IMPROVED CALORIFIC CAPACITY RESERVE:

Transcription

1 660 DESCRIPTION: is a high quality Heat Transfer Lubricant of superior thermal stability. It is engineered to the highest operating standards to resist sludging tendencies common with low quality oils. is produced from an exceptionally fine, low viscosity base oil. This improves heat transfer properties immensely and also provides superior thermal stability and resistance to thermal cracking at elevated temperatures. INCREASED THERMAL STABILITY: Ordinary heat transfer oils lack the stability at temperature extremes to prevent sludging and deposition of oil solids on internal oil-side parts. however features a select range of additives that provide maximum thermal stability at elevated temperatures through thousands of cyclic temperature cycles (start up/shut downs). These special additives minimize deposits to inconsequential and nondamaging proportions. Proprietary dispersants also control sludge which would otherwise decrease heat transfer rates. The highly improved thermal efficiency of all but eliminates the necessity to frequently drain, dispose and replenish heat transfer oil systems. IMPROVED CALORIFIC CAPACITY RESERVE: ensures rapid and increased efficiency heat transfer to the process environment. lts high viscosity index minimizes viscosity variations during temperature climbs and drops. Heat transfer rate is properly controlled for the first time due to 's stable viscosity. Copyright, All rights reserved. (BSI 5750 or equivalent source) Magna Industrial reserves the right to modify or change this product for OPIM660-1 Version 1.0 Revision 1.0 Rev. Date: 8 January, 2003 Reference: LUN purposes of improving its performance characteristics.

2 features extremely low volatility due to special choice petroleum fraction constituents. lts low vapour pressure and extended boiling point enable heat transfer systems to operate at both low pressures and elevated temperatures. DECREASED OPERATIONAL COSTS: 's lower viscosity at all operating temperatures lower energy requirements for pumping and circulation purposes. Smaller pumps can be used or alternately, bigger existing pumps can be run at lower and more economical speeds due to the low load presented by at start-up. is completely safe under normal handling conditions and is completely non-toxic. USES: is engineered for use in closed heat transfer systems equipped with expansion tanks and operating to 320 C (608 F). It is ideal as a heat transfer medium in processing industries such as plastics, waxes, resin, fiberboard, varnish, asphalt, grease, rubber, soap and pharmaceuticals manufacturing. enables extremely close process temperature control and reduces the risk of fire as no direct heat is exposed to flammable processing materials. The uniform transfer of heat provided by reduces the possibility, of overheating which is a common problem in processing industries. is also highly effective as a quenching oil and is recommended for heat-treating steels due to its high heat capacity, good heat conductivity, low viscosity, high thermal stability and high flash point. APPLICATION: The circulation system must be totally enclosed. This will help prevent fluid contamination, losses from vaporization and excessive oxidation. In order to maximize operating life, the following should be observed: Keep system clean, enclosed and free of air leaks. Ensure turbulent fluid flow in heat transfer tubes to maximize heat transfer rate. Maintain flow rates at between 1.5 to 3 metres (5 feet to 12 feet) per second to reduce localized overheating. Copyright, All rights reserved. (BSI 5750 or equivalent source) Magna Industrial reserves the right to modify or change this product for OPIM660-2 Version 1.0 Revision 1.0 Rev. Date: 8 January, 2003 Reference: LUN purposes of improving its performance characteristics.

3 TYPICAL DATA: TEST ASTM TEST METHOD ISO Viscosity Grade D Appearance Visual Amber Density, 15 C D Viscosity, 40 C D C D Viscosity Index D Pour Point, C ( F) D-97-9 (14) Flash Point, COC, C ( F) D (512) Fire Point, C ( F) D (555) Total Base Number, mg KOH/g D Foaming Characteristics - All Sequences, After Settling D-892 Nil Carbon Residue, Conradson, % Mass* D Ash, Sulphated, % Mass D Calcium, % Mass AA * In excess of Ash Content THERMAL CHARACTERISTICS: Temperature, C ( F) 40 (104) 100 (212) 150 (302) 200 (392) 250 (482) 300 (570) 350 (662) Density, 15 C(60 F) Viscosity, cp cst Vapour Pressure, mm Hg Pa Specific Heat Capacity - kj/kg K Thermal Conductivity W/m K BTU/hr/ F/ft Copyright, All rights reserved. (BSI 5750 or equivalent source) Magna Industrial reserves the right to modify or change this product for OPIM660-3 Version 1.0 Revision 1.0 Rev. Date: 8 January, 2003 Reference: LUN purposes of improving its performance characteristics.

