 Fluotop T2 Standards Tropical climate, static and permanent structures HIGH CONCENTRATION PV of / PVoF Wel dable after top surface abrasion PES HT 1100 o tex 750 g/sqm 22.1 oz/sqyd 0.56 mm 178 cm in 300/280 da N/5cm 340/320 lbs/in 30/28 da N 85/80 l bs 10 dan/5cm Euroclass B-s2,dO/ EN B- s2,do/ EN Rat ing Guarantee' M2/ N FP B1 / oin BS 7837 Test2/ N FPA 701 CS MF T1 9 EN ISO I+ lmm/-lmm] EN ISO 1421 ASTM Cut Strip DIN ASTM Trapezoid EN ISO 2411 > The technical data here above are average values with a +/-5% tolerance Longevity Coa ting t hickness at t he top of the ya r ns 240 m icro ns 240 m icrons Varn ish adhesion longevity Wh ite color evo lution QU V A4000 h pass QUV A 4000 h lie = 5.5 QUV A 4000 h pass auva4000 h.toe = 3.5 Scotch ta pe test CIE Lab Micro organism resistance" Method A: degree 0, excellent EN ISO 846 Solar optical values ASH RAE EN 41 0 ASH RAE EN410 Solar Transmittance ITs] 8% 8.5% So lar reflectance IRs] Sola r Factor Ig i 74 % 78% 13% 12% 9% 10% 73% 79% 15% 13% ( -'y~si b~ t Transmittance ITvl 6.5% 8% Visi~ht Re flectance IRvl 86% 88% UV transmission Visible light Tra nsmittance ltv] 13.5% 0% 14% 0% N FP Idiffus-diffusl Global thermal conductivity'" Ve rt ica l / Hori zon ta l posit ion U= 5.6 / 6.4 W/sqm/oC U= 5.6/6.4 W/sqmjOC Acoustic performance Weaken ing index 12dBA 12d BA ISO LEEo Heat island Effect Non roo f l up to 2 ptsl Sola r Reflectance Index >95% Roo f l up to 1 pt] Solar Reflectance Index >95% Solar Re flectance Index >9,-5::-o:- Vo --,S:-cS.c 7.1 Sola r Reflectance Index >95% SSc 7.2/GIB C91 Noi Environmental Impact: LCA (Life Cycle Assessment] ISO Co m parative analysis depending Texyloop Incineration Landfill Functional uni t = 1 sqm _o n_ ':."~_- _o f_- life scenarios R_e_c-'-y_c_ling Material on ly /70252 va lues Resources de letion Kilograms eg o Sb Glo bal warming Kilograms eq. CO, En ergy co ns"- um-'-'-p-'- t i-'-0:.;. n 4 1_. 7.-' ~a j o u l eg o Water co nsumption Litre Management systems Quality in conformity w it h ISO 9001 Environmental co m munica t ion in confo r m ity w ith ISO Certifications, l abels, recycling capacity LeA and LE ED repo rts 152 and T2] available on re quest > The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify t he characteristics afour products at anytime. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please referto the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. ** See long term case studies in tropical climate [Longevity & sustainability brochurel. *** Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible fortheir application or their transformation concerning any possible third party. The buyerof our products is responsible fortheir implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources S ~ erge Ferrari

13 S2

14 Technical properties Précontraint 902 S2 Standards Application Mobile or permanent structures Surface treatment (top/back) PVDF / PVDF Making up Weldable Yarn PES HT 1100 Dtex Weight 950 g/sqm 28 oz/sqyd EN ISO Total thickness 0.72 mm Width 267 cm in (+1mm /-1mm) Tensile strength (warp/weft) Tear resistance (warp/weft) 420/400 dan/5cm 480/450 lbs/in 55/50 dan 105/100 lbs EN ISO 1421 ASTM D Cut Strip DIN ASTM D Trapezoid Adhesion 12 dan/5cm EN ISO 2411 Flame retardancy Euroclass B-s2,d0/EN Rating M2/NFP B1/DIN Test 2/NFPA 701 CSMF T19 Guarantee* > The technical data here above are average values with a +/-5% tolerance Longevity Coating thickness at the top of the yarns 300 microns Varnish adhesion longevity QUV A 4000 h pass Scotch tape test Solar optical values ASHRAE EN 410 Solar Transmittance (Ts) 7% 7% Solar reflectance (Rs) 75% 80% ASHRAE Solar Factor (g) 11.5% 12.5% EN 410 Visible light Transmittance (Tv) -- 5% Visible light Reflectance (Rv) -- 88% UV transmission T-UV 0% Visible light Transmittance (Tv) 9% NFP (diffus-diffus) Global thermal conductivity** Vertical / Horizontal position U= 5.6 / 6.4 W/sqm/ C Acoustic performance Weakening index 13dBA ISO LEED Heat island Effect Non roof (up to 2 pts) Solar Reflectance Index >95% SSc 7.1 Roof (up to 1 pt) Solar Reflectance Index >95% SSc 7.2/GIB C9 (ND) Environmental Impact: LCA (Life