Pedestal Style Poke-Thru Devices from Wiremold/ Legrand

Transcription

1 Pedestal Style Poke-Thru Devices IT, RC91GHBTC, RC92GHBTC Series High Capacity MultiService Power & Communication Poke-Thru Series Protection from water, dirt, and debris. Pedestal Style Poke-Thru Devices from Wiremold/ Legrand are an ideal solution for bringing large capacity power and communication services to workstations in an open space, above-grade floor environment. Every Pedestal Poke-Thru Device from Wiremold/ Legrand comes with built-in TopGuard protection, an industry-leading design that meets and exceeds UL scrub water exclusion requirements for tile and carpet floors. Topguard protection prevents water, dirt, or debris from entering the power and communication compartments located below the floor, through the service head or floor fittings. All Pedestal Poke-Thru Devices from Wiremold/Legrand can be installed on tile, carpet, or wood floors. Each of these devices provides an excellent solution for both new or retrofit construction, with typical applications that include commercial office buildings, financial institutions, and government facilities. IT with 241 Series Service Head on carpet floor. RC9GHBTC Pedestal Poke-Thru Device on tile floor. eatures & Benefits TopGuard Protection. Integral design component that prevents water, dirt and debris from entering power and communication compartments. Whenever you see the TopGuard protection icon on any Wiremold product, you ll know it meets and exceeds UL scrub water exclusion requirements for tile and carpet floors. UL Listed and UL ire Classified to U.S. and Canadian safety standards for tile and terrazzo. Includes the new UL requirements under UL514A and UL 514C for the scrub water exclusion test for carpet and wood floors. Available in single- or double-width service heads. Greater flexibility and capacity to meet customer power and communication requirements with lower initial cost. RC91GHBTC/RC92GHBTC Series provides a combination of one 1 1/4" and one 1/2" trade size conduit stem. Allows additional space to accommodate communication cables. IT Series provided with one 1" trade size divided conduit stem. Allows for dual service capability. Step-on-it installation. Quick and easy installation without the need for additional fasteners or a second installer. Variety of faceplate configurations available. lexibility to configure service fittings to meet workstation requirements now and in the future, reducing overall life cycle costs. IT Series is fire-rated for up to 4-hour rated floors. The RC91GHBTC and RC92GHBTC are fire-rated for up to 2-hour fire-rated floors. Maintains the 2- or 4-hour fire rating of the floor. Datacom connectivity options. Accepts industry standard and proprietary devices from a wide range of manufacturers to provide a seamless and aesthetically pleasing interface for voice, data, audio, and video applications at the point-of-use. ED1217R2 Updated May 2005 or latest specs visit

2 IT Series Ordering Information IT 2" [51mm] Poke-Thru Insert With Junction Box Assembly 1" trade size barriered conduit. Also includes BX/MC cable connector. 15 1/2" [394mm] NOTE: Must be activated with 200 Series or 241 Series Service Head and IP or P Series aceplates (sold separately) to maintain UL Listing and/or Classification. IT 200 Series Service Head Components With the IT Series, service heads can also be custom built. Combining a housing and base with individual faceplates allows the flexibility to custom design a service fitting to specific job requirements. One housing and base, as well as two faceplates, must be ordered to make a complete service head. These catalog numbers do not include receptacles. Example: To order a 200 Series Service Head with one blank faceplate and one Decora style opening faceplate, order the following: 1 pc. 200-H/BTC Housing and Base. Barrier included (may not be needed for single service applications). 1 pc. IP-B Single-gang plate - blank. 1 pc. IP-SS Single-gang plate with one Decora opening. 200-H/BTC 200 Series Housing and Base Order Information Housing and Base Single width. or 200 Series Service Head. Barrier included (may not be needed on single service applications). Base has a 3/4" trade size knockout for connection to IT insert. Also includes scrub water gasket. IP /8" [48mm] 4 5/8" [118mm] 200 Series aceplate Order Information aceplate Single-gang with one 1.390" [35.3mm] receptacle opening. IP-SS aceplate Single-gang with one 1.390" [35.3mm] receptacle opening. IP aceplate Single-gang with one 1.562" [39.7mm] receptacle opening. IP-T aceplate Single-gang faceplate with one telephone opening. Communication grommets included. IP-B aceplate Single-gang, blank. IP50 aceplate Single-gang with one 1/2" trade size knockout. IP-R aceplate Single-gang with one duplex receptacle opening. IP75 aceplate Single-gang with one 3/4" trade size knockout. 2

