Fire Protection Coatings

Transcription

1 Class A+ NO VOC-emissions! Fire Protection Coatings for green building sustainable and environmentally friendly Non-VOC, free from halogens, APEO, borates, fibres and VOC-emission class A+ Member of Deutsche Gesellschaft für Nachhaltiges Bauen e.v. German Sustainable Building Council LEED Building Material for Ecologically Building according to LEED credit c4.2

2 Environmentally Friendly Fire Protection Coatings for Green Building The focus of our work is to develop sustainable and environmentally friendly fire protection coating products for the use in passive fire protection. Hensel Green Product Line presents those fire protection products which have qualified for ecological construction due to the low portion of volatile organic compounds (VOC) of less than 0.1 percent below the detection limit. These products therefore meet the requirements under the Principles for the health assessment of construction products used in interiors (DIBt notices 10/2010) in conjunction with the LCI values given by the Committee on the health assessment of construction products (AgBB) and are thus also recommended for use in public buildings, which must meet the criteria of the assessment system, Sustainable Construction for Federal Buildings, set out by the Federal Ministry of Transport, Building and Urban Development.. Green Products meet the requirements of the LEED credit EQ C4.2. LEED stands for Leadership in Energy and Environmental Design. This label was created in 1998 by the U.S. Green Building Council and sets strict standards on the presented construction. The emission certificates of our products according to ISO and the AgBB rating scheme give architects and planners so called credit points for the assessment of the environmental standards of a building according to BREEAM and for the seal of approval awarded by the German Sustainable Building Council (DGNB). Due to the French emission certificates according to DEVL D and DEVL A all of our Green Products are classified in the VOC-emission class A +. made in Germany 60 Years of Knowledge in Developing Fire Protection Coatings Our fire protection coating systems HENSOTHERM and HENSOMASTIK are developed and produced exclusively at our headquarters in Börnsen near Hamburg. The products offer intumescent or ablative acting coatings for the fire protection of steel, wood, concrete, cables, for penetration sealings and for fire protection joints. Hensel fire protection coating systems are approved according to DIN/EN and own further international certificates e.g. BS, VKF, UL, GOST. Made in Germany TÜV NORD CERT standard A75-S018 Certificate Registration No Green Product sustainable and environmentally friendly

