TECHNICAL CATALOGUE

Transcription

1

2

3 TECHNICAL CATALOGUE 2017

4 index: About JPC 6 Olefin Products 12 Chemical Products 20 HDPE Products 24 LLDPE Products 38

5 About JPC About JPC... 6 Vision, Mission, Values, Objectives... 9 JPC in the Global Markets Olefin Products Olefin plant Capacity Ethylene Propylene Pyrolysis gasoline C4 cut Fuel oil Chemical Products Butadiene Butene HDPE Products Product Capacity of HDPE plant HF-4760(BL3) HM-8355(BL4) HM-5010T2N (EX3) HMCRP 100 N(PE100) HM CRP 100 Black HM9450F(EX5) LLDPE Products Product Capacity of LLDPE plant AA/22502KJ AA/22501KJ HP-LL18XF5/N HD5000s /UV HD-60507/UV /UV CC CC CC52502SU HD-52505/UV /UV HD UV UV... 66

6 About JPC (JPC) (private joint stock) was incorporated in 2000 along the lines of large scale programs of the country to exploit South Pars Gas Field. This huge industrial complex was constructed on the land of about 77 hectares in the South Pars Economic Zone situated in Asaluyeh, Bushehr. South Pars Gas Field, one of the biggest gas resources of the world, is located on the border shared with Iran and Qatar in the Persian Gulf, being 105 km to the south west of Asaluyeh Port. This Gas Field is extended over an area of 9,700 km2, of which 3,600 km2 is situated within Iranian waters. With approximately 14 trillion m3 gas, South Pars Gas Field accounts for 50 percent of the state s gas reservoirs. 6

7 After almost a decade of commissioning, this Gas Field with its olefin, linear low and high density polyethylene, butadiene and butene-1 continues to be one of the largest producers of olefin in the world and of polymer products in Iran. As the most distinguished productive complex in the South Pars Economic Zone, JPC produces and supplies various grades of petrochemical products in domestic and foreign markets. Constantly taking steps toward development, JPC is regarded as one of the most important petrochemical industrial complexes in the realm of economy. JPC production strategy, ceaseless improvement of value chain processes, customer orientation through the provision of high quality products and services as per international standards, and highly competent and committed personnel have been provided, and provides, this enterprise with endless and strong support for the achievement of its objectives and further allows it to continue to mount to the higher status in the world. 7

8 8

9 Vision To turn into the biggest producer of olefin and its value chain in Iran up to Mission As a producer of olefin and its value chain, JPC relies on its capabilities and merits to create value for all beneficiaries for the ultimate purpose of improving human being quality of life globally. Values Being ambitious and seeking excellence; Honoring human dignity; Being knowledge oriented; and Being accountable and responsible against beneficiaries. Objectives 1. Developing and completing the value chain of the production of olefin s basic materials; 2. Enhancing flexibility and creating diversity in production of products tailored to the market needs; 3. Developing leadership relations and partnership with other enterprises to create higher value for JPC; 4. Constantly enhancing structures, systems, processes and managerial procedures so as to promote JPC s productivity; 5. Designing and operationalizing integrated information management and knowledge management systems; 6. Utilizing the latest scientific and technological advances achieved all around the world for organizational training and excellence; 7. Ceaselessly creating value for clients and strengthening competitive advantages at the international level; 8. Institutionalizing and constantly improving our relationship with clients and other beneficiaries; 9. Continuously reinforcing moral values and attending to social responsibilities; and 10. Attracting, preserving, developing and employing human resources in a way consistent with JPC s strategic requirements. 9

10

11 JPC in the Global Markets JPC is among one of the largest exporters of Iranian polymer products. JPC continues to be ranked first for the export of high density polyethylene products. Eighty percent of JPC products are exported to more than 20 commercial destinations all around the world. One important market targeted by JPC is that of Chinese; however, JPC reduced its Chinese market share as part of its policies in order to abate commercial risks thereof. At the moment, China, Turkey, CIS, the Far East, European ports and neighboring countries serve as the entryway of JPC products to international markets. Africa and South America are another potential markets which are expected to allocated themselves a considerable part of JPC export. JPC endeavors to enhance its share of target markets and at the same time places great emphasis on potential markets.

12 1

13 Olefin Products

14 Product Capacity of Olefin plant Products Production Capacity 1000 T/Y Saleable Products 1000 T/Y Applications Ethylene Polyethylenee, PVC Propylene Polypropylene C 4 cut 265 Feed for downstream plant Pyrolysis gasoline To Aromatic Plant Fuel Oil Feed for downstream plant Hydrogen 1.5 For hydrogenation Methane 3.9 Fuel Total

15 Product data sheet Olefin made via Techinp Tecnology Ethylene Is a simple olefin, the chemical formula is C 2 H 4 has a prominent role in the petrochemical industry. It is colorless flamable gas. COMPONENT SPECIFICATION Ethylene Methane + Ethane Ethane Acetylene C3 & Higher Carbon Monoxide Carbon Dioxide Water Oxygen Hydrogen Nitrogen Oxygenated Compounds Basic Nitrogen Compounde Caloulated as NH3 Total sulphur Methanol Total Combined Nitrogen COS Mercaptans vol % min ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max ppm vol max mg/kg max ppm vol max ppm vol max ppm vol max ppm vol max 15