Cycle Assessment) ISO Comparative analysis depending on end-of-life scenarios Texyloop Recycling Incineration Landfill Functional unit = 1 sqm Material only / 902 S2 values Resources depletion Kilograms eq. Sb Global warming Kilograms eq. CO 2 Energy consumption Megajoul eq. Water consumption Litre Management systems Quality in conformity with ISO 9001 Environmental communication in conformity with ISO Certifications, labels, recycling capacity Précontraint is a Serge Ferrari registered trade mark. ref SEPT 2012/ V1.01 Studio Serge Ferrari GB LCA and LEED reports available on request > The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please refer to the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. ** Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover photo: Stadium - Nelson Oyarzun Arenas - Chile Serge Ferrari Join us facebook.com/sergeferrarigroup

15 S T2

16 Technical properties Précontraint 1502 S2 Précontraint 1502 Fluotop T2 Standards Application Mobile or permanent structures Tropical climate, static and permanent structures Surface treatment (top/back) PVDF / PVDF HIGH CONCENTRATION PVDF / PVDF Making up Weldable Weldable after top surface abrasion Yarn PES HT 1670/2200 Dtex PES HT 1670/2200 Dtex Weight 1500 g/sqm 44.2 oz/sqyd 1500 g/sqm 44.2 oz/sqyd EN ISO Total thickness 1.14 mm 1.14 mm Width 180 cm in 178 cm in (+1mm /-1mm) Tensile strength (warp/weft) Tear resistance (warp/weft) 1000/800 dan/5cm 1150/900 lbs/in 160/140 dan 240/200 lbs 1000/800 dan/5cm 1150/900 lbs/in 160/140 dan 240/200 lbs EN ISO 1421 ASTM D Cut Strip DIN ASTM D Trapezoid Adhesion 15 dan/5cm 15 dan/5cm EN ISO 2411 Flame retardancy Euroclass C-s2,d0/EN C-s2,d0/EN Rating B1/DIN BS 7837 CSMF T19 Guarantee* > The technical data here above are average values with a +/-5% tolerance Longevity Coating thickness at the top of the yarns 300 microns 300 microns Varnish adhesion longevity QUV A 4000 h pass QUV A 4000 h pass Scotch tape test White color evolution QUV A 4000 h ΔE = 5.5 QUV A 4000 h ΔE = 3.5 CIE Lab Micro organism resistance ** -- Method A: degree 0, excellent EN ISO 846-A Solar optical values ASHRAE EN 410 ASHRAE EN 410 Solar Transmittance (Ts) 4% 4% 5% 4% Solar reflectance (Rs) 76% 81% 76% 76% ASHRAE Solar Factor (g) 9% 8% 10% 8% EN 410 Visible light Transmittance (Tv) % -- 3% Visible light Reflectance (Rv) -- 89% -- 83% UV transmission T-UV 0% T-UV 0% Visible light Transmittance (Tv) 5.5% 6% NFP (diffus-diffus) Global thermal conductivity*** Vertical / Horizontal position U= 5.6 / 6.4 W/sqm/ C U= 5.6 / 6.4 W/sqm/ C Acoustic performance Weakening index 16dBA 16dBA ISO LEED Heat island Effect Non roof (up to 2 pts) Solar Reflectance Index >95% Solar Reflectance Index >95% SSc 7.1 Roof (up to 1 pt) Solar Reflectance Index >95% Solar Reflectance Index >95% SSc 7.2/GIB C9 (ND) Environmental Impact: LCA (Life Cycle Assessment) ISO Comparative analysis depending on end-of-life scenarios Texyloop Recycling Incineration Landfill Functional unit = 1 sqm Material only / 1502 S2 values Resources depletion Kilograms eq. Sb Global warming Kilograms eq. CO 2 Energy consumption Megajoul eq. Water consumption Litre Management systems Quality in conformity with ISO 9001 Environmental communication in conformity with ISO Certifications, labels, recycling capacity Précontraint is a Serge Ferrari registered trade mark. ref SEPT 2012/ V1.01 Studio Serge Ferrari GB LCA and LEED reports (S2 and T2) available on request > The values here above are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. * Warranty: Please refer to the text of our warranty. The warranty is valid only after confirmation on case-by-case basis of warranty application. The warranty will not apply to mobile structures. ** See long term case studies in tropical climate (Longevity & sustainability brochure). *** Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installation according to the standards, use and customs and safety rules of the countries where they are used. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover photo: Zayed University, Abu Dhabi (UAE) Serge Ferrari Join us facebook.com/sergeferrarigroup

