Gas ejector for single-stage liquid ring vacuum pumps
|
|
- Gerard Riley
- 6 years ago
- Views:
Transcription
1 Gas ejector for single-stage liquid ring vacuum pumps GEV 5... GEV 800 Operating pressure: Suction volume flow: 8 to 80 mbar 5 to 050 CONSTRUCTION TYPE Sterling SIHI gas ejectors are simple and sturdy vacuum gas ejectors with following particular characteristics: Adaptable to different operating conditions by adequate material selection Simple installation into the suction line of liquid ring vacuum pumps Low noise service which is free of maintenance and deficient in vibration GEV 50 + LEM 50 NOTE APPLICATION Sterling SIHI gas ejectors extend the operating range of Sterling SIHI liquid ring vacuum pumps so that lower absolute pressures become possible (to 8 mbar). Field of application are e.g.: Chemistry and pharmacy for distilling and degassing The characteristics of the of the gas ejectors depend on essentially on the suction capacity of the liquid ring vacuum pump and therefore on the vapour pressure ant temperature of the service liquid used. To meet with the different conditions, we offer construction series. Type: A B Service liquid: water to 5 C water to 30 C Electric industry for impregnation and drying Suction pressure: mbar mbar Plastics industry for degassing etc. The gases which are to be handled may be vapour saturated or aggressive. Sterling SIHI gas ejectors are used wherever the vacuum attainable by a liquid ring vacuum pump is not sufficient and where danger of running in cavitation is immenent for the liquid ring vacuum pump. Even if the suction side of the ejector is closed, the liquid ring vacuum pump is protected against cavitation. POLLUTION CONTROLL: To reduce the exhaust blast the motive gas can be removed from the separator. The standard combinations described in this catalogue list are optimal in view of, power absorption and service charges. Other combinations of gas ejectors and liquid ring vacuum pumps can be applied. Details on request. VACUUM TECHNOLOGY GPV G E 05/99
2 Gas ejectors for two-stage liquid ring vacuum pumps GOV 3, GOV 3 GPV GPV 63 Operating pressure: Suction volume flow: 4 to 80 mbar 0 to 400 CONSTRUCTION TYPE Sterling SIHI gas ejectors are simple and sturdy vacuum gas ejectors with following particular characteristics: Adaptable to different operating conditions by adequate material selection Simple installation into the suction line of liquid ring vacuum pumps Low noise service which is free of maintenance and deficient in vibration NOTE The characteristics of the of the gas ejectors depend on essentially on the suction capacity of the liquid ring vacuum pump and therefore on the vapour pressure ant temperature of the service liquid used. To meet with the different conditions, we offer construction series. APPLICATION Sterling SIHI gas ejectors extend the operating range of liquid ring vacuum pumps so that lower absolute pressures become possible (to 8 mbar). Fields of application are e.g.: Chemistry and pharmacy for distilling and degassing Electric industry for impregnation and drying Plastics industry for degassing etc. The gases to be handled may be vapour saturated or aggressive. Sterling SIHI gas ejectors are used wherever the vacuum attainable by a liquid ring vacuum pump is not sufficient and where danger of running in cavitation is immenent for the liquid ring vacuum pump. Even if the suction side of the ejector is closed, the liquid ring vacuum pump is protected against cavitation. Service liquid: water up to 5 C water up to 30 C Suction pressure: mbar mbar Series: GOV 3,3 GOV 3, 3 GPV GPV In case of particularly low suction the gas ejector GPV 5 is available. Service liquid: water 5 C Suction pressure: 4... mbar POLLUTION CONTROLL: To reduce the exhaust blast the motive gas can be removed from the separator. The standard combinations described in this catalogue list are optimal in view of, power absorption and service charges. Other combinations of gas ejectors and liquid ring vacuum pumps can be applied. Details on request. VACUUM TECHNOLOGY GPV G E 07/00
3 Material design MATERIAL DESIGN Item COMPONENTS Casing Venturi tube holder * Insert ring Motive nozzle hard rubber Venturi tube In case of material design 88 the venturi tube holder is not in contact with the medium handled. * only in case of material design 88 Sectional drawing
4 Technical Data Suction pressure range 4 to mbar Service liquid temperature up to 5 C gas ejector + liquid ring vacuum pump pump speed rated power of the motor of the liquid ring vacuum pump pressure at a suction volume flow = zero make-up water requirements in m 3 /h KB difference in temperature C rpm kw mbar 5 GPV 5 + LPH ca. 0,95,55,7 FB Suction pressure range 8 to 40 mbar Service liquid temperature to 5 C gas ejector + liquid ring vacuum pump pump speed rated power of the motor of the liquid ring vacuum pump pressure at a suction volume flow = zero make-up water requirements in m 3 /h KB difference in temperature C rpm kw mbar 5 GOV 3 + LOH ,5 0,3 0, 0,34 GOV 3 + LOH , , 0,34 0,75 GPV 40 + LPH ,5 0,45 0,9 GPV 40 + LPH , ,35 0,6 0,95 GPV 50 + LPH , ,75,4,7 GPV 50 + LPH ,95,55 GPV 60 + LPH ,,7,6 GPV 60 + LPH ,5,,8 FB Suction pressure range 0 to 80 mbar Service liquid temperature to 30 C gas ejector + liquid ring vacuum pump pump speed rated power of the motor of the liquid ring vacuum pump pressure at a suction volume flow = zero make-up