Data Sheet 3631 Englisch
|
|
- Trevor Oswin King
- 6 years ago
- Views:
Transcription
1 Englisch Silicate Render KR Silikat-Putz Mineral decorative render, in scraped render structure, for exterior use Properties Decorative, easy structurable facade render silicate based with organic stabilizers for exterior use. High adhesion due to silification with the surface and permeable. System-tested as a topcoat in the Brillux ETIC system. Silicate Render can, if required, be ordered as Protect Quality with film preservation against algae and fungal attack. Field of application For obtaining a decorative, weather-resistant surface on silicifying, mineral exterior substrates, e.g., flat exterior plaster surfaces (compressive strength category CS II - CS IV, compressive strength >2 N/mm²), and in Brillux ETICS Systems. On surfaces with long exposure to dampness (depending on the location and construction, as well as on ETICS) there is a risk of algae or fungal infestation. For these surfaces we recommend using the Protect Quality of Silicate Render (see further details about this under Note). Material description Standard color: 0095 white Mixable in lighter colors in the Brillux color system (paint mixing equipment). Further colors available on request. Base material: Potassium water glass with organic stabilizers Density: Approx. 1.8 to 2,0 g/cm³ Sorts: see table on page 2 Packaging: 0095 white: 25 kg Color system (paint mixing equipment): 25 kg Use Thinning If necessary, depending on the surface porosity and object location slightly with water. Tinting Do not tint. Compatibility Only mixable with similar materials and those specified in this Data Sheet. Application Stir Silicate Render KR thoroughly before use with a powerful stirring device (at least 900 Watts) and right hand spiral stirring bar (render stirring bar). The product should be applied with a stainless steel trowel or with a suitable worm pump. Smooth down the applied Silicate Render to its grain thickness. Depending on the wished structure rub down with the Synthetic Trowel 3791 or the Polyurethane Trowel To avoid overlapping apply the render wet on wet. For larger areas apply render with more workers. Date: Page 1 of 5
2 Sorts, structure and consumption Type Structure Grain size Consumption 1) Silicate Render KR K scraped render finish K 2 approx. 3,4 kg/m² Silicate Render KR K scraped render finish K 3 approx. 4,0 kg/m² 1) Determine exact consumption by way of a test application on the object. Application temperature Do not apply if the air and object temperature is below +8 C or higher than +30 C. These temperature limits must be complied with even during the curing time. Tool cleaning Clean tools immediately after use with water. Drying (+20 C, 65 % relative humidity) Surface dry after about 24 hours. Dried through after about 5 days. A minimum drying time of at least 12 hours should be kept between the individual coatings (priming, intermediate coating and render coating). Allow longer drying times at a lower temperature and/or higher air humidity. Storage Cool and frost free. Use material within 12 months. Declaration Water pollution classification Class 1, according to VwVwS. Product-Code BSW40. Comply with the specifications in the current Safety Data Sheet. Coating build-up Substrate preparation The substrate must be capable of being silified, solid, dry, clean, load-bearing and free from efflorescence, sinter layers, separating agents, corrosion promoting components or other compounds affecting intermediate layers. A background moisturizing of the render must be excluded e. g. cracks, connections etc. Check existing coatings for their suitability, load-bearing capacity and adhesive properties. Remove defective and unsuitable coatings thoroughly and dispose of them in accordance with the applicable regulations. Lightly sand and clean smooth, compact substrates. Clean areas infested with fungus or algae thoroughly and treat them with Universal Disinfectant 542*. (* Use biocides safely. Always read labels and product information before use.) Treat replastered areas with a fluorine primer. Allow reinforcement plaster to dry for at least 3 days (at +20 C, 65% rel. humidity) before applying Silicate Render. Apply a prime and/or intermediate coat to the substrate as required. Also see VOB Part C, DIN 18363, Section 3. Page 2 of 5
