SECTION 2.0 REFERENCES

Transcription

1 SECTION 2.0 REFERENCES 2.1 Standards Other References... 3

2 This page intentionally left blank.

3 September 2010 API Recommended Practice Standards The following standards, codes and specifications are cited in the recommended practice. Unless otherwise specified, the most recent editions of these documents shall apply. API API 510 API 530 API 570 RP 577 RP 578 RP 580 RP 581 RP 582 API 653 API 579-1/ ASME FFS Publ. 581 Std. 660 RP 751 RP 932-B RP 934-A RP 934-B RP 934-C RP 934-D RP 934-E RP 939-C RP 939-D RP 939-E RP 941 RP 945 Pressure Vessel Inspection Code Calculation of Heater Tube Thickness in Petroleum Refineries Piping Inspection Code Inspection, Repair, Alteration, and Rerating of In-Service Piping Systems Material Verification Program for New and Existing Alloy Piping Systems Welding Inspection and Metallurgy Recommended Practice for Risk Based Inspection Risk-Based Inspection Technology Welding Guidelines for the Chemical, Oil, and Gas Industries Tank Inspection, Repair, Alteration, And Reconstruction Fitness-For-Service Risk-Based Inspection - Base Resource Document Shell and Tube Heat Exchangers for General Refinery Service Safe Operation of Hydrofluoric Acid Alkylation Units Design, Materials, Fabrication, Operation and Inspection Guidelines for Corrosion Control in Hydroprocessing Reactor Effluent Air Cooler (REAC) Systems Materials and Fabrication Requirements for 2-1/4Cr-1Mo,2-1/4Cr-1Mo-1/4V, 3Cr 1Mo and 3Cr-1Mo-1/4V Steel Heavy Wall Pressure Vessels for High Temperature, High Pressure Service API Recommended Practice 934-B, Fabrication Considerations for ¼V Steel Heavy Wall Pressure Vessels for High Temperature, High Pressure Hydrogen Service Materials and Fabrication Requirements for 1 1/4Cr-1/2Mo Steel Heavy Wall Pressure Vessels for High Temperature, High Pressure Hydrogen Service Technical Report on the Materials and Fabrication Issues of 1¼ Cr - ½ Mo and 1 Cr - ½ Mo Steel Pressure Vessels, American Petroleum Institute, Washington, D.C. Recommended Practice for Materials and Fabrication of 1¼Cr-½Mo Steel Pressure Vessels for Service above 825 F (441 C), Guidelines for Avoiding Sulfidation Corrosion Failures in Oil Refineries Stress Corrosion Cracking of Carbon Steel in Fuel-Grade Ethanol: Review, Experience Survey, Field Monitoring, and Laboratory Testing Identification, Repair, and Mitigation of Cracking of Steel Equipment in Fuel Ethanol Service Steels for Hydrogen Service at Elevated Temperatures and Pressures in Petroleum Refineries and Petrochemical Plants Avoiding Environmental Cracking in Amine Units

4 2-2 API Recommended Practice Ballot September 2010 ASM 1 Metals Handbook Volume 1, Properties and Selection: Iron, Steels, and High-Performance Alloys; Volume 11, Corrosion in Petroleum Refining and Petrochemical Operations; Volume 13, Failure Analysis and Prevention ASME 2 Boiler and Pressure Vessel Code Boiler and Pressure Vessel Code Section III, Division I, Rules for Construction of Nuclear Power Plant Components. Section VIII Division 1 & 2, Rules for Construction of Pressure Vessels. ASTM 3 MNL41 STP1428 Corrosion in the Petrochemical Industry Thermo-mechanical Fatigue Behavior of Materials BSI 4 BSI 7910 Guidance on Methods for Assessing the Acceptability of Flaws in Fusion Welded Structures MPC 5 Report FS-26 Fitness-For Service Evaluation Procedures for Operating Pressure Vessels, Tanks and Piping in Refinery and Chemical Service 1 ASM International, 9639 Kinsman Road, Materials Park, OH , 2 ASME International, 3 Park Avenue, New York, NY , 3 ASTM International, 100 Barr harbor Drive, West Conshohocken, PA , www. astm.org 4 British Standard Institute, 389 Chiswick High Road, London W44AL, United Kingdom, 5 Materials Properties Council, 3 Park Avenue, 27 th Floor, New York, NY ,

5 NACE 6 Std. MR 0103 RP 0169 RP 0170 RP 0198 RP 0294 RP 0296 SP 0472 SP0590 SP0403 Publ. 5A151 Publ. 5A171 Publ. 8X194 Publ Publ Materials Resistant to Sulfide Stress Cracking in Corrosive Petroleum Refining Environments Standard Recommended Practice: Control of External Corrosion on Underground or Submerged Metallic Piping Systems Protection of Austenitic Stainless Steels and Other Austenitic Alloys from Polythionic Acid Stress Corrosion Cracking during Shutdown of Refinery Equipment The Control of Corrosion Under Thermal Insulation, and Fireproofing A Systems Approach Design, Fabrication, and Inspection of Tanks for the Storage of Concentrated Sulfuric Acid and Oleum at Ambient Temperatures Guidelines for Detection, Repair and Mitigation of Cracking of Existing Petroleum Refinery Pressure Vessels in Wet H 2 S Environments Methods and Controls to Prevent in-service Environmental Cracking of Carbon Steel Weldments in Corrosive Petroleum Refining Environments Prevention, Detection, and Correction of Deaerator Cracking Avoiding Caustic Stress Corrosion Cracking of Carbon Steel Refinery Equipment and Piping Materials of Construction for Handling Sulfuric Acid Materials for Receiving, Handling and Storing Hydrofluoric Acid Materials and Fabrication Practices for New Pressure Vessels used in Wet H 2 S Refinery Service Review and Survey of Alkaline Carbonate Stress Corrosion Cracking in Refinery Sour Water Effect of Nonextractable Chlorides on Refinery Corrosion and Fouling WRC 7 Bulletin 32 Bulletin 275 Bulletin 350 Bulletin 409 Bulletin 418 Bulletin 452 Graphitization of Steel in Petroleum Refining Equipment and the Effect of Graphitization of Steel on Stress-Rupture Properties The Use of Quenched and Tempered 2-1/4Cr-1Mo Steel for Thick Wall Reactor Vessels in Petroleum Refinery Processes: An Interpretive Review of 25 Years of Research and Application Design Criteria for Dissimilar Metal Welds Fundamental Studies Of The Metallurgical Causes And Mitigation Of Reheat Cracking In 1¼Cr-½Mo And 2¼Cr-1Mo Steels The Effect of Crack Depth (a) and Crack-Depth to Width Ratio (a/w) on the Fracture Toughness of A533-B Steel Recommended Practices for Local Heating of Welds in Pressure Vessels 2.2 Other References A list of publications that offer background and other information pertinent to the damage mechanism is provided in the section covering each damage mechanism. 6 7 NACE International, 1440 South Creek Drive, Houston, TX 77084, Welding Research Council, 3 Park Avenue, 27 th Floor, New York, NY ,