water requirements in m 3 /h KB difference in temperature C rpm kw mbar 0 5 GOV 3 + LOH ,5 7 0,08 0,3 0,34 GOV 3 + LOH , 0, 0,9 0,75 GPV 43 + LPH ,5 0,5 0,85 GPV 43 + LPH , 0,3 GPV LPH ,5 0,5 0,4 0,95 GPV 53 + LPH ,5 9 0,45 0,75 GPV 53 + LPH ,5 0,85,7 GPV LPH ,6 0,95 GPV 63 + LPH ,7,,6 GPV 63 + LPH ,5 0,8, FB = make-up liquid service KB = combined liquid service, service liquid 0 C, 5 C or C warmer than the make-up water The make-up water flows refer to the lowest indicated. In case of increasing these figures decrease. FB The values indicated are valid for compression of dry air of 0 C from to atmospheric pressure (03 mbar). Service liquid for the liquid ring vacuum pump also indicated is water to a temperature of 5 C resp. 30 C. The motive air for the gas ejector has a pressure of abt. 03 mbar. Motive and handling gases with physical characteristics which deviate from those of air, service water with other temperatures than those indicated, as well as other service liquids than water cause a change in suction capacity, which can be determined by Sterling SIHI on request. 3
5 Performance graph of the combinations Suction pressure range: 4 to mbar for service liquid temperatures to 5 C GPV 5 + LPH 5530 speed: 450 rpm mbar 000 Suction pressure range: 8 to 40 mbar for service liquid temperatures to 5 C GPV 60 + LPH 6537 GPV 60 +LPH 6530 GPV 50 + LPH 5530 GPV 50 + LPH 553 GPV 40 + LPH 4536 GPV 40 + LPH GOV 3 + LOH 5309 GOV 3 + LOH speed: 900 rpm speed: 450 rpm mbar 000 For the the tolerance is 0 %. 4
6 Performance graph of the combinations Suction pressure range: 0 to 80 mbar for service liquid temperatures up to 30 C GPV 63 + LPH 6537 GPV 63 + LPH 6530 GPV LPH 5530 GPV 53 + LPH 5536 GPV 53 + LPH 553 GPV 53 + LPH 553 GPV LPH 4536 GPV 43 + LPH 453 GOV 3 + LOH 5309 GOV 3 + LOH speed: 900 rpm speed: 450 rpm mbar 000 For the the tolerance is 0 %. 5
7 Dimension table N = gas-inlet, N = gas-outlet, TG = motive gas inlet series + N / N TG b e w weight in kg for material design size 8 88 GOV 3 DN 3 * G ¼ ,5 4 GOV 3 GPV 40 G ½ ,5 3 GPV 40 G ¾ GPV 43 DN GPV 43 G ½ ,5 3 GPV 433 GPV 50 G GPV 50 DN 3 * GPV 5 DN 50 GPV 53 GPV 53 G GPV 533 GPV GPV 60 DN 65 DN 5 ** GPV GPV 63 * Flange suitable for counterflange as per DIN 558 ** Flange suitable for counterflange as per DIN 56 Flange connections as per DIN 50 PN 0 DIN 558 PN 6 DIN 56 PN 0 DN k D d x number 8 x 4 8 x 4 8 x 4 4 x 4 x d s Example for ordering: G P V series size material design case sealing On delivery the point ( ) in the fourth place of the type code is replaced by a letter in the factory. Any changes in the interest of the technical development are reserved. Sterling SIHI GmbH Lindenstraße 70, D-554 Itzehoe, Germany, Telephone +49 (0) , Fax +49 (0)
8 Material design GEV 5 and GEV 50 GEV 90...GEV 50 GEV 50...GEV 45 GEV GEV 450 Item COMPONENTS 0S 4F 0R 0B 4B 0A 4B 0970 Motive nozzle.457 hard rubber Venturi tube Casing EP-resin glass-fibre reinforced Venturi tube holder not available Insert ring not available.457 not available.457 GEV GEV 800 GEV 9...GEV 6 Item COMPONENTS 0A 4B Item COMPONENTS 0A 4B 0970 Motive nozzle Motive nozzle Venturi tube 7.50 Venturi tube 095 Casing Casing Venturi tube holder.0038 In case of the material design 4B the venturi tube holder is not in contact with the medium handled. Sectional drawing GEV 5 + GEV 50 GEV 9... GEV 6 GEV GEV 800
9 Technical Data Suction pressure range 8 to 40 mbar type A service liquid temperature up to 5 C Suction pressure range 0 to 80 mbar type B service liquid temperature up to 30 C gas ejector + liquid ring-vacuum pump pumpspeed rated power of the motor of the liquid pressure at a suction volume flow = zero make-up water flow for differnce in temperature ring vacuum pump mbar mbar rpm kw type A type B C 5 C GEV 5 + LEM ,75 8 -* 0, 0,06 GEV 50 + LEM 50,5 0,9 0, GEV 9 + LEM/L 9 AZ/AB 900, ,35 0, GEV 6 + LEM/L 6 AZ/AB ,4 0,6 GEV 6 + LEM/L 6 AZ/AB ,65 0,39 GEV 90 + LEM/L 90, ,4 0, GEV 5 + LEM/L 5 3 0,47 0,6 GEV 50 + LEM/L ,49 0,8 GEV 50 + LEM/L ,5 8 0,6 0,34 GEV 35 + LEM 35 7,5 0,9 0,55 GEV 45 + LEM 45, 0,78 GEV LEH 350 7, ,0 0,53 GEV LEH 450,5 0,7 GEV LEH ,7,0 GEV LEH ,5 7,0, GEV LEH 900,4,5 GEV 00 + LEH ,3,7 GEV LEH ,75 3, GEV LEH ,0 3,3 The gas ejectors GEV 5 and GEV 50 only are available as type A. At a service water temperature of 30 C and suction volume flow zero a pressure of 7 mbar is reached. The make-up liquid flow ist indicated for combined operation. The service liquid is C resp. 5 C warmer than the make-up water. Data for make-up water operation, see operation instructions for liquid ring vacuum pumps. The values indicated for the are applicable for the compression of dry air of 0 C from to atmospheric pressure (03 mbar). As service liquid for the liquid ring vacuum pump is used water of 5 C resp. 30 C. The motive air for the gas ejector has a pressure of abt.. 03 mbar. Motive and pumping gases with physical properties differing from those of air, service water with temperatures different from those indicated, as well as service liquids other than water, cause a change of the suction capacity which can be determined by Sterling SIHI on request. 3