16 Product data sheet Olefin made via Techinp Tecnology Propylene Also called propane, a colorless, flamable, gaseous hydrocarbon, C3H6, obtained from low molecular weight constituents of petroleum. COMPONENT Propylene Propane Hydrogen Ethylene Butenes Pentenes Non-condensables Ethane Butane-pentanes C6-C12 Hydrocarbons Acetylene Methyl-acetylene Propadiene Butadiene Oxygen Carbon Monoxide Carbon Dioxide COS Total sulphur Methanol Isopropanol Water Arsine Phosphine Ammonia Cyclopentadiene Unit % vol % vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm vol ppm wt ppm vol ppm vol ppm wt ppm vol ppm vol ppm wt ppm vol SPECIFICATION min 99.8 max 0.2 % max 5 max 1 max 1 max 1 max 20 max 20 max 10 max 1 max 1 max 1 max 1 max 10 max 2 max 0.03 max 2 max 0.02 max 1 max 5 max 5 max 2 max 0.01 max 0.01 max 1 max

17 Product data sheet Olefin made via Techinp Tecnology Pyrolysis gasoline Pyrolysis gasoline, is a naphtha-range product with a high aromatics content used either for gasoline blending or as a feed stock for aromatics plants. SPECIFICATION Aromatics Benzene Toluene Density at 15.6C FBP IBP R.V.P Paraffines Isoparaffines Naphtenes Olefins Total Sulfur Gum Content Lead Content Water Content Unknown Residue %5Recovery 10%Recovery 20%Recovery 30%Recovery 40%Recovery 50%Recovery 60%Recovery 70%Recovery 80%Recovery 90%Recovery Recovery Color Sybolt Unit wt% wt% wt% gr/cm3.c.c kpa wt% wt% wt% wt% mg/kg mg/100ml ppb wt% wt%.c.c.c.c.c.c.c.c.c.c.c Spec. max 50 max max 225 min max 21 max 21 max 2 max max 50 max min min Analysis Method ASTM D4052 ASTM D86 ASTM D86 ASTM D6378 ASTM D5453 ASTM E203 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 ASTM D86 17

18 Product data sheet Olefin made via Techinp Tecnology C4 Cut C4 Cut produced in Ethylene production planets by steam cracking of naphtha. It is a mixture of C 4 hydrocarbons mainly 1,3- butadiens, Iso Butene, Butane. COMPONENT 1,3-Butadiene Methyl-Acetylene Propadiene Propylene Propane Vinyl-Acetylene i-butene 1 Butene Cis2-Butene Trans2-Butene i-butane n-butane C5-diolefins Pentenes Pentanes 2-methyl-butene Total SPECITICATION 45.1 %wt 0.12 %wt 0.02 %wt 0.1 %wt 0.03 %wt 1.13 %wt 19.2 %wt 9.16 %wt 1.86 %wt 2.58 %wt 3.94 %wt %wt 0.06 %wt 0.1 %wt 0.02 %wt 0.03 %wt %wt 18

19 Product data sheet Olefin made via Techinp Tecnology Fuel Oil Fuel oil product is a heavy hydrocarbon cut rich (poly) aromatic components. TEST/COMPOSITION Flash point Viscosity VALUE >60 C approx. >40 cp at 80 C 19

20 2

21 Chemical Products

22 Product data sheet Butadiene made via BASF Tecnology Butadiene 1,3-Butadiene is a simple diene with the formula C4H6. It is an important industrial chemical used as a monomer in the production of synthetic rubber. Annual production 115,000 tons Analysis Unit Specification Analysis Method 1,3 - Butadiene wt % Min ASTM D ,2 - Butadiene wt ppm Max. 100 ASTM D 2593 Total Butenes wt % Max. 0.5 ASTM D 2593 Total Acetylenes wt ppm Max. 60 ASTM D 2593 TBC wt ppm BASF's method Dimer (VCH) wt % Max. 0.1 ASTM D 2426 Peroxides wt ppm Max. 5 BASF's method Non Volatile Residue wt % Max. 0.1 BASF's method Total Sulfur wt ppm Max. 5 ASTM D 5453 Oxygen in Vapor Phase mol % Max. 0.2 PORTABLE TRACE OXYGEN ANALYZER 22

23 Product data sheet Butene-1 made via Axense Tecnology Butene-1 Butene-1 is a linear alpha-olefin with the formula C4H8 and used as a co-monomer for the production of HDPE & LLDPE and manufacturing of polybutene. Annual production 100,000 tons Analysis Unit Specification Analysis Method Butene-1 wt % Min ASTM D 4424 C6+ wt ppm Max. 100 ASTM D 4424 C4s (Butenes + Butanes) wt % Max. 0.5 ASTM D 4424 Ethylene wt ppm Max. 500 ASTM D 4424 Ethane wt ppm Max. 100 ASTM D 4424 Acetylenes wt ppm Max. 15 ASTM D ,3-Butadiene wt ppm Max. 20 ASTM D 4424 Carbon monoxide wt ppm Max. 1 ISO Carbon dioxide wt ppm Max. 1 ISO Water wt ppm Max. 15 ASTM D 2029 Total Sulphur wt ppm Max. 1 ASTM D

