Unit 10 Victory Park Victory Road Derby Derbyshire DE24 8ZF ontact: Mr G Tomlinson Tel: +44 (0)1332 275700 Fax: +44 (0)1332 275729 E-Mail: graham.tomlinson@ndtservices.co.uk Website: www.ndtservices.co.uk Laboratory locations: below s covered by the organisation and their relevant activities details ctivity code ddress Unit 10 Victory Park Victory Road Derby Derbyshire DE24 8ZF Local contact Mr Graham Tomlinson Tel: +44 (0)1332 275700 Fax: +44 (0)1332 275729 E-Mail: graham.tomlinson@ndtservices.co.uk Metals & Weldments - oatings Metals & Weldments - orrosion tests Metals & Weldments - Mechanical tests Metals & Weldments - Metallurgical tests Metals & Weldments - NDT tests ddress Unit No 5 Victory House 99 Victory Road Derby DE24 8EL Local contact Mr Ian opestake Tel: +44 (0)1332 275820 Fax: +44 (0)1332 275817 E-Mail: ian.copestake@ndtservices.co.uk Metals & Weldments - hemical tests Metals & Weldments - orrosion tests Metals & Weldments - Mechanical tests Metals & Weldments - Metallurgical tests Metals & Weldments - NDT tests Site activities performed away from the locations listed above: details ctivity code ddress ny suitable customer premises Local contact Mr. Graham Tomlinson Tel: +44 (0)1332 275700 Fax: +44 (0)1332 275729 E-Mail: graham.tomlinson@ndtservices.co.uk Metals & Weldments - NDT tests ssessment Manager: 1 Page 1 of 8
DETIL OF REDITTION METLS, LLOYS and METL PRODUTS hemical Tests ast Iron Elemental nalysis, Si, Mn, P, S, r, Mo, Ni, l, u,, o, Pb, Ti, V, Nb, W, Sn, Mg, s Low and High alloy steels Elemental nalysis, Si, Mn, P, S, r, Mo, Ni, l, u,, o, Pb, Ti, V, Nb, W, Sn Stainless Steel Elemental nalysis, Si, Mn, P, S, r, Mo, Ni, l, u,, o, Pb, Ti, V, Nb, W, Sn luminium and luminium alloys Elemental nalysis u, Si, Mn, r, Ni, l, Pb, Mg, o, Fe, Sb, Sn, Ti, Zn, Zr opper and opper alloys Elemental nalysis Si, Mn, P, S, Ni, l, s, u, Pb, Sn, Zn, Fe orrosion Tests ustenitic stainless steels, Intergranular attack STM G28-02(08) Practices & Wrought, nickel and chromium bearing alloys Intergranular attack S EN ISO 3651-2:1998 Method, & STM 262-15 Practices,,, E & F Stainless steels Pitting resistance STM G48-11 Method Metal products, forging and castings Physical tests Surface roughness S 1134-1:1988 Documented In-House Method MP 049 ssessment Manager: 1 Page 2 of 8
METLS, LLOYS and METL PRODUTS (cont d) Mechanical Tests end S EN ISO 7438:2016 STM E290-14 Hardness: Portable (comparative) Vickers HV30 and HV10 HV0.2 and HV0.5 Documented In-House Method MP 09 using Equotip equipment S EN ISO 6507-1:2005 rinell S EN ISO 6506-1:2014 Rockwell ( and Scales) S EN ISO 6508-1:2016 Tensile: Tensile (ambient temperature) (Force from 0.4kN to 1000kN) Tensile (elevated temperature) (Force from 6kN to 50kN) (T = ambient to 600 ) Impact: harpy (V-notch) (Temperatures -196 and - 80 to ambient) S EN ISO 6892-1:2016 S EN 2002-1:2005 S 44:Part 1:Section 1:1966 STM 370-16 STM E8/E8M-16a S EN ISO 6892-2:2011 STM E21-09 S EN ISO 148-1:2010 STM E23-16b Izod S 131-1:1961 Lateral expansion and percent shear S EN ISO 148-1:2010 STM E23-16b Metallurgical Tests Volume fraction STM E562-11 ase depth S 6286:1982(2005) S 6479:1984(1990) (withdrawn) S EN 10328:2005 S EN ISO 2639:2002 ssessment of microstructures Documented in-house Method MP 80 ssessment Manager: 1 Page 3 of 8
