Announcement No.21 of SELO Notice on Amendment of Conformity Declaration and Comparison Table for Stationary Pressure Vessel To enhance the basic safety requirements of stationary pressure vessel and more convenient for the applicants, SELO amends the Conformity Declaration and Comparison Table for stationary pressure vessel in the Notice for Pressure Special Equipment Manufacture Licensing (AQSIQ Notice No.151 [2012]) <see Appendix>,the Conformity Declaration and Comparison Table for transportable pressure vessel will not change. Please follow below requirements for application and query. 1. Declaration Approach (1) Domestic applicants shall submit the application documents in paper to SELO for review according to Implementation Requirement for TSG 21-2016 Supervision Regulation on Safety Technology for Stationary Pressure Vessel (SESA Notice No.46 [2016]). (2) Oversea Applicants shall submit the application documents online according to Announcement No. 17 of SELO. 2. Query channel (1) Domestic applicants: http://www.selo.org.cn/ (2) Oversea Applicants: http://english.selo.org.cn/ Annex: 1. Conformity Declaration for Pressure Vessel Quality in Conformance with the Essential Safety Requirements 2. Comparison Table for Stationary Pressure Vessel Products and the Essential Safety Requirements of the Supervision Regulations on Safety Technology for Stationary Pressure Vessels (Metal material of Stationary pressure vessel) 3. Comparison Table for Stationary Pressure Vessel Products and the Essential Safety Requirements of the Supervision Regulations on Safety Technology for Stationary Pressure Vessels Non-metal material of Stationary pressure vessel SELO of SAMR Nov.19.2018 Notice This English translation version is for reference only. In case of any discrepancies between English and Chinese version, the Chinese version shall govern.
附件 1 申明单位 Company name 许可证编号 License No. 产品名称 Product name 设计压力 Design pressure 主体尺寸 Body dimension 介质组别 Medium Group 压力容器产品符合质量基本安全要求的申明 Conformity Declaration for Pressure Vessel Quality in Conformance with the Essential Safety Requirements 第一组介质 Group I MPa 第二组介质 Group II 单位地址 Company address 联系人 Contact person 总图号 General drawing No. 设计温度 Design temperature 壳体材料 Shell material 设计制造标准 Design and manufacture standard 电话 & E-mail Telephone & E-mail 压力容器类别 Pressure vessel category 制造许可级别 Manufacture Licensing level 固定式压力容器 : Ⅰ 类 Ⅱ 类 Ⅲ 类 Stationary pressure vessel: Category I Category II Category III 经过与 ( 此处填写产品所适用的压力容器安全技术监察规程的名称 ) 规定的质量基本安全要求的比照, 我公司按 ( 设计制造标准 ) 设计 ( 制造 ) 的 ( 产品名称 ) 符合中国对压力容器的基本安全要求, 特此申明, 详细比照结果见 压力容器产品与 **** 压力容器安全技术监察规程 质量基本安全要求比照表, 并承诺对本申明的真实性负责 After comparing with the pressure vessel essential safety quality requirements of (please fill in here the name of the applicable pressure vessel safety technical supervision regulation), we hereby declare the (product name) products that we designed/manufactured in accordance with (_design/manufacture standards) conform to the essential safety requirements. Please refer to the attached Comparison Table for Pressure Vessel Products and the Essential Safety Requirements of the Supervision Regulations on Safety Technology for ****Pressure Vessels for the comparison results; we commit ourselves to be responsible for the authenticity of the declaration. 