ammo::lyser eco Spectrometer Probes Ionselective Probes Sensors Terminals System Configuration Monitoring Station Accessories & Infrastructure

Transcription

1 Messgeräte Sonstige Daten ammo::lyser eco s::can plug & measure measuring principle: ISE (ionselective electrodes) - without potassium compensation multiparameter probe ammo::lyser II eco: monitors NH4-N and temperature ammo::lyser III eco+: monitors additionally ammo::lyser III eco+no3-n: monitors additionally NO 3 -N ammo::lyser IV eco++no 3-N: monitors additionally and NO 3 -N long term stable, factory precalibrated automatic cleaning with compressed air easy & quick mounting and measurement directly in the media (InSitu) or in flow cell (monitoring station) operation via s::can terminals & s::can software compensation of disturbing influences - temperature and possible ideal for surface water, ground water and drinking water, also for applications in waste water minimal maintenance life time of membranes: typically 6 month (for applications <1mg/l NH 4 -N), resp. 1 to 2 years (for applications >1mg/l NH 4 -N) negligible operational cost because of long membrane life time and the possibility of changing each membrane separately recommended accessories part number article name F-11-ammo carrier ammo::lyser F-44-ammo flow cell for ammo::lyser F-50-2 system-panel for s::can ISE probes and s::can sensors C-210-sensor 10 m extension cable for s::can oxi::lyser and ammo::lyser B-44 cleaning valve 1

2 technical specification measuring principle ISE measuring range application mg/l NH 4 -N (factory precalibrated: mg/l NH 4 -N) resolution NH 4 -N: mg/l NH 4 -N: mg/l NH 4 -N: mg/l T: 0.1 C automatic compensation cross type E-532-eco: temperature sensitivities type E-532-eco-: temperature, type E-532-eco-NO 3 -N: temperature type E-532-eco-NO 3 -N-: temperature, precalibrated ex-works all parameters response time 10 sec. integration via con::lyte 1 con::lyte 2 con::lyte 4 con::nect con::stat power supply VDC power consumption (typical) 0.72 W interface connection to s::can sys plug, IP 68, RS485, 12 VDC terminals cable length 10 m surface water ammo::lyser II eco (NH 4, temp) ammo::lyser III eco+no 3 -N (NH 4, temp, NO 3 -N) ammo::lyser III eco+ (NH 4, temp, ) ammo::lyser IV eco+no 3 -N+ (NH 4, temp, NO 3 -N, ) cable type PU jacket 2x2x0.25 housing material stainless steel , POM-C, glas electrodes weight (min.) 2.7 kg dimensions (diameter x length) 60 x 326 mm operating temperature C storage temperature C operating pressure mbar installation / mounting submersed or in Bypass (flow cell) process connection G 1 1/2 outside flowrate 0.01 m/s (min.) 3 m/s (max.) protection class IP 68 automatic cleaning media: compressed air permissible pressure: bar air volume: liter per cleaning cleaning duration: seconds per cleaning cleaning interval: minutes, depending on application delay: seconds conformity - EMC EN :1992 EN :1992 EN :1987 EN :1987 conformity - safety EN :2001 typical concentration ranges for this application NH 4 -N NO 3 -N [] temperature [ C] part number min. 1 0 E-532-eco max min E-532-eco-NO 3 -N max min E-532-eco- max min E-532-eco-NO 3 - max N- 2

3 Messgeräte Sonstige Daten ammo::lyser pro s::can plug & measure measuring principle: ISE (ionselective electrodes) - with potassium compensation multiparameter probe ammo::lyser III pro: monitors NH4-N and temperature ammo::lyser IV pro+ monitors NH4-N, temperature, (with potassium compensation) ammo::lyser IV pro+no3-n monitors NH 4 -N, temperature und NO 3 -N (with potassium compensation) long term stable, factory precalibrated automatic cleaning with compressed air easy & quick mounting and measurement directly in the media (InSitu) or in flow cell (monitoring station) operation via s::can terminals & s::can software compensation of disturbing influences - temperature, and potassium possible ideal for surface water, ground water and drinking water, also for applications in waste water minimal maintenance life time of membranes: typically 6 month (for applications <1mg/l NH 4 -N), resp. 1 to 2 years (for applications >1mg/l NH 4 -N) negligible operational cost because of long membrane life time and the possibility of changing each membrane separately recommended accessories part number article name F-11-ammo carrier ammo::lyser F-44-ammo flow cell for ammo::lyser F-50-2 system-panel for s::can ISE probes and s::can sensors C-210-sensor 10 m extension cable for s::can oxi::lyser and ammo::lyser B-44 cleaning valve 3