4 1/8 SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING 1.1. Product identifier Container size: 20 l 1.2. Relevant identified uses of the substance or mixture and uses advised against Application: Heat transfer oil 1.3. Details of the supplier of the safety data sheet Supplier: Manufacturer Responsible for safety data sheet authoring: 1.4. Emergency telephone number EU importer:.. Sovereign Lubricants (UK) Ltd, Crowtrees Lane, Rastrick, West Yorkshire, HD6 3LZ T: F: enquiries@sovereign-omega.co.uk Ωmega Manufacturing Division 1801, Guardian House 32 Oi Kwan Road Wanchai, Hong Kong Tel:(852) Fax:(852) magna@magnagroup.com Responsible for safety data sheet authoring. Any questions to the contents of this safety data sheet should be sent to: SDS_info@dhigroup.com SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the substance or mixture The product is classified:r52/53 Human health: Environment: 2.2. Label elements Prolonged or repeated contact with skin may cause redness, itching, irritation, eczema, skin cracking and oil acne. Degreasing to skin. The harmful effects may increase in used oil. Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Oil spills are generally hazardous to the environment. R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. S Other hazards PBT/vPvB: This material and its container must be disposed of as hazardous waste. Not relevant.

5 2/8 SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS The product contains: mineral oil (DMSO-content < 3%) and additives. 67/548/EEC: %: CAS-No.: EC No.: REACH Reg. No: Chemical name: Hazard classification: Notes: 0,01-0, Phenol, dodecyl-, branched Repr3;R62 Xi;R38 N;R50-53 GHS/CLP: %: CAS-No.: EC No.: REACH Reg. No: Chemical name: Hazard classification: Notes: 0,01-0, Phenol, dodecyl-, branched Repr. 2;H361f Skin Irrit. 2;H315 Aquatic Acute 1;H400 Aquatic Chronic 1;H410 References: The full text for all R-phrases and hazard statements are displayed in section 16. SECTION 4: FIRST AID MEASURES 4.1. Description of first aid measures Inhalation: Skin contact: Eye contact: Ingestion: Move into fresh air and keep at rest. In case of persistent throat irritation or coughing: Seek medical attention and bring these instructions. Remove contaminated clothing immediately and wash skin with soap and water. In case of rashes, wounds or other skin disorders: Seek medical attention and bring along these instructions. Immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyelids widely. If irritation persists: Seek medical attention and bring along these instructions. Immediately rinse mouth and drink plenty of water. Keep person under observation. If person becomes uncomfortable seek hospital and bring these instructions Most important symptoms and effects, both acute and delayed Symptoms/effects: See section 11 for more detailed information on health effects and symptoms Indication of any immediate medical attention and special treatment needed Medical attention/treatments: Not known.

6 3/8 SECTION 5: FIREFIGHTING MEASURES 5.1. Extinguishing media Extinguishing media: 5.2. Special hazards arising from the substance or mixture Specific hazards: 5.3. Advice for firefighters Protective equipment for fire-fighters: Small fires: Extinguish with carbon dioxide or dry powder. Larger fires: Extinguish with foam, carbon dioxide or dry powder. Do not use water jet as an extinguisher, as this will spread the fire. During fire, gases hazardous to health may be formed. Selection of respiratory protection for fire fighting: follow the general fire precautions indicated in the workplace. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions, protective equipment and emergency procedures Personal precautions: 6.2. Environmental precautions Environmental precautions: 6.3. Methods and material for containment and cleaning up Methods for cleaning up: 6.4. Reference to other sections Avoid inhalation of oil mist and contact with skin and eyes. Follow precautions for safe handling described in this safety data sheet. Do not discharge into drains, water courses or onto the ground. Absorb spillage with oil-absorbing material. Clean contaminated area with oil-removing material. References: For personal protection, see section 8. For waste disposal, see section 13. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for safe handling Safe handling advice: Technical measures: Technical precautions: Observe good chemical hygiene practices. Avoid prolonged and repeated contact with oil, particularly used oil. Always remove oil with soap and water or skin cleaning agent, never use organic solvents. Do not use oil-contaminated clothing or shoes, and do not put rags moistened with oil into pockets. Use work methods which minimise oil mist production. When working with heated oil, mechanical ventilation may be required Conditions for safe storage, including any incompatibilities Technical measures for safe storage: Storage conditions: 7.3. Specific end use(s) Specific use(s): No special precautions. Store in tightly closed original container. Not relevant.

7 4/8 SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control parameters No occupational exposure limit assigned Exposure controls Engineering measures: Personal protection: Respiratory equipment: Hand protection: Eye protection: Hygiene measures: Environmental Exposure Controls: Provide adequate ventilation and minimise the risk of inhalation of vapours and oil mist. Provide access to washing facilities incl. soap, skin cleanser and fatty cream. Personal protection equipment should be chosen according to the CEN standards and in discussion with the supplier of the personal protective equipment. In case of inadequate ventilation or risk of inhalation of oil mist, suitable respiratory equipment with combination filter (type A2/P3) can be used. Wear protective gloves. Nitrile gloves are recommended, but be aware that the liquid may penetrate the gloves. Frequent change is advisable. Other types of gloves can be recommended by the glove supplier. Risk of contact: Wear goggles/face shield. Wash hands after contact. Wash contaminated clothing before reuse. Not available. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on basic physical and chemical properties Appearance: Amber-coloured liquid Odour: Almost odourless. ph: Not relevant Boiling point: Not available Flash point: > 150 C Explosion limits: Not available Vapour pressure: Not available Relative density: ~0,9 Solubility: insoluble in water 9.2. Other information Other data: Kinematic viscosity: ~ 105 mm²/s (40 C)

8 5/8 SECTION 10: STABILITY AND REACTIVITY Reactivity Reactivity: Chemical stability Stability: None known Possibility of hazardous reactions Hazardous Reactions: Conditions to avoid Stable under normal temperature conditions. None known. Conditions/materials to avoid: Avoid heat Incompatible materials Incompatible materials: Hazardous decomposition products Hazardous decomposition products: Strong oxidising substances. None in particular. SECTION 11: TOXICOLOGICAL INFORMATION Information on toxicological effects The harmful effects may increase in used oil. Inhalation: Skin contact: Eye contact: Ingestion: Specific effects: Inhalation of oil mist or vapours formed during heating of the product will irritate the respiratory system and provoke coughing. Degreasing. Prolonged or frequent contact may cause redness, itching, irritation, eczema, skin cracking and oil acne. Splashes may irritate. May irritate and cause malaise. Prolonged or repeated contact with used oil may cause serious skin diseases, such as dermatitis and skin cancer.

9 6/8 SECTION 12: ECOLOGICAL INFORMATION Toxicity Ecotoxicity: Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Oil spills are generally hazardous to the environment Persistence and degradability Degradability: Bioaccumulative potential Bioaccumulative potential: Mobility in soil Mobility: The product contains a substance which is very toxic to aquatic organisms and which may cause long term adverse effects in the aquatic environment. EC50 (Daphnia: Daphnia magna)/48 hours: 0.01 < EC mg/l (Phenol, dodecyl-, branched) The product is expected to be slowly biodegradable. No data available on bioaccumulation. No data available Results of PBT and vpvb assessment PBT/vPvB: Other adverse effects Other adverse effects: Not relevant. None known. SECTION 13: DISPOSAL CONSIDERATIONS Waste treatment methods Dispose of waste and residues in accordance with local authority requirements. Waste is classified as hazardous waste. Waste from residues: EWC-code:

10 7/8 SECTION 14: TRANSPORT INFORMATION The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA, ADR/RID) UN number UN-No: UN proper shipping name Proper Shipping Name: Transport hazard class(es) Class: Packing group PG: Environmental hazards Marine pollutant: - Environmentally Hazardous substance: Special precautions for user Special precautions: - None known Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Transport in bulk: Not relevant. SECTION 15: REGULATORY INFORMATION Safety, health and environmental regulations/legislation specific for the substance or mixture National regulation: Chemical Safety Assessment CSA status: Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH), establishing a European Chemicals Agency, amending Directive 1999/45/EC and repealing Council Regulation (EEC) No 793/93 and Commission Regulation (EC) No 1488/94 as well as Council Directive 76/769/EEC and Commission Directives 91/155/EEC, 93/67/EEC, 93/105/EC and 2000/21/EC, including amendments. Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16 December 2008 on classification, labelling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006 with amendments. The Chemicals (Hazard Information and Packaging for Supply) Regulations 2009 (S.I 2009 No. 716). The Control of Substances Hazardous to Health Regulations 2002 (S.I 2002 No. 2677) with amendments. The List of Wastes (England) (Amendment) Regulations (SI 2005 No. 895). Not relevant.

11 8/8 SECTION 16: OTHER INFORMATION The user must be instructed in the proper work procedure and be familiar with the contents of these instructions. Handling of used oils: Protect health - avoid prolonged and repeated skin contact. Wash with soap and water. Protect the environment - do not pollute drains, water courses or the soil. Contact your local authority for any used oil disposal instructions. The following sections contain revisions or new statements: Omega Manufacturing Division 1801, Guardian House, 32 Oi Kwan Road Wanchai, Hong Kong Tel : (852) Fax : (852) Web site : The Omega Trade Mark is the property of ITW, Inc., and is used under licence by Magna Industrial Co. Limited. Wording of R-phrases/H-statements: R38 Irritating to skin. R50/53 Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. R62 Possible risk of impaired fertility. H315 H361f H400 H410 Causes skin irritation. Suspected of damaging fertility. Very toxic to aquatic life. Very toxic to aquatic life with long lasting effects. The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using the product in combination with any other product or any other process is the responsibility of the user. Made by DHI - Environment and Toxicology, Agern Allé 5, DK-2970 Hørsholm, Denmark.