10 Performance graph of the combinations Suction pressure range: 8 to 40 mbar for service liquid temperatures up to 5 C GEV 45A+LEM GEV 35A+LEM 35 GEV 50A+LEM/L 50 GEV 50A+LEM/L 50 GEV 5A+LEM/L 5 GEV 90A+LEM/L 9 GEV 50A+LEM 50 GEV 5A+LEM 5 4 speed: 800 rpm speed: 450 rpm mbar GEV 6A+LEM 6 GEV 6A+LEM GEV 9A+LEM 9 speed: 900 rpm speed: 460 rpm mbar 000 If a combination gas ejector - liquid ring vacuum pump is applied in the range from 40 mbar to 03 mbar, the motive gas flow can be shut off. Then the of the combination increases by abt. 5 %. For the the tolerance is 0 %. 4
11 Performance graph of the combinations Suction pressure range: 8 to 40 mbar for service liquid temperatures up to 5 C 00 GEV 800A+LEH GEV 500A+LEH GEV 00A+LEH 00 3 GEV 900A+LEH 900 GEV 800A+LEH 800 GEV 600A+LEH speed: 450 rpm speed: 460 rpm 3 speed: 975 rpm GEV 450A+LEH 450 GEV 350A+ LEH mbar000 If a combination gas ejector - liquid ring vacuum pump is applied in the range from 40 mbar to 03 mbar, the motive gas flow can be shut off. Then the of the combination increases by abt. 5 %. For the the tolerance is 0 %. 5
12 Performance graph of the combinations Suction pressure range: 0 to 80 mbar for service liquid temperatures up to 30 C GEV 45B+LEM GEV 35A+LEM 35 GEV 50B+LEM/L 50 GEV 50B+LEM/L GEV 5B+LEM/L 5 GEV 90B+LEM/L 9 GEV 50B+LEM 50 GEV 5B+LEM 5 4 speed: 800 rpm speed: 450 rpm mbar GEV 6B+LEM GEV 6B+LEM 6 GEV 9B+LEM 9 speed: 900 rpm speed: 460 rpm mbar 000 If a combination gas ejector - liquid ring vacuum pump is applied in the range from 80 mbar to 03 mbar, the motive gas flow can be shut off. Then the of the combination increases by abt. 5 %. For the the tolerance is 0 %. 6
13 Performance graph of the combinations Suction pressure range: 0 to 80 mbar for service liquid temperatures up to 30 C GEV 800B+LEH GEV 500B+LEH GEV 00B+LEH GEV 900B+LEH GEV 800B+LEH 800 GEV 600B+LEH 600 GEV 450B+LEH GEV 350B+ LEH 350 speed: 450 rpm speed: 460 rpm 3 speed: 975 rpm mbar 000 If a combination gas ejector - liquid ring vacuum pump is applied in the range from 80 mbar to 03 mbar, the motive gas flow can be shut off. Then the of the combination increases by abt. 5 %. For the the tolerance is 0 %. 7
14 Dimension table GEV 5 + GEV 50 GEV 9 to GEV 6 GEV 90 to GEV 450 GEV 600 to GEV 800 Flange connections N = gas-inlet, N = gas-outlet, TG = motive gas inlet 8 series + type weight in kg for material design size N N b d e w SW 0R 0 0B 0 4B 0 0A 0 0S 0 4F 0 GEV 5 A G G 5 G / , GEV 50 A GEV 9 A, B G /4 G / ,8 3,6 GEV 6 A, B 33,5 G / , 3,9 GEV 6 A, B G / G / ,0 4,7 GEV 90 A, B 84 7,5 8,5 GEV 5 A B ,5 8,5 - GEV 50 A B 39 GEV 50 A, B ,5 GEV 35 A G / B GEV 45 A ,5 9,5 B GEV 350 A,B 5 5 GEV 450 A B 576 6,5 GEV 600 A, B GEV 800 A, B * GEV 900 A, B 866 GEV 00 A, B GEV 500 A B ** GEV 800 A B * Flange suitable for counter-flange as per DIN 56 ** Flange suitable for counter-flange as per DIN 558 flange connections as per DIN 50 PN 0 DIN 56 PN 0 DIN 558 PN 6 DN k D d x number 8 x 4 8 x 4 8 x 4 8 x 8 8 x 8 4 x 4 x d s Example for ordering: G E V A 9 A 0A 0 series size type material design Any changes in the interest of the technical development are reserved. Sterling SIHI GmbH Lindenstraße 70, D-554 Itzehoe, Germany, Telephone +49 (0) 48 / 7 7-0, Fax +49 (0) 48 /
Gas ejectors for two-stage liquid ring vacuum pumps
Gas ejectors for two-stage liquid ring vacuum pumps GOV 3, GOV 3 GPV 0... GPV 63 Operating pressure: Suction volume flow: to 80 mbar 0 to 00 m³/h CONSTRUCTION TYPE Sterling SIHI gas ejectors are simple
More informationROOTS VACUUM PUMPS RSV SERIES
ROOTS VACUUM PUMPS RSV SERIES ROOTS VACUUM PUMPS RSV SERIES Roots Vacuum Pumps 300-600 m 3 /h Series (175-350 cfm) Pumps with a hermetic canned motor, with by-pass. 1000-2000 m 3 /h Series (600-1200 cfm)
More informationThe Filterautomat. Our Filter Systems Protect. The New Definition of Purity for Your Medium. flow rate 5 m 3 /h to 4,000 m 3 /h. filter fineness 5 µm
GB Filterautomat The New Definition of Purity for Your Medium Our Filter Systems Protect The Filterautomat Cooling Water River Water Plate Heat Exchangers Spray Nozzles Sea Water Sinter and Scale Separation
More informationSteam balance optimisation strategies
Steam balance optimisation strategies Publicado en Chemical Engineering, Noviembre 2002 Background Optimising a steam balance in a plant with several steam mains pressures is not always a simple intuitive
More information20/06/2011 Seminar on Geothermal Exploitation Santiago de Chile
Contents Power Plants Steam Power plants Binary Power plants Geothermal Power Plants Single flash systems Binary systems 1 Equipment Well head Gathering piping system Steam separators and moisture separators
More informationClose Coupled Sump Pumps Type ETLB
Close Coupled Sump Pumps Type ETLB»dry running safe«technical data Flow rate Q up to 104 m 3 /h Head H up to 36 m Submersion depth up to 775 (795) mm Suction extension up to 1500 mm Materials limits of
More informationChapter 3.7: Cooling Towers
Part-I: Objective type questions and answers Chapter 3.7: Cooling Towers 1. The type of cooling towers with maximum heat transfer between air to water is. a) Natural draft b) Mechanical draft c) Both a
More informationLV Image Frankreich :05 Uhr Seite SOGEVAC. Rough Vacuum by Leybold
07635-05 LV Image Frankreich 04.11.2005 12:05 Uhr Seite 1 00.165.01 SOGEVAC Rough Vacuum by Leybold 07635-05 LV Image Frankreich 04.11.2005 12:05 Uhr Seite 2 Leybold Vacuum Worldwide With about 1300 people
More informationProcess Inline Filter, Change-Over
Process Inline Filter, Change-Over -503-130x -520x 1. TECHNICAL SPECIFICATIONS 1.1 GENERAL Inline filters, types PRFL and duplex inline filters are designed for process engineering and chemical plants.
