Compact cylinders ADNGF, standard port pattern

Size: px

Start display at page:

Download "Compact cylinders ADNGF, standard port pattern"

Charlotte Peters
6 years ago
Views:

2 Key features and type codes At a glance With guide rod and yoke plate ADNGF- With guide rod, yoke plate and through piston rod ADNGF- -S2 Cushioning types Mode of operation Application Cushioning P The drive is equipped with polymer flexible end-position cushioning Small loads Low speeds Small cushioning capacity Cushioning PPS The drive is equipped with selfadjusting, pneumatic end-position cushioning Larger loads Higher speeds Larger cushioning capacity Advantages No adjustment required Time-saving No adjustment required Up to four times greater cushioning capacity than ADNGF- -P Time-saving Noise reduction Type codes ADNGF P A S6 Type Double-acting ADNGF Compact cylinder Piston [mm] Stroke [mm] Cushioning P PPS Flexible cushioning rings/pads at both ends Pneumatic cushioning, self-adjusting at both ends Position sensing A Via proximity sensor Variant S2 Through piston rod S6 Heat-resistant seals up to max. 120 C TL Captive rating plate 2 Internet: Subject to change 2018/04

3 Peripherals overview ae 1 3 ad aj aa ab ac Mounting attachments and accessories 1 Flange mounting FNC 2 Swivel flange SNCL/SNCL- -R3 3 Swivel flange SNCB/SNCB- -R3 4 Multi-position kit DPNA 5 Trunnion flange ZNCF/CRZNG 6 Trunnion support LNZG 7 Swivel flange SNCS/CRSNCS/SNCS- -R3 8 Clevis foot LBG/LBG- -R3 9 Proximity sensor SME-8 aj Proximity sensor SME/SMT-8M aa Slot cover ABP-5-S ab Proximity sensor SMPO-8E ac Mounting kit SMB-8E ad One-way flow control valve GRLA/GRLZ ae Push-in fitting QS Description Page/Internet For end caps 11 For end caps 12 For end caps 16 For connecting two cylinders with identical piston diameters to form a multi-position cylinder 15 For end caps 17 For trunnion flange ZNCF/CRZNG 18 For end caps 13 For swivel flange SNCS 14 Can be integrated in the cylinder profile barrel 20 Can be integrated in the cylinder profile barrel 20 For protecting the sensor cable and keeping dirt out of the sensor slots 20 Pneumatic output signal 21 For proximity sensor SMPO-8E 21 For regulating speed 19 For connecting compressed air tubing with standard O.D. qs 2018/04 Subject to change Internet: 3

4 Technical data Function P cushioning Variants S2 S6 PPS cushioning -W- -N- Diameter mm -T- Stroke length mm General technical data Piston Pneumatic connection M5 M5 M5 M5 G1/8 G1/8 G1/8 G1/8 G1/8 G1/8 Design Piston Piston rod Cylinder barrel Mode of operation Double-acting Cushioning P Flexible cushioning rings/pads at both ends PPS Pneumatic cushioning, self-adjusting at both ends Cushioning length PPS [mm] Position sensing Via proximity sensor Type of mounting Via through-hole / via female thread / via accessories Mounting position Any Operating and environmental conditions Piston Operating medium Compressed air in accordance with ISO :2010 [7:4:4] Note on operating/pilot medium Operation with lubricated medium possible (in which case lubricated operation will always be required) Operating pressure [bar] PPS S Ambient temperature 1) [ C] S Corrosion resistance class CRC 2) 2 1) Note operating range of proximity sensors 2) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Weight [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke Internet: Subject to change 2018/04

5 Technical data Forces [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing S Theoretical force at 6 bar, retracting S Max. impact energy in the end positions S H- Note In combination with PPS cushioning, the maximum impact energy is still obtained. Max. energy conversion capacity [J] Piston For PPS cushioning Max. lateral force Fq as a function of projection x Torque M as a function of stroke length l Fq [N] M [Nm] x [mm] l [mm] 12/16 20/ /63 80/100 12/ Materials Sectional view Compact cylinder Basic version S6 1 Cap Anodised aluminium 100 Die-cast aluminium, coated 4 2 Cylinder barrel Anodised aluminium 3 Piston rod High-alloy steel 4 Flange screws High-alloy steel Galvanised steel Standard screws, galvanised steel Seals Polyurethane Fluoro elastomer 2018/04 Subject to change Internet: 5