3 Substrate Prime coat Intermediate coat 2) 3) Top coat Reinforcement plaster, e.g. in Brillux ETICS 1) Untreated, normal and slightly porous surfaces exterior e.g. exterior plaster Silicate Brush Filler 3639 Silicate Render KR in the desired grain size 4) Very porous surfaces, e.g. external plaster, intact mineral coatings 2x wet on damp Silicate Primer 1803 ELF, thinned 1:1 with water 1) Do not use Silicate Render KR on ETICS Reinforcement Plaster ZF-Granit 3535 or ZF-R ) Not required with a white top coat Silicate Render KR (scraped render structure) and with reinforcement plaster with ETICS Powder Adhesive ) With colored top coat use Silicate Brush Filler 3639 in conjunction with the tinted render color. 4) When applying an additional colored coat of silicate facade paint, the render coating should already be tinted to a coordinated color shade. Notes Cover surfaces Cover adjacent areas thoroughly, in particular glass, clinker brick and natural stone. Contiguous surfaces On contiguous surfaces only use materials of a production or mix the required amount of materials. New mineral substrates Allow new mineral substrates, particularly plaster surfaces to cure and dry properly (at least 14 days, better 4 weeks) before coating them. Depending on weather conditions and season, the drying process may take even longer. Colored coating ETICS Colored top coats in ETIC systems with a brightness reference value 20 can be realized without any restrictions. If hues with a brightness reference value < 20 are to be used, contact the Brillux consulting service to clarify if the hues are suitable. As "Protect" quality Silicone render comes with preservation and, for this reason, should only be used for exterior applications. The preservatives used and in particular those identified as Protect minimize and delay the risk of algae and fungal attack. If additional preventive protection is required we recommend applying two additional coats using Silicate Finish 1811 as "Protect Quality", for example. Subject to the status of the technology, more durable protection against algae and fungal infestation cannot be guaranteed. Page 3 of 5
4 Surface shading after drying Because of the chemical bonding process it is likely that the color may change due to weathering and surface shading. This is not a technical or functional defect and does not justify a complaint Equalizing coats for colored designs In the case of colored render coats, a equalizing coat using Silicate Finish 1811 should be applied after allowing for a sufficient drying time (approx. 4 to 5 days, depending on weather). Horizontal surfaces Do not use render coats on horizontal surfaces. Projecting components, e.g. window sills, moldings, crests of walls must be covered properly to prevent dirt stains and penetration of moisture. Further information Follow the instructions on the data sheets of the products used. Characteristically structural grains The additives used in the renders are natural products, which, separated according to render coloring, can be discernible as slightly darker or lighter structural grains. This is a typical character and natural feature of render coats. This is no technical or functional defect and must not give rise to any complaints for this reason. Protection of coating During processing, drying and hardening, the surfaces should be protected against sun impact, strong wind and moisture impact, e.g. by covering them with a tarpaulin. Page 4 of 5
5 CE Marking Water vapor permeability Water absorption Adhesive strength Durability 432 Brillux GmbH & Co. KG Weseler Straße 401 D Münster certificate number from MPA NRW EN Exterior render with organic bonding agents V 1 high W 2 medium 0.3 MPa Reaction to fire A2- S 1,d0 Permeability rate according to EN kg/(m² d 0,5 ) Remark This Data Sheet has been prepared taking into account the current applicable German laws, standards, specifications and codes of practice. All details have been translated from the current German version. The contents do not form a legal contract. The user and/or the purchaser is not released from the responsibility of checking that our products are suitable for the proposed use. In addition our Terms of Conditions and Payment apply. When a new version of this Data Sheet appears with updated information the previous version no longer applies. The current version is available on our website. Version I Brillux Weseler Straße Münster GERMANY Phone Fax info@brillux.de Page 5 of 5
Data Sheet 1806 Englisch
Data Sheet 1806 Englisch Silicate Interior Paint ELF 1806 Silikat-Innenfarbe ELF 1806 low emission, solvent and plasticizer free, dull matt, wet abrasion resistance class 3, suitable for allergy sufferers,
More informationData Sheet 3550 Englisch
Data Sheet 3550 Englisch ETICS Powder Adhesive 3550 WDVS Pulverkleber 3550 mineral adhesive and reinforcing plaster for Brillux ETICS Systems I through VI Properties Mineral adhesive and reinforcing powder.