More informationHTP. HTP070 Purifier for Dielectric Fluids. PIH HTP070b
PIH HTP070b The HTP070 purifier permits treatment of the oil in a power transformer, while on-line and on-load. Application Areas The PALL HTP070 oil purifier removes water, solid particles, air and other
More informationData Sheet. Measuring System trikon Vortex Flow Meter EDZ 420 in Microprocessor Technology. Vortex meter trikon EDZ 420.
Data Sheet Measuring System trikon Vortex Flow Meter EDZ 420 in Microprocessor Technology Application Metering and recording of volume or mass flow of gases, liquids and steam. Vortex meter trikon EDZ
More informationIn-line Twin Pump. Type Series Booklet. Omega DSL
In-line Twin Pump Type Series Booklet Legal information/copyright Type Series Booklet All rights reserved. The contents provided herein must neither be distributed, copied, reproduced, edited or processed
More informationAB-1020 EP Dust Free Vacuum Blast Machine
AB-1020 EP Dust Free Vacuum Blast Machine This compact electric-pneumatic driven injection vacuum blasting machine with an average blasting pattern of 16 mm width, is excellent to apply for blast cleaning
More informationDCV Wafer check valves
V Wafer check valves V wafer check valves to prevent reverse flow... The Spirax Sarco range of V wafer check valves provides an effective minimal maintenance free solution for the prevention of reverse
More informationSAPAG. A full range of API 526 flanged safety relief valves for process applications, gas, steam and liquid. Safety Relief Valve Series 8100/8200
SAPAG A full range of API 526 flanged safety relief valves for process applications, gas, steam and liquid. Features Full compliance to API RP 520 and standards 526, 527. Certified ASME Section VIII on
More informationARI-STEVI 440 / 441 (DN15-250) Control valve - straight through With pneumatic and electric actuators
ARI-STEVI 4 / 441 (DN15-0) Control valve - straight through With pneumatic and electric actuators ARI-STEVI 4 / 441 Pneumatic actuator ARI-DP 32-34 Tri Reversible pneumatic actuator Actuator with rolling
More informationExperience In Motion. SIHI Side Channel Pumps High Head at Low Flow
Experience In Motion SIHI Side Channel Pumps High Head at Low Flow Pump Supplier to the World 2 Flowserve is the driving force in the global industrial pump marketplace. No other pump company in the world
More informationERT 318/4 UNIT OPERATIONS SEMESTER 1 (2013/2014)
ERT 318/4 UNIT OPERATIONS SEMESTER 1 (2013/2014) WATER COOLING TOWER School of Bioprocess Engineering University Malaysia Perlis EXPERIMENT Water Cooling Tower 1.0 OBJECTIVES 1.1 To determine energy and
More informationx act i Precision Pressure Transmitter for Food Industry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to IEC 60770: 0.
Precision Pressure Transmitter for Food ndustry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to EC 60770: 0. % FSO Nominal pressure from 0... 400 mbar up to 0... 40 bar Output
More informationAutogas Series. Regenerative Turbine Coro-Flo Pumps. For LPG High Differential Pressure Applications
Autogas Series Regenerative Turbine Coro-Flo Pumps For LPG High Differential Pressure Applications A Tradition of Excellence Corken, Inc. is recognized as a world leader in the manufacture of LPG pumps
More informationGeothermal Power Plant
Geothermal Power Plant The Tokyo Electric Power Co., Inc., Japan Hachijo-jima Geothermal Power Plant 3,300kW 0A3-E-009 Outline All equipment and system except for the civil work and geothermal wells were
More informationFloat Flow Meters series NF
Float Flow Meters series NF - Quality design - High corrosion resistance - Reliable measurement principle - Low weight and small dimensions Doc. no.: 22, en_cat_nf, 8/2015 Usage Flowmeters type NF are
More information- CONSTRUCTIONS 300 SECTIONAL VIEW 300 SECTIONAL TABLE 301 QUANTITY FOR MODEL 302 MECHANICAL SEAL 303 BEARINGS 304
CONTENTS Page - SPECIFICATIONS 200 PERFORMANCE RANGE and SELECTION CHART 201 TYPE KEY and CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 40 203 PERFORMANCE CURVE 80 204 - CONSTRUCTIONS 300 SECTIONAL VIEW 300
More informationT U R B O B L O W E R S
A e r z e n T U R B O B L O W E R S New Aerzen Turbo Blower Units Volume Flow Intakes from 1,000 m³/h to 13,200 m³/h A E R Z E N E R M A S C H I N E N F A B R I K G M B H GODREJ & Boyce Mfg. Co. Ltd. -
More informationProduct Range Non-Metallic Pumps
Product Range Non-Metallic Pumps In / PE-UHMW / / PFA Types Horizontal with Magnetic Drive Horizontal with Mechanical Seal Vertical with Labyrinth Seal Vertical with Mechanical Seal Cantilever Pump Your
More informationVibration Control SCHWINGMETALL. The Original Rubber-To-Metal Bonding from ContiTech
Vibration Control SCHWINGMETALL The Original Rubber-To-Metal Bonding from ContiTech ContiTech Vibration Control Innovator and Development Partner ContiTech is an innovator and development partner for vibration-damping
More informationx act i Precision Pressure Transmitter for Food Industry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to IEC 60770: 0.
Precision Pressure Transmitter for Food ndustry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to EC 60770: 0. % FSO Nominal pressure from 0... 400 mbar up to 0... 40 bar Output
More informationPioneering ALD experience since The ALD Powerhouse PRODUCT CATALOGUE FOR SUNALE P-SERIES ALD SYSTEMS
Pioneering ALD experience since 1974 The ALD Powerhouse PRODUCT CATALOGUE FOR SUNALE P-SERIES ALD SYSTEMS SUNALE P-SERIES ALD SYSTEMS PRODUCT CATALOGUE Description SUNALE P-series ALD system SUNALE P-series
More informationSHORT FIBRE RIGID INSULATION AND SOFT FELT
TECHNICAL GUIDE SHORT FIBRE RIGID INSULATION AND SOFT FELT SHORT FIBRE AND SOFT FELT FOR THERMAL INSULATION FOR FURNACE WORKING UNDER VACUUM OR INERT GAS + THE RIGHT ENGINEERED SOLUTION ADAPTED TO YOUR
More informationCROSBY H-SERIES DIRECT SPRING SAFETY VALVES
DIRECT SPRING SAFETY VALVES Direct spring safety valves that provide comprehensive overpressure protection for ASME Boiler and Pressure Vessel Code Section I, and Section VIII steam safety applications
More informationExperience In Motion. SIHI Gas separation by using membranes
Experience In Motion SIHI Gas separation by using membranes Pump Supplier to the World 2 Flowserve is the driving force in the global industrial pump marketplace. No other pump company in the world has
More informationComparing Evaporative Technologies for the Recycling of Produced Waters
Comparing Evaporative Technologies for the Recycling of Produced Waters Relatively recent advance refinements of evaporative technologies have enabled a cost effective solution for a variety of wastewater
More informationSHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM IV (ME-41, 42,43 & 44)] QUIZ TEST-1 (Session: )
QUIZ TEST-1 Q.1. In a stage of an impulse turbine provided with a single row wheel, the mean diameter of the blade ring is 80cm and the speed of the rotation is 3000rpm. The steam issues from the nozzle
More informationTHE MICROFLOW SENSOR MICROFLOW SENSOR WITH A WIDE RANGE OF APPLICATIONS THANKS TO THE AVAILABILITY OF DIFFERENT CONNECTION TYPES
THE MICROFLOW SENSOR MICROFLOW SENSOR WITH A WIDE RANGE OF APPLICATIONS THANKS TO THE AVAILABILITY OF DIFFERENT CONNECTION TYPES The manufacturer guarantees only English text. Available on our web site:
More informationRAMPF Polymer Solutions GmbH & Co. KG Thilo Heuft / High performance reactive resins for component protection in extreme environments
RAMPF Polymer Solutions GmbH & Co. KG Thilo Heuft / 05.11.2015 High performance reactive resins for component protection in extreme environments The RAMPF Group RAMPF stands for Engineering and Chemical
More informationTECHNICAL HANDBOOK. ASME B73.1 Process Pump. Wilfley Sealing Technology. No Flush Water Required
TECHNICAL HANDBOOK ASME B3. Process Pump A Wilfley Sealing Technology No Flush Water Required WILFLEY SEALING TECHNOLOGY Wilfley invented the Dynamic Expeller Seal almost a century ago and has continued
More informationINDIAN REGISTER OF SHIPPING CLASSIFICATION NOTES. Type Approval of Mechanical Joints used in Piping
INDIAN REGISTER OF SHIPPING CLASSIFICATION NOTES Type Approval of Mechanical Joints used in Piping January 2017 Page 2 of 16 Changes in JANUARY 2017 Version Type Approval of Mechanical Joints used in Piping
More informationWILLBRANDT PTFE Expansion Joint Type 80
WILLBRANDT PTFE Expansion Joint Type 0 00 Type 0 is a 3 or corrugated PTFE expansion joint that is hotformed under pressure from extruded PTFE tubing. The fibers are executed without interruption. It is
More informationThermocouples. Operating and Maintenance Manual English. Thermocouples
Thermocouples Operating and Maintenance Manual English Seite 1 / 8 Operating and Maintenance Manual Thermocouples Table of Contents 1 General Information 3 2 Functionality 4 2.1 Thermo Lines and Compensating
More information0.01 Micron Membrane Filters
Balston Natural Gas Filters Specialty Gas Filtration Analytical Gas Filtration Process Gas Filtration Critical Blow Off Applications 0.01 Micron Membrane Filters Filtration to 0.01 micron No particle shedding
More informationROWA-HP. High-Pressure Centrifugal Pump
ROWA-HP High-Pressure Centrifugal Pump Fields of Application Handling of clean to slightly contaminated corrosive liquids up to discharge pressures of 120 bar Design Horizontal, radial split, ring section
More informationInsulation in decks and bulkheads PYROLIQ sealing compound system
Insulation in decks and bulkheads PYROLIQ sealing compound system PYROLIQ casting compound In industry, ship construction and offshore areas, very high requirements are placed on cable and pipe penetrations
More informationPSG, TSG, SGS, SR Corrosion-resistant PFA and PTFE lining Indication of flow even at very low flow rates Optionally with integrated check valve
Richter and -Way Sight Glasses PSG, TSG, SGS, SR Corrosion-resistant PFA and PTFE lining Indication of flow even at very low flow rates Optionally with integrated chec valve Richter and -way sight glasses
More informationCompressed Air Systems. Compressed Air Filters. Balston Microfiber Filter Assemblies. Product Features
Compressed Coalescing Balston Microfiber Filter Assemblies Balston Coalescing Compressed protect your equipment and delicate instruments from the dirt, water, and oil usually found in compressed air. Balston
More informationTechnical Information No. 4 page 1
Technical Information No. 4 page 1 Temperature rise on the catalyst as a function of the hydrocarbon concentration of the exhaust gas The combustion of the hydrocarbons on the catalyst takes place with
More informationPOLYFLURON -E PTFE and POLYFLURON -P PTFE. The Right Column and Vessel Lining to Meet any Need. Process Technology. Broad Base. Best Solutions.
POLYFLURON -E PTFE and POLYFLURON -P PTFE The Right Column and Vessel Lining to Meet any Need Process Technology Broad Base. Best Solutions. SGL Group The Carbon Company SGL Group The Carbon Company is
More informationPerformance Analysis of Surface Condenser under Various Operating Parameters
Performance Analysis of Surface Condenser under Various Operating Parameters Ajeet Singh Sikarwar 1, Devendra Dandotiya 2, Surendra Kumar Agrawal 3 1 M.Tech. Student (Thermal System & Design) SRCEM, MORENA
More informationReturn Line Filter RFM
Return Line Filter RFM Flow rates up to 85 l/min Pressure range up to 1 bar Material: Aluminium/Steel/Synthetic material Return line filters type RFM are designed to be mounted on tank tops to filter out
More informationECLIPSE. NSF/ANSI 61* *Non-metallic Only EXTERNAL GEAR PUMP ENGINEERED PRODUCTS. Flow: up to 33 gpm (125 lpm)
ECLIPSE EXTERNAL GEAR PUMP Flow: up to 33 gpm (125 lpm) Differential Pressure: up to 15 psi (1.3 bar) Working Pressure: up to 3 psi (2.7 bar) Temperature: from -4 to 45 F (-4 to 232 C) Viscosity: up to
More informationTutorial letter 101/0/2016
Tutorial letter 101/0/2016 Hydraulic Machines III (Theory) FMA3602 Year Module Department of Mechanical and Industrial Engineering IMPORTANT INFORMATION: This tutorial letter contains important information
More informationMechatronic pressure measurement. Applications. Special features. Description
Mechatronic pressure measurement Diaphragm pressure gauge with switch contacts Model 432.56, high overload safety up to 100 bar Model 432.36, safety version, high overload safety up to 400 bar WIKA data
More informationE 094 E 103 E 143 Tank top mounting Connection up to G1 Nominal flow rate up to 135 l/min
Return Filters E 9 E E Tank top mounting Connection up to G Nominal flow rate up to l/min Description Application In the return line circuits of hydraulic systems. Performance features Protection against
More informationRichter Bellows-sealed Globe Control Valves
Richter Bellows-sealed Globe Control Valves RSS NEW: Size DN 50/6 Corrosion-resistant PFA lining ISO/DIN and ANSI/ISA face-to-face Heavy-duty bellows Special designs for chlorine and high-purity media
More informationFlooded Type Water-Cooled Chillers. R134a
Flooded Type WaterCooled Chillers The HighEfficiency WaterCooled Flooded Chillers The New WaterCooled Flooded chiller with improved efficiency and functionality by incorporating several advanced technology
More informationAN ALTERNATIVE TO VACUUM ENHANCED MULTI-PHASE EXTRACTION. Allan Shea, P.Eng.
AN ALTERNATIVE TO VACUUM ENHANCED MULTI-PHASE EXTRACTION Allan Shea, P.Eng. October 2003 Allan Shea BACKGROUND Experience has been mainly with: Above ground portion of mechanical remediation systems At
More informationSYMPOSIUM ON INDUSTRIAL APPLICATIONS OF GAS TURBINES
20TH SYMPOSIUM ON INDUSTRIAL APPLICATIONS OF GAS TURBINES Inlet Fogging and Overspray Impact on Gas Turbine Life and Performance by Klaus Brun / Southwest Research Institute Rainer Kurz / Solar Turbines
More information60Hz. Route range ZMR. mechanical sealed TMR. magnetical driven. centrifugal pumps in thermoplastic materials
6Hz Route range ZMR mechanical sealed TMR magnetical driven centrifugal pumps in thermoplastic materials 2 Route TMR - ZMR In this catalog Argal proposes the range of ROUTE pumps, inclusive of magnetical
More informationRIELLO 40 N SERIES. One Stage Heavy Oil Burners FIRING RATES HEAVY OIL. N kw N kw
One Stage Heavy Oil Burners RIELLO 40 N SERIES The Riello 40 N series of one stage heavy oil burners, is a complete range of products developed to respond to any request for the use of heavy oil in heating
More informationEFFECTS OF SHEAR AND CAVITATION ON PARTICLE AGGLOMERATION DURING HANDLING OF CMP SLURRIES CONTAINING SILICA, ALUMINA, AND CERIA PARTICLES
EFFECTS OF SHEAR AND CAVITATION ON PARTICLE AGGLOMERATION DURING HANDLING OF CMP SLURRIES CONTAINING SILICA, ALUMINA, AND CERIA PARTICLES Mark R. Litchy and Donald C. Grant CT Associates, Inc. Reto Schoeb
More informationSpecial Electrically Resistant Heated Furnaces
Special Electrically Resistant Heated Furnaces Drying of Ceramic Components Autor: Roland Waitz, Malte Möller Many ceramic masses are fabricated in plastic or liquid condition by addition of water. In
More informationFor highest levels of purity
For highest levels of purity Gas purification systems www.airliquide.de Individual gas purification... versatile, quick and clean Proven technology For several decades, Air Liquide has been offering you
More informationPrinting Version: for optimal viewing set the print to A3 and print two pages of the catalogue (including this one) on each sheet.
Printing Version: for optimal viewing set the print to A3 and print two pages of the catalogue (including this one) on each sheet. CUSTOM-MADE WATERWORKS VALVES SINCE 1967 Table of Contents The company
More informationTuchenhagen. Product Recovery Systems
Tuchenhagen Product Recovery Systems Tuchenhagen Product Recovery Systems Structure Advantages using Product Recovery Systems Preconditions for pigging Features of the Product Recovery Systems Sizes Range
More informationGLAUNACH THE SILENCER HANDBOOK INSULATION SUPPLEMENTARY ACOUSTIC SHIELDING OF SILENCERS, PIPES & CO GLAUNACH GMBH ALL RIGHTS RESERVED -
GLAUNACH THE SILENCER HANDBOOK INSULATION SUPPLEMENTARY ACOUSTIC SHIELDING OF SILENCERS, PIPES & CO GLAUNACH GMBH 2010 - ALL RIGHTS RESERVED - Part VIII page 2 of 9 There are two main motivations for adding
More informationSECTION MOTORS AND PUMPS FOR PLUMBING SYSTEMS
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including the General and Supplementary Conditions and Specification Sections, apply to this Section. B. Related
More informationXMP i. Precision Pressure Transmitter for the Process Industry with HART -Communication. Stainless Steel Sensor
Precision Pressure Transmitter for the Process Industry with HART -Communication Stainless Steel Sensor accuracy according to IEC 0770: 0. % FSO Nominal pressure from 0... 00 mbar up to 0... 00 bar Output
More information- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL 302 MECHANICAL SEAL and BEARINGS 303
CONTENTS Page - SPECIFICATIONS 200 PERFORMANCE RANGE and SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 40 203 PERFORMANCE CURVE 80 204 - CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING
More informationThe IMC / MTI - Process
PRACTICAL TIPS The IMC / MTI - Process next generation vacuum infusion - The manual attached to the animation - In-Mould Coating + Membrane wrapped suction line MTI -hose = Cost savings coupled with high
More informationCOOLING TOWER DESIGN FOR CENTRAL GENERATORS OF CUET, BANGLADESH. Mohammad Sharif Khan, Golam Mainuddin, Abu Sadat Mohammad Sayem, Nadeem Nafis
Proceedings of the 4 th BSME-ASME International Conference on Thermal Engineering 7-9 December, 008, Dhaka, Bangladesh COOLING TOWER DESIGN FOR CENTRAL GENERATORS OF CUET, BANGLADESH. Mohammad Sharif Khan,
More informationSeries description Wilo-Drain STS 40
Series description Wilo-Drain STS 40 Series description Wilo-Drain STS 40 Subject to change 09/2008 WILO SE Wilo Catalogue C2 - - Sewage pumps from DN 32 to DN 800 Materials Pump housing: EN-GJL-250 Pedestal:
More informationThe Liquiflo POLY-GUARD TM
A Revolutionary Innovation in Chemical Pump Technology... The Liquiflo POLY-GUARD Polymer-Lined Stainless Steel Gear Pump...The Ultimate Solution for Pumping Corrosive Chemicals Combines the chemical resistance
More informationFLOWRATE MEASURE PROBE DEBIX
IX serie - For pipes: ND 15 up to ND 3000 - Very low pressure loss - Flow = (f) P - For liquids, gazs and steams - Permanent accuracy ± 1% - Excellent repeatability: 0.1 % - Proof against impurities -
More informationAgilent IDP-3 Dry Scroll Pump For the Agilent 5977, 5975, and 5973 Series GC/MSD CLEAN. QUIET. RELIABLE. OIL FREE.
Agilent IDP-3 Dry Scroll Pump For the Agilent 5977, 5975, and 5973 Series GC/MSD CLEAN. QUIET. RELIABLE. OIL FREE. AGILENT IDP-3 DRY SCROLL PUMP LOUD NOISE, OIL LEAKS, AND PUMP BREAKDOWNS DON T HAVE TO
More informationXMP i. Precision Pressure Transmitter for the Process Industry with HART -Communication. Stainless Steel Sensor
Precision Pressure Transmitter for the Process Industry with HART -Communication Stainless Steel Sensor accuracy according to IEC 0770: 0. % FSO Nominal pressure from 0... 400 mbar up to 0... 00 bar Output
More informationJohnson. We now offer a real step forward in reliability with our newly designed riser pipes.
