PUBLIC SERVICE COMMISSION: HYDERABAD. NOTIFICATION NO.09/2016, Dt.30/09/2016

Size: px

Start display at page:

Download "PUBLIC SERVICE COMMISSION: HYDERABAD. NOTIFICATION NO.09/2016, Dt.30/09/2016"

Toby Tyler
5 years ago
Views:

thereto, as per the specifications in the relevant service rules and as per the indent received from the Department as on the date of notification.

1 1 ANDHRA PRADESH PUBLIC SERVICE COMMISSION: HYDERABAD NOTIFICATION NO.09/2016, Dt.30/09/2016 ASSISTANT ENGINEERS IN VARIOUS ENGINEERING SUB-ORDINATE SERVICES (GENERAL RECRUITMENT) EDUCATIONAL QUALIFICATIONS: Applicant must possess the qualifications as detailed below or equivalent thereto, as per the specifications in the relevant service rules and as per the indent received from the Department as on the date of notification. Post Code Name of the Post Educational Qualifications A Bachelor s Degree or Diploma in Civil Engineering of a University in India established or Municipal Assistant incorporated by or under a Central Act, State Act or 01 Engineer (Civil) in A.P PH an Institution Recognized by the University Grants & ME dept., Commission / AICTE or a Pass in Sections A and B of AMIE (India) Examination in Civil Engineering. 02 Assistant Engineer (Civil) in A.P G.W Dept Diploma in Civil Engineering or any other equivalent qualification.

2 2 03 Assistant Engineer (PH) in PH & ME Dept., 1. A Degree in B.E. Civil or Mechanical of a University established or incorporated by or under a Central Act, State or Provincial Act or Institution recognized by the UGC. OR 2. B.Sc. (Engineering) degree of the Benaras Hindu University. OR 3. A pass in section A and B of the AMIE (India) Civil Examination. OR 4. LCE Diploma or any other equivalent Diploma of any recognized Institute. OR 5. LME. Diploma of any recognized Institute. OR 6. LSE, Diploma awarded by the State Board of Technical Education and Training. (Substituted as per G.O.Ms.No.690 MA,dt w.e.f Provided that the recruitment of persons with LME Diploma/ Degree in Mechanical Engineering of any Institution recognized by the Government in any year shall not exceed 10% of the total number of estimated vacancies in that year. ( amended G.O. Ms. No. 272, MA, Dt. 07/06/1976 w. e. f, Dt.28/02/1972) Provided further that, candidates possessing the qualifications in terms (4) to (6) above will be recruited only if candidates possessing the

3 qualifications in terms (1) to (3) are not available. (G.O. Ms. No. 690, MA, Dt. 30/09/1972 w. e. f, Dt.08/07/1964) SCHEME AND SYLLABUS FOR THE POSTS OF ASSISTANT ENGINEERS IN VARIOUS ENGINEERING SUB-ORDINATE SERVICES SCHEME SCREENING TEST WRITTEN (OBJECTIVE TYPE) EXAMINATION Screening test : Section-I General Studies & Mental Ability, 50 Questions and 50 Marks Section-II Civil/ Mechanical (Common) (Diploma Standard) 100 Questions and 100 Marks Max. Marks No. of Questions DURATION 150 Marks 150 Questions 150 Minutes Total 150Marks 150 Questions 150 Minutes MAIN WRITTEN (OBJECTIVE TYPE) EXAMINATION Max. Marks No. of Questions DURATION PAPER-1 General Studies & Mental Ability 150 Marks 150 Questions 150 Minutes PAPER-2 Subject:- Civil/ Mechanical (Common) (Diploma Standard) 150 Marks 150 Questions 150 Minutes