17 MAIN FEATURES Proven Design life 30 years + Comfort optimization : natural light and solar protection Texyloop recycling: production of 2nd generation materials Durability of mechanical and aesthetical performances APPLICATIONS Major construction projects Tensile roofs and structures Large free span and anti clastic shapes Précontraint TX30-II Choose 30 year design life and above The new generation of Précontraint TX30 composite materials has been developed to match the requirements of the most demanding projects. This technology combines: a CROSSLINK PVDF surface treatment highly resistant to photo-oxidation, a 30YEAR PVC coating formula engineered to resist erosion for more than 30 years, an outstanding dimensional stability thanks to the Précontraint technology. Optimize natural light input and solar protection Précontraint TX30 is engineered to optimize the comfort of the building users: brings in more natural light than the standard PVC composites (Tv 5%), protects better against solar heat than the PTFE composites (G = 20%). Précontraint Précontraint Précontraint Précontraint TX30 - II TX30 - III TX30 - IV TX30 - V Standards Application Static and permanent structures - Tropical climates Surface coating CROSSLINK PVDF Life expectancy > 30 years Technical properties HT polyester cables 1100 Dtex 1100/1670 Dtex 1100/2200 Dtex 1670/2200 Dtex Weight 1050 g/sqm 1050 g/sqm 1350 g/sqm 1500 g/sqm EN ISO Width 178 cm 178 cm 178 cm 178 cm (+1mm /-1mm) Tensile strength (warp/weft) 430/430 dan/5cm 560/560 dan/5cm 800/700 dan/5cm 1000/800 dan/5cm EN ISO 1421 Tear strength (warp/weft) 55/50 dan 80/65 dan 120/110 dan 160/140 dan DIN Adhesion 12 dan/5cm 12 dan/5cm 13 dan/5cm 15 dan/5cm EN ISO 2411 Flame retardancy Euroclass B-s2,d0 B-s2,d0 C-s2,d0 C-s2,d0 EN Rating Depending on the type, other fire certificate/country on demand M2/NFP 92503, B1/DIN4102-1, NFPA 701, CSFM T19,... > The technical data here above are average values with a +/-5% tolerance ADDITIONAL INFORMATION Assembly Weldable after abrasion Total thickness 0.78 mm 0.78 mm 1.02 mm 1.14 mm Micro organism resistance Degree 0, excellent Degree 0, excellent Degree 0, excellent Degree 0, excellent EN ISO 846 Method A Dimensional stability Elongation 24h - 10 dan/5 cm (warp/weft) <1%/<1% <1%/<1% <1%/<1% <1%/<1% EN15977 Residual elongation <0.4%/<0.4% <0.4%/<0.4% <0.4%/<0.4% <0.4%/<0.4% EN15977 Solar optical values Solar Transmittance (Ts) 10 % 9 % 7 % 6 % Solar reflectance (Rs) 75 % 75 % 76 % 76 % Solar Factor (g) 14 % 13 % 11.5 % 10.5 % EN 410 Visible light Transmittance (Tv) 8 % 7.5 % 5.5 % 5 % Visible light Reflectance (Rv) 84 % 84 % 85 % 85 % UV transmission 0% 0% 0% 0% Thermal and Acoustic performances Thermal conductivity (vertical/ horizontal) ca. U=5.6 / 6.4 W/sqm/ C Calculated Acoustic weakening index ca. 14dBA ca. 14dBA ca. 15dBA ca. 16dBA ISO & ISO LEED Heat island Effect Solar reflectance index SRI > 90% SRI > 90% SRI > 90% SRI > 90% SSc 7.2/7.1 (Roof/Non Roof) Management systems Quality in conformity with ISO 9001 Certifications, labels, recycling capacity Environmental impacts: LCA and LEED reports available on request Profil See the brochure Précontraint TX30 is a Serge Ferrari sas registered trademark. Ref Mai 2014/V1.01 Jean Vasseur Communication GB Visible light transmission > TV = 8% Transmission of solar energy > G = 12% Optimum operating and energy cost Dismantling before recycling via Texyloop : 50% environmental impact reduction Select an eco-responsible material Précontraint TX30 is part of the Serge Ferrari eco-design policy including end of life management: Texyloop unique and operational recycling solution, Life Cycle Assessment, Health and Environmental performance: Eco IDentity. > The values here above are given as an indication. Our products are subject to changes prompted by technological developments. We reserve the right to modify their characteristics at any time. The buyer of our products is responsible for checking the validity of the above data. Contact Headquarters: + 33 (0) Your local representative: The Serge Ferrari operational recycling chain Secondary raw materials of high intrinsic value compatible with multiple processes A quantified response to combat depletion of natural resources Cover picture: OL Stadium - Lyon - France Populous Intens-Cité