4 technical specification measuring principle ISE measuring range application mg/l NH 4 -N (factory precalibrated: mg/l NH 4 -N) resolution NH 4 -N: mg/l NH 4 -N: mg/l NH 4 -N: mg/l T: 0.1 C automatic compensation cross type E-532-pro: temperature, K sensitivities type E-532-pro-: temperature,, K type E-532-pro-NO 3 -N: temperature, K precalibrated ex-works all parameters response time 10 sec. integration via con::lyte 1 con::lyte 2 con::lyte 4 con::nect con::stat power supply VDC power consumption (typical) 0.72 W interface connection to s::can sys plug, IP 68, RS485, 12 VDC terminals cable length 10 m cable type PU jacket 2x2x0.25 surface water ammo::lyser II pro (NH 4, K, temp) ammo::lyser IV pro+no 3 -N (NH 4, NO 3 -N, K, temp) ammo::lyser IV pro+ (NH 4,, K, temp) housing material stainless steel , POM-C, glas electrodes weight (min.) 2.7 kg dimensions (diameter x length) 60 x 326 mm operating temperature C storage temperature C operating pressure mbar installation / mounting submersed or in Bypass (flow cell) process connection G 1 1/2 outside flowrate 0.01 m/s (min.) 3 m/s (max.) protection class IP 68 automatic cleaning media: compressed air permissible pressure: bar air volume: liter per cleaning cleaning duration: seconds per cleaning cleaning interval: minutes, depending on application delay: seconds conformity - EMC EN :1992 EN :1992 EN :1987 EN :1987 conformity - safety EN :2001 typical concentration ranges for this application NH 4 -N NO 3 -N K [] temperature [ C] part number min E-532-pro max min E-532-pro+NO 3 -N max min E-532-pro+ max

5 Messgeräte Sonstige Daten fluor::lyser II s::can plug & measure measuring principle: ISE (ionenselektive elektrodes) fluor::lyser II monitors fluoride and temperature cross sensitivities: OH- (at >8), Al3+, Ca2+, Fe3+, Si4+ (in typical drinking water cross sensitivities are not a problem) [multiparameter probe] long term stable, factory precalibrated automatic cleaning with compressed air easy and quick mounting and measurement directly in the media (InSitu) or in Bypass (monitoring station) operation via s::can terminals & s::can software ideal for drinking water minimal maintenance recommended accessories part number article name F-11-ammo carrier ammo::lyser F-44-ammo flow cell for ammo::lyser F-50-2 system-panel for s::can ISE probes and s::can sensors C-210-sensor 10 m extension cable for s::can oxi::lyser and ammo::lyser B-44 cleaning valve 5

6 technical specification measuring principle ISE measuring range application 0, mg/l automatic compensation instrument temperature precalibrated ex-works all parameters integration via con::lyte 1 con::lyte 2 con::lyte 4 con::nect con::stat power supply VDC power consumption (typical) 0.75 W interface connection to s::can sys plug, IP 68, RS485, 12 VDC terminals cable length 10 m cable type PU jacket 2x2x0.25 housing material stainless steel , POM-C, glas electrodes weight (min.) 2.7 kg dimensions (diameter x length) 60 x 326 mm operating temperature C storage temperature C installation / mounting submersed or in Bypass (flow cell) process connection G 1 1/2 outside range protection class IP 68 automatic cleaning media: compressed air permissible pressure: bar air volume: liter per cleaning cleaning duration: seconds per cleaning cleaning interval: minutes, depending on application delay: seconds drinking water typical concentration ranges for this application F temperature part number [ C] fluor_lyser_2 min E 542 max