24 3

25 HDPE Products

26 Product Capacity of HDPE plant GRADES PROPERTY UNIT MFR (190 C/2.16 kg) (g/10 min). Density g/l ASTM METHOD D 1238 ISO 1183 INTERNAL METHOD INJECTION MOLDING HC 7260 HC 7260 * HD 7255 HD 7255* for transport and stacking bottle crates,particularty bottle creates for transport and stacking bottle crates,particularty bottle creates for thick walled highly stressed transport container,e.g. refuse bins and fish crates for thick walled highly stressed transport container,e.g. refuse bins and fish crates 23±3 23±3 11±2 11± ± ± ± ± SMALL BLOW MOLDING Available HF 4750 HF 4760 (BL3) HH 4765 for disinfectant bottles up to 2 liters, tubes for cosmetics, containers up to 10 liters and petrol cans up to 5 liters for container with capacites ranging from a few ml up to 10liters, alsofor production of sheets for thermoforming for hollow articles where high stress cracking resistance is not demanded,such as bottles and caisters up to 10 liters,e.g. for fabric softeners 1.1± ± ± ± ± ± LARGE BLOW MOLDING Available HM 8355 general-purpose grade for large containers 0.25± ± STRETCHED TAPE (RAFFIA) HF 7740 F HF 7740 F2 stretched films and tapes for production of high-strength knitted and woven tapes to be used for agricultural packagings and as protective cover 1.8± ± ± ± MONOFILAMENT HF 7750 M HF 7750 M2 production of monofilaments with high tensile strength monofilaments for fishing notes, geo textiles and civil engineering 2.5± ± ± ±

27 Product Capacity of HDPE plant GRADES PROPERTY UNIT MFR (190 C/2.16 kg) (g/10 min). Density g/l ASTM METHOD D 1238 ISO 1183 INTERNAL METHOD CABLE HF 4750 K cable insulation 3.5± ± PIPE(NATURAL/COLOR) Available Available Available HM 5010 T2 N HM 5010 T3 N HM 5010 T3 Black HM CRP 100 N HM CRP 100 Black HM CRP 100 Blue HM CRP 100 O/Y pressure pipes, e.g. drinking-water and gas pipes,waste pipes and sewer pipes,their fittings and also sheets(uv stabilization and pigments during processing) high-quality PE 80 pressure pipes for gas and water transportation(uv stabilization and pigments during processing) high-quality PE 80 pressure pipes for gas and water transportation(uv stabilization and pigments during processing) top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing) top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing) top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing) top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing) 0.45± ± ± ± ± ± ± ± ± ± ± ± ± ± FILM Available HM 9455 F HM 9450 F HM 9450 F1 HM 9455 F1 HM 9445 HT for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing and sealability for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing 0.28± ± ± ± ± ± ± ± ± ±

28 Product data sheet HDPE made via Hostalen Process HF-4760 (BL3) HF-4760 (BL3) is a blow molding grade resin which is manufactured by suspension polymerization of ethylene monomer. HF-4760 (BL3) is a bi-model high density polyethylene with 1-Butene as co monomer. HDPE: HF-4760(BL 3 ) Density: g/cm3 MFR 190/5: Characteristic Properties Main Applications Additives High density and Stiffness, good flowabilitty and impact Strenght and good Stress Cracking resistance. For container with capacities ranging from a few ml up to 10 liters, also for production of sheets for thermoforming. Antioxidant/Process stabilizer Lubricant/ acid scavenger Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Melt Index(21.6) Melt Index(5) FRR (21.6/5) Density Moulded Properties Notched 23 C Unit )g/10 min( )g/10 min( g/cm³ Unit mj/mm² Typical Value Typical Value 9 Test Method ISO 1133 ISO 1133 ISO 1183 Test Method ISO 179/ 1 ea 28

29 29 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery. - On compression moulded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 29

30 Product data sheet HDPE made via Hostalen Process HM-8355 (BL4) HM-8355(BL4) is a Blow molding grade resin which is manufactured by suspension polymerization of ethylene monomer. HM-8355 (BL4) is a bu-modal high density polyethylene with Butene-1 as co monomer with general purpose of large container. HDPE: HM-8355(BL4) Density: g/cm3 MFR 190/5: Characteristic Properties Main Applications Additives High molar mass, easily processable high stiffness strenght, good stress Cracking resistance and very good molding surface finish. General purpose grade for large container. Antioxidant/Process stabilizer Lubricant/ acid scavenger Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Melt Index(21.6) Melt Index(5) FRR (21.6/5) Density Swell Ratio Moulded Properties Notched 23 C Unit )g/10 min( )g/10 min( g/cm³ % Unit mj/mm² Typical Value Typical Value 10 Test Method ISO 1133 ISO 1133 ISO 1183 Test Method ISO 179/ 1 ea 30

31 31 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery. - On compression moulded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 31