3 IT 241 Series Service Head Components With the IT Series, service heads can also be custom built. Combining a housing and base with individual faceplates allows the flexibility to custom design a service fitting to specific job requirements. One housing and base, as well as two faceplates, must be ordered to make a complete service head. These catalog numbers do not include receptacles. Example: To order a 241 Series Service Head with one blank faceplate and one faceplate with two duplex receptacle openings, order the following: 1 pc. 241H/BTC Housing and Base. Barrier included (may not be needed for single service applications). 1 pc. PB-B Two-gang plate Blank. 1 pc. P2R Two-gang plate with two duplex openings. 241-H/BTC 241 Series Housing and Base Order Information Housing and Base Double width. or 241 Series Service Head. Barrier included (may not be needed on single service applications). Base has opening for connection to IT insert. Also includes scrub water gasket. P /2" [64mm] 9" [229mm] 241 Series aceplate Order Information aceplate Two-gang with two 1.390" [35.3mm] receptacle openings. PB-B PSS-SS aceplate Two-gang, blank. aceplate Two-gang with two surge suppression device openings. P P2R aceplate Two-gang with two 1.562" [39.7mm] receptacle openings. aceplate Two-gang with two duplex receptacle openings. PB-ACT aceplate Two-gang. One Activate bezel included. Wiremold open inserts sold separately. P2T aceplate Two-gang with two telephone openings. Communication grommets included. PB-RT aceplate Two-gang. One Ortronics TracJack bezel included. One Ortronics Series II bezel included. lat connector only. P50-50 P75-50 aceplate Two-gang with two 1/2" trade size knockouts. aceplate Two-gang with one 3/4" and one 1/2" trade size knockout. PACT-ACT aceplate Two-gang. Two Activate bezels included. Wiremold open inserts sold separately. P75-75 aceplate Two-gang with two 3/4" trade size knockouts. PB-2RT aceplate Two-gang. Two Ortronics TracJack bezels included. Two Ortronics Series II bezels included. lat connector only. 3

4 IT Series Poke-Thru Accessories Order Information AP-ITTC Poke-Thru Abandonment Plate 2" [51mm]. NOTE: Stem must remain in cored hole CARPET ire-rated Plug or carpet applications. IT-EXT Assembled Extension 4 5/8 [118mm]. Includes 1" trade size barriered conduit and coupling. or use with slabs greater than 8" [203mm] TILE ire-rated Plug or tile applications. TG-1 Communication Grommets One set of two grommets. IT Poke-Thru Series Order Information or a Single-Width Service Head Application: or a Double-Width Service Head Application: 1. Order the IT Poke-thru itting. 1. Order the IT Poke-thru itting. 2. Order the 200-H/BTC Service Head. 2. Order the 241-H/BTC Service Head. 3. Order two faceplates. 1 7/8" [48mm] IP /8" [118mm] IP-R IP50 3. Order two faceplates. 2 1/2" [64mm] 9" [229mm] PB-B P75-75 PB-ACT IP IP-SS IP75 P2R PSS-SS PB-RT IP-B IP-T P2T PACT-ACT PB-2RT 4. Completed Assembly. P Completed Assembly. IMP ANT! All faceplate openings must be closed off if not used, to maintain the fire rating of the device. 4