4 3 TOTAL 300 Marks SYLLABUS FOR SCREENING TEST TO THE POST OF ASSISTANT ENGINEERS IN VARIOUS ENGINEERING DEPARTMENTS SECTION -I 50 Questions 50 Marks GENERAL STUDIES & MENTAL ABILITY 1. Events of national and international importance. 2. Current affairs- international, national and regional. 3. Basics of General Science and their relevance to the day to day life. Current developments in science, technology and information technology 4. History of Modern India with emphases upon Indian national movement. 5. Economic development in India since independence. 6. Logical reasoning, analytical ability and data interpretation. 7. Basic things about Disaster management (CBSE-VIII & IX Standard). 8. Geography of India with focus on A.P 9. Indian Constitution and Polity. 10. Sustainable Development and Environmental Protection 11. Bifurcation of Andhra Pradesh and its Administrative, Economic, Social, Cultural, Political, and legal implications/problems, including a). Loss of capital city, challenges in building new capital and it s financial implications. b). Division and rebuilding of common Institutions. c). Division of employees, their relocation and nativity issues. d). Effect of bifurcation on commerce and entrepreneurs. e). Implications to financial resources of state government. f). Task of post-bifurcation infrastructure development and opportunities for investments. g).socioeconomic, cultural and demographic impact of bifurcation. h).impact of bifurcation on river water sharing and

5 consequential issues. i). AP REORGANISATION ACT, 2014 on AP and the arbitrariness of certain provisions. SECTION-II 100 Questions 100 Marks SOLID MECHANICS: (COMMON FOR CIVIL / MECHANICAL) Forces: Different types of forces, gravitational, frictional, axial, tensile or compressive. Law of Parallelogram and triangle of forces, polygon of forces, problems. Centre of gravity and moment of inertia. Simple plane figures, Simple machines, law of machine, Mechanical advantage, velocity ratio and efficiency, wheel and axle, pulleys and simple screw jack-problems. Simple Stresses and strailns: Different types of stresses and strains, stress-strain diagram for ductile materials. Factor of safety, ultimate strength and working strength, elastic constants, Poisson ratio. Deformations, volume changes. Relations between elastic constants. Hooke's Law. Compound rods, temperature stresses, strain energy, impact loading. Riveted and welded joints, different modes of failures, efficiency of joints, thin cylindrical shells, longitudinal and circumferential stresses and volume changes. Shear force and bending moment diagrams for simply supported, over hanging and cantilever beams. Relation between intensity of loading, shear force and bending moment.

6 4 Theory of simple bending: Assumptions, basic flexure formula, bending stresses, modulus of section, moment of resistance. Circular bending. Distribution of shear stress in common structural sections. Deflection in cantilever and simply supported beams under simple loadingpropped cantilever beams subjected to simple loading, determination of reaction. SF and BM diagrams. Simple plane and pin-jointed trusses: Stresses by method of joints and method of sections. Torsion: Assumptions, basic formula of torsion, power transmission by shafts of uniform circular sections close-coiled springs, strain-energy in simple beams and shafts, sudden and impact loading. Principal stresses and principal planes. Moher's circle of stress. Thin cylinders under internal pressure stresses and volume changes. Columns and struts: Direct and bending stresses, core of section. Short and long columns under axial loading-various end-conditions. Euler and Rankine formulae, Slenderness ratio, simple built-up columns. FLUID MECHANICS: Introduction: Scope of hydraulics in Engineering. Definition and properties of fluid. Fluid pressure and its measurement: Atmospheric pressure, Gauge pressure and absolute pressure. Piezometer, Manometer-U-tube, Inverted U-tube, and differential manometers. Pressure on plane surface immersed in liquid-horizontal, vertical and inclined plane surface. Flow of fluids: Type of flow-uniform flow, non-uniform flow, streamline flow, Turbulant flow, steady flow and unsteady flow, Energies in fluid motion-datum head, pressure head and velocity head. Total energy of fluid in motion - Bernoulli s theorem. Practical application of Bernoulli's theorem - flow measurement- pitot tube venturimeter - Orificemeter. Flow through orifices and Mouth Pieces: Definition of orifice, types of orifices, Vena contracta, coefficient of velocity, coefficient of contraction, coefficient of