More informationData Sheet 200 Englisch
Data Sheet 200 Englisch Evocryl 200 Evocryl 200 100 % pure acrylate facade paint, water-dilutable, matt, with photocatalytic effect, highly weather-resistant, dirtresistant due to Evoflex technology, for
More informationData Sheet 832 Englisch
Englisch Primer LF 832 Floortec 2K-Epoxi-Grund LF 832 solvent-free, transparent primer resin as primer in Floortec PUR Coating System and under Floortec 2C Epoxy Thick Layer LF 834 Properties Solvent-free,
More informationData Sheet 3115 Englisch
Englisch Floor Leveling Compound 3115 Fußboden-Nivelliermasse 3115 Very low-emission, self-leveling, high-strength, low-tension, for interior use, with Perimeter Insulation Strip SK 3018 Properties High-strength,
More informationData Sheet 84 Englisch
Data Sheet 84 Englisch Creativ Tenero 84 Creativ Tenero 84 velvet-effect filler, water-based, for smooth, satin surfaces with a subtle metallic look, ready-to-use, for interior use Properties Ready-to-use
More informationTechnical Data Sheet StoSuperlit
Organic natural stone plaster Characteristics Properties Appearance Specific characteristic/ Remarks For exterior use On mineral and organic substrates, primarily in plinth areas and passages Not suitable
More informationCreativ 6c02. Date: Mineral wall designs Page 1 of 4
Venezianische Spachteltechnik Rustika with Creativ Algantico 70 for slightly rough, iridescent contiguous surfaces with fine-rustic character The figure shows a variant of the creative technique and should
More informationData Sheet 3611 Englisch
Englisch ETICS Mineral Wool Lamella Insulation Board 3611 WDVS Steinlamellen-Dämmplatte 3611 MW-L 041 WAP, non-combustible, blunt edges, pre-coated on both sides Properties Nichtbrennbar (non-combustible),
More informationCreativ 6c01. Date: Mineral wall designs Page 1 of 4
Venezianische Spachteltechnik Stucco with for smooth, colored iridescent, contiguous surface with fine marble character The figure shows a variant of the creative technique and should convey an impression
More informationReady-to-use structural plaster for interior use
Ready-to-use structural plaster for interior use Very easy to spread Very robust and hard-wearing surface Uniform Fibre-reinforced, low-stress Easy and flexible to handle Environmentally friendly, low-odour
More informationCreativ 7c04 Englisch
Englisch Fine marble plaster technique Marmor-Feinputztechnik Sichtbetonoptik with Creativ Sentimento 78 for individual, accentuated surfaces with an and and lively texture The figure shows a variant of
More informationDiescolith SOL-Silikat
Highly diffusible SOL silicate paint according to DIN 18363 Silica sol silicate base Tribrid formula Variety of applications Highly weather-resistant Highly water-repellent Highly diffusible UV-light-resistant
More informationTechnical Data Sheet Sto-RFP
Organic, cement-free reinforcing compound/base coat, ready-to-use Characteristics Properties Information/notes Exterior and interior On to organic and mineral substrates As a reinforcing compound for StoTherm
More informationTechnical Data Sheet StoLevell Duo plus
Mineral bonding and reinforcing mortar Characteristics Areas of application Properties Exterior and interior For all mineral substrates For bonding insulation boards onto mineral substrates For producing
More informationTechnical Data Sheet StoSilco R
Silicone resin finishing plaster in rilled texture Characteristics Application Properties Appearance Specific characteristic/ Remarks Technical Data For exterior use On mineral and organic substrates Not
More informationUsing of ETIC System II Verarbeitung WDV-System II ETICS hard foam insulation boards with mechanical fixation (rail system)
Using of ETIC System II Verarbeitung WDV-System II ETICS hard foam insulation boards with mechanical fixation (rail system) System properties Certified external thermal insulation composite system with
More informationData Sheet cg23 Englisch
Data Sheet cg23 Englisch CreaGlas Fabric Art Line CreaGlas Gewebe Art-Line CreaGlas Fabric 3457 in graphical and creative fiber textures Properties CreaGlas Fabric with high weight per unit area in modern
More informationTechnical Data Sheet StoMiral FL Vario
Fibre-reinforced lightweight base coat in accordance with EN 998-1 Characteristics Areas of application Properties exterior and interior as a lightweight and low-stress base coat (approx. 10 mm) onto even
More informationTechnical Data Sheet StoSilco QS R
Silicone resin finishing render with wash-off resistant properties with rilled texture Characteristics Application Properties Appearance Information/notes Exterior Onto organic and, to a limited extent,
More informationData sheet Armatop A - new / Page 1. Areas of application Bonding Bonding of mineral wool, polystyrene and cork external wall insulation boards.
