Boiler and Pressure Equipment Regulations
|
|
- Morgan Summers
- 5 years ago
- Views:
Transcription
1 Boiler and Pressure Equipment Regulations
2 Changes: Additions and Exemptions to scope New Permitting & Licensing system replaces equipment certification Mandatory Quality Control requirements for owners and contractors Owner - User options Welder qualification & testing
3 Additions The scope of regulation now includes: Pressure Vessels for flammable liquids and gases over 300F Low Pressure Boilers... down to 150 KW (507,000 Btu/hr)
4 New Exemptions.. Boiler systems in a residential building that has 12 units or less Small pressure vessels (separators / autoclaves / air tanks / steam kettles / sterilizers) that have a capacity of 1.5 cu. ft. or less
5 Piping Exemptions Steam: < 15 psi welded < 150 psi < 2 threaded (when it meets an acceptable standard) Direct steam tracing
6 Piping Exemptions Water / Similar: < 160 psi < 250 F < 150 psi < 2 threaded (when it meets an acceptable standard)
7 Piping Exemptions Air: < 200 psi Breathing air systems covered under modular construction with Certification marking from a recognized organization
8 Piping Exemptions Misc: Pneumatic or hydraulic tubing for instrumentation Fuel delivery under the Fuel Safety Regulations Fire suppression under the Fire Safety Regulations Medical and inert gas systems
9 Inspection by Steam or Hot Water Boilers Labour & Advanced Education No Difference Labour & Advanced Education and / or Condition Reports from Industry New 15 psi Steam / 30 psi HW > 150 KW (507,104 BTU/hr) > 12 unit residential dwellings
10 Changes: New Permitting & Licensing system replaces equipment certification
11 Contractor Licensing Owners and mechanical contractors are required to be licensed if they work on regulated products A license is issued based on a registered and implemented Quality Control program Permits are required prior to performing work on a regulated product
12 Quality Program Requirements Some main points of a program; Programs elements that are applicable.. ie materials, welding, purchasing, code compliance Owner- User provincial or NB Routine repairs owner / contractor Inspectors role SAY WHAT YOU DO AND DO WHAT YOU SAY!
13 Welding in Nova Scotia
14 The basics New welders after April 1 st must meet the minimum education and experience prior to an initial plate test. Plate tests are required prior to pipe testing* It is now called a license *Previous qualifications are honored
15 Two classes of welders 1. Pressure welder (plate) license initial qualifications for a NSID Previous qualification from a recognized certification organization or authority having jurisdiction OR Holds a journey person status in welding or a red seal OR Has successfully completed a recognized welding diploma program OR Has completed at least 1 year of practical experience in welding
16 Two classes of welders 2. Pressure welder (pipe) license initial qualifications Have successfully completed a preliminary welder proficiency test by a BPE inspector AND Previous qualification from a recognized certification organization or authority having jurisdiction OR Holds a journey person status in welding or a red seal OR Has successfully completed a pressure pipe welding course recognized by a recognized certification organization OR Has completed at least 2 years of practical experience in welding
17 Special Note... REMEMBER THAT AN NSID will be required to permit performance testing of an individual
18 Examples of work / permits
19 Example1: Owner doing Maintenance...wants to do their own routine maintenance on piping / valves / fittings etc QC registered manual detailing scope Welding procedures / tested welders Routine repairs listed and agreed upon in manual Must maintain records and qualifications Will be audited by department (no permit)
20 Example 2: Contractor doing repairs... Pressure part leaks / replacement in-kind QC registered manual detailing scope Welding procedures / tested welders Only routine repairs listed and agreed upon in manual along with reporting notification to inspector...no Permit required Must maintain records and qualifications Will be audited by department
21 Example 3: Contractor upgrades / alterations... New systems / alterations / accidents QC registered manual detailing scope Welding procedures / tested welders Reporting notification and Permit Must maintain records and qualifications Will be inspected by department
22 Example : Owner / User... Maintenance / repairs QC registered manual detailing scope Welding procedures / tested welders Repairs & pressure work listed and agreed upon in manual Owner inspector trained and is responsible Must maintain records and qualifications Will be periodically audited by department (no permit)
23 Permits For work that notification is not exempted through QC system 1. Notify your area inspector as before 2. Visit Service Nova Scotia s website, print off copy of application and fax to Halifax office. 3. Will require notification / permit on site
24 Sch A..Boiler and Pressure Equipment Regulations BPE Contractor License (QC) BPE Permits Technical Safety Act Section 49 Big Picture... Pressure Equipment License BPE Inspection Pressure Welder License Owners Contractors Manufacturers CSA B51 CSA B52 Codes ASME/ Nat.Board Codes
25 Where to Get More Information Contact the inspector for your area Visit our website at Service Nova Scotia Contact our office at (902)
Guide for the preparation of quality programs for licensing of companies performing BPE regulated work.