LIGHT and DENSE METLS and LLOYS including casting, forging & weldments Non Destructive Testing Eddy urrent Flaw Detection: Manual scanning equipment utomatic scanning equipment S EN 1971-1:2011 S EN 1971-2:2011 S EN ISO 10893-1:2011 S EN ISO 15549:2010 Liquid Penetrant: olour contrast - manual application Fluorescent - immersion line (Site ) S M 39:1972 S EN ISO 3452-1:2013 S EN ISO 3452-2:2013 S EN ISO 3452-3:2013 S EN ISO 3452-4:1999 S EN ISO 3452-5:2008 S EN ISO 3452-6:2008 STM E165-12 STM E1417-16 RRP 58003:Issue F WS D17.1/D17.1M:2010 md1:2012, Radiography: X-Ray (15 kev to 320 kev - Site ) (50 kev to 225 kev - Site ) S EN ISO 5579:2013 S EN ISO 17636-1:2013 S EN ISO 17636-2:2013 RRP 58006:Issue D S ISO 24394:2008+1:2012 WS D17.1/D17.1M:2010 md1:2012, ssessment Manager: 1 Page 4 of 8
LIGHT and DENSE METLS and LLOYS including casting, forging & weldments (cont d) Non Destructive Testing (cont d) Gamma-Ray Ir 192 up to 740 Gq (20 i) Se 75 up to 80 curies Ytb 169 up to 10 curies S M 34:1970(1984) S EN ISO 5579:2013 S EN ISO 17636-1:2013 S EN ISO 17636-2:2013 STM E94-10 STM E1742-12 MS 2175 Rev DIN 54111:Part 1:1988 MIL-STD453(1984) (Superseded) MIL-STD 2175(1984) (Superseded) RRP 58006:Issue D S ISO 24394:2008+1:2012 WS D17.1/D17.1M:2010 md1:2012, Ultrasonic Flaw Detection: utomated examination method S EN 10160:1999 S EN ISO 17640:2010 MS-STD-2154 Rev Immersion method S M 36:1970(1984) MS-STD-2154 Rev RRP 58001:Issue Manual contact method S EN 10160:1999 S EN 10228-3:1998 S EN ISO 17640:2010 MS-STD-2154 Rev RRP 58002:Issue, ssessment Manager: 1 Page 5 of 8
LIGHT and DENSE METLS and LLOYS including castings, forgings and weldments, aerospace structures and components Eddy urrent Flaw Detection S EN ISO 10893-1:2011 S EN ISO 10893-2:2011 S EN ISO 15549:2010 ircraft manufacturers recommended in-service inspection techniques Liquid Penetrant: olour contrast - manual application Fluorescent - manual application S M 39:1972 S EN ISO 3452-1:2013 STM E165-12 STM E1417-16 ircraft manufacturers recommended in-service inspection techniques FEROMGNETI METLS Magnetic Particle: lack ink - universal and portable kit Fluorescent ink - universal and portable kit ( and D up to 3000 ) S 6072:1981(1986) S EN 17638:2009 S EN ISO 9934-1:2015 STM E1444-/E1444M-16 MIL-STD 1949(1985) (Superseded), RRP 58004:Issue F S ISO 24394:2008+1:2012 WS D17.1/D17.1M:2010 md1:2012 ircraft manufacturers recommended in-service inspection techniques Magnetic particle: urrent flow method (up to 800 - & D) Magnetic flow method Magnetic yoke method S 6072:1981(1986) S EN 10228-1:1999 S EN ISO 9934-1:2015 S EN 17638:2009 STM E709-15 ssessment Manager: 1 Page 6 of 8
FEROMGNETI METLS (cont d) Magnetic particle: Magnetic flow method Magnetic yoke method Portable equipment S 6072:1981 (1986) S EN 10228-1:1999 S EN ISO 9934-1:2015 S EN 17638:2009 STM E709-15 METLS, LLOYS and METL PRODUTS WELDMENTS Mechanical, Metallurgical and Non Destructive Tests Tests designated in specified welding codes as detailed below: end, Fracture, Hardness, Tensile, Liquid Penetrant, Magnetic Particle, Macro- and Micro-examination, Radiography, Ultrasonic and Visual Examination in accordance with specific welding codes S 1140:1993 S 4872:Part 1:1982(1999) S 4872:Part 2:1976(1999) S EN 287-1:2011 S EN ISO 9606-1:2013 S EN ISO 15609-1:2004 S EN ISO 15613:2004 S EN ISO 15614-1:2004+2:2012 S EN ISO 15614-2:2005 S EN ISO 15614-3:2008 S EN ISO 15614-5:2004 S EN ISO 15614-6:2006 S EN ISO 15614-7:2016 S EN ISO 15614-8:2002 S EN ISO 9017:2013 S EN ISO17639:2013 S EN ISO 4136:2012 S EN ISO 5173+1:2011 S EN ISO 5178:2011 S EN ISO 9015-1:2011 S EN ISO 9016:2011 S EN ISO 9606-2:2004 S EN ISO 17637:2011 SME IX:2015 R 8-10 RPS 912 (Section 2.6 only) PD 5500:2015 S ISO 24394:2008+1:2012 WS D17.1/D17.1M:2010 md1:2012, * ssessment Manager: 1 Page 7 of 8
* NDT techniques not specific to any site - contact laboratory for further details. END ssessment Manager: 1 Page 8 of 8