Data sheet Armatop A - new / Page 1 Armatop A - new Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of mineral wool, polystyrene and cork external
More informationMARMOCRYL SILICONE Fine
Technical Datasheet Fine Silicone, pasty, ready-to-use render Smooth finish White or colored Water-repellent Description Fine is a ready-touse, pasty, white or colored, silicone acrylic render. It consists
More informationData Sheet 834 Englisch
Englisch Thick Layer LF 834 Floortec 2K-Epoxi-Dickschicht LF 834 solvent-free, resistant, glossy, self-flowing, for interior use, with Floortec Epoxy Hardener 814 Properties Solvent-free, self-flowing,
More informationTechnical Data Sheet StoDecolit K
Physiologically harmless, organic finishing plaster with stippled texture Characteristics Areas of application Properties Appearance Information/notes interior onto mineral and organic substrates onto
More informationTechnical data sheet StoLevell Uni
Mineral bonding and reinforcing mortar/base coat Characteristics Areas of application exterior and interior for all mineral and almost all organic substrates for bonding insulation boards and render carrier
More informationTechnical Data Sheet Sto-Primer
Filled, pigmented, organic undercoat Characteristics Area of application interior & exterior on mineral and organic substrates for organic and silicone resin renders for modified, mineral renders for dispersion
More informationTechnical Data Sheet Sto-Acoustic Spray Plaster
Mineral acoustic spray plaster Characteristics Properties Appearance interior for ceiling and upper wall areas, areas of high humidity suitable for damp rooms to a limited extent only do not use in brine
More informationData sheet Armatop MP / Page 1
Data sheet Armatop MP / Page 1 Armatop MP Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of ecomin-por, mineral wool, polystyrene and cork exterior
More informationTechnical Data Sheet StoColor Metallic
Coating on pure acrylate base with metallic effect Characteristics Application Properties Appearance Information/notes Exterior and interior on EWIS StoTherm Classic und StoTherm Vario with individual
More informationData Sheet 5v01. System properties. Certified thermal insulation compound
Using of ETIC System I Verarbeitung WDV-System I ETICS hard foam insulation boards using the bonding technique or the bonding and anchoring technique System properties Certified thermal insulation compound
More informationTerra Cotta Glaze Repair System
GUIDELINE FOR WRITING SPECIFICATIONS WHEN USING Terra Cotta Glaze Repair System Select Relevant Section Division 09800 or 099723 Paints and Coatings Part 1 GENERAL 1.1 DESCRIPTION Provide labor, materials
More informationKEIM ETICS-Reno. ETICS 1 Systematic Renovation. PREMIUM is our Standard. ETICS = external thermal insulation composite systems
KEIM ETICS-Reno ETICS 1 Systematic Renovation PREMIUM is our Standard. 1 ETICS = external thermal insulation composite systems ETICS Renovation why? The first thermal insulation composite systems were
More informationMapetherm AR1 Light. Lightweight one-component cementitious mortar FOR THERMAL INSULATION WITH SUPERIOR LIGHTNESS AND ASTONISHING PERFORMANCE
Mapetherm AR1 Light Lightweight one-component cementitious mortar FOR THERMAL INSULATION WITH SUPERIOR LIGHTNESS AND ASTONISHING LIGHTWEIGHT Mapetherm AR1 Light One-component, lightweight cementitious
More informationNEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE
NEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE What is negative side waterproofing? A typical case of negative side waterproofing is when water comes through the walls of a basement and the
More informationCaparol System PRO Data sheet
System features Expanded polystyrene insulation Cost effective solution Excellent detailing options Proven technology Wide variety of colours Reliable protection and crack resistance Proven track record
More informationTechnical data sheet. Diesco Silicon plus. Silicon resin façade paint. High-grade, matte silicon resin facade paint with SIO-TEC formula
High-grade, matte silicon resin facade paint with SIO-TEC formula SIO TEC formula: Formation of three-dimensionals silicon oxide meshes for coatings with low soiling tendency and high colour stability.
More informationNEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE
NEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE What is negative side waterproofing? A typical case of negative side waterproofing is when water comes through the walls of a basement and the
More informationOne component mineral based waterproof slurry «Negative waterproofing!» AQUAFIN -1K
One component mineral based waterproof slurry «Negative waterproofing!» AQUAFIN -1K Why AQUAFIN -1K AQUAFIN -1K is a rigid waterproof slurry for the inside and the outside. It resists the sulfate and is
More informationTechnical Data Sheet StoSilent Fine
Organic, sound-permeable acoustic coating Characteristics Application Properties interior onto ceiling and wall surface areas without mechanical stress sprinkled onto ceilings laminated with StoSilent
More informationNEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE
NEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE What is negative side waterproofing? Why use KÖSTER waterproofing systems? A typical case of negative side waterproofing is when water comes
More informationR3 Cementitious Pore Sealer and Levelling Mortar
Product Data Sheet Edition 15 June 2010 Identification no: 02 03 02 05 001 0 000042 (Template for local translation, only for internal use) Sika MonoTop -723 N R3 Cementitious Pore Sealer and Levelling
More informationPERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960
STUC-O-FLEX PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary
More informationTwo-component, highly flexible, cement-based waterproofing slurry
Technical Datasheet AQUAMAT-ELASTIC Two-component, highly flexible, cement-based waterproofing slurry Description AQUAMAT-ELASTIC is a two-component, highly flexible waterproofing slurry consisting of
More informationPolymer bonding aid and mortar additive bonding agent for old and new concrete. Test method Typical result Control. Compressive strength (BS6319,Pt2)
Techno Bond SBR Polymer bonding aid and mortar additive bonding agent for old and new concrete Uses For improving the physical properties of cementations mixes. Typical uses include, but are not limited
More informationTechnical Data Sheet StoCrete RM F
Quick repair mortar for floors, polymer-modified, cementitious, layer thickness 2-40 mm Characteristics Area of application as non-sag repair mortar for reprofiling, touching up, and filling recesses and
More informationMeldorfer Flachverblender ,
Meldorfer Flachverblender 071 079, 085 087 Flat facing bricks as cladding for exterior or interior surfaces to create the appearance of brickwork or natural stone masonry. Suitable for Capatect ETICS Product
More informationTechnical Data Sheet
Permanent coating, which facilitates removal of graffiti. Agent description: KTX 07 is a unique, single component, colorlessly drying agent based on synthetic organosilicon polymers, applicable for surface
More informationcolorstuk 2-12 Ceramic tiles with relief to be covered with grouting material.
