Luckylight. 5mm Round With Flange Type. Purple LED. Technical Data Sheet. Part No.: 504UVC2E-Q5C

Transcription

1 5mm Round With Flange Type Purple LED Technical Data Sheet Part No.: 54UVC2E-Q5C Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 1 OF 7

2 Features: Popular T-1 3/4 diameter package. No IR emission. Ideal for heat sensitive materials. Instant on and instant off. Sharp spectrum. Compact light (free design). Power is adjustable by current (No Shutters Needed). Ability to operate in low temperature. Impact resistan. The product itself will remain within RoHS compliant Version. Applications: Photo catalyst excitation. Phosphor excitation. Sensor. QA equipment. Counterfeit Bill Detection. Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 2 OF 7

3 Package Dimension: 5 [.197] 5.85 [.23] R2.45 Polarity 5 [.197] 1 [.39] 8.65 [.341].6 [.24] 26.[1.24] Min..5 [.2] ANODE CATHODE 1 [.39] Min..5 [.2] 2.54 [.1] Part No. Chip Material Lens Color Source Color 54UVC2E-Q5C InGaN Water Clear Purple Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±.25mm (.1 ) unless otherwise noted. 3. Protruded resin under flange is 1.mm (.39 ) max. 4. Specifications are subject to change without notice. Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 3 OF 7

4 Absolute Maximum Ratings at Parameters Symbol Max. Unit Power Dissipation PD 1 mw Peak Forward Current (1/1 Duty Cycle,.1ms Pulse Width) IFP 1 ma Forward Current IF 25 ma Reverse Voltage VR 5 V Electrostatic Discharge (HBM) ESD 4 V Operating Temperature Range Topr -4 to +85 Storage Temperature Range Tstg -4 to +1 Lead Soldering Temperature [4mm (.157 ) FromBody] Tsld 26 for 5 Seconds Electrical Optical Characteristics at Parameters Symbol Min. Typ. Max. Unit Test Condition Luminous Intensity * IV mcd IF=2mA (Note 1) Viewing Angle * 2θ1/ Deg IF=2mA (Note 2) Peak Emission Wavelength λp nm IF=2mA Dominant Wavelength λd nm IF=2mA (Note 3) Spectral Line Half-Width λ nm IF=2mA Forward Voltage VF V IF=2mA Reverse Current IR µa VR=5V Notes: 1. Luminous Intensity Measurement allowance is ± 1%. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 4 OF 7

5 Typical Electrical / Optical Characteristics Curves (25 Ambient Temperature Unless Otherwise Noted) Spectrum Distribution Forward Current & Forward Voltage Relative Luminous Intensity (%) Relative Luminous Intensity (%) Luminous Intensity & Ambient Temperature Wavelength p (nm) Ambient Temperature Ta ( ) Forward Current IF (ma) Forward Voltage VF (V) Luminous Intensity & Forward Current Relative Luminous Intensity (%) f=1khz Duty=1/ Forward Current IF (ma) 4. Forward Current IF (ma) Forward Current Derating Curve Ambient Temperature Ta ( ) Radiation Diagram o 1 o 2 o 3 o 4 o 5 o 6 o 7 o 8 o 9 o Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 5 OF 7

6 Reliability Test Items And Conditions: The reliability of products shall be satisfied with items listed below: Confidence level: 9%. LTPD: 1%. 1) Test Items and Results: Standard Test Test Item Test Conditions Note Method Resistance to Soldering Heat Solder ability Thermal Shock Temperature Cycle Moisture Resistance Cycle High Temperature Storage Terminal Strength (Pull test) Terminal Strength (bending test) Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Tsld=26±5, 1sec 3mm from the base of the epoxy bulb Tsld=235±5, 5sec (using flux) Number of Damaged 1 time /1 1time over 95% /1 ~1 15sec, 15sec 1 cycles /1-4 ~25 ~1 ~25 3min, 5min, 3min, 5min 25 ~65 ~-1 9%RH 24hrs/1cycle 1 cycles /1 1 cycles /1 Ta=1 1hrs /1 Load 1N (1kgf) 1±1sec Load 5N (.5kgf) ~9 ~ bend 2 times No noticeable damage No noticeable damage /1 /1 Ta=6, RH=9% 1hrs /1 Ta=-4 1hrs /1, IF=3mA 1hrs /1 Ta=6, RH=9%, IF=3mA 5hrs /1 Ta=-3, IF=2mA 1hrs /1 2) Criteria for Judging the Damage: Item Symbol Test Conditions Criteria for Judgment Min Max Forward Voltage VF IF=2mA --- F.V.*) 1.1 Reverse Current IR VR=5V --- F.V.*) 2. Luminous Intensity IV IF=2mA F.V.*) *) F.V.: First Value. Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 6 OF 7

7 Please read the following notes before using the product: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 3 or less and 8%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 3 or less and 6%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 3. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 26 for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4. Soldering When soldering, for Lamp without stopper type and must be leave a minimum of 3mm clearance from the base of the lens to the soldering point. To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Temperature Soldering Time Soldering Iron 3 Max. 3sec.Max. (one time only) Pre-heat Pre-heat Time Solder Wave Soldering Time Wave Soldering 1 Max. 6 sec. Max. 26 Max. 5sec.Max. Note: Excessive soldering temperature and / or time might result in deformation of the LED lens or catastrophic failure of the LED. 5. Repairing RepairshouldnotbedoneaftertheLEDshavebeensoldered.Whenrepairingisunavoidable,a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 6. Caution in ESD Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices equipment and machinery must be properly grounded. Spec No.: B58 X335 Rev No.: V.3 Date: May./23/28 Page: 7 OF 7