7 discharge. Submerged and partially submerged orifices. Flow through orifices under variable heads - Time of emptying a rectangular tank through orifices. Mouth pieces - different types of problems. Notches and Weirs: Definition of notch, types of notches - Rectangular notch, Tringular notch and trapezoidal notch. Discharge over a rectangular, triangular and a trapezoidal notches. Flow through pipes: Major and minor losses - Loss of head at entrance, loss of head due to sudden enlargement, due to sudden contraction, loss of head at exit of the pipe. Frictional loss in pipe-chezy formula and Daycy's formula. Hydraulic gradient and total energy line. Discharge through parallel pipes and branched pipes connected to a reservoir. Flow through syphon pipe. Hydraulic transmission of power-flow through nozzle at the end of a pipe linediameter of nozzle for Max H.P. available. Water hammer and its effect. Laminar and turbulent flow in pipes-critical velocity and Reynold number. Impact of jets: Formulae for the force of jet on a fixed vertical flat plate, fixed inclined flat plates, moving flat plates, series of flat plates fixed on the rim of a wheel. Force of jet striking at the centre and at the top of a fixed curved blade and moving curved blade, velocity triangles. Work done, power and efficiency in the above cases. Simple problems. Water turbines: Introduction to water turbines. Use of water turbines in Hydroelectric power stations line sketch showing layout of hydro-electric power plant with head race, dam, sluice gate, pen stock turbine, generator and tail race. Classification of turbines - impulse and reaction turbines brief sub-classification of axial, radial and tangential flow type. Pelton wheel, Francis turbine and Kaplan turbine, power and efficiency of turbines.

8 5 Centrifugal pump: Installation, mountings and other accessories. Priming of centrifugal pump. Efficiency, cavitation. Simple problems on work, power and efficiency. SYLLABUS FOR MAIN EXAMINATION FOR THE POSTS OF ASSISTANT ENGINEERs IN VARIOUS ENGINEERING DEPARTMENTS PAPER -I GENERAL STUDIES & MENTAL ABILITY 1. Events of national and international importance. 2. Current affairs- international, national and regional. 3. Basics of General Science and their relevance to the day to day life. Current developments in science, technology and information technology 4. History of Modern India with emphases upon Indian national movement. 5. Economic development in India since independence. 6. Logical reasoning, analytical ability and data interpretation. 7. Basic things about Disaster management (CBSE-VIII & IX Standard). 8. Geography of India with focus on A.P 9. Indian Constitution and Polity. 10. Sustainable Development and Environmental Protection 11. Bifurcation of Andhra Pradesh and its Administrative, Economic, Social, Cultural, Political, and legal implications/problems, including a). Loss of capital city, challenges in building new capital and it s financial implications. b). Division and rebuilding of common Institutions. c). Division of employees, their relocation and nativity issues. d). Effect of bifurcation on commerce and entrepreneurs. e). Implications to financial resources of state government. f). Task of post-bifurcation infrastructure development and opportunities for investments. g).socioeconomic, cultural and demographic impact of bifurcation. h).impact of bifurcation on river water sharing and consequential issues. i). AP REORGANISATION ACT, 2014 on AP and the arbitrariness of

9 certain provisions. SOLID MECHANICS: PAPER-2 (COMMON FOR CIVIL / MECHANICAL) Forces: Different types of forces, gravitational, frictional, axial, tensile or compressive. Law of Parallelogram and triangle of forces, polygon of forces, problems. Centre of gravity and moment of inertia. Simple plane figures, Simple machines, law of machine, Mechanical advantage, velocity ratio and efficiency, wheel and axle, pulleys and simple screw jack-problems. Simple Stresses and strailns: Different types of stresses and strains, stressstrain diagram for ductile materials. Factor of safety, ultimate strength and working strength, elastic constants, Poisson ratio. Deformations, volume changes. Relations between elastic constants. Hooke's Law. Compound rods, temperature stresses, strain energy, impact loading. Riveted and welded joints, different modes of failures, efficiency of joints, thin cylindrical shells, longitudinal and circumferential stresses and volume changes. Shear force and bending moment diagrams for simply supported, over hanging and cantilever beams. Relation between intensity of loading, shear force and bending moment.