32 Product data sheet HDPE made via Hostalen Process HM-5010T2N (EX3) HM-5010T2N (EX3) is a pipe grade resin which is manufactured by the suspension polymerization of ethylene monomer. HM-5010T2N (EX3) is a bi-model high density polyethylene with 1-Butene as co monomer. HDPE: HM-5010T2N (EX 3 ) Density: g/cm3 MFR 190/5: Characteristic Properties Main Applications Additives Tough and rigid pipe resin. Pressure pipes, e.g. drinking-water and gas pipes, waste pipes and sewer pipes, their fittings and also sheets (UV stabilization and pigments during processing) Antioxidant/Process stabilizer Lubricant (processing aid)/ acid scavenger Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Melt Index (21.6) Melt Index (5) FRR (21.6/5) Density Moulded Properties Notched 23 C Mechanical Properties Hydrostatic Strenght (80 ºC) Unit )g/10 min( )g/10 min( g/cm³ Unit mj/mm² Unit h Typical Value Typical Value 12 Typical Value (4.0 N/mm²) 1000 Test Method ISO 1133 ISO 1133 ISO 1183 Test Method ISO 179/ 1 ea Test Method ISO

33 33 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery. - On compression moulded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 33

34 Product data sheet HDPE made via Hostalen Process HMCRP 100N (PE100) -M-CRP100N (PE100) is a natural pipe grade resin shich is manufactured by suspension polymerization of ethylen monomer, HM-CRP100N )PE100) is a bi-model high density polyethylene with 1-Butene as co monomer. HDPE: HMCRP 100 N (PE100) Density: g/cm3 MFR 190/5: Characteristic Properties Main Applications Additives Natural PE100 pipe resin. Top quality PE100 pressure Pipes for gas and water transportaion at higher pressures or with thinner walls as PE80 (UV stabilization and/ or pigments during precessing) Antioxidant/Process stabilizer Lubricant (processing aid)/ acid scavenger Material properties (This data are typical values and are not to be construed as product specifications.) Test/Composition Density FRR 21.6/5 Hydrostatic Strength (80 c) MFR190 /21.6 MFR190 /5 Notched Impact (23 c) Typical Value (4.5N/mm 2 ) Unit g/ml 3 h (g/10 min) (g/10 min) mj/mm 2 ASTM Method ISO1183 ISO1167 ISO1133 ISO1133 ISO179/1eA - Test specimen from compression moulded sheet at 23 C. - FRR values are statistical and calculated by dividing MFR values. - Notch Impact Test specimen from compressed moulded sheet 23 C and The data quoted are average values. 34

35 Product data sheet HDPE made via Hostalen Process HM CRP 100 Black HM-CRP100 Black is a black pipe grade resin (PE100) which is manufactured by suspension polymerization of ethylene monomer. HM- CRP100 Blue is a bi-model high densit polyethylene with 1-Butene as co monomer. HDPE: HM CRP 100 Black (PE100 Black) Characteristic Properties Density: g/cm3 Main Applications MFR 190/5: Additives Black PE100 resin Top quality PE100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE80 Antioxidant/Process stabilizer Lubricant (processing aid)/ acid scavenger Carton Black Material properties (This data are typical values and are not to be construed as product specifications.) Test/Composition Density FRR 21.6/5 Hydrostatic Strength (80 c) MFR190 /21.6 MFR190 /5 Notched Impact (23 c) Typical Value (4.5N/mm 2 ) Unit g/ml 3 h (g/10 min) (g/10 min) mj/mm 2 ASTM Method ISO1183 ISO1167 ISO1133 ISO1133 ISO179/1eA - Test specimen from compression moulded sheet at 23 C. - FRR values are statistical and calculated by dividing MFR values - Test specimen from compressed moulded sheet 23 C sheet 23 ºC - The data quoted are average values - The data quoted are average values 35

36 Product data sheet HDPE made via Hostalen Process HM9450F (EX5) HM-9450F (EX5) is blown film grade resin which is manufactured by suspension polymerization of ethylen monomer. HM-9450F (EX5) is a bi-model high density polyethylene with 1-Butene as co monomer. HDPE: HM9450F (EX5) Density: g/cm3 MFR 190/5: Characteristic Properties Main Applications Additives High molar mass film grade, good stiffness and tenacity For blown films with paperlike quality, sutable for counter bags, carrier bags and wrapping films, excellent processing. Antioxidant/Process stabilizer Lubricant (processing aid)/ acid scavenge Material properties (This data are typical values and are not to be construed as product specifications.) Test/Composition Typical Value Unit Method Density g/cm 3 ISO1183 Fish Eye Note 3 note Internal FRR 21.6/5 29 MFR 190 / g/10min ISO1133 MFR190 / g/10min ISO Test specimen from compression moulded sheet at 23 C. - FRR values are statistical and calculated by dividing MFR values. - Notch Impact Test specimen from compressed moulded sheet 23 C and The data quoted are average values 36

