Agruline Piping Systems for Gas application en
Worldwide competence in plastics AGRU Kunststofftechnik GmbH is an Austrian company. AGRU proves its competence and innovation in the development and production of high-quality products which are made of thermoplastic polymers, for almost 50 years. The product group AGRULINE offers a complete and first-class range of pipes, fittings, valves and special parts made of polyethylene for the environmentally friendly and safe supply of natural gas. The most modern machinery and well trained special staff ensure production of highest grade products. PE piping systems Application areas and benefits Agruline has a broad product range of high quality PE 100 / PE 100 RC products for gas applications. Pipes, fittings, valves and special parts are especially suitable for this applications. Due to the excellent weldability different joining technologies are applicable, e.g. heating element butt - or electrofusion welding. All PE 100 pipes and fittings are made of materials that are listed at the PE 100+ association.
Benefits of PE 100 z100 % leak tight piping system, also at seismic activities or ground movement zmaintenance free characteristics and extended durability zno desposits and no overgrowth possible zcost saving because of low weight zflexible installation on site zexpected lifetime >100 years for natural gas supply PE 100 pipes Agru PE 100 pipes are produced as standard 5 m - 12 m or coiled bundles according EN 1555 standard for gas. OD 20 mm - OD 225 mm Sureline Pipes (PE 100 RC) These pipes are suitable and highly recommended for alternative installation methods. Sureline pipes are co-extruded solid wall pipes with a dimensionally integrated orange coloured signal layer or black with orange stripes for gas applications. Due to the use of high-grade PE 100 RC materials they offer an optimum protection against point loads, crack initiation, slow crack growth and damages on the outside. SDR 17 OD 75 mm - OD 630 mm SDR 11 OD 32 mm - OD 630 mm
SureFIT Surefit liners are factory pre-formed PE-pipes that are used for relining of e.g. concrete, steel, cast iron, stoneware or PVC pipes without annular space. For natural gas SDR 17 DN 125 mm - DN 400 mm For every application... SDR 17 OD 63 mm - OD 500 mm* SDR 11 OD 20 mm - OD 500 mm* * Stub flanges up to OD 630 mm Fittings with long spigots Elongated PE 100 fittings are suitable for electrofusion, as well as heating element butt welding.
Fittings with short spigots PE 100 Fittings with short spigots can be installed by heating element butt welding. SDR 33 OD 110 mm - OD 500 mm* SDR 17 OD 63 mm - OD 500 mm* SDR 11 OD 20 mm - OD 500 mm * * Stub flanges up to OD 710 mm... the pipe with matching features Electrofusion fittings In order to get permanently leak-proof material connections between pipes and fittings, the electrofusion technology has proven to be an alternative solution to other welding technologies. These piping systems for gas supply has been successfully used for many years. Advantages: zprocessable from -10 C up to +45 C zvery good pipe guidance due to long insertion depths zentirely embedded resistance wire zeasy to clean zresistance wire is protected against damages, corrosion and contamination zcontrolled heat transfer E-fittings SDR 11 OD 20 mm - 225 mm E-couplers injection moulded SDR 17 OD 90 mm - 500 mm SDR 11 OD 20 mm - 500 mm
Tapping saddle Tapping saddles are produced in a similar way to electrofusion fittings. They are made with an entirely embedded resistance wire in a fully automated injection moulding. SDR 11 OD 63/20 mm - OD 225/63 mm The patented telescope unit enables gas-tight tapping under pressure (10 bars). A leak test of the finished house connection is possible through the tapping system. Tapping saddles are also available with additional gas stop as safety for gas supply lines in case of damage of the service connection line (e.g. excavator) Broad range... 60, 45, 30, 22, 11 Sweep bends Sweep bends are permanent inherently-stabile high-grade bends made of PE pipes that fulfil today s requirements.they are suitable for heating element butt and electrofusion welding. SDR 17 OD 90 mm - OD 315 mm SDR 11 OD 90 mm - OD 315 mm Further dimensions on request
Ball valves The PE 100 ball valve is a unique and innovative solution for gas. It s stabile construction offers exceptional advantages compared to common systems. Without gearbox SDR 11 OD 32 mm - OD 125 mm With gearbox SDR 11 OD 63 mm - OD 225 mm... of fittings All PE 100 pipes and fittings are produced according the gas standards EN 1555 and ISO 4437 Certificates for gas zövgw zdvgw zsvgw ziip zcertigaz (Gaz de france) ztüv References EVN, RWE, BEGAS, OÖ Ferngas, VEG, SBL Linz, Wr. Stadtwerke, GFB, VEG, Innsbrucker Stadtwerke, BMW, SBL Linz, OÖ Ferngas, Electrabel, Comgas, Gas Natural, INA Naftaplin, Komualac - Konjscina Water company, Natural Gas, Gaz de France, British Gas, Südwestgas AG, Rhenag, Thüga, Maingas, Pfalz-Gas, Landesgas, Erdgas, VEW, E.ON, Mitsubishi Electric, Japan Rail, Interchem, Gasprom, Siemens, Rabmer, GASAG Berlin, Sonelgaz
en Trenchless rehabilitation with the SureFIT / r.tec close-fit-liner suitable for natural gas, potable water, sewage and industrial pipelines SureFIT r.tec CLOSE-FIT-LINER zfast & easy zsustainable & environmentally friendly zlong-lasting (+100 years) zdn 125 mm up to DN 400 mm z agruline Piping systems for natural gas, water & sewage Y20501021213 3 F Subject to errors of typesetting, misprints and modifications. Illustrations are generic and for reference only. Your distributor: AGRU Kunststofftechnik GmbH Ing.-Pesendorfer-Straße 31 A - 4540 Bad Hall T +43 (0) 7258 790-0 F +43 (0) 7258 3863 office@agru.at www.agru.at