2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Hareness Circle Industrial Estate Aberdeen Scotland AB12 3LY Contact: Mrs D McAdam Tel: +44 (0)1224-890020 Fax: +44 (0)1224-890220 E-Mail: info.aberdeen@element.com Website: www.element.com below Laboratory locations: s covered by the organisation and their relevant activities details Activity Address Hareness Circle Industrial Estate Aberdeen Scotland AB12 3LY Local contact Mrs D McAdam Tel: +44 (0)1224-890020 Fax: +44 (0)1224-890220 Email : info.aberdeen@element.com Metals & Weldments - Chemical tests Metals & Weldments - Corrosion tests Metals & Weldments - Mechanical tests Metals & Weldments - Metallurgical tests Site activities performed away from the locations listed above: details Activity Commercial and industrial premises and sites Metals & Weldments Metallurgical Tests Metals & Weldments - Positive Material Identification C&I Assessment Manager: NC2 Page 1 of 5
DETAIL OF ACCREDITATION Mechanical Tests Fracture toughness K1C Jcritical J0.2BL J1C CTOD R-Curve T0 BS 7448:Part 1:1991 BS7448-4:1997 inc Corr1 BS EN ISO 15653:2010 ISO 12135:2016 DNV OS F101-2013 ASTM E1820:2016 BS 8571:2014 DNV RP F108-2006 ASTM E1921:2016 ASTM E399-12e3 5.13 Fracture Standards Overview Fatigue and Crack Propagation Fatigue Crack Growth Rate at ambient temperature ASTM E647-15e1 BS ISO 12108:2012 Load Controlled Low Cycle Fatigue at ambient temperature ASTM E466-15 BS 3518-1:1993 BS 3518-3:1963 Tensile Tensile (Forces up to 2000 kn) BS EN ISO 6892-1:2016 ASTM E8-/E8M-16a ASTM A370-17 Test Proc No 2.4 Tensile (temperature range ambient to 600ºC) (Forces up to 100 kn) BS EN ISO 6892-2 :2011 ASTM E21-09 Assessment Manager: NC2 Page 2 of 5
(cont d) Mechanical Tests (cont d) Charpy impact at temperatures between ambient and -130 C and at -196 C BS EN ISO 148-1:2010 ASTM E23-16b ASTM A370-17 Crystallinity BS 131:Part 5:1965(1996) Hardness Vickers hardness (HV 5 & 10) BS EN ISO 6507-1:2005 ASTM E92-16 Brinell hardness (1/30 HBW) BS EN ISO 6506-1:2014 ASTM E10-17 Rockwell hardness (HRBW and HRC scales) BS EN ISO 6508-1:2016 ASTM E18-16 Equotip hardness (Comparative) Tech Proc No 3.2 Weldments Tensile, Impact, Bend, Hardness, Macro / Micro-examination BS EN ISO 15614-1:2004+A2 :2012 BS EN ISO 15614-2:2005 BS EN 287:Part 1:2011 BS EN ISO 9606-1 :2013 BS EN ISO 9606-2:2004 BS EN ISO 4136:2012 BS EN ISO 9016:2012 BS EN ISO 5173:2010+A1:2011 BS EN ISO 5178 :2011 BS EN ISO 9015-1:2011 BS EN ISO 9017:2013 BS EN ISO 17639:2013 BS 4872:Part 1:1982(1995) BS 4872:Part 2:1976(1995) BS 4515-1:2009 BS 4515-2:1999 API 1104-21 st Edition:2013 API 6A 20 th edition AWS D1.1/D1.1M:2015 ASME IX- 2015 Assessment Manager: NC2 Page 3 of 5
(cont d) Metallurgical Tests Grain size (Comparison method) ASTM E112-2013 Volume fraction ASTM E562-11 Micro-examination - to determine microstructural constituents Method No. 4.14 Identification of Surface Structure and Modes of Failure No.4.12 using scanning electron microscopy %Ferrite by Feritscope Method No. 4.18 / C&I Surface examination using metallographic replica techniques Method No. 4.17 / C&I Corrosion Tests Duplex stainless steels Detecting detrimental intermetallic phases ASTM A923-14 (Method C) Iron, Steels and other ferrous metals Intergranular corrosion ASTM A262-15 Practice C ASTM A262-15 Practice E BS EN ISO 3651-2:1998 ASTM G28-02(2008) Method A Pitting and crevice corrosion resistance of stainless steels ASTM G48-11(2015) Method A BS 4515-2:1999 (Annex C) Hydrogen induced cracking (HIC) NACE TM0284-16 Sulphide stress corrosion cracking (SSCC) NACE TM0177-16 (Method A) NACE TM0316-16 ASTM G36-94 Assessment Manager: NC2 Page 4 of 5
Chemical Tests Plain carbon, low alloy and stainless steels Quantitative elemental analysis for: C, Si, Mn, P, S, Cr, Mo, N, Ni, Cu, V, Ti, Nb, Co, Zr, Pb, B and W 1.15 using optical emission spectroscopy Nickel and Nickel alloys Quantitative elemental analysis for: C, Si, Mn, P, S, Cu, N, Fe, Cr, Mo, Ti, Al and Nb 1.15 using optical emission spectroscopy Positive Material Identification by Hand Held XRF Method No. 1.18 / C&I END Assessment Manager: NC2 Page 5 of 5