37

38 4

39 LLDPE Products

40 Product Capacity of LLDPE plant Available Available Available GRADES 1- LLDPE Butene 235F / AA/ KJ 22501/ AA/ KJ PROPERTY UNIT ASTM METHOD INTERNAL METHOD Lamination Liner General Purpose High Stiffness Cast & general Purpose Cast 2- Terpolymer - HP-LLDPE SPECIALITY PRODUCTS 12XF6 12HF6 14ZF8 14XF9 12X01 14X01 11X02 09X02 20X02 18XF5 N High Performance Shrink Easy Processability Lamination Superbutene High Stiffness General Purpose Stretch cast Bread bags High performance 3- Quattropolymer'' HP-LLDPE SPECIALTTY PRODUCTS (HP HEXENE TYPE) MFR (190 C/2.16 kg) (g/10 min). D ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± 0.10 Density g/l D ± ± ± ± ± ± ± ± ± ± ± ± 2 18YF3 18YF5 12YF6 15YF6 11YF6 14Y01 10Y02 Shrink film, high perform. High Stiffness/ Shrink Liner Heavy duty Lamination high clarity Thin film High Pre-Stretch cast 0.30 ± ± ± ± ± ± ± ± ± ± ± 1 4- VLDPE (butene) film grades SPECLALITY GRADES Lamination Cast- Co-extrusion ( * ) 2.50 ± ± ± ± 1 ( * ) This product is used as adhesive layer in a multilayer co-extruded film. 40

41 Product Capacity of LLDPE plant GRADES PROPERTY UNIT MFR (190 C/2.16 kg) (g/10 min). Density g/l ASTM METHOD D 1238 D 1505 INTERNAL METHOD HP-VLDPE SPECIALITY PRODUCTS 01X01 02X02 Co-extrusion Geomembranes, Bumpers, Soft Nets 0.90 ± ± ± ± 1 6- HDPE - Medium MWD - Stretched Available Jamlene HD-5000s 424F5 534F Monofilament Raffia (Textile grade) Monofilament, high tenacity Monofilament 0.80 ± ± ± ± ± ± ± ± 2 New 7- HP-HDPE (@) SPECIALITY PRODUCTS 36XF6 43X01 41X01 Raffia for ropes Monofilament Cast flat yarn (Raffia) 0.60 ± ± ± ± ± ± 1 8- HDPE Narrow MWD - Homopolymer injection moulding grades Available Available Available / UV / UV / UV Crates Crates Houseware Fast cycle Thin walled 5.50 ± ± ± ± ± ± ± ± ± ± 2 9- HDPE Narrow MWD - Copolymer injection moulding grades Available Available Available Available Available Available CC CC CC 52502SU / UV / UV Caps and closures (CSD) Caps and closures (Mineral water, CSD) Caps and closures (CSD) Containers Houseware Houseware, High fluidity Caps, Thin walled 0.90 ± ± ± ± ± ± ± ± ± ± ± ± ± ± 2 New New New 10- LLDPE (butene) Injection moulding grades General purpose General purpose Lids Fast Cycle 5.00 ± ± ± ± ± ± ± ± 1 41

42 Product Capacity of LLDPE plant GRADES 11- LLDPE (butene) Extrusion coating PROPERTY UNIT ASTM METHOD INTERNAL METHOD MFR (190 C/2.16 kg) (g/10 min). D Density g/l D Extrusion coating 7.00 ± ± LLDPE Rotomoulding Available Available UV UV UV UV Rotomoulding, high-escr Rotomoulding, high-escr Rotomoulding, high-escr Rotomoulding, high-escr 4.00 ± ± ± ± ± ± HP LLDPE SPECIALTTY PRODUCTS 30Y04 Rotomoutding & Stiff Cast 4.00 ± ± BWMD HDPE for Blow moulding 526F1BX ( * ) 526F2BX 524F2 ( * ) Blow moulding containers, high impact Blow moulding small containers, high ESCR Blow moulding small containers BWMD HDPE for pipes 486H2 ( * ) Pipes 0.2 (1) BWMD HDPE for Blown film 526H1 ( * ) 486H2 ( * ) 524H1FX ( * ) 484H2 ( * ) Blow film, high Stiffness Blow film, high mechanicals Blow film, high Stiffness Blow film, general purposes 0.15 (1) 0.25 (1) 0.15 (1) 0.25 (1) ( * ) Grade under final development, to be Industrialised. (1) Melt Flow rate (190 C/5kg). 42

43 Product data sheet LLDPE made via Spherilene Gas-Phase Technology 22502AA/ 22502KJ is a LLDPE blown film grade designed for applications requiring ease of processing and good optical properties even at low extrusion temperature. This resin is well suited for blending with LDPE and for general purpose uses, including agricultural applications. LLDPE: 22502AA/22502KJ Density: MFI: Characteristic Properties ease of processing good optical properties low extrusion temperature suited for blending with LDPE Main Applications Blown film grade General purpose agricultural applications. Additives 22502AA: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) 22502KJ: Thermal Antioxidant (Process Stabilizer) Antiblocking Agent Slip Agent Catalyst neutralizer (acid scavenger, lubricant) Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 1.80 Density g/ml Film Dart Impact )g( 67 Elmendorf Tear (g) MD/TD 127/332 Tensile strenght at yield (MPa) MD/TD 12/12 Tensile strenght at break (MPa) MD/TD 37/32 Ultimate elongation (%) MD/TD 783/888 Haze (%) 48 Gloss micron film obtained on Collin 25, B.u.R. 2.5: 1, Temp. profile C. Recommended processing conditions Melt Temperature ( C) Blow up ratio Die Gap (mm) Thickness (micron) ASTM Method D1238 D1505 D1709 D1922 D882 D882 D882 D1003 D