责任人 ( 签字 ): 年月日 Responsible person(signature): Year Month Date ( 本栏由国家市场监督管理总局特种设备许可办公室填写 ) (This column shall be filled by SELO of State Administration for Market Regulation) 编号 : Serial No.:
Metallic Material Requirements 金属材料技术要求 序号 NO. 附件 2 固定式压力容器产品与 固定式压力容器安全技术监察规程 质量基本安全要求比照表 ( 金属材料固定式压力容器 ) Comparison Table for Stationary Pressure Vessel Products and the Essential Safety Requirements of the Supervision Regulations on Safety Technology for Stationary Pressure Vessels (Metal material stationary pressure vessel) 中国基本安全要求 Basic safety quality requirements of china 产品采用的非中国标准要求 Adopted code requirements 产品实际情况 Products practical situation 符合性申明 Conformity declaration 备注 ( 处置情况 ) Note (Disposition) 1 2 固容规 2.2.1.2 化学成分 ( 熔炼分析 ) (Regulations 2.2.1.2) Chemical composition (heat analysis) 固容规 2.2.1.3 力学性能 (Regulations 2.2.1.3) Mechanical properties C %,S %,P % 冲击吸收能量 ( KV 2 ) = Impact energy(kv 2 )= 断后伸长率 (A)= Elongation after fracture(a)= 材料标准 : Material standards: 材料牌号 : Material designation: C %,S %,P % 冲击功吸收能量 (KV 2 )= Impact energy(kv 2 )= 断后伸长率 (A)= Elongation after fracture(a)= 注意其他受压元件材料 Pay attention to other pressure parts material 注意其他受压元件材料 Pay attention to other pressure parts material
3 4 5 固容规 2.2.1.4 钢板超声检测 (Regulations 2.2.1.4) Ultrasonic test (UT) for steel plates 固容规 2.2.1.5.1 化学成分 ( 熔炼分析 ) (Regulations 2.2.1.5.1) Chemical composition (heat analysis) 固容规 2.2.1.5.2 力学性能 (Regulations 2.2.1.5.2) Mechanical properties 按比例 100% 进行 Require 100% 按其他比例进行 : Require other percentage: 无要求 Not required 按比例 100% 进行 Require 100% 按其他比例进行 : Require other percentage: 不需要 Not required 固容规 2.2.1.5 超高压容器用钢专项要求 (Regulations 2.2.1.5) Special requirements of steels used for ultra-high pressure vessels Disposition 固容规 2.2.1.6 非焊接瓶式容器用钢专项要求 (Regulations 2.2.1.6) Special requirements of steels used for non-welded cylinder type vessels
6 7 8 9 固容规 2.2.1.6.1.1 冶炼和热处理 (Regulations 2.2.1.6.1.1) Smelting and heat treatment 固容规 2.2.1.6.1.2 化学成分和力学性能 (Regulations 2.2.1.6.1.2) Chemical composition and mechanical properties 固容规 2.2.1.6.1.3 超声检测 (Regulations 2.2.1.6.1.3) Ultrasonic test 固容规 2.2.1.6.2 端塞用钢材 (Regulations 2.2.1.6.2) Steel material of the end plug 固容规 2.2.1.8 简单压力容器用钢专项要求 (Regulations 2.2.1.8) Special requirements of steels used for simple pressure vessels