10 6 Theory of simple bending: Assumptions, basic flexure formula, bending stresses, modulus of section, moment of resistance. Circular bending. Distribution of shear stress in common structural sections. Deflection in cantilever and simply supported beams under simple loadingpropped cantilever beams subjected to simple loading, determination of reaction. SF and BM diagrams. Simple plane and pin-jointed trusses: Stresses by method of joints and method of sections. Torsion: Assumptions, basic formula of torsion, power transmission by shafts of uniform circular sections close-coiled springs, strain-energy in simple beams and shafts, sudden and impact loading. Principal stresses and principal planes. Moher's circle of stress. Thin cylinders under internal pressure stresses and volume changes. Columns and struts: Direct and bending stresses, core of section. Short and long columns under axial loading-various end-conditions. Euler and Rankine formulae, Slenderness ratio, simple built-up columns. FLUID MECHANICS: Introduction: Scope of hydraulics in Engineering. Definition and properties of fluid. Fluid pressure and its measurement: Atmospheric pressure, Gauge pressure and absolute pressure. Piezometer, Manometer-U-tube, Inverted U-tube, and differential manometers. Pressure on plane surface immersed in liquid-horizontal, vertical and inclined plane surface. Flow of fluids: Type of flow-uniform flow, non-uniform flow, streamline flow, Turbulant flow, steady flow and unsteady flow, Energies in fluid motion-datum head, pressure head and velocity head. Total energy of fluid in motion - Bernoulli s theorem. Practical application of Bernoulli's theorem - flow measurement- pitot tube venturimeter - Orificemeter.

11 Flow through orifices and Mouth Pieces: Definition of orifice, types of orifices, Vena contracta, coefficient of velocity, coefficient of contraction, coefficient of discharge. Submerged and partially submerged orifices. Flow through orifices under variable heads - Time of emptying a rectangular tank through orifices. Mouth pieces - different types of problems. Notches and Weirs: Definition of notch, types of notches - Rectangular notch, Tringular notch and trapezoidal notch. Discharge over a rectangular, triangular and a trapezoidal notches. Flow through pipes: Major and minor losses - Loss of head at entrance, loss of head due to sudden enlargement, due to sudden contraction, loss of head at exit of the pipe. Frictional loss in pipe-chezy formula and Daycy's formula. Hydraulic gradient and total energy line. Discharge through parallel pipes and branched pipes connected to a reservoir. Flow through syphon pipe. Hydraulic transmission of power-flow through nozzle at the end of a pipe linediameter of nozzle for Max H.P. available. Water hammer and its effect. Laminar and turbulent flow in pipes-critical velocity and Reynold number. Impact of jets: Formulae for the force of jet on a fixed vertical flat plate, fixed inclined flat plates, moving flat plates, series of flat plates fixed on the rim of a wheel. Force of jet striking at the centre and at the top of a fixed curved blade and moving curved blade, velocity triangles. Work done, power and efficiency in the above cases. Simple problems. Water turbines: Introduction to water turbines. Use of water turbines in Hydroelectric power stations line sketch showing layout of hydro-electric power plant with head race, dam, sluice gate, pen stock turbine, generator and tail race. Classification of turbines - impulse and reaction turbines

12 7 brief sub-classification of axial, radial and tangential flow type. Pelton wheel, Francis turbine and Kaplan turbine, power and efficiency of turbines. Centrifugal pump: Installation, mountings and other accessories. Priming of centrifugal pump. Efficiency, cavitation. Simple problems on work, power and efficiency. SECRET ARY S d / -

2/25, Ansari Road, Darya Ganj, New Delhi

2/25, Ansari Road, Darya Ganj, New Delhi B.E.(Mechanical), M.I.E(India) M.B.M. Engineering College, Jodhpur M.E. (Structural), Delhi University B.E.(Civil) M.B.M. Engineering College, Jodhpur (AN ISO 9001:2008 Certified Company) VAYU EDUCATION