44 Product data sheet LLDPE made via Spherilene Gas-Phase Technology 22501AA/ 22501KJ is a LLDPE blown film grade designed for applications requiring good optical properties even at low extrusion temperature. This resin combines ease of processing with low gels and it is well suited for blending with LDPE and for general purpose applications. LLDPE: 22501AA/22501KJ Density: MFI: Characteristic Properties High stiffness good optical properties low extrusion temperature ease of processing low gels suited for blending with LDPE Main Applications Blown film grade General Purpose opplications Additives 22501AA: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) 22501KJ: Thermal Antioxidant (Process Stabilizer) Antiblocking Agent Slip Agent Catalyst neutralizer (acid scavenger, lubricant) Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 0.95 Density g/ml Film Dart Impact )g( 70 Elmendorf Tear (g) MD/TD 105/436 Tensile strenght at yield (MPa) MD/TD 11/12 Tensile strenght at break (MPa) MD/TD 41/31 Ultimate elongation (%) MD/TD 648/780 Haze (%) 48 Gloss micron film obtained on Collin 25, B.u.R. 2.5: 1, Temp. profile C. Recommended processing conditions Melt Temperature ( C) Blow up ratio Die Gap (mm) Thickness (micron) ASTM Method D1238 D1505 D1709 D1922 D882 D882 D882 D1003 D

45 45 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery. - On compression moulded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 45

46 Product data sheet HP-LL18XF5N HP-LLDPE made via Spherilene Gas-Phase Technology HP-LL18XF5 N is a termopolymer of ethylene, propylene and butene-1 for high strenght application especially heavy duty shipping sacks, ice bag, frozen food bags, potato bags and agriculture films which have good sealability and excellent puncture resistance. Goods produced from this grade have outstanding toughness, excellent puncture resistance, good heat sealing behavior and excellent machinability on conversion lines. HP- LLDPE's process is easier than conventional LLDPEs and have low gel. HP- LL18XF5 N is a grade without slip additives. HP-LLDPE: HP-LL18XF5N Density: MFI: Characteristic Properties Main Applications Additives Exellent punctuer resistance. Exellent machinability on conversion lines. T-bags and other bags, Food Packaging for frozen products, Agricultural film, Heat seal film, Food Packaging Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) Antiblocking Agent Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Test Method Melt Index (190 C/ 2.16Kg) )g/10 min( 0.5 D1238 Density Film g/cm³ D1505 Dart Impact g 125 D 1709 Vicat Softening Point C 127 D1525 Tensile Strenght at Yield Mpa (MD/TD) 11/10 D638 Tensile Strenght at Break Mpa (MD/TD) 40/35 D638 Ultimate Elongation % (MD/TD) 600/750 D638 Elmendorf Tear g (MD/TD) 240/400 D1922 Haze % 30 D1003 Gloss on 25 micron film obtained on Collin 25, B.u.R 2.5: 1, Temp. profile C: melt 200 C 46

47 47 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 47

48 Product data sheet HDPE for Monofilament HD-5000S HD 5000S is a HDPE grade specially designed for monofilament applications, which combines good processability with high tenacity. This grade has good balance of mechanical strength and high production rates. HD 5000S is also well suited for multiply applications, like ropes and stretched filaments. Jamlene: HD5000S Typical Applications Fishing net, Rope, Agricultural net, Tarpaulin, Woven sack. Resin Properties Unit Value Test Method Melt Index g/10 min 0.8 D1238 Density g/cm³ D1505 Thermal Properties Unit Value Test Method Vicat Softening Point C 125 D1525 Molded Properties Unit Value Test Method Flectural Modulus Mpa 1100 D790 Tensile Strenght at Yield Mpa 24 D790 Tensile Strenght at Break Mpa 39 D638 H.D.T C 75 D648 Notched Izod 23 C J/m 400 D256/A On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 C and 190 C 48

49 Product data sheet HDPE made via Spherilene Gas-Phase Technology UV is a HDPE injection molding grade which combines high stiffness with good physical properties. This resin is well suited for crates and toys applications. HDPE: 60505/60505UV Density: MFI: Characteristic Properties High stiffness with good physical properties. Main Applications injection molding grade Crates toys applications Additives 60505: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) 60505UV: Catalyst neutralizer (acid scavenger, lubricant) UV Stabilizer Thermal Antioxidant (Process Stabilizer) Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 5.5 Density g/ml Physical Flexural modulus (MPa) 1460 Notched Izod impact at 23 C (J/m) 30 Vicat softening point ( C) on compression moulded specimen obtained according to ASTM D 1928 C Fabrication conditions for injection moulding Recommended barrel temperatures range between 190 and 280 C ASTM Method D1238 D1505 D790 D256/A D

50 Product data sheet HDPE made via Spherilene Gas-Phase Technology HD HD-60507UV is a HDPE homopolymer which is manufactured in gas phase process for injection molding grade which combines good flowability with balanced physical properties. This resin is well suited for general purpose application requiring high stiffness. HDPE: HD-60507/HD-60507UV Density: MFI: Characteristic Properties Good flowability with balanced phisycal properties. Main Applications Crates Injection molding grade Additives HD-60507: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) HD UV: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) UV Stabilizer Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Melt Index (190 C/ 2.16Kg) Density Resin Vicat Softening Point Moulded Flexural Modulus Notched Izod 23 C Unit (g/10 min) g/ml Unit ( C) Unit (MPa) (J/m) Typical Value Typical Value Typical Value Test Method D1238 D1505 Test Method D1525 Test Method D790 D256/A 50