RISER PIPES Johnson enjoys today an enviable reputation with drilling and water industry professionals as the exclusive designer and manufacturer of wire-wrapped screens. In addition to our skills and
More informationChapter 5 1. Hydraulic Pumps (pp , Gorla & Khan; Wiki)
Chapter 5 1. Hydraulic Pumps (pp. 47 90, Gorla & Khan; Wiki) 1. Two Basic Categories of Pumps Positive Displacement (PD) Pumps A positive displacement pump causes a fluid to move by trapping a fixed amount
More informationPETREX -CNT. Pipe systems for petrol stations Technical details
PETREX - Pipe systems for petrol stations Technical details Contents 1.0 1.0 Contents 1.10 1.100 System description System description PETREX - 1.11 1.11.01 Product overview Piping, connections, fittings
More informationELECTROTECHNOLOGIES FOR ENERGY END-USES: APPLICATION OF MVR TO FOOD INDUSTRIES
ELECTROTECHNOLOGIES FOR ENERGY END-USES: APPLICATION OF MVR TO FOOD INDUSTRIES W. Grattieri, C. Medich, R. Vanzan CESI S.p.A. Within the scope of the demonstration projects of efficient electrotechnologies
More informationSOLAR MULTI-EFFECT DESALINATION SYSTEM
OPEN TENDER TECHNICAL SPECIFICATION FOR THE PROJECT SOLAR MULTI-EFFECT DESALINATION SYSTEM SPONSORED BY MINISTRY OF EARTH SCIENCES, GOVERNMENT OF INDIA, NEW DELHI INDEX S. NO DESCRIPTION PAGE NO. I PROJECT
More informationMANUFACTURING PROCESSES PREPREGS
PREPREGS Prepregging The reinforcement (carbon, fiberglass or aramid fiber or cloth) is saturated by dipping through the liquid resin. In an alternate method called a Hot Melt Process the resin is impregnated
More informationjung-process-systems.de Hygienic gentle economical
Hygienic gentle economical About us More than 40 years experience in fabrication and service for the food and beverage industry Premium in house machining and testing facilities for stainless steel or
More informationDISCOCHECK Dual-Plate Check Valves BB Short overall length according to DIN EN 558-1, table 11, series 16 (=^ DIN 3202, part 3, series K3)
pplication and Type PN pplication for liquids, gases and vapours Ø D 80 BB EN BB SME PN Class 150 suitable for heating, air-conditioning, water supply and cooling installations,for applications where minimum
More informationREPORT NO. 878 APPENDIX B. Sample Supply, Preparation and Homogeneity Testing
REPORT NO. 878 APPENDIX B Sample Supply, Preparation and Homogeneity Testing Sample Supply B1.1 Sample Preparation and Homogeneity Testing B1.2 - B1.4 B1.1 Sample Supply July 2013 to June 2014 Petrol Samples
More informationEBS Filters. The largest automatic self-cleaning filter for fine filtration micron. 30 psi (2 bar) less than 1% of the total flow
EBS Filters The largest automatic self-cleaning filter for fine filtration flowrates filtration degrees water for cleaning minimum operating pressure up to 32000 gpm (7200 m 3 /h) 800-10 micron less than
More informationAtlas Copco. ZM Oil-free multistage centrifugal pressure and vacuum blowers
Atlas Copco ZM Oil-free multistage centrifugal pressure and vacuum blowers 100-40,000 cfm / 2-24 psi / 5-3,600 hp 3-1160 m 3 /m / 100-1700 mbar / 4-2600 kw A ZM for every application Atlas Copco s ZM oil-free
More informationPressure transducers DMU 02 Vario (flush)
Process engineering (flush) Ideal for hygienic processes Connection technology with numerous versions Extremely resistant to shock, pulsation and vibration Best dynamic pressure resistance at high load
More informationwww.flexyvacuumcups.com Vacuum Cups Catalog 2016-2017 About Flexy Vacuum Cups About Flexy Vacuum Cups About Flexy Vacuum Cups From my long experience buying vacuum cups, I know customers buying branded
More informationKEYSTONE SWING TYPE WAFER CHECK VALVE FIGURE 86
High capacity, spring loaded swing type wafer check valve FEATURES Lightweight, wafer type check valve with face-to-face dimensions according ISO 5752, table 5 long High flow capacity featuring a special
More informationAutogas Series. Regenerative Turbine Coro-Flo Pumps For High Differential Pressure Applications Using LPG and Other Liquefied Gases.
Autogas Series Regenerative Turbine Coro-Flo Pumps For High Differential Pressure Applications Using LPG and Other Liquefied Gases motralec 4 rue Lavoisier. ZA Lavoisier. 95223 HERBLAY CEDEX Tel. : 01.39.97.65.10
More informationMagnetically Coupled Submerged Cryogenic Pumps and Expanders for Ammonia Applications
Paper 4d Magnetically Coupled Submerged Cryogenic Pumps and Expanders for Ammonia Applications Liquefied Ammonia, or Liquid NH3, is (like LNG or liquefied natural gas) a cryogenic fluid and production
More informationUni-Seals Product Catalog
Uni-Seals Product Catalog www.uni-seals.com 0 Index PTFE Sheet/Rod/Tube GS4000 Pure PTFE sheet.. 2 GS4010 PTFE molded sheet 2 GS4020 PTFE skived sheet.. 2 GS4100 Expanded PTFE sheet.. 3 RO4000 PTFE rod.
More informationCOMBINATION AIR VALVE
MINING DIVISION COMBINATION AIR VALVE FOR HIGH FLOW D-6NS SERIES DESCRIPTION The D-6NS Series Combination Air Valve has the features of both an air release valve and an air & vacuum valve. The air release
More informationELECTRICITY OUTPUT THERMAL OUTPUT ELECTRIC EFFICIENCY THERMAL EFFICIENCY TOTAL EFFICIENCY
CHP Technical Data Sheet for T200 Natural Gas Indoor Canopy Cento Series Standard Features High performance electrical efficiency Fully modulating output 3 packages Open frame, Indoor Canopy, Outdoor Container
More informationStraight running slat-band chains made of steel and stainless steel
LEAD BY IDEAS Straight running slat-band chains made of steel and stainless steel Type 812/815, dimensions, mass SPROCKET ISO N Plate S 815 - K 225 S 815 - K 263 S 815 - K 325 S 815 - K 400 S 815 - K 450
More informationDUBAL Energy Optimization Absorption Chiller Pilot Project
DUBAL Energy Optimization Absorption Chiller Pilot Project Global Sustainable Cities Network - 2014 23 January 2014 Tariq Alzarooni Manager: Asset Management: Power and Desalination Innovation in energy-conservation
More informationForced Draft Decarbonators. Degasification
Forced Draft Decarbonators Degasification Forced Draft Decarbonator When do you need it? What is it? How does it work? In Ion Exchange Demineralizer Systems, Forced Draft Decarbonators are located between
More informationPCM DELASCO. Peristaltic pumps Series DSC 65, 80, 100
17 rue Ernest Laval - BP 35-92173 Vanves Cedex France Tel (33) 01 41 08 15 15 - Telex 634 129 F - Fax (33) 01 41 08 15 00 Internet: pcmpompes.com Email: pcm@pcmpompes.com PCM DELASCO Peristaltic pumps
More informationCHAPTER 6 : GAS SAMPLING SYSTEMS
CHAPTER 6 : GAS SAMPLING SYSTEMS 1 Scope : 1.1 This Chapter describes two types of gas sampling systems in paragraphs 2.1 and 2.2 meeting the requirements specified in para 4.2 of Chapter 3 of this Part.
More information