6 Technical data Dimensions Basic version Download CAD data + = plus stroke length = plus stroke length [mm] BG min. D1 H9 D4 ±0,1 D5 D6 D7 H9 D8 E EE FB H8 G J2 J F M M M F M F M6 22 G1/ M M LA ME MM PL RT SF T1 T2 TG WH ZA ZB [mm] +0.2 h h ± PPS +1.4 ± PPS M M M M M Internet: Subject to change 2018/04

7 Technical data Dimensions Variant S2 Through piston rod Download CAD data + = plus stroke length ++ = plus 2x stroke length AF KF T4 WH ZM PPS PPS [mm] min M M M M M M /04 Subject to change Internet: 7

8 Technical data Ordering data Type Piston Stroke [mm] P Flexible cushioning rings/pads at both ends [mm] [mm] Part No. Type Part No. Type ADNGF-12-5-P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A PPS Pneumatic cushioning, self-adjusting at both ends ADNGF-16-5-P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF P-A ADNGF-20-5-P-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF-25-5-P-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF-32-5-P-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A 8 Internet: Subject to change 2018/04

9 Technical data Ordering data Type Piston Stroke [mm] P Flexible cushioning rings/pads at both ends PPS Pneumatic cushioning, self-adjusting at both ends [mm] [mm] Part No. Type Part No. Type ADNGF-40-5-P-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF-50-5-P-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A ADNGF P-A ADNGF PPS-A 2018/04 Subject to change Internet: 9

10 Ordering data Modular products Ordering table Size Conditions 0M Module No Function Compact cylinder, double-acting, standard hole pattern ADNGF ADNGF Size [mm] Stroke [mm] Cushioning Flexible cushioning rings/pads at both ends -P Pneumatic cushioning, self-adjusting at both ends 1 -PPS Position sensing Via proximity sensor -A -A 0O Piston rod type Through piston rod -S2 Temperature resistance Heat-resistant seals up to max. 120 C 2 -S6 Captive rating plate Laser etched rating plate -TL Code Enter code 1 PPS Not with temperature resistance S6 Minimum stroke 5 mm 2 S6 Max. stroke: 250 mm M O Mandatory data Options Transfer order code ADNGF A 10 Internet: Subject to change 2018/04

Flange mounting FNC 32 100 12 25 Material: Galvanised steel Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and ordering data For E FB MF R TF UF ZF CRC 1) Weight Part No.

11 Flange mounting FNC Material: Galvanised steel Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and ordering data For E FB MF R TF UF ZF CRC 1) Weight Part No. Type [mm] 1 [g] FNC FNC FNC FNC FNC FNC FNC FNC FNC FNC-100 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). 2018/04 Subject to change Internet: 11

12 Swivel flange SNCL/SNCL- -R3 Material: SNCL 12 25: Wrought aluminium alloy SNCL : Die-cast aluminium SNCL- -R3: Wrought aluminium alloy with protective coating Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and ordering data For CD E EW FL L MR TG XC [mm] H h h / / / / / / / / For Basic version R3 High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] SNCL SNCL-12-R SNCL SNCL-16-R SNCL SNCL-20-R SNCL SNCL-25-R SNCL SNCL SNCL SNCL SNCL SNCL-100 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. 12 Internet: Subject to change 2018/04

Swivel flange SNCS/CRSNCS/SNCS- -R3 Materials: SNCS 32 50: Die-cast aluminium SNCS 63 100: Wrought aluminium alloy CRSNCS 32 80: High-alloy stainless steel SNCS- -R3 100: Wrought aluminium alloy with