51 Product data sheet HDPE made via Spherilene Gas-Phase Technology UV is a HDPE injection molding grade which combines excellent flowability with high stiffness. This resin is well suited for housewares and toys applications. HDPE: 60511/60511UV Density: MFI: 9-13 Characteristic Properties Excellent flowability with high stiffness. Main Applications injection molding grade Houseware toys Additives 60511: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) 60511UV: Catalyst neutralizer (acid scavenger, lubricant) UV Stabilizer Thermal Antioxidant (Process Stabilizer) Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 11 Density g/ml Physical Flexural modulus (MPa) 1450 Notched Izod impact at 23 C (J/m) 21 Vicat softening point ( C) on compression moulded specimen obtained according to ASTM D 1928 C Fabrication conditions for injection moulding Recommended barrel temperatures range between 190 and 280 C ASTM Method D1238 D1505 D790 D256/A D

52 Product data sheet HDPE for Injection Molding (Caps & Closures) CC52501 CC52501 is a Narrow MWD HDPE specially designed for beverage bottles of sparkling water, hot filled and carbonated soft drinks. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52501 does not contain slip agent. HDPE: CC52501 Typical Applications Caps and closures for beverage bottles of sparkling water, hot filled and carbonated soft drinks. Resin Properties Unit Value Test Method Melt Index g/10 min 0.9 D1238 Density g/cm³ D1505 Thermal Properties Unit Value Test Method Vicat Softening Point C 123 D1525 Molded Properties Unit Value Test Method Flectural Modulus Mpa 800 D790 Tensile Strenght at Yield Mpa 25 D790 Tensile Strenght at Break Mpa 36 D638 H.D.T C 78 D648 Notched Izod 23 C J/m 80 D256/A On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 C and 190 C 52

53 53 Storage and Handling Polyethylene products (in pelletized or powder form) should not be stored in direct sunshine and/or heat radiation. The Storage area should be dry and preferably don t exceed 50 C. JPC would not responsible about quality diminishing such as color change, bad smell or est. which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery Shear 190 C Viscosity (Pa.s) Shear Rate (1/s) The technical information suggested uses and application presented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials. 53

54 Product data sheet HDPE for Injection Molding (Caps & Closures) CC52502 CC52502 is a Narrow MWD HDPE specially designed for mineral water bottles and beverage caps. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52502 does not contain slip agent. HDPE: CC52502 Typical Applications Caps and closures for mineral water bottles,caps for sparkling water and carbonated soft drinks, beverage caps. Resin Properties Unit Value Test Method Melt Index g/10 min 2 D1238 Density g/cm³ D1505 Thermal Properties Unit Value Test Method Vicat Softening Point C 124 D1525 Molded Properties Unit Value Test Method Flectural Modulus Mpa 1000 D790 Tensile Strenght at Yield Mpa 25 D790 Tensile Strenght at Break Mpa 38 D638 H.D.T C 78 D648 Notched Izod 23 C J/m 180 D256/A On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 C and 190 C 54

55 55 Storage and Handling Polyethylene products (in pelletized or powder form) should not be stored in direct sunshine and/or heat radiation. The Storage area should be dry and preferably don t exceed 50 C. JPC would not responsible about quality diminishing such as color change, bad smell or est. which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery Shear 190 C Viscosity (Pa.s) Shear Rate (1/s) The technical information suggested uses and application presented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials. 55

56 Product data sheet HDPE for Injection Molding (Caps & Closures) CC52502SU CC52502 is a Narrow MWD HDPE specially designed for mineral water bottles and beverage caps. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52502SU does contain slip agent and stabilized against UV light. HDPE: CC52501 Typical Applications Caps and closures for mineral water bottles, Caps for sparkling water and carbonated soft drinks, beverage caps. Resin Properties Unit Value Test Method Melt Index g/10 min 2 D1238 Density g/cm³ D1505 Thermal Properties Unit Value Test Method Vicat Softening Point C 124 D1525 Molded Properties Unit Value Test Method Flectural Modulus Mpa 1000 D790 Tensile Strenght at Yield Mpa 25 D790 Tensile Strenght at Break Mpa 38 D638 H.D.T C 78 D648 Notched Izod 23 C J/m 180 D256/A On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 C and 190 C 56

57 57 Storage and Handling Polyethylene products (in pelletized or powder form) should not be stored in direct sunshine and/or heat radiation. The Storage area should be dry and preferably don t exceed 50 C. JPC would not responsible about quality diminishing such as color change, bad smell or est. which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery Shear 190 C Viscosity (Pa.s) Shear Rate (1/s) The technical information suggested uses and application presented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials. 57