5 Copper Cross Section: The copper cross-sectional area determines the amount of wire fill capacity in a poke-thru device. Unlike other wire and cable management systems that utilize wire fill capacity, a poke-thru device is UL tested under fire conditions to determine the maximum amount of copper conductors that will pass through a poke-thru device, while maintaining the fire-rating of the concrete slab. The IT with 200 or with 241 Series Service Heads are UL Classified to U.S. and Canadian safety standards (see complete marking on product) to accommodate the following: Maximum Allowable Copper Cross Sectional Area: 200 Series Service Head (Power/Communication Combined). Power compartment = sq. in. [9.91mm 2 ]. Communication compartment = sq. in. [32.39mm 2 ]. IT Series Poke-Thru Specifications 200 Series Service Head (Power only) = sq. in. [42.94mm 2 ]. 200 Series Service Head (Communication only) = sq. in. [42.10mm 2 ]. 200 H/BTC 241 Series Service Head (Power/Communication Combined). Power compartment = sq. in. [23.12mm 2 ]. Communication compartment = sq. in. [32.39mm 2 ]. 241-H/BTC 241 Series Service Head (Power only) = sq. in. [52.85mm 2 ]. 241 Series Service Head (Communication only) = sq. in. [55.06mm 2 ]. Junction Box: Supplied with every insert. 16-gauge C.R.S. galvanized box having the following cubic content, complete with 1/2" and 3/4" trade size knockouts. (Power only...30 cu. in. [492cu cm]. Combination...25 cu. in. [410cu cm]). NOTE: The IT Series Poke-Thru requires a 2" [51mm] cored hole. Copper Cross Sectional Area of Commonly Used Conductors Size Solid # sq. in. [.20645mm 2 ] # sq. in. [.32258mm 2 ] # sq. in. [ mm 2 ] # sq. in. [ mm 2 ] # sq. in. [ mm 2 ] NOTE: Use above values for solid or stranded conductors. loor Coverings: The poke-thru device is fire rated for carpet covered floors, tile floor coverings up to 3/4" [19.1mm] maximum thickness, and linoleum floor coverings up to a maximum of 1/8" [3.2mm] thickness. or other floor coverings not listed above, consult factory. CAUTION: Core bits vary in size from manufacturer to manufacturer. Use a 2" [51mm] American made core bit having an outside diameter of 2 1/16" [53mm]. Minimum hole diameter: 2 1/32" [52mm]. Maximum hole diameter: 2 1/8" [54mm]. CAUTION: These devices meet all UL scrub water requirements, but are not suitable for wet or damp locations, or other areas subject to saturation with water or other liquids such as commercial kitchens. IMP ANT! The above maximum copper cross sectional area values are for each individual power and communication compartment. DO NOT add values together for any one compartment. 5

6 RC91GHBTC RC91GHBTC Poke-Thru Series Ordering Information Poke-Thru Insert and Single Width Service Head Includes insert stem with disposable plate and service head with housing, base, scrub water gasket, and barrier. Service head and insert install together to make a poke-thru assembly. Combine with faceplates (sold separately) to complete service head assembly. NOTE: Part shown assembled. Service head is shipped unassembled with the insert stem. 291-H/BTC RC9S Single Width Service Head Only Includes housing, base, scrub water gasket, and barrier. Use with insert assembly RC9S. Insert Stem with Disposable Plate urniture feed insert with one 1 1/4" and one 1/2" trade size conduit to feed power and communication services. Use with either 291-H/BTC or 292-H/BTC Service Head to form complete unit. RC91GHBTC Series aceplate Ordering Information IP Single-Gang aceplate With one 1.390" [35mm] receptacle opening. 4 5/8" [118mm] IP-SS Single-Gang aceplate With one surge suppression device opening. 1 7/8" [48mm] IP Single-Gang aceplate With one 1.562" [40mm] receptacle opening. IP-T Single-Gang aceplate With one communication opening. Two communication grommets included. IP-B Single-Gang aceplate Blank. IP50 Single-Gang aceplate With one 1/2" trade size opening. IP-R Single-Gang aceplate With one duplex receptacle opening. IP75 Single-Gang aceplate With one 3/4" trade size opening. 6