10 11 12 固容规 2.2.1.8 简单压力容器用钢专项要求 (Regulations 2.2.1.8) Special requirements of steels used for simple pressure vessels 固容规 2.2.2 复合钢板专项要求 (Regulations 2.2.2) Special requirements of clad steel plates 固容规 2.2.3.1 铸铁材料的使用限制 (Regulations 2.2.3.1) Application limitation for cast irons 材料牌号 : Material designation: 使用状态 : Operation situation: 固容规 2.2.2 复合钢板专项要求 (Regulations 2.2.2) Special requirements of clad steel plates 固容规 2.2.3 铸铁容器技术要求 (Regulations 2.2.3) Technical requirements of cast iron vessels 材料牌号 : Material designation: 使用状态 : Operation situation:
13 14 15 16 固容规 2.2.3.2 铸铁容器设计压力 温度限制 (Regulations 2.2.3.2) Limitation of design pressure and design temperature of cast iron vessels 固容规 2.2.4.1 铸钢材料的使用限制 (Regulations 2.2.4.1) Application limitation for cast steels 固容规 2.2.4.2 铸钢材料的冶炼和化学成分 (Regulations 2.2.4.2) Smelting and chemical composition of cast steels 固容规 2.2.4.3 铸钢材料的性能 (Regulations 2.2.4.3) Mechanical properties of cast steels 设计温度限制 : Design temp limit: 设计压力限制 : MPa Design pressure limit: MPa 使用状态 : Operation situation: C %,S %,P % 设计温度限制 : Design temp limit: 设计压力限制 : MPa Design pressure limit: MPa 固容规 2.2.4 铸钢容器技术要求 (Regulations 2.2.4) Technical requirements of cast steel vessels 使用状态 : Operation situation: 材料标准 : Shell material standards: 材料牌号 : Shell material designation: C %,S %,P %
17 18 19 20 固容规 2.2.4.4 铸钢容器设计压力 温度限制 (Regulations 2.2.4.4) Limitation of design pressure and design temperature of cast steel vessels 固容规 2.2.5.1 通用要求 (Regulations 2.2.5.1) General requirement 固容规 2.2.5.2 铝和铝合金容器 (Regulations 2.2.5.2) Aluminum and aluminum alloy vessels 固容规 2.2.5.3 铜和铜合金容器 (Regulations 2.2.5.3) Copper and copper alloy vessels 设计温度限制 : Design temp limit: 设计压力限制 : MPa Design pressure limit: MPa 设计温度限制 : Design temp limit: 设计压力限制 : MPa Design pressure limit: MPa 固容规 2.2.5 有色金属容器技术要求 (Regulations 2.2.5) Technical requirements of nonferrous pressure vessels
uire men ts 21 22 23 固容规 2.2.5.4 钛和钛合金容器 (Regulations 2.2.5.4) Titanium and titanium alloy vessels 固容规 2.2.5.5 镍和镍合金容器 (Regulations 2.2.5.5) Nickel and nickel alloys vessels 固容规 2.2.5.6 钽 锆 铌及其合金容器 (Regulations 2.2.5.6) Tantalum, zirconium, niobium and their alloys vessels 固容规 3.1 设计通用要求 (Regulations 3.1) General Requirements
24 25 26 固容规 3.1.5 设计方法 (Regulations 3.1.5) Design method 固容规 3.1.8 设计载荷 (Regulations 3.1.8) Design load 固容规 3.1.5 3.1.6 失效模式 (Regulations 3.1.5, 3.1.6) Failure mode 压力 Pressure 重力载荷 Gravitational load 外部作用力 External acting force 温差载荷 TEMP difference load 风载荷 Wind load 地震载荷 Earthquake load 雪载荷 Snow load 其他载荷 Other load 脆性断裂 (1) Brittle fracture(1) 韧性断裂 (2) Ductile rupture(2) 蠕变断裂 (3) Creep rupture(3) 弹性或塑性失稳 (4) Elastic or plastic instability(4) 接头泄露 (5) Nozzle leakage(5) 其他 : (6) Others: (6) 规则设计方法 Design by rules 分析设计方法 Design by analysis 试验设计方法 Design by experimental method 可对比经验设计方法 Design by empirical method 其他设计方法 Other method 技术评审 Technical review 压力 Pressure 重力载荷 Gravitational load 外部作用力 External acting force 温差载荷 TEMP difference load 风载荷 Wind load 地震载荷 Earthquake load 雪载荷 Snow load 其他载荷 Other load 可能的失效模式 : Possible failure mode: 风险评估报告 : Risk analysis report: 需要 不需要 Required Not required 固容规 3.2 金属压力容器设计要求 (Regulations 3.2) Design requirements for metallic pressure vessels 采用试验方法 可对比的经验设计方法 其他设计方法应通过技术评审 Design by experimental method, empirical method and Other method shall be subject to technical review by the third party designated by State Administration for Market Regulation 对第 Ⅲ 类压力容器 应出具风险评估报 告 For category III pressure vessel, the risk evaluation report shall be issued