58 Product data sheet HDPE made via Spherilene Gas-Phase Technology HD-52505/UV is a HDPE copolymer which is manufactured in gas phase process. This grade is an injection molding grade for applications requiring a good physical property even at low temperatures, like pails, containers and technical moldings. HDPE: 52505/52505UV Density: MFI: 4-6 Characteristic Properties Good physical property even at low temperatures. Main Applications Containers. Additives HD-52505: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) HD UV: Thermal Antioxidant (Process Stabilizer) Antiblocking Agent Catalyst neutralizer (acid scavenger, lubricant) UV Stabilizer Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Melt Index (190 C/ 2.16Kg) Density Thermal Vicat Softening Point Moulded Flexural Modulus Tensile strenght at yield Tensile strenght at break H.D.T Notched Izod 23 C Unit (g/10 min) g/ml Unit ( C) Unit (MPa) (MPa) (MPa) ( C) (J/m) Typical Value Typical Value 124 Typical Value Test Method D1238 D1505 Test Method D1525 Test Method D790 D638 D638 D648 D256/A 58

59 59 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after On compression moulded according to ASTM D1928C Processing Conditions: Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 59

60 Product data sheet HDPE made via Spherilene Gas-Phase Technology UV is a HDPE copolymer injection molding grade for applications requiring a good balance between physical properties and flowability, like housewares and toys. HDPE: 52511/52511UV Density: MFI: 9-13 Characteristic Properties Good balance between physical properties and flowability, Main Applications injection molding grade Houseware Additives 52511: Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) UV: Thermal Antioxidant (Process Stabilizer) Antiblocking Agent Catalyst neutralizer (acid scavenger, lubricant) UV Stabilizer Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 11 Density g/ml Physical Flexural modulus (MPa) 1200 Notched Izod impact at 23 C (J/m) 22 Vicat softening point ( C) on compression moulded specimen obtained according to ASTM D 1928 C Fabrication conditions for injection moulding Recommended barrel temperatures range between 190 and 280 C ASTM Method D1238 D1505 D709 D256/A D

61 61 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after On compression moulded according to ASTM D 1928 C Processing Conditions: Melt Temperature ( C): T190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 61

62 Product data sheet HDPE made via Spherilene Gas-Phase Technology HD is a HDPE copolymer for Injection Moulding for applications requiring a good balance between easy of processability and flowability and mechanical properties. HDPE: HD Density: MFI: Characteristic Properties Main Applications Additives Good balance between easy of processability and flowability Housewares High fluidity Injection moulding grade Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 18 Density g/ml Thermal Unit Typical Value Vicat Softening Point ( C) 121 Moulded Unit Typical Value Flexural Modulus (MPa) 1200 Notched Izod 23 C (J/m) on compression moulded specimen, according to ASTM D 1928 C Test Method D1238 D1505 Test Method D1525 Test Method D790 D256/A 62

63 63 Handling and Health Safety Molten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after On compression moulded according to ASTM D1928C Processing Conditions: Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 63

64 Product data sheet LLDPE made via Spherilene Process LL-32604/UV is a LLDPE for rotomolding which manufactured by gas phase process. This grade is suitable for all applications which need a good balance among moldability and mechanical properties together with an exceptional stress cracking resistance. LLDPE: LL-32604/UV Density: MFI: 4 Features Applications Additives Exellent ESCR. High ESCR rotomolded items Chemical containers. LL-32604: Thermal Antioxidant LL-32604UV: Thermal Antioxidant UV Stabilizer Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Test Method Melt Index g/10 min 4 D1238 Density g/cm³ D1505 Physical Properties Unit Typical Value Test Method Flectural Modulus Mpa 1350 D790 Notched Izod 23 C J/m NB D256/A E.S.C.R h >1000 D

65 65 Handellling and Health Safety smolten polymers could be injured skin or eye so safety glasses and appropriate gloves are suggested to prevent possible thermal injuries. Also appropriate ventilation is suggested in working by melt polymer. Accumulation of fines or dust particles that are in this grade is not suitable because of explosion hazard probability. So adequated filters and grounding exists at all time are recommended. Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.the Storage area should be dry and preferably don't exceed 50 C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month.. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery. - On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range between 190 C and 280 C. 190 C packaging Jam Polymers Polyolefin resins are supplied in pllet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades. The above values were Calculated from data for 100 µm produced on a 75mm Barrnage extruder with 190 C melt temperature using a 2:1 blow ratio and a gap die of 3.0 mm. 65

66 Product data sheet MDPE made via Spherilene Gas-Phase Technology UV MD is a UV stabilized linear medium density polyethylenee grade with a narrow molecular weight distribution. It is suitable for rotational molding and some injection molding application such as technical parts and closures. Characteristics include: good impact strenght, excellent external and internal surface finish, and is UV stabilized. MDPE: UV Density: MFI: 3-5 Characteristic Properties Main Applications Additives Good impact strenght High ESCR Rotomolding Thermal Antioxidant (Process Stabilizer) Catalyst neutralizer (acid scavenger, lubricant) UV Stabilizer Material properties (This data are typical values and are not to be construed as product specifications.) Resin Properties Unit Typical Value Melt Index (190 C/ 2.16Kg) (g/10 min) 4 Density g/ml Physical Flexural Modulus (MPa) 650 Tensile strenght at yield (MPa) 15 Tensile strenght at break (%) 800 Charpy Unnotched impact Strength KJ/m 2 25 Vicat Softening Temperature ( C) 115 Durometer Hardness Shore D on compression moulded specimen obtained according to ASTM D 1928 C ASTM Method D1238 D1505 D790 D638 D638 D256 D1525 D