7 RC92GHBTC RC92GHBTC Poke-Thru Series Ordering Information Poke-Thru Insert and Double Width Service Head Includes insert stem with disposable plate and service head with housing, base, scrub water gasket, and barrier. Service head and insert install together to make a pokethru assembly. Combine with faceplates (sold separately) to complete service head assembly. 292-H/BTC Double Width Service Head Only Includes housing, base, scrub water gasket, and barrier. Use with insert assembly RC9S. NOTE: Part shown assembled. Service head is shipped unassembled with the insert stem. RC9S Insert Stem with Disposable Plate urniture feed insert with one 1 1/4" and one 1/2" trade size conduit to feed power and communication services. Use with either 291-H/BTC or 292-H/BTC Service Head to form complete unit. RC92GHBTC Series aceplate Ordering Information PB-B Two-Gang aceplate Blank. 9" [229mm] P50-50 Two-Gang aceplate With two 1/2" trade size openings. 2 1/2" [64mm] P2R Two-Gang aceplate With two duplex receptacle openings. P75-75 Two-Gang aceplate With two 3/4" trade size openings. P2T Two-Gang aceplate With two communication openings. our communication grommets included. PSS-SS Two-Gang aceplate With two surge suppression device openings. 7

8 RC92GHBTC Series aceplate Ordering Information (Continued) PACT-ACT Two-Gang aceplate Two Activate bezels included. Wiremold open inserts sold separately. PB-ACT Two-Gang aceplate One Activate bezel included. Wiremold open inserts sold separately. PB-2RT Two-Gang aceplate Two Ortronics TracJack bezels included. Two Ortronics Series II bezels included. lat connectors only. PB-RT Two-Gang aceplate One Ortronics TracJack bezel included. One Ortronics Series II bezel included. lat connectors only. IMP ANT! All faceplate openings must be closed off if not used, to maintain the fire rating of the device. Multiservice Poke-Thru Series Accessories Ordering Information ABPLUG3 Abandonment Plug Assembly Complete plug assembly for 3 3/16" [97mm] 7" [178mm] abandoning an open 3" [76mm] cored-hole. Assembly includes intumescent fire-stop material to maintain the fire-classification of the floor, integral retainer ring to prevent the unit from pulling up through the floor, and a black die-cast aluminum cover. TG-1 Communication Grommets One set of two grommets (one grommet shown). RCAPTCBK Abandonment Plate Black. 8

9 Multiservice Poke-Thru Series Ordering Information or a Single Width Service Head Application: or a Double Width Service Head Application: 1. Order the RC91GHBTC Poke-Thru itting and Service Head: 1. Order the RC92GHBTC Poke-Thru itting and Service Head: NOTE: Service head is shipped unassembled. 2. Order two faceplates: NOTE: Service head is shipped unassembled. 2. Order two faceplates: 1 7/8" [48mm] 4 5/8" [118mm] 2 1/2" [64mm] 9" [229mm] PB-B IP IP-SS P75-75 IP IP-T P2R PSS-SS IP-B IP50 P2T PACT-ACT P50-50 PB-ACT IP-R IP75 PB-RT PB-2RT 3. Completed Assembly: 3. Completed Assembly: 9