27 28 29 30 固容规 3.2.1.1 安全系数 (Regulations 3.2.1.1) Safety factor 固容规 3.2.14.1 设计方法 (Regulations 3.2.14.1) Design methods 固容规 3.2.14.2 安全系数 (Regulations 3.2.14.2) Safety factor 固容规 3.2.15.2 设计方法 (Regulations 3.2.15.2) Design methods n b n d n b n b irons) n b n s n b n n n d ( 灰铸铁 )(grey cast irons) n b ( 球墨铸铁 )(nodular cast n b irons) ( 铸钢 )(cast steels) n b n s n n ( 灰铸铁 )(grey cast irons) ( 球墨铸铁 )(nodular cast ( 铸钢 )(cast steels) 固容规 3.2.14 超高压容器设计专项要求 (Regulations 3.2.14) Special requirements for the design of ultra-high pressure vessels 爆破压力法的安全系数 : Safety factor of burst pressure calculation method: 疲劳分析的安全系数 : Safety factor of fatigue analysis: 螺柱 ( 螺栓 ) 的安全系数 : Safety factor of the stud (bolt): 最小壁厚 : Minimum wall thickness 爆破压力法 burst pressure calculation method 弹塑性分析法 elastic plastic analysis 爆破压力法的安全系数 : Safety factor of burst pressure calculation method: 疲劳分析的安全系数 : Safety factor of fatigue analysis: 螺柱 ( 螺栓 ) 的安全系数 : Safety factor of the stud (bolt): 固容规 3.2.15 简单压力容器设计专项要求 (Regulations 3.2.15) Special requirements for the design of simple pressure vessels 主要受压元件的壁厚采用 : The wall thickness of main pressure components is determined by: 试验方法 testing method 计算方法 calculating method
Requirements for fabrication of mental pressure vessels 金属压力容器制造要求 31 32 33 固容规 3.2.16 (Regulations 3.2.16) 固容规 4.2.2 试件 ( 板 ) 与试样 (Regulations 4.2.2) Test coupon (plate) and specimen 固容规 3.2.10 4.2.5 无损检测 (Regulations 3.2.10, 4.2.5) Non-destructive testing (NDT) 最小壁厚 : Minimum wall thickness: 固容规 3.2.16 快开门式压力容器设计专项要求 (Regulations 3.2.16) Special requirements for the design of quick opening pressure vessels 当快开门达到预定关闭部位, 方能升压运行 When the quick opening device reaches the preset closure position, pressure can be raised for operation 内部压力完全释放, 方能打开快开门 Only after the internal pressure is completely released, the quick opening device can be opened 安全联锁功能 : Safety interlock function: 焊接试件 : 要求 不要求 Welding coupon: Required Not required 母材热处理试件 : 要求 不要求 Base metal heat treatment specimen: Required Not required 方法及比例 : Method and percentage: 焊接试件 : 有 无 Welding coupon: Available Not available 母材热处理试件 : 有 无 Base metal heat treatment specimen: Available Not available RT 比例 : RT percentage: UT 比例 : UT percentage: MT 比例 : MT percentage: PT 比例 : PT percentage:
34 35 36 37 固容规 3.2.11 4.2.6 热处理 (Regulations 3.2.11, 4.2.6) Heat treatment 固容规 3.2.12 4.1.9 耐压试验 (Regulations 3.2.12, 4.1.9) Pressure testing 固容规 3.2.13 4.1.10 泄漏试验 (Regulations 3.2.13, 4.1.10) Leakage test 固容规 4.2.7.1 锻焊式压力容器 (Regulations 4.2.7.1) Forged-welded pressure vessels 焊后热处理 : Postweld heat treatment 方法 : Method: 压力系数 : Pressure coefficient: 方法 : Method: 气密性试验 Air-tight test 氨检漏试验 Ammonia leak test 卤素检漏试验 Halogen leak test 氦检漏试验 Helium leak test 其他 : Others 不需要 Not required 热处理工艺 Heat treatment process 液压试验压力系数 : Hydraulic test pressure coefficient: 气压试验压力系数 : Air pressure test pressure coefficient: 气液组合试验压力系数 : The gas-liquid combined test pressure coefficient: 气密性试验 Air-tight test 氨检漏试验 Ammonia leak test 卤素检漏试验 Halogen leak test 氦检漏试验 Helium leak test 其他 : Others 固容规 4.2.7 锻钢 铸铁 不锈钢与有色金属制压力容器的专项要求 (Regulations 4.2.7) Special requirements for pressure vessels of steel forgings, cast irons, stainless steels and non-ferrous metals
38 39 40 41 固容规 4.2.7.2 铸造压力容器 (Regulations 4.2.7.2) Cast iron pressure vessels 固容规 4.2.7.3 不锈钢和有色金属制压力容器 (Regulations 4.2.7.3) Stainless steel and non-ferrous metallic pressure vessels 固容规 4.2.7.4 有色金属制压力容器 (Regulations 4.2.7.4) Non-ferrous metallic pressure vessels 固容规 4.2.8.2.2 无损检测的实施时机 (Regulations 4.2.8.2.2) The timing for performing NDT 固容规 4.2.8 超高压容器制造专项要求 (Regulations 4.2.8) Special requirements for fabrication of super-high pressure vessels
42 43 44 45 固容规 4.2.9.4 爆破试验 (Regulations 4.2.9.4) Bursting test 固容规 4.2.9.5 无损检测 (Regulations 4.2.9.5) NDT 固容规 4.2.9.6 型式试验 (Regulations 4.2.9.6) Type test 需要强调说明的问题 : Other issues need to be emphasized and specified: 固容规 4.2.9 简单压力容器制造专项要求 (Regulations 4.2.9) Special requirements for the fabrication of simple pressure vessels 注 : 固容规 指 TSG 21-2016 固定式压力容器安全监察规程 Regulations refers to the Supervision Regulations on Safety Technology for Stationary Pressure Vessels( TSG 21-2016)
Technical requirements of non-metallic materials 非金属材料技术要求 附件 3 固定式压力容器产品与 固定式压力容器安全技术监察规程 质量基本安全要求比照表 ( 非金属材料固定式压力容器 ) Comparison Table for Stationary Pressure Vessel Products and the Essential Safety Requirements of the Supervision Regulations on Safety Technology for Stationary Pressure Vessels Non-metal material stationary pressure vessel 序号 N O. 1 2 中国基本安全要求 Basic safety quality requirements of china 固容规 2.3.1.1 石墨材料的一般要求 (Regulations 2.3.1.1) General requirements of graphite materials 固容规 2.3.1.2 石墨材料的性能要求 (Regulations 2.3.1.2) Requirements of graphite material properties 产品采用的非中国标准要求 Adopted code requirements 产品实际情况 Products practical situation 固容规 2.3.1 石墨压力容器材料 (Regulations 2.3.1) Graphite pressure vessels 符合性申明 Conformity declaration after after 备注 ( 处置情况 ) Note (Disposition)
3 4 5 6 固容规 2.3.1.3 粘结剂要求 (Regulations 2.3.1.3) Requirements of adhesives 固容规 2.3.2.1 纤维增强材料 (Regulations 2.3.2.1) Fiber reinforcement materials 固容规 2.3.2.2 树脂基体 (Regulations 2.3.2.2) Resin matrix 固容规 2.3.2.3 粘结材料性能要求 (Regulations 2.3.2.3) Properties of adhesive materials 固容规 2.3.2 纤维增强塑料压力容器材料 (Regulations 2.3.2) Fiber reinforced plastic pressure vessels after after after after