Technical Sheet colorstuk 2-12 colorstuk 2-12 is a type CG 2 fine grain grouting material as per EN 13888, for grouting joints from 2 to 12 mm. It is easy to apply, resistant and color stable, and it is
More informationBTM BT2K 600. Areas of Use
BTM BT2K 600 Bitumento BT2K 600 is a solvent-free, two-component, elastic, water-based, fiber reinforced, rubber and cement based bitumen waterproofing material. Areas of Use As water and moisture tight
More informationConforms to the requirements of ETAG Certificate: European Technical Approval No. ETA-05/0265
PRODUCT DATA SHEET UV-resistant, highly elastic polyurethane waterproofing seal coat PRODUCT DESCRIPTION is a one part, solvent containing, highly elastic, moisture curing polyurethane seal coats. USES
More informationYEARS WATER PROOFING AND PERFORMANCE WARRANTY*
502, 5th Floor, Boston House, Suren Road, Behind Cinemax Theatre, Chakala, Andheri (E), Mumbai - 400 093 Office: +91 226787 2100 Fax: +91 22 26848920 www.jotun.in 10 YEARS WATER PROOFING AND PERFORMANCE
More informationSECTION MAINTENANCE OF STONE ASSEMBLIES
SECTION 04 01 40 - MAINTENANCE OF STONE ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY OF WORK A. Submit the following items in time to prevent delay of the work and to allow adequate time for review, do not order
More informationEPS Heat insulating composite system
EPS Heat insulating composite system Economical external wall insulation With façade insulation sheets made of styropor Heat insulation and façade creation Proven and cost-effective No heat bridges Baumit
More informationbt-3000 n Technical Sheet Recommended use Materials Substrates
Technical Sheet bt-3000 n bt-3000 n is a type D2 dispersion adhesive, as per EN 12004, for laying all kinds of ceramic tiles on indoor walls. This adhesive is served ready-to-use and does not need any
More informationOWL FORCE 10 (A+B+C) Epoxy-cement waterproofing (water barrier).
1618320 WATERPROOFING liquid Epoxycement waterproofing (water barrier). Three component epoxy resin to waterproof in negative and positive pressure, to use as osmotic on underground wall, to encapsulate
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More informationPRODUCT DATA SHEET Sika Level-315 F
PRODUCT DATA SHEET CEMENTITIOUS SELF LEVELLING, FAST DRYING, FIBRE REINFORCED UNDERLAYMENT FOR USE 3-15MM THICK ON INTERIOR FLOORS PRODUCT DESCRIPTION Sika Level-315 F is a one part, polymer modified,
More informationMANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION
STUC-O-FLEX - ELASTOMERIC ACRYLIC FINISH APPLICATION TO PORTLAND CEMENT PLASTER / CONCRETE RENDER MANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION 09220-09 24 00 PART 1-GENERAL SCOPE: Manufacturer's
More informationMANUFACTURERS (SHORT FORM) SPECIFICATION / SECTION
STUC-O-FLEX - ELASTOMERIC ACRYLIC FINISH APPLICATION TO PORTLAND CEMENT PLASTER / CONCRETE RENDER MANUFACTURERS (SHORT FORM) SPECIFICATION / SECTION 09220-09 24 00 PART 1-GENERAL SCOPE: Manufacturer's
More informationcolorstuk especial n
Technical Sheet colorstuk especial n colorstuk especial n is a type CG 2, very fine grain grouting material as per EN 13888, for grouting joints up to 4 mm. Its formula includes ultrafine aggregates, which
More informationcolorstuk 0-4 Technical Sheet Recommended use Materials Substrates Characteristics
Technical Sheet colorstuk 0-4 colorstuk 0-4 is a type CG 2 fine grain grouting material as per EN 13888, for grouting joints up to 4 mm. It is easy to apply, resistant and color stable, and it is specially
More informationTechnical data sheet StoSilent Top Finish
Organic, sound-permeable finishing coat for StoSilent acoustic systems Characteristics Areas of application interior as a top coat for StoSilent Top panel systems Properties sound-permeable Appearance
More informationTwo component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4
Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor S is a suitable screed that can be applied on cement-based floors which need high mechanical
More informationTechnical Data Sheet StoColor Rapid Ultramatt
Physiologically harmless, dead-matt interior dispersion paint with excellent hiding power, wet scrub resistance 2 and hiding power 1 in accordance with EN 13300 Characteristics Application Properties interior
More informationWaterproofing and Damp-proofing Cementitious Slurry
Product Data Sheet Edition: 01/10/2012 Identification no. Version no: GCC SikaTop Seal-107 SikaTop Seal-107 Waterproofing and Damp-proofing Cementitious Slurry Product Description Uses SikaTop Seal-107