13 Swivel flange SNCS/CRSNCS/SNCS- -R3 Materials: SNCS 32 50: Die-cast aluminium SNCS : Wrought aluminium alloy CRSNCS 32 80: High-alloy stainless steel SNCS- -R3 100: Wrought aluminium alloy with protective coating RoHS-compliant + = plus stroke length Dimensions and ordering data For CN E EP EX FL [mm] ADNGF- ADNGF- -R3 ADNGF- ADNGF- -R3 ±0.2 ± / / / / / ,5± / ,2± / / / For LT MS RA TG XC ADNGF- ADNGF- -R3 ADNGF- ADNGF- -R3 [mm] ±0.5 30± For Basic version High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] SNCS CRSNCS SNCS CRSNCS SNCS CRSNCS SNCS CRSNCS SNCS CRSNCS SNCS SNCS-100-R3 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 2018/04 Subject to change Internet: 13

14 Clevis foot LBG/LBG- -R3 The clevis foot is secured against rotation with a dowel pin. Material: LBG 32 63: Special steel casting LBG : Nodular graphite cast iron LBG- -R3: High-alloy stainless steel Free of copper and PTFE RoHS-compliant Dimensions and ordering data For CL CM EK [mm] FL GL HB L2 LE MR RF RG S UK UX For Basic version R3 High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] LBG LBG-32-R LBG LBG-40-R LBG LBG-50-R LBG LBG-63-R LBG LBG-80-R LBG LBG-100-R3 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. 14 Internet: Subject to change 2018/04

Multi-position kit DPNA Material: Flange: Wrought aluminium alloy Screws: Galvanised steel Free of copper and PTFE RoHS-compliant + = plus stroke length -H- Note The maximum overall stroke length may

15 Multi-position kit DPNA Material: Flange: Wrought aluminium alloy Screws: Galvanised steel Free of copper and PTFE RoHS-compliant + = plus stroke length -H- Note The maximum overall stroke length may not be exceeded when combining cylinders and multi-position kits. Dimensions and ordering data For L2 B1 Max. CRC 1) Weight Part No. Type overall stroke length [mm] [mm] [g] DPNA DPNA DPNA DPNA DPNA DPNA DPNA DPNA DPNA DPNA-100 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 2018/04 Subject to change Internet: 15

16 Swivel flange SNCB/SNCB- -R3 Material: SNCB: Die-cast aluminium SNCB- -R3: Die-cast aluminium with protective coating Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and ordering data For CB E EK FL L MR TG UB XC [mm] H14 H9/e h / / For Basic version R3 High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] SNCB SNCB-32-R SNCB SNCB-40-R SNCB SNCB-50-R SNCB SNCB-63-R SNCB SNCB-80-R SNCB SNCB-100-R3 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. 16 Internet: Subject to change 2018/04

Trunnion flange ZNCF/CRZNG Material: ZNCF: Special steel casting CRZNG: Electrolytically polished special steel casting Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and

17 Trunnion flange ZNCF/CRZNG Material: ZNCF: Special steel casting CRZNG: Electrolytically polished special steel casting Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and ordering data For C2 C3 TD TK TL TM US XH XL [mm] e For Basic version R3 High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG-100 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 2018/04 Subject to change Internet: 17

Trunnion support LNZG Material: Trunnion support: Anodised aluminium Plain bearing: Plastic Free of copper and PTFE RoHS-compliant Dimensions and ordering data For CR DA FK FN FS H1 HB KE NH TH UL

18 Trunnion support LNZG Material: Trunnion support: Anodised aluminium Plain bearing: Plastic Free of copper and PTFE RoHS-compliant Dimensions and ordering data For CR DA FK FN FS H1 HB KE NH TH UL CRC 1) Weight Part No. Type [mm] D11 H13 ±0.1 H13 ±0.2 [g] LNZG-32 40, LNZG-40/50 63, LNZG-63/ LNZG-100/125 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 18 Internet: Subject to change 2018/04

19 Ordering data One-way flow control valves Connection Material Part No. Type For For tubing O.D. Technical data Internet: grl For exhaust air 12, 16, 20, 25 3 Metal design GRLA-M5-QS-3-D GRLA-M5-QS-4-D GRLA-M5-QS-6-D 32, 40, 50, 63, 80, GRLA-1/8-QS-3-D GRLA-1/8-QS-4-D GRLA-1/8-QS-6-D GRLA-1/8-QS-8-D For supply air 12, 16, 20, 25 3 Metal design GRLZ-M5-QS-3-D GRLZ-M5-QS-4-D GRLZ-M5-QS-6-D 32, 40, 50, 63, 80, GRLZ-1/8-QS-3-D GRLZ-1/8-QS-4-D GRLZ-1/8-QS-6-D GRLZ-1/8-QS-8-D 2018/04 Subject to change Internet: 19

20 Ordering data Proximity sensors for T-slot, magneto-resistive Type of mounting Switch output Technical data Internet: smt Electrical connection Cable length Part No. Type [m] N/O contact Insertable in the slot from above, flush with cylinder profile, short design PNP Cable, 3-wire SMT-8M-A-PS-24V-E-2,5-OE Plug M8x1, 3-pin SMT-8M-A-PS-24V-E-0,3-M8D Plug M12x1, 3-pin SMT-8M-A-PS-24V-E-0,3-M12 NPN Cable, 3-wire SMT-8M-A-NS-24V-E-2,5-OE Plug M8x1, 3-pin SMT-8M-A-NS-24V-E-0,3-M8D N/C contact Insertable in the slot from above, flush with cylinder profile, short design PNP Cable, 3-wire SMT-8M-A-PO-24V-E-7,5-OE Ordering data Proximity sensors for T-slot, magnetic reed Type of mounting Switch output Technical data Internet: sme Electrical connection Cable length Part No. Type [m] N/O contact Insertable in the slot from above, flush with cylinder profile Insertable in the slot lengthwise, flush with the cylinder profile Contacting Cable, 3-wire SME-8M-DS-24V-K-2,5-OE SME-8M-DS-24V-K-5,0-OE Cable, 2-wire SME-8M-ZS-24V-K-2,5-OE Plug M8x1, 3-pin SME-8M-DS-24V-K-0,3-M8D Contacting Cable, 3-wire SME-8-K-LED-24 Plug M8x1, 3-pin SME-8-S-LED-24 N/C contact Insertable in the slot lengthwise, flush with the cylinder profile Contacting Cable, 3-wire SME-8-O-K-LED-24 Ordering data Connecting cables Technical data Internet: nebu Electrical connection, left Electrical connection, right Cable length Part No. Type [m] Straight socket, M8x1, 3-pin Cable, open end, 3-wire NEBU-M8G3-K-2.5-LE NEBU-M8G3-K-5-LE3 Straight socket, M12x1, 5-pin Cable, open end, 3-wire NEBU-M12G5-K-2.5-LE NEBU-M12G5-K-5-LE3 Angled socket, M8x1, 3-pin Cable, open end, 3-wire NEBU-M8W3-K-2.5-LE NEBU-M8W3-K-5-LE3 Angled socket, M12x1, 5-pin Cable, open end, 3-wire NEBU-M12W5-K-2.5-LE NEBU-M12W5-K-5-LE3 20 Internet: Subject to change 2018/04

21 Ordering data Rectangular proximity sensors, pneumatic Technical data Internet: smpo Pneumatic connection Part No. Type 3/2-way valve, normally closed Female thread M SMPO-8E Ordering data Mounting kit for proximity sensors SMPO-8E Technical data Internet: smb Assembly Part No. Type Clamped in T-slot SMB-8E Ordering data Slot cover for T-slot Assembly Length Part No. Type Insertable from above 2x 0.5 m ABP-5-S 2018/04 Subject to change Internet: 21

Compact cylinders ADNGF, standard port pattern

Compact cylinders ADNGF, standard port pattern Key features and type codes At a glance With guide rod and yoke plate ADNGF- With guide rod, yoke plate and through piston rod ADNGF- -S2 Cushioning types Mode of operation Application Cushioning P The