10 Multiservice Series Specifications Copper Cross Section: The copper cross-sectional area determines the amount of wire fill capacity in a poke-thru device. Unlike other wire and cable management systems that utilize wire fill capacity, a poke-thru device is UL tested under fire conditions to determine the maximum amount of copper conductors that will pass through a poke-thru device, while maintaining the fire-rating of the concrete slab. The Multiservice Series is UL Classified to U.S. and Canadian safety standards (see complete marking on product) to accommodate at a maximum the following: Maximum Allowable Copper Cross Sectional Area: 291 Series Service Head (Power/Communication Combined). Power compartment = sq. in. [9.91mm 2 ]. Communication compartment = sq. in. [32.39mm 2 ]. 291 Series Service Head (Power only) = sq. in. [42.94mm 2 ]. 291 Series Service Head (Communication only) = sq. in. [42.10mm 2 ]. 292 Series Service Head (Power/Communication Combined). Power compartment = sq. in. [33.03mm 2 ]. Communication compartment = sq. in. [32.39mm 2 ]. When using flexible metallic conduit the communication compartment can be increased to sq. in. [64.77mm 2 ]. Copper Cross Sectional Area of Commonly Used Conductors Size Solid # sq. in. [.20645mm 2 ] # sq. in. [.32258mm 2 ] # sq. in. [ mm 2 ] # sq. in. [ mm 2 ] # sq. in. [ mm 2 ] NOTE: Use above values for solid or stranded conductors. IMPANT! The above maximum copper cross sectional area values are for each individual power and communication compartment. DO NOT add values together for any one compartment. Tile, Terrazzo, Linoleum, or Carpet 292 Series Service Head (Power only) = sq. in. [42.94mm 2 ]. 292 Series Service Head (Communication only) = sq. in. [42.10mm 2 ]. When using flexible metal conduit the communication compartment can be increased to sq. in. [64.77mm 2 ]. loor Coverings: The poke-thru device is fire rated for carpet covered floors, tile floor coverings up to 3/4" [19.1mm] maximum thickness, and linoleum floor coverings up to a maximum of 1/8" [3.2mm] thickness. or other floor coverings not listed above, consult factory. Scrub Water Gasket 1/2" Trade Size EMT Conduit 8 3/4" [222mm] Long Side View of Service Head Concrete Slab 1 1/4" Trade Size EMT Conduit 5 3/4" [146mm] Long Communication Cables Concrete Thickness Min/Max: 1-HOUR RATED LOOR 2 1/4" [57mm] min over top of deck (or 3" [76mm] thick reinforced concrete slab) to a maximum of 7 1/2" [191mm]. 2-HOUR RATED LOOR 3 1/4" [83mm] min over top of deck (or 4" [102mm] thick reinforced concrete slab) to a maximum of 7 1/2" [191mm]. Junction Box (Not Supplied) Can Be Used to Make Power Connections NOTE: The Multiservice Poke-Thru Series requires a 3" [76mm] cored hole. CAUTION: Core bits vary in size from manufacturer to manufacturer. Use a 3" [76mm] American made core bit having an outside diameter of 3 1/16" [78mm]. Minimum hole diameter: 3 1/16" [78mm]. Maximum hole diameter: 3 1/8" [79mm]. CAUTION: These devices meet all UL scrub water requirements, but are not suitable for wet or damp locations, or other areas subject to saturation with water or other liquids such as commercial kitchens. 10

11 Notes Guide orm Specs CAD Drawings Available 11

12 Datacom Connectivity Options Now you have a wide range of options for providing datacom connectivity into Wiremold Cable Management Systems. They are: Ortronics TracJack and Series II Modular Connectivity Solutions Pass & Seymour Activate Modular Inserts Open System Communication Modules Use these icons to determine connectivity options for each Wiremold System component: Ortronics Connectivity TracJack Individual Jack System ront-loading, snap-in design supports future moves adds and changes Inserts for voice, data, audio, and video Available Category 3, 5e, 6, USOC 6-position, and other media Choice of 13 colors and color matched to Wiremold Systems Universal T568A/B wiring format Series II ront-loading, Module System Module design features easy snap-in front-loading design Linear 110 punch down format for easy termination Inserts for voice, data, audio, and video Available Category 3, 5e, 6, USOC 6-position, and other media Color matched to Wiremold Systems or detailed product selection refer to the Ortronics Catalog or visit Pass & Seymour Legrand Network Wiring Activate Series ront-loading Inserts Modular inserts for voice, data, audio and video applications ront-load, snap-in design Color and texture matched to Wiremold Systems Available Category 3, 5e, 6, as well as 6-position USOC Universal T568A/B wiring format or detailed product selection refer to the Pass & Seymour Network Wiring Catalog or visit Open Connectivity Solutions Wiremold Open System Communications Modules Accommodate a wide range of manufacturers communications outlets including keystone jacks, as well as proprietary solutions from Avaya (Lucent) and NORDX Modules insert into a wide range of Wiremold Systems Pre-punched faceplates accept common communication devices NOTE: or more information on integrating connectivity into Wiremold Cable Management Systems contact the Wiremold Applications Engineering Team or your local Wiremold Sales Representative. Wiremold / Legrand U.S. and International: 60 Woodlawn Street West Hartford, CT AX Outside U.S Canada: 570 Applewood Crescent Vaughan, Ontario L4K 4B AX Copyright 2005 The Wiremold Company All Rights Reserved ED1217R2 Updated May 2005 or latest specs visit