More informationOMNITEK Deco is suitable for all leveling and thin layer concrete repair applications, such as:
OMNITEK Deco High strength leveling mortar, Class R4 Product Description OMNITEK Deco is a high strength, cement based, volume stable mortar, suitable for leveling and finishing of concrete surfaces in
More informationSelf-leveling epoxy coating
IN COMPLIANCE WITH EUROPEAN STANDARD PRINCIPLES PI-MC-PR-IR SURFACE PROTECTION SYSTEMS FOR CONCRETE Mapefloor SL SR SYNTHETIC RESINS B2,0 AR0.5-IR4-Bfl-s1 Self-leveling epoxy coating IN COMPLIANCE WITH
More informationTHERMAL INSULATION SYSTEM
opuscolo Kibitherm_EN.FH10 27-06-2007 20:14 Pagina 1 Contents KIBITHERM: a certified system...page 5 Why insulate with KIBITHERM...page 6 KIBITHERM performance features...page 7 How to apply KIBITHERM...page
More informationPRODUCT DATA SHEET. Sika Unitherm Steel S exterior. (formerly Sika Unitherm exterior) PRODUCT DESCRIPTION
PRODUCT DATA SHEET (formerly Sika Unitherm 38091 exterior) Solvent based fire protection coating for steel, fast dry, interior/exterior use PRODUCT DESCRIPTION is an ecological thin film fire protection
More informationRENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION
STUC-O-FLEX RENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION 09 97 23 PART 1-GENERAL 1.00 SCOPE: Manufacturer's specifications containing the requirements necessary
More informationTechnical Data Sheet StoColor Climasan
Physiologically harmless, odour-reducing, deadmatt interior dispersion paint, wet scrub resistance 2 and hiding power 1 in accordance with EN 13300 Characteristics Area of application interior for wall
More informationTechnical data sheet Stolit K
Organic finishing plaster to achieve a stippled texture Characteristics Areas of application exterior onto rendered facades that are solid or that have been insulated onto mineral and organic substrates
More information2013 Product Catalogue
2013 Product Catalogue We Change Chemistry Of The Structure. The quality of the materials used in building and construction areas are also increasing and as a result, lifting our standarts of living to
More informationZinc Silicate (Inorganic)
Product code: 477-041: part A 477-042: part B General description: Two-component, zinc-ethyl silicate-. Forms a continuous coat of metallic zinc that provides cathodic protection to metal (as in hot galvanization).
More informationPRODUCT DATA SHEET Sikadur 31 CF Normal (formerly Sikadur 731)
PRODUCT DATA SHEET (formerly Sikadur 731) 2-part Thixotropic Epoxy Adhesive PRODUCT DESCRIPTION Sikadur-31 CF Normal is a solvent-free, moisture tolerant, thixotropic, structural two part adhesive and
More informationYtong Multipor Mineral Insulation Boards Tender Text, Ceiling Insulation
Tender Text, Ceiling Insulation Tender text, Ceiling Insulation 1 Bill of Quantities Sample Specifications Application: DI "Ceiling Insulation" Construction Project: Bidder: 2 General Information & Comments
More informationPlanitop Range. Smooth any surface PRODUCTS FOR BUILDING ADHESIVES SEALANTS CHEMICAL PRODUCTS FOR BUILDING
Planitop Range PRODUCTS FOR BUILDING Smooth any surface ADHESIVES SEALANTS CHEMICAL PRODUCTS FOR BUILDING Planitop Range There is a vast array of substrates employed in the building industry, such as fresh
More informationTechnical Data Sheet StoCrete TG 203
Repair mortar, polymer-modified, cementitious, layer thickness 6-30 mm Characteristics Area of application as concrete repair product for the structural and non-structural repair of concrete structures
More informationR4 Hand Placed / Wet Spray Repair Microconcrete
Product Data Sheet Edition 02/12/2014 Identification no: 01 03 02 04 001 0 000004 Sika MonoTop-612 R4 Hand Placed / Wet Spray Repair Microconcrete Construction Product Description Sika MonoTop-612 is a
More informationTechnical data sheet StoColor Climasan
Physiologically harmless, odour-reducing, deadmatt interior dispersion paint, wet scrub resistance 2 and hiding power 1 in accordance with EN 13300 Characteristics Areas of application Properties interior
More informationARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment
ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099600 - HIGH PERFORMANCE COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationHomogenous cement-based powder, modified with high quality polymers and cellulose additives.