18 The new generation of composite material Précontraint TX30 has been developed to meet the mechanical and aesthetical longevity requirements of the most demanding projects. In addition to the proprietary Précontraint technology benefits, the Précontraint TX 30 material combines an ultra resistant 30YEAR PVC coating formula and a CROSSLINK PVDF top coat. Exclusive Précontraint Serge Ferrari technology The Serge Ferrari exclusive technology, patented worldwide, provides unique properties to the Précontraint composite membrane compared to conventionally coated materials. The polyester micro-cables are tensionned in both directions during the coating process for greater dimensional stability and consistency. The Précontraint base cloth is therefore more flat and better protected by a high thickness coating at the top of the polyester micro-cables. Natural light for architecture The 30YEAR PVC coating formula provides and outstanding mechanical longevity The mechanical longevity is directly linked to the quality of the coating which protects the yarns. The Précontraint TX30 longevity is served by: A 30YEAR PVC coating formula resistant to the erosion generated by weather agressions ( UV, rain ), A thicker coating at the top of micro-cables thanks to the Serge Ferrari Précontraint technology. 30YEAR PVC A coating formula to stand the test of time Product reference Standard PVC Précontraint TX30 Top coat treatment Standard PVC Formula 30YEAR PVC Formula Cross section after accelerated Weathering test 7500 H - 30 Year Florida Eq 1mm CROSSLINK TOP COAT for durable aesthetics The CROSSLINK top coat formula generates irreversible links between molecular chains. This tridimensionnal network provides long term benefits: higher resistance to photo oxidation and micro-cracks, stable and smoother surface to prevent dirt in-grain, easier and more efficient cleaning of the even surface. CROSSLINK Top coat formula PVDF top coat CROSSLINK PVDF top coat To observe the Précontraint TX 30-II translucency here under, hold this page up against a light source. Coating thickness at the top of the yarns 7500 H - 30 Year Florida Eq Exposed yarns, not protected High erosion Highly protected yarns Very limited erosion PVDF Top coat CROSSLINK PVDF Top coat Polyester micro-cables Polyester micro-cables Coating Coating Mechanical strength evolution The mechanical strength has been measured at different intervals during the accelerated weathering. Précontraint TX30 Standard PVC/PVDF 230 micron protection > Better protection of the base cloth against UV and erosion. Mechanical resistance stability (Similar for Précontraint S2 and T2) 130 micron protection > Less protection of the base cloth against wear and erosion. Loss of mechanical properties Tensile strength evolution (%) Précontraint TX30-II Standard PVC/PVDF h - 14 years eq h - 30 years eq. Exposure time (hours) Surface evolution: Microscopic observation Product reference Standard PVC Précontraint S2 Précontraint T2 Précontraint TX30 Top coat Accelerated weathering H - 10 year Florida Eq Accelerated weathering H - 30 year Florida Eq LARGE SHOT Yarns protection H 30 year Florida Eq PVDF weldable without abrasion PVDF weldable without abrasion Calibrated PVDF weldable after abrasion CROSSLINK PVDF weldable after abrasion 1mm 1mm TX30-II 3000 Précontraint TX30 maintains a better mechanical resistance after 30 years thanks to a better protection of the polyester micro-cables. Lots of micro cracks and exposed yarns Irreversible degradation Lots of micro cracks and dirt build up Limited micro cracks and dirt build up No micro cracks, aesthetics is preserved, easy cleaning TX 30 I - II III IV and V samples are available on demand. The here above data are extracts from a long term accelerated weathering test based on ISO The weathering protocol was validated by comparing outdoor exposed and artificially weathered materials. Study available on demand.