Labour and Advanced Education Guide for the preparation of quality programs for licensing of companies performing BPE regulated work. Company Name: QC Program issue#: Revision# Overview: 1. This guideline
More informationREGULATION OF THE MINISTER OF COMMUNITY, ABORIGINAL AND WOMEN S SERVICES. Safety Standards Act M 62
PROVINCE OF BRITISH COLUMBIA REGULATION OF THE MINISTER OF COMMUNITY, ABORIGINAL AND WOMEN S SERVICES Safety Standards Act M 62 I, Murray Coell, Minister of Community, Aboriginal and Women s Services,
More informationB Contractor Licensing GUIDE FOR APPLICANTS
B Contractor Licensing GUIDE FOR APPLICANTS BRITISH COLUMBIA SAFETY AUTHORITY Prepared by: Ed Hurd P.Eng. Provincial Safety Manager, Boilers Date: June 26, 2013 MAN-4048-00 Page 1 of 14 Contents Introduction...
More informationQuality Control Manual Submission Information
330 1855 Victoria Avenue Regina, SK S4P 3T2 PH: (306)798-7111 Toll Free: (866)530-8599 FAX: (306)787-9273 Toll Free: (866)760-9255 Website: www.tsask.ca Table of Contents Quality Control Manual Submission
More informationQuality Control Manual Submission Information
Table of Contents Quality Control Manual Submission Information 1.0 Legislative Requirement 1.1 Exemption to Legislative Requirement 2.0 Required content of Quality Control Manual 2.1 Title Page 2.2 Scope/
More informationB Contractor License GUIDE FOR ASSESSMENT TEAMS & APPLICANTS
BRITISH COLUMBIA SAFETY AUTHORITY B Contractor License GUIDE FOR ASSESSMENT TEAMS & APPLICANTS Prepared by: Ed Hurd P.Eng. Provincial Safety Manager, Boilers Date: June 26, 2013 MAN-4049-00 MAN-4049-00
More informationRefrigeration (REF) Contractor License GUIDE FOR ASSESSMENT TEAMS & APPLICANTS
BRITISH COLUMBIA SAFETY AUTHORITY Refrigeration (REF) Contractor License GUIDE FOR ASSESSMENT TEAMS & APPLICANTS Prepared by: Ed Hurd P.Eng. Provincial Safety Manager, Boilers Date: June 26, 2013 MAN-4047-00
More informationJULY 10, 2013 INTRODUCTION
Guidelines to Establish the Chief Engineer s Responsibility N.J.A.C. 12:90 Boiler, Pressure Vessel and Refrigeration Rules Specifically N.J.A.C. 12:90-3.9 (a) NOTE: PROPER USE OF THIS DOCUMENT WILL ASSURE
More informationHOW TO CONSTRUCT ASME BOILER BY THAI ASSOCIATION OF BOILOER AND PRESSURE VESSEL
HOW TO CONSTRUCT ASME BOILER BY THAI ASSOCIATION OF BOILOER AND PRESSURE VESSEL WHAT IS ASME The American Society of Mechanical Engineers set up a committee in 1911 for the purpose of formulating standard
More information2001 NBIC Interpretations
2001 NBIC Interpretations INTERPRETATION 01-41 Subject: Appendix 2 and Appendix 5 with 2003 Addendum Question: In the event of an alteration to a boiler in which the boiler heating surface and steaming
More informationQUALITY ASSURANCE SPECIFICATION WELDING HEAT TREATMENT PAGE 1 OF 6
QUALITY ASSURANCE SPECIFICATION REVISION: 0 DATE: 08/29/14 WELDING HEAT TREATMENT PAGE 1 OF 6 1.0 Purpose The purpose of this specification is to establish the minimum quality assurance requirements for
More informationWelding Performance Qualification Test Administrators GUIDE FOR APPLICANTS
TECHNICAL SAFETY BC Welding Performance Qualification Test Administrators GUIDE FOR APPLICANTS Date: October 12, 2017 Controlled Document: MAN-4018-02 MAN-4018-02 Page 1 of 27 Contents 1.0 Introduction...
More informationWelding Performance Qualification Test Administrators GUIDE FOR APPLICANTS
BRITISH COLUMBIA SAFETY AUTHORITY Welding Performance Qualification Test Administrators GUIDE FOR APPLICANTS Date: April 25, 2017 Controlled Document: MAN-4018-01 MAN-4018-01 Page 1 of 27 Contents Contents...
More informationPressure Equipment Repair and Alteration Requirements
the pressure equipment safety authority Pressure Equipment Repair and Alteration Requirements AB-513 Edition 3, Revision 0 - Issued 2018-01-30 Table of Contents FOREWORD... iii 1.0 INTRODUCTION... 1 2.0
More informationIDENTIFYING FACTORY TESTS AND CERTIFICATIONS FOR ASME TANKS AND VESSELS. Factory Tests and Certifications for ASME Tanks and Vessels
IDENTIFYING FACTORY TESTS AND CERTIFICATIONS FOR ASME TANKS AND VESSELS Discover How Factory Tests are Conducted and the Documentation Required for ASME Compliance Factory Tests and Certifications for
More informationPresented by: Gary Scribner Manager of Technical Services. Shanghai April The National Board of Boiler and Pressure Vessel Inspectors
Presented by: Gary Scribner Manager of Technical Services Shanghai April 2016 1. Provides administrative and technical rules, and guidelines to follow for repairing or altering a pressure retaining item.
More informationPOWER ENGINEERS ACT REGULATIONS
c t POWER ENGINEERS ACT REGULATIONS PLEASE NOTE This document, prepared by the Legislative Counsel Office, is an office consolidation of this regulation, current to December 26, 2015. It is intended for
More informationACCREDITATION OF BOILER AND PRESSURE VESSEL REPAIR OR ALTERATION ORGANIZATIONS
ACCREDITATION OF BOILER AND PRESSURE VESSEL REPAIR OR ALTERATION ORGANIZATIONS TSSA GUIDE FOR SURVEY TEAMS The Technical Standards and Safety Authority Boilers and Pressure Vessels Safety Division 3300
More informationThe Pipelines Regulations, 2000
PIPELINES, 2000 P-12.1 REG 1 1 The Pipelines Regulations, 2000 being Chapter P-12.1 Reg 1 (effective April 1, 2000) as amended by the Statutes of Saskatchewan, 2014, c.21; and by Saskatchewan Regulations
More informationASME B31.3 Process Piping. 19. What s Different in B31.1
ASME B31.3 Process Piping Charles Becht IV, PhD, PE Don Frikken, PE Instructors BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-1 19. What s Different in B31.1 Scope Organization of the Code
More informationMeeting of April 25 th, 2016 Tampa, FL
Date Distributed: April 11th, 2016 NATIONAL BOARD SUBGROUP FRP AGENDA Meeting of April 25 th, 2016 Tampa, FL The National Board of Boiler & Pressure Vessel Inspectors 1055 Crupper Avenue Columbus, Ohio
More informationACCREDITATION OF PRESSURE RELIEF VALVE REPAIR ORGANIZATIONS
ACCREDITATION OF PRESSURE RELIEF VALVE REPAIR ORGANIZATIONS TSSA GUIDE FOR SURVEY TEAMS The Technical Standards and Safety Authority Boilers and Pressure Vessels Safety Division 3300 Bloor Street West
More informationCNC PROFILING PLATE ROLLING SUBMERGED ARC WELDING
CNC PROFILING PLATE ROLLING SUBMERGED ARC WELDING HDS Energy has over thirty years experience in the design, manufacture and installation of bespoke boiler solutions for large energy and power projects
More informationQUALIFICATIONS NEEDED TO DESIGN, CONSTRUCT AND MANUFACTURE NUCLEAR SYSTEMS AND EQUIPMENT. Cosmos M. Voutsinos, P.Eng.
QUALIFICATIONS NEEDED TO DESIGN, CONSTRUCT AND MANUFACTURE NUCLEAR SYSTEMS AND EQUIPMENT Cosmos M. Voutsinos, P.Eng. 1638 Scenic Heights South, Lethbridge, Alberta, Canada 403-331-2212,
More informationPOWER PIPING J\$ME TO ASME B3I.I THE COMPLETE GUIDE. Charles Becht IV PRESS
POWER PIPING THE COMPLETE GUIDE TO ASME B3I.I by Charles Becht IV J\$ME PRESS Contents About the Author List of Figures List of Tables iii ix xi Chapter 1 Background and General Information 1 1.1 History
More informationCNC PROFILING PLATE ROLLING SUBMERGED ARC WELDING
CNC PROFILING PLATE ROLLING SUBMERGED ARC WELDING HDS Energy has over thirty years experience in the design, manufacture and installation of bespoke boiler solutions for large energy and power projects
More informationACCREDITATION OF MANUFACTURERS AND INSTALLERS OF PRESSURE PIPING PARTS AND SYSTEMS
ACCREDITATION OF MANUFACTURERS AND INSTALLERS OF PRESSURE PIPING PARTS AND SYSTEMS TSSA GUIDE FOR SURVEY TEAMS The Technical Standards and Safety Authority Boilers and Pressure Vessels Safety Division
More informationMedina County Building Department
Medina County Building Department Charles E. Huber Building Official chuber@medinaco.org Permit Center 791 W. Smith Rd. Medina, Ohio 44256 Main: (330) 722-9220 Fax: (330) 764-8204 http://building.medinaco.org
More informationConformity Assessment. Dan Cheetham BPV Requirements 4/12/16
Conformity Assessment Dan Cheetham BPV Requirements 4/12/16 BPV Requirements Boiler and Pressure Vessel Requirements (Quality Control Programs, Materials, Examination & Inspection, etc.) Quality Control
More informationREFERENCE SYLLABUS. for WELDING EXAMINER & WELDING EXAMINER IN TRAINING CERTIFICATES OF COMPETENCY EXAMINATIONS
WELDING EXAMINER & CERTIFICATES OF COMPETENCY S AB-94 Edition 2, Revision 0, 2016-05-01 GENERAL INFORMATION INTRODUCTION: This Syllabus is intended to assist candidates in preparing the Welding Examiner
More information1.0 Purpose: To provide a method of assuring that Section XI Repair and Replacement activities. 3.1 ASME B&PV Code, Section XI, Article IWA-4000
Activity: ASME Section XI Repair and Replacement 1.0 Purpose: To provide a method of assuring that Section XI Repair and Replacement activities are in compliance with applicable standards, regulations
More informationNB-435 Rev. 1 Page 2 of 5
The National Board has developed this Body of Knowledge to outline duties and responsibilities for individuals performing inspections during the construction phase of nuclear components, parts, and appurtenances
More informationMunicipality For the purpose of this bulletin, municipality means: a town, village, county, district or a regional municipality.
ELECTRICAL INSPECTION BULLETIN (Effective 2012-10-01) Rule 30-1000 Installation and Inspection Requirements for Street and Roadway Lighting Systems Scope This document covers the installation and inspection
More informationSUPPLIER QUALITY SCOPE AND FACILITY QUESTIONNAIRE. Bantrel Co. Project #:
Bantrel Co. Project #: COMPLETED BY: DATE: SUPPLIER NAME: D & B NUMBER: CONTENTS 1.0 GENERAL INFORMATION 2.0 PERSONNEL 3.0 QUALITY PROGRAM 4.0 SUPPLIER / CONTRACTOR INFORMATION 5.0 SCOPE OF FABRICATION
More informationFORM U-1A MANUFACTURER'S DATA REPORT FOR PRESSURE VESSELS
Job # Description FORM U-1A MANUFACTURER'S DATA REPORT FOR PRESSURE VESSELS 1. Manufactured and certified by Blackeagle Energy Services, 230 Commerce Drive, Berthoud, Colorado, 80513 ( and address of manufacturer)
More informationBoilers and Pressure Vessels Safety Program CODE ADOPTION DOCUMENT AMENDMENT
Boilers and Pressure Vessels Safety Program CODE ADOPTION DOCUMENT AMENDMENT Ref. No.: Rev. No.: BPV-13-01 0 Date: Date: January 21, 2013 January 21, 2013 IN THE MATTER OF: THE TECHNICAL STANDARDS AND
More informationOWNER USER INTEGRITY MANAGEMENT SYSTEM WRITTEN DESCRIPTION CHECKLIST AB-512(b)
Company Name: Written Description of QMS Title and Rev. Status: Person who is responsible for preparing the owner s QMS written description: Name: Title: Telephone No.: ( ) Fax No.: ( ) Cell No.: ( ) E-Mail:
More informationDIRECTIVE Use of ASME Code Case 2596 in Alberta
Information Bulletin No. IB13-008 July 26, 2013 DIRECTIVE Use of ASME Code Case 2596 in Alberta Background ASME Code Case 2596 provides the requirements for design and construction of coldstretching austenitic
More informationSUPERVISING FOOD PRODUCTION EQUIPMENT TECHNICIAN
PERSONNEL COMMISSION Class Code: 0499 Salary Range: 38 (S1) JOB SUMMARY SUPERVISING FOOD PRODUCTION EQUIPMENT TECHNICIAN Under general supervision, to organize, supervise and participate in the highly
More informationA Comparison: ASME B31.1 Power Piping versus ASME B31.3 Process Piping
A Comparison: ASME B31.1 Power Piping versus ASME B31.3 Process Piping Don Frikken, PE BECHT ENGINEERING COMPANY, INC. 1 Topics Discussed B31 History Scopes Organization of the Codes Bases for Allowable
More informationASME CODE CHANGES 2015 EDITION
ASME CODE CHANGES 2015 EDITION SECTION I 2015 Edition published July 1, 2015, mandatory January 1, 2016. No more addenda. Publish every 2 years. Table A-360 : All ASME standards reference current year
More information2004 NBIC Interpretations
2004 NBIC Interpretations INTERPRETATION 04-23 Subject: Part RC 1110, RC-2050(c), RC-3030(c), RC-3031(e) Question 1: Does RC-1110 specifically require acceptance of the jurisdiction for alternative NDE
More informationGuideline for In-Service Assessment of Ammonia Refrigeration Plants
Guideline for In-Service Assessment of Ammonia Refrigeration Plants This communication is intended to be used by plant owners and operators to provide guidance in preparation for an assessment of the plant
More informationList of forms CLAP with correspondence WGP /68/UE
List of forms CLAP with correspondence WGP - 204/68/UE CLAP number CLAP version Adopted by CLAP Subject WGP number Adopted by WGP X00 /03/205 Equipment covered by the regulations on transport of dangerous
More informationApplication for an Ontario Certificate of Authorization For Ontario based businesses CSA N285.0 Nuclear Components
345 Carlingview Drive PRINT Click to clear On completion, send this form to the attention of Boilers and Pressure Vessels Safety at the top left TSSA address. Company: (Legal Company Name and Corporation
More information1 The enacting clause of New Brunswick Regulation under the Boiler and Pressure Vessel Act is repealed and the following is substituted:
1 1 The enacting clause of New Brunswick Regulation 84-177 under the Boiler and Pressure Vessel Act is repealed and the following is substituted: Under section 40 of the Boiler and Pressure Vessel Act,
More informationApplication for an Ontario Certificate of Authorization For businesses based Outside Ontario CSA N285.0 Nuclear Components
345 Carlingview Drive PRINT Click to clear On completion, send this form to the attention of Boilers and Pressure Vessels Safety at the top left TSSA address. Company: (Legal Company Name and Corporation
More informationTurnaround And Major Capital Project Services
Turnaround And Major Capital Project Services ENERGY ENVIRONMENTAL Babcock & Wilcox (B&W) is a leading supplier of turnaround and capital project services for customers in a wide variety of industries,
More informationAssuring Integrity While Bringing Efficiencies to American Industry. What Is Common Arc?
Assuring Integrity While Bringing Efficiencies to American Industry 1 What Is Common Arc? Formed by NACBE January 1988 Not-for-profit corporation formed to: Foster and advance interests of Construction
More informationNAVIGATING ASME SECTION VIII (DIV.1): MANAGING YOUR PRESSURE VESSELS - PART 1 FEATURING:
January/February 2014 Volume 20, Issue 1 Since 1995, Inspectioneering Journal has provided the oil & gas and chemical industries with information to help optimally manage equipment risk and reliability,
More informationOctober 1, 2012 Revisions of TSSA Fuels Safety Code Adoption Documents, Codes and the Environmental Management Protocol
October 1, 2012 Revisions of TSSA Fuels Safety Code Adoption Documents, Codes and the Environmental Management Protocol On October 1, 2012, the Technical Standards and Safety Authority published and revised
More informationTEXAS DEPARTMENT OF LICENSING AND REGULATION
Compliance Division/Boiler Program P. O. Box 12157 Austin, Texas 78711 (512) 539-5716 Fax (512) 539-5687 Email Address: boilers@tdlr.texas.gov Web site: www.tdlr.texas.gov PAPER BOILER INSPECTION REPORTS
More informationList of forms CLAP with correspondence WGP - 97/23/EC
List of forms CLAP with correspondence WGP - 9723EC CLAP number CLAP version Adopted by CLAP Subject WGP number Adopted by WGP 1 9 07092004 ESR on manufacturing - Welded tubes 725 07092004 2 4 26012006
More informationAnchorage Fabrication Facility
Anchorage Fabrication Facility Facility Overview The AES Anchorage Fabrication and Construction group excels at providing all ranges of fabrication and construction services with an emphasis on job safety,
More informationM9C 1A3 VELO (PH) (FX)
PROFESSIONAL DEVELOPMENT COURSES ANRIC Enterprises Inc. 701 Evans Ave, Suite 202 Toronto, ON M9C 1A3 (PH) 416-253-9459 (FX) 416-252-2553 www.anric.com PROFESSIONAL DEVELOPMENT COURSES CONTENTS INTRODUCTORY
More informationDirective 97/23/EC Pressure Equipment
Directive 97/23/EC Pressure Equipment Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
More informationPressure Points. Governing Code Edition Section I Table of Contents
Table of Contents Governing Code Edition... 1 Navigating the use of Small Products NX-2610... 3 Third Party Inspection... 4 ASME Three-Day Seminar... 6 Governing Code Edition Section I - 2017 The governing
More informationCQ ENGINEERING a Division of
CQ ENGINEERING a Division of TECHNICAL INNOVATION ENGINEERING INSPECTION The CQ Group, LLC A Full Service Engineering Firm Specializing in High Tech Design and Innovation for Industrial and Manufacturing
More informationPressure Piping Construction Requirements
the pressure equipment safety authority Pressure Piping Construction Requirements AB 518 Edition 8, Revision 0 Issued 2017-08-24 Table of Contents FOREWORD... 1 1.0 SCOPE OF THIS DOCUMENT... 2 2.0 DEFINITIONS
More informationwww.flexonics.com 1 800 854 2553 Senior Flexonics Pathway Division 2400 Longhorn Industrial Dr. New Braunfels, Texas 78130 Tel Int: 1 830 629 8080 Fax Int: 1 830 629 6899 E-mail: sales@pathway.flexonics.com
More informationUniversity of Delaware
SECTION 22 05 00_COMMON WORK FOR PLUMBING SYSTEM University Contact: Energy & Engineering Group (302) 831-1744 Part 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Start up 2. Factory Training 3. Quality
More informationTUV / IICS 3.1 CERTIFIED WELDING INSPECTOR & API 577 WELDING INSPECTION & METALLURGY
LAST UPDATED 06-04-2018 TUV / IICS 3.1 CERTIFIED WELDING INSPECTOR & API 577 WELDING INSPECTION & METALLURGY COURSE DURATION: 7 DAYS ARE YOUR INSPECTORS / ENGINEERS PREPARED TO DEAL WITH THE RISING DEMAND
More informationAustralian Standard. Pressure equipment Examination and testing AS Reconfirmed 2016
AS 4037 1999 Reconfirmed 2016 Australian Standard Pressure equipment Examination and testing This Australian Standard was prepared by Committee ME/1, Pressure Equipment. It was approved on behalf of the
More informationWATERWORKS SERVICES WORKER I WATERWORKS SERVICES WORKER II WATERWORKS SERVICES WORKER III
WATERWORKS SERVICES WORKER I WATERWORKS SERVICES WORKER II WATERWORKS SERVICES WORKER III Class specifications are intended to present a descriptive list of the range of duties performed by employees in
More informationConformity Assessment. Dan Cheetham BPV Topics of Interest 2016 Certification 360
Conformity Assessment Dan Cheetham BPV Topics of Interest 2016 Certification 360 BPV Requirements Boiler and Pressure Vessel Requirements (Quality Control Programs, Materials, Examination & Inspection,
More informationJuly 2017 SC 3 Attachments
Table of Contents Attachment Page 1 July 2017 SC 3 Attachments SC 3 Roster July 2017.pdf 2 IN16-0401 Disapproved 3-27-17 3 IN16-0401 Letter Ballot Comments 3-27-17 5 17-135 Petersen 5-2-17 6 17-141 Chaine
More informationBODY OF KNOWLEDGE API-653 ABOVEGROUND STORAGE TANK INSPECTOR CERTIFICATION EXAMINATION
BODY OF KNOWLEDGE API-653 ABOVEGROUND STORAGE TANK INSPECTOR CERTIFICATION EXAMINATION October 2009 (Replaces November 2008) API Authorized Aboveground Storage Tank Inspectors must have a broad knowledge
More informationELECTRICAL INSPECTION BULLETIN B Installation and Inspection Requirements for Street and Roadway Lighting Systems. (Effective 2015/11/15 )
Scope This document covers the installation and inspection requirements for Street and that are installed and maintained within the jurisdiction of the Nova Scotia Power Incorporated (NSPI) inspection
More informationPART UIG THE ASME CODE FOR IMPREGNATED GRAPHITE PRESSURE VESSELS
PART UIG THE ASME CODE FOR IMPREGNATED GRAPHITE PRESSURE VESSELS Presented by: Ed Soltow Engineering and Design Manager SGL Carbon Technic LLC Member ASME Standards Committee on Pressure Vessels (BPV VIII)
More informationBOILERS AND PRESSURE VESSELS ACT REGULATIONS
c t BOILERS AND PRESSURE VESSELS ACT REGULATIONS PLEASE NOTE This document, prepared by the Legislative Counsel Office, is an office consolidation of this regulation, current to November 28, 2015. It is
More informationREGULATOR SPECIALIST. Position Summary
Position Summary Outlined in this document is the position description for the Regulator Specialist and various responsibilities. Job attributes and performance expectations are also defined. (Detailed
More informationWELDING ENGINEERING FABRICATION
WELDING ENGINEERING FABRICATION Safety Our safety department is structured for optimal safety performance, communication and coverage. Safety is our top priority Our management team has over 280 years
More informationREFERENCE SYLLABUS. for WELDING EXAMINER & WELDING EXAMINER IN TRAINING CERTIFICATES OF COMPETENCY EXAMINATIONS
WELDING EXAMINER & CERTIFICATES OF COMPETENCY S AB-94 Edition 1, Revision 6, 2016-05-01 This syllabus is being phased out and will be discontinued on April 30, 2018. GENERAL INFORMATION INTRODUCTION: This
More informationBolt-On Products & Systems
Bolt-On Products & Systems Today, ControHeat jackets are operating successfully in more than 50,000 applications worldwide. Continuous product improvement combined with a significant increase in demand
More information"Welder Certification"
"Welder Certification" The purpose of this presentation is to introduce you to the various aspects of welder certification. This is not intended to cover all of the requirements for certification but only
More informationUpstream Midstream Downstream
Upstream Midstream Downstream We Are Your Single Source Solution Provider. Main Headquarters: 1084 Cruse Ave., Broussard, LA 70518 Corporate Office: 1300 West Sam Houston Parkway South, Suite 345, Houston,
More informationBODY OF KNOWLEDGE API-570 AUTHORIZED PIPING INSPECTOR CERTIFICATION EXAMINATION
BODY OF KNOWLEDGE API-570 AUTHORIZED PIPING INSPECTOR CERTIFICATION EXAMINATION 2018 (Replaces February 2017) API Authorized Piping Inspectors must have a broad knowledge base relating to maintenance,
More informationACCREDITATION OF FITTING MANUFACTURERS
ACCREDITATION OF FITTING MANUFACTURERS TSSA GUIDE FOR REVIEW TEAMS The Technical Standards and Safety Authority Boilers and Pressure Vessels Safety Division 3300 Bloor Street West 14th Floor, Centre Tower
More informationProvincial Railway Guides Section:
Safety management plans are intended to outline and document the safety policies and operating procedures put in place by a railway and establish a system for managing safety for all aspects of the railway
More informationFrazier Reliability Solutions
Frazier Reliability Solutions Mechanical Integrity Audit Checklist Location: Completed By: Date: MI Program Management Yes No Does the company and/or site have a documented MI policy? Does the MI program
More informationBUILDING INSPECTOR I/II
BUILDING INSPECTOR I/II Class specifications are intended to present a descriptive list of the range of duties performed by employees in the class. Specifications are not intended to reflect all duties
More informationGMP Inspection Process. Types of GMP Inspection. Module 18 Slide 1 of 14 WHO - EDM
GMP Inspection Process Types of GMP Inspection Module 18 Slide 1 of 14 WHO - EDM Objectives 1. To review the different types of inspection 2. To examine when each is appropriate 3. To discuss inspections
More informationWATER DISTRIBUTION WORKER I WATER DISTRIBUTION WORKER II
CITY OF ROSEVILLE WATER DISTRIBUTION WORKER I WATER DISTRIBUTION WORKER II DEFINITION To perform a variety of semi-skilled and skilled tasks in the construction, maintenance, and repair of water distribution
More informationECONOMIZER ECM. Turnkey Price Installed: $115,295
ECONOMIZER ECM Turnkey Price Installed: $115,295 PRICE INSTALLED PER INVESTMENT GRADE AUDIT. CALCULATED ANNUAL SAVINGS OF $29,027.51 WITH A SIMPLE PAYBACK OF 3.97 YEARS. (SEE ATTACHED SAVINGS CALCULATIONS)
More informationEQUIPMENT FABRICATION MUST ALWAYS START WITH A CODE COMPLIANT DESIGN
THE PRESSURE NEWS Volume 17, Issue 3, September 2012 IN THIS ISSUE: Equipment Fabrication must Always start with a Code Compliant Design... 1 Alberta Provincial Power Engineer Certificate... 2 Standardization
More informationWelding Performance Qualification Test Administrators GUIDE FOR APPLICANTS
BRITISH COLUMBIA SAFETY AUTHORITY Welding Performance Qualification Test Administrators GUIDE FOR APPLICANTS Prepared by: Ed Hurd P.Eng. Provincial Safety Manager, Boilers Date: March 2, 2012 Controlled
More informationPRESSURE WELDERS REGULATION
Province of Alberta SAFETY CODES ACT PRESSURE WELDERS REGULATION Alberta Regulation 169/2002 With amendments up to and including Alberta Regulation 103/2014 Office Consolidation Published by Alberta Queen
More informationCROSS CONNECTION CONTROL PROGRAM
CROSS CONNECTION CONTROL PROGRAM I. PURPOSE Cross- connections between public water supplies and non-potable sources of contamination represent one of the most significant threats to health in the water
More informationLockout/Tagout Program
Lockout/Tagout Program 6600-2.0 Associated OHS Process: General Industry & Construction Safety The master copy of this document resides in electronic format. Printed copies of this document are for convenience
More informationList of forms CLAP/WGP by keyword - 97/23/EC
List of forms CLAP/WGP by keyword - 97/23/EC Keywords CLAP Adopted by WGP Adopted by number CLAP number WGP Subject accumulator 11 24/03/2000 1/19 24/03/2000 Scope - Hydraulic and pneumatic transmissions
More informationTechnical Committee on Highway Tanks and TC Portable Tanks for the Transportation of Dangerous Goods ix
Canadian Standards Association Highway tanks and TC portable tanks for the transportation of dangerous goods Contents Technical Committee on Highway Tanks and TC Portable Tanks for the Transportation of
More information1 Schedule A of New Brunswick Regulation under the Boiler and Pressure Vessel Act is amended
1 NEW BRUNSWICK REGULATION under the Boiler and Pressure Vessel Act 1 Schedule A of New Brunswick Regulation 84-177 under the Boiler and Pressure Vessel Act is amended (a) by repealing section 1 and substituting
More informationUniversity of Delaware
SECTION 23 05 00_COMMON WORK FOR HVAC SYSTEMS University Contact: Energy & Engineering Group (302) 831-1744 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Start up 2. Factory Training 3. Quality Control
More informationIndustrial Pretreatment Program Grease Abatement Requirements for Food Service Establishments (FSEs)
Public Works Department Environmental Division Industrial Pretreatment Program Meridian City Hall, Suite 204 33 E Broadway Avenue Meridian, Idaho 83642 Industrial Pretreatment Program Grease Abatement
More informationCAEAL - AGM Nova Scotia s Approach to Drinking Water Quality Monitoring for Public Supplies. Judy MacDonald June 17, 2005
CAEAL - AGM 2005 Nova Scotia s Approach to Drinking Water Quality Monitoring for Public Supplies Judy MacDonald June 17, 2005 Environment and Labour Today s s Presentation Welcome to Halifax! Background
More informationTraining Certification Categories
Training Certification Categories Residential Residential Building Inspector structures are free from hazardous structural conditions and comply with the UCC. Duties include inspection of footings and
More informationGUIDE FOR ASME REVIEW TEAM LEADERS FOR REVIEW OF APPLICANTS FOR ASME CERTIFICATES OF AUTHORIZATION H (Cast Iron/Cast Aluminum)
GUIDE FOR ASME REVIEW TEAM LEADERS FOR REVIEW OF APPLICANTS FOR ASME CERTIFICATES OF AUTHORIZATION H (Cast Iron/Cast Aluminum) The American Society of Mechanical Engineers Two Park Avenue New York, NY
More information"Welder Certification"
"Welder Certification" The purpose of this presentation is to introduce you to the various aspects of welder certification. This is not intended to cover all of the requirements for certification but only
More informationBTT : 1 autoclave bin
3' dia x 3' long (NB#195) 3' ft. diameter, 3' ft. length, 75 PSI pressure, 500 Deg. F temperature Contact: Pietro Wooldridge Phone: 606-677-2616 BTT : 1 autoclave bin 1.1.0 BONDTECH AUTOCLAVE/STERILIZER
More information