Page: 1 от 5 (winter formula) adhesive mortar solution for bonding thermo insulation EPS/XPS boards on different bases when thermo-insulating buildings, in mild winter conditions (temperatures from 0 C
More informationGood Construction Practices Part II
Good Construction Practices Part II This report is solely for the internal use. No part of it may be circulated, quoted, or reproduced for distribution outside the company organization without prior written
More informationTechnical Data Sheet StoCrete TG 252
Repair mortar, sulphate-resistant, polymermodified, cementitious, layer thickness 6-30 mm Characteristics Area of application as concrete repair product for the repair of concrete structures (concrete
More informationPRODUCT DATA SHEET Sika Unitherm Platinum
PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.
More informationCEMENTITIOUS CRYSTALLIZING WATERPROOFING PART 1 GENERAL
CEMENTITIOUS CRYSTALLIZING WATERPROOFING PART 1 GENERAL 1.1 SECTION INCLUDES A. Cementitious crystallizing waterproofing for interior/exterior walls and floor slabs with nonactive leaks. B. Cementitious
More informationA. Section includes surface preparation and the application of high-performance coating systems on the following substrates:
ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY
More informationTechnical Data Sheet StoCrete TS 100
Mineral dry spray mortar, layer thickness 6 50 mm Characteristics Functionality Properties As a concrete substitute for repairing statically and non-statically relevant concrete loadbearing structures
More informationTECHNICAL DATA SHEET SIKA RAPID REPAIR MORTAR 25KG
TECHNICAL DATA SHEET SIKA RAPID REPAIR MORTAR 25KG Sika Rapid Repair Mortar is a ready to use [just add water], quick setting mortar, based on special cements. It contains selected aggregates and admixtures
More informationTechnical Data Sheet StoColor Opticryl Satinmatt
Physiologically harmless, silk matt interior acrylate paint, wet scrub resistance class 1 and hiding power class 2 in accordance with EN 13300 Characteristics Application Properties interior for texture-retaining
More informationAPPLICATION The Wall areas to be rendered may require a fungicidal wash Ref. ESPS-ALGICID prior to any render applications.
SPS ENVIROWALL LIMITED NBS SPECIFICATION: RENDER ONLY SYSTEM USING RETROBASE BASECOAT WITH REINFORCEMENT MESH USING SILICONE TOPCOAT APPLIED TO EXISTING MASONRY SUBSTRATE M20 EXTERNAL RENDER SYSTEM To
More informationFor purchasing information visit: Osmo UV Protection Oil Extra
The following Product Datasheet is provided by Osmo Wood Finishes Direct cannot be held liable for the information contained within this document. For purchasing information visit: Osmo UV Protection Oil
More informationConstruction. One component cementitious mortar fibre reinforced for flexible waterproofing. Product Description. Product Data. Form.
Product Data Sheet Edition 12/12/2014 Identification no: 02 07 01 01 001 0 000180 Sikalastic -1K Sikalastic -1K One component cementitious mortar fibre reinforced for flexible waterproofing Construction
More informationTechnical Data Sheet StoCrete TG 114
Screed material, polymer-modified, cementitious, layer thickness 10-40 mm Characteristics Area of application as concrete repair product for the structural and non-structural repair of concrete structures
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationEN R4 High Strength High Build Concrete Repair Mortar
Product Data Sheet Edition 28th February 2018 Sika MonoTop-612 N EN 1504-3 R4 High Strength High Build Concrete Repair Mortar Construction Product Description Sika MonoTop-612 N is a cement-based, one
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationAQUAMAT. Cement-based, brushable waterproofing slurry. Technical Datasheet
Technical Datasheet AQUAMAT Cement-based, brushable waterproofing slurry Description AQUAMAT is a cement-based, brushable waterproofing slurry offering: Total waterproofing against positive hydrostatic
More informationApplication Guidelines
Baumit Renders for Porotherm Masonry Application Guidelines Light and easy application Tried and tested EWI system compatible Ideas with a future. Renders for Porotherm Masonry Baumit lightweight render
More information