3 Fire Protection Coatings for structural steel profiles HENSOTHERM 410 KS / 420 KS intumescent fire protection coating/indoor use approved according to EN eta-no. 11/0481, 12/0050 CE-marking according to 93/68/EWG dgnb Navigator: ZK5AGG / 3E4MHK coating systems HENSOTHERM 410 KS focused mainly on: R 30 R 60 open steel profiles / R 30 up to Hp/A 390m -1 ; R 60 up to Hp/A 350m -1 (T crit. 500 C) HENSOTHERM 420 KS focused mainly on: R 90 R120 open steel profiles / R 30 R 90 closed steel profiles / R 90 for columns/i-/h-sections up to Hp/A 315m -1 ; R 90 for beams/i-/h-sections up to Hp/A 335m -1 (T crit. 500 C) assessed also for use on galvanized profiles; no limitation to the galvanized layer high efficiency due to low material consumption/low coverage rates and fast drying times; maintenance-free HENSOTHERM 460 KS / 470 KS intumescent fire protection coating/indoor use classified according to BS 476 certifire certificate No. CF 701 / CF 812 coating systems HENSOTHERM 460 KS fire resistance rates: R 30 R120 / for open steel profiles R 60 up to Hp/A 330m -1 ; for hollow sections R 60 up to Hp/A 245m -1 HENSOTHERM 470 KS fire resistance rates: R 90 R120 / for open steel profiles R 90 up to Hp/A 330m -1, R120 up to Hp/A 325m -1 ; for hollow sections R 90 up to Hp/A 335m -1, R 120 up to Hp/A 210m -1 assessed also for use on galvanized profiles; no limitation to the galvanized layer high efficiency due to low material consumption/low coverage rates and fast drying times; maintenance-free HENSOTHERM 490 KS intumescent fire protection coating indoor/use classified according to UL 263 ul online certification directory file: BXUV.Y627 + BXUV.Y628 coating system fire resistance rates up to 2 hours according to UL 263 for open steel profiles: 2 hours up to Hp/A: 415m -1 W/D = 0,33; for hollow sections: 2 hours up to Hp/A: 167m -1 A/P = 0,236 suitable also for use on galvanized profiles; no limitation to the galvanized layer high efficiency due to low material consumption/ low coverage rates and fast drying times; maintenance-free smooth surface due to low coating thicknesses topcoat available in RAL/NCS or individual colour shades on request suitable also for shop application for penetration sealings for Mixed Penetration Seal System EI 90 ablative fire protection coating system for bulkheading penetrations of cables and pipes in walls and ceilings classified according to EN EI 90 tested in accordance to ETAG / EN eta-no. 10/0214 CE-marking according to 93/68/EWG area of application: penetration seals in brick, concrete and porous concrete walls or in lightweight walls, thickness 100mm; penetration seals in concrete or porous concrete ceilings, thickness: 150mm; lines such as electrical, telecommunication and data cables, refrigerating lines and/or pipes (combustible/non-combustible); penetration seals in reserve and additional services are approved for indoor and outdoor use, durability class X according to ETAG packaging: 12,5 kg plastic pails for Mixed Penetration Seal System EI 60 ablative fire protection coating system for bulkheading penetrations of cables and pipes in walls and ceilings classified according to EN EI 60 tested in accordance to ETAG / EN eta-no. 11/0209 CE-marking according to 93/68/EWG area of application: penetration seals in brick, concrete and porous concrete walls, thickness 100mm; in light-weight walls, Thickness 94mm; penetration seals in concrete or porous concrete ceilings, thickness: 150mm; lines such as electrical, telecommunication and data cables, refrigerating lines and/or pipes (combustible/non-combustible); penetration seals in reserve and additional services are approved for indoor and outdoor use, durability class X according to ETAG packaging: 12,5 kg plastic pails Fire Protection Coatings Rudolf Hensel GmbH 06/14

4 for wooden building materials HENSOTHERM 1 KS INNEN intumescent fire protection coating classifies solid wood and wooden materials as hardly combustible B1 classified according to EN B-s1, d0 P-BRA , FIRE LABS BRA09, Berlin Giscode: M-KH01 synthetic resin, transparent free from halogens, APEO, borates, fibres and free from formaldehyde non-voc according to ISO , LEED A+ this and of April 19, 2011 (arrête area of application: solid wood, thickness 12 mm / particle boards, thickness 12 mm / plywood for construction, thickness 12 mm for interior use only protect against mechanical stress aromatics-free top coat, matt/silk-matt packaging: 6 kg, 12,5 kg, 25 kg plastic pails HENSOTHERM 2 KS INNEN weiss intumescent fire protection coating classifies solid wood and wooden materials as hardly combustible B1 classified according to EN (SBI-test) P-BRA , FIRE LABS BRA09, Berlin dispersion free from halogens, APEO, borates, fibres and free from formaldehyde non-voc according to ISO , LEED A+ this and of April 19, 2011 (arrête area of application: solid wood, thickness 12 mm / particle boards, thickness 12 mm / plywood for construction, thickness 12 mm for interior use only protect against mechanical stress top coat, silk-matt; available in RAL or NCS colour shades and on request in individual colour shades packaging: 6 kg, 12,5 kg, 25 kg plastic pails for electrical cables ablative fire protection coating system for use on horizontal and vertical oriented electrical cables authorization/certification: Z German Institute of Structural Engineering, Berlin/ HH Germanischer Lloyd, IEC cat. A/U MPA Brunswick/ HH Germanischer Lloyd, IEC /Test Report nkt cables, , 90 min., MPRXCX > 3 x 4 mm2/03-hg PDA American Bureau of Shipping, IEC 60332/E DET NORSKE VERITAS, IEC cat. A impermeable to water according to DIN 1048 Non-VOC according to ISO , LEED A+ this and of April 19, 2011 (arrête area of application: for horizontal or vertical oriented cables, in- and outdoor application supporting structures resistant to mechanical stress, oil and petrol spills, ageing and after through drying temperature down to -40 C also flexible in higher dry film thicknesses for application on insulating material and gypsum boards, please contact our Technical Support for detailed instructions packaging: 12,5 kg and 25 kg plastic pails HENSOTHERM 7 KS fabric intumescent fire retardant fabric coated with HENSOTHERM 7 KS for covering of horizontal oriented electrical cables, trays and holders eta 13/0092 (October 2010) and AgBB (June 2012 area of application: covering horizontal oriented electrical cables, trays and holders carrier material: glass filament fabric, noninflammable A2 flexible for use in tightest windings durability classes: Y2/Z1/Z2 fire resistance rate: up to 90 minutes packaging: rolls, 1,20m width x 10m length No VOC-emissions Minimal VOC-emissions

5 for structural elements of concrete HENSOMASTIK B 3000 ablative fire protection coating classified according to EN an expertise can be issued depending on the sort of concrete elements used in a building (October 2010) and AgBB (June 2012 interior and exterior use application areas: for concrete and reinforced concrete components especially for restoration of ceiling or ribbed slabs also in areas exposed to high emissions (e.g. underground car parks) fire retardant class of concrete can be improved up to 90 minutes (R 90), depending on the thickness of concrete by application impermeable according to DIN 1048 resistant to oil and petrol spills weatherproof/uv resistant according to DIN in combination with BETON-CARBONSPERRE protection against penetration of harmful substances HENSOTHERM 820 KS intumescent fire protection coating approved according to EN ; Efectis Nederland B.V. Report: 2012-Efectis-R0556 [Rev1]; Exova Warringtonfire WF-Report No.: minimal VOC < 5g/l, LEED interior use application areas: for concrete hollow core slabs, concrete elements and tunnel construction fire resistant rates: R 30 R240 in combination with BETON-CARBONSPERRE protection against penetration of harmful substances smooth surface high efficiency through low material consumption easy to handle, maintenance-free no spalling by subsequently wall breakthroughs or installations for fire protection joints for single pipes/electrical cables Joints ablative fire protection coating tested according to DIN 4102 A+ this and of April 19, 2011 (arrête area of application: Border, wall and ceiling joints up to R 120 can be produced in concrete and aerated concrete from 100 mm width. for indoor and outdoor use weatherproof / UV-resistant impermeable to water resistant to oil and petrol spills and ageing viscoplastic at high layer thickness after drying packaging: 12,5 kg plastic pails HENSOTHERM Spachtel - universal - fire resistant intumescent sealant; foams in case of fire building material class E acc. to DIN EN A+ this and of April 19, 2011 (arrête area of application: seals gaps or openings in solid ceilings, solid walls and lightweight partition walls 80 mm thickness for single conduits. Border, wall and ceiling joints up to R 120 can be produced in aerated concrete, concrete, reinforced concrete, sand-lime bricks and brickwork in accordance with EN on ceilings from 125 mm / walls from 100 mm. for indoor use only easy to handle colour: grey / can be overcoated packaging: 310 ml cartridge For further information please visit our website

6 Fire Protection Our Passion. Rudolf hensel gmbh Lack- und Farbenfabrik Lauenburger Landstraße Börnsen Germany Tel. +49 (0) Fax +49 (0) Technical Support / Sales +49 (0) info@rudolf-hensel.de Internet: Rudolf Hensel GmbH 06/14 Origin of photo material: 1xpert/fotolia