Design Requirements 设计要求 7 8 9 固容规 2.3.2.4 热塑性塑料衬里 (Regulations 2.3.2.4) Thermoplastic lining 固容规 3.1.5 设计方法 Design Requirements 固容规 3.1.8 设计载荷 (Regulations 3.1.8) Design load 压力 Pressure 重力载荷 Gravitational load 外部作用力 External acting force 温差载荷 TEMP difference load 风载荷 Wind load 地震载荷 Wind load 雪载荷 Snow load 其他载荷 Other load 固容规 3.1 设计通用要求 (Regulations 3.1) General Requirements 规则设计方法 Design by rules 分析设计方法 Design by analysis 试验设计方法 Design by experimental method 可对比经验设计方法 Design by empirical method 其他设计方法 Other method 技术评审 Technical review 压力 Pressure 重力载荷 Gravitational load 外部作用力 External acting force 温差载荷 TEMP difference load 风载荷 Wind load 地震载荷 Wind load 雪载荷 Snow load 其他载荷 Other load after after after 采用试验方法 可对比的经验设计方法 其他设计方法应通过技术评审 Design by experimental method, empirical method and Other method shall be subject to technical review by the third party designated by State Administration for Market Regulation
10 11 12 13 固容规 3.1.5 3.1.6 失效模式 (Regulations 3.1.5, 3.1.6) Failure mode 固容规 3.3.1.1 设计范围 (Regulations 3.3.1.1) Design scope 固容规 3.3.1.2 安全系数和许用应力 (Regulations 3.3.1.2) Safety factor and allowable stress 固容规 3.3.2.1 通用要求 (Regulations 3.3.2.1) General requirements 脆性断裂 (1) Brittle fracture(1) 韧性断裂 (2) Ductile rupture(2) 蠕变断裂 (3) Creep rupture(3) 弹性或塑性失稳 (4) Elastic or plastic instability(4) 接头泄露 (5) Nozzle leakage(5) 其他 : (6) Others: (6) 可能的失效模式 : Possible failure mode 风险评估报告 : 需要 不需要 Risk analysis report Required Not required 固容规 3.3 非金属压力容器设计要求 (Regulations 3.3) Design requirements of nonmetallic pressure vessels (1) 最大设计外压 : (1)Maximum design external pressure (2) 最大设计内压 : (2)Maximum design internal pressure (3) 最低设计温度 : (3)Lowest design temperature (4) 最高设计温度 : (4)Highest design temperature 许用应力 : allowable stress value: 安全系数 : allowable stress value: (1) 最大设计外压 : (1)Maximum design external pressure (2) 最大设计内压 : (2)Maximum design internal pressure (3) 最低设计温度 : (3)Lowest design temperature (4) 最高设计温度 : (4)Highest design temperature 许用应力 : allowable stress value: 安全系数 : allowable stress value: 固容规 3.3.2 纤维增强塑料压力容器 (Regulations 3.3.2) Fiber reinforced plastic pressure vessels after after after after 对第 Ⅲ 类压力容器应出具风险评估报告 For category III pressure vessel, the risk evaluation report shall be issued
Requirements for fabrication of nonmetallic pressure vessels 非金属压力容器制造要求 14 15 16 17 固容规 3.3.2.2 设计类型 (Regulations 3.3.2.2) Design types 固容规 3.3.2.3 设计方法及安全系数 (Regulations 3.3.2.3) Design methods and safety factor 固容规 4.3.1 石墨压力容器制造专项要求 (Regulations 4.3.1) Special requirements for fabrication of graphite pressure vessels 固容规 4.3.2 纤维增强塑料压力容器制造专项要求 (Regulations 4.3.2) Special requirements for fabrication of fiber reinforced plastic pressure vessels after after after after
Others 其他 18 19 固容规 4.3.3 非金属压力容器中的金属受压元件的制造 (Regulations 4.3.3) Special requirements for fabrication of fiber reinforced plastic pressure vessels 以上未列出的条款 Other items not listed above 需要强调说明的问题 : Other issues need to be emphasized and specified: after after 20 注 : 固容规 指 TSG 21-2016 固定式压力容器安全监察规程 Regulations refers to the Supervision Regulations on Safety Technology for Stationary Pressure Vessels( TSG 21-2016)