19 Textile Architecture S

20 Technical properties Précontraint 392S Standards Yarn 1100 dtex PES HT Weight 820 g/sqm EN ISO Width 180 cm (-1/+1 mm) Tensile strength (warp/weft) 300/300 dan/5 cm EN ISO 1421 Tear strength (warp/weft) 60/60 dan DIN Adhesion 8 dan/5 cm EN ISO 2411 Porosity +/- 27% Flame retardancy M2/NFP B1/DIN M2/UNE CSFM T19 VKF5.3/SN TEST2/NFPA 701 Surface treatment Formula S / Weldable calibrated PVDF alloy Product application Textile structures The technical data here above are average values with a +/- 5% tolerance. Additional information Coating thickness at the top of the yarns 215 µ (warp) / 300 µ (weft) Total thickness 1.35 mm Efficiency in wind 81% XPG Measurements carried out at the CMEFE in Geneva, sample 25x35 cm Solar and light properties EN ISO 410 Solar Transmission TS 34% Solar Reflexion RS 57% Solar Absorption AS 9% Solar Factor FS(g) 37% Visible light Transmission TV 34% Visible light Reflexion RV 60% Extreme working temperatures -30 C / +70 C in static position Quality management system ISO 9001 * Those data are obtained by calculation through simulations of the average conditions of use, those values must be considered as approximation. The buyer of our products is fully responsible for their application or their transformation concerning any possible third party. The buyer of our products is responsible for their implementation and installationaccording to the standards, use and customs and safety rules of the countries where they are used. Concerning the contractual warranty, please refer to the text of our warranty. The values here above mentionned are the results of tests performed in conformity with the use and customs in terms of studies, they are given as an indication in order to allow our customers to make the best use of our products. Our products are subjects to evolutions due to technical progress, we remain entitled to modify the characteristics of our products at any time. The buyer of our products is responsible to check that the here above data are still valid. is a Ferrari registered trademark. Studio Ferrari - GB July 09/V Précontraint Ferrari U.V. resistant Long life Custom graphics 10 year warranty fixed structures only (upon request) 100% recyclable textile 100% recyclable Ferrari developed the Texyloop technology specifically for the recycling of composite PVC membranes and textiles. Through the management of its end-of-life products Ferrari is committed to sustainable development. Sustainable development Ferrari development is based on strict adherance to good safety and environmental practices. This includes an understanding of Life Cycle Analysis (LCA), selection of the best materials, and eco-design. The Company obtained its first ISO certification in Specification Service The Ferrari specification service is available to inform you, advise you and suggest innovative solutions for your specific requirements. To detail your project, fill in a form under: Cover photo: Bookstore - Arizona State University - USA Photo: Ferrari SA EUROPE FERRARI SA La Tour du Pin - FRANCE Tel: +33 (0) Fax: +33 (0) STAMOID AG Eglisau - SWITZERLAND Tel: +41 (0) Fax: +41 (0) NORTH AMERICA FERRARI TEXTILES CORP. Florida - USA Tel: Fax: LATIN AMERICA FERRARI LATINOAMERICA S.A. Santiago - CHILE Tel: Tel: São Paulo - BRAZIL Tel: Mexico - MEXICO Tel: MIDDLE EAST FERRARI DUBAI Dubai - U.A.E Tel: Fax: ASIA - PACIFIC FERRARI HONG-KONG LTD HONG-KONG Tel: Fax: CHINA FERRARI CHINA Shanghai Tel: Fax: