TEST REPORT. Rendered to: All Weather Insulated Panels Vacaville, California. PRODUCT TYPE: Roofing Panels SERIES/MODEL: SR Series

Transcription

1 Architectural Testing TEST REPORT Report No.: C Rendered to: All Weather Insulated Panels Vacaville, California PRODUCT TYPE: Roofing Panels SERIES/MODEL: SR Series Title Summary of Results Air psf 0.01 cfm/ft 2 Water Penetration Resistance Test Pressure psf Reference must be made to Report No. C dated 03/12/13 for complete test specimen description and detailed test results.

2 Page 1 of Report Issued To: All Weather Insulated Panels 929 Aldridge Road Vacaville, California Test Laboratory: Architectural Testing, Inc East Jensen Avenue Fresno, California (559) Project Summary: 3.1 Product Type: Roofing Panels 3.2 Series/Model: SR 3.3 Compliance Statement: Results obtained are tested values and were secured by using the designated test methods. Test specimen description and results are reported herein. 3.4 Test Date: 02/19/ Test Record Retention End Date: All test records for this report will be retained until March 12, Test Location: Architectural Testing, Inc. test facility in Fresno, California. 3.7 Test Sample Source: The test specimen was provided by the client. Representative samples of the test specimen will be retained by Architectural Testing for a minimum of four years from the test completion date. 3.8 Drawing Reference: The test specimen drawings have been reviewed by Architectural Testing and are representative of the test specimen reported herein. Test specimen construction was verified by Architectural Testing per the drawings located in Appendix B. Any deviations are documented herein or on the drawings. 3.9 List of Official Observers: Name Company Brian Ng David Douglass All Weather Insulated Panels Architectural Testing, Inc.

3 Page 2 of Test Methods: ASTM E 1646, Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference (in accordance with paragraphs 11.5, 11.6 and 11.7) ASTM E 1680, Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems (in accordance with Paragraphs 11.4, 11.5 and 11.6) Note 1: ASTM E 1646 is a specialized adaptation of Test Method E 331. Note 2: ASTM E 1680 is a specialized adaptation of Test Method E Test Specimen Description: 5.1 Product Sizes: Overall Area: Width Height 7.43 m² (80.0 ft 2 ) millimeters inches millimeters inches Overall size Construction: The SR Series foam insulated sheet metal roofing panels measured 3-1/4" thick with standing seams rising 2" above the top face of the panel. The mock-up consisted of two (2) full-sized roof panels measuring 96" long by 40" wide and two (2) half-sized panels cut in two pieces approximately 20" in width mounted at each edge of the assembly. A test buck was constructed of nominal 2 x 10 Douglas fir lumber. Three (3) 2 x 4 supports were attached the test buck, one at each end and one at mid-span. Additional wood blocks were attached to the supports at each anchor location. The three panelto-panel joints were secured to the supports with three (3) stainless steel anchor clips at each joint. Each anchor clip was secured with three (3) #8 x 3" Phillips flat head wood screws. A foam gasket was employed at the underside of each clip. The top lip of each panel joint was sealed with Schnee-Morehead SM5430 and crimped together. The perimeter of the mock-up was sealed to the wood test buck with Dow Corning 791 sealant.

4 Page 3 of Test Results: The temperature during testing was 11 C (52 F). The results are tabulated as follows: Title of Test Results Air Leakage per ASTM E 1680, at 1.57 psf 0.0 L/s/m 2 (0.00 cfm/ft 2 ) 0.0 L/s/m at 6.27 psf 2 (0.00 cfm/ft 2 ) 0.0 L/s/m at psf 2 (0.00 cfm/ft 2 ) Water Penetration per ASTM E 1646, at psf Pass at psf Pass General Note: All testing was performed in accordance with the referenced standard(s). Roof panels were tested in the horizontal position (zero roof slope).

5 Test Report No.: C Page 4 of 4 Architectural Testing will service this report for the entire test record retention period. Test records that are retained such as detailed drawings, datasheets, representative samples of test specimens, or other pertinent project documentation will be retained by Architectural Testing, Inc. for the entire test record retention period. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimen(s) tested. This report may not be reproduced, except in full, without the written approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, Inc. David Douglass Project Manager JO:DD: ms Tyler Westerling Project Engineer Attachments (pages): This report is complete only when all attachments listed are included. Appendix-A: Photographs (3) Appendix-B: Drawings (2) This report produced from controlled document template ATI 00479, issued 01/27/12.

6 Appendix A Photographs

7 Photo No. 1 Installation

8 Photo No. 2 Completed Assembly

9 Photo No. 3 Water Infiltration Test

10 Appendix B Drawings

11

12