LightCycler 480 Instrument Quick Guide

Transcription

1 LightCycler 480 Instrument Quick Guide For life science research use only. Not for use in diagnostic procedures.

2 This page intentionally left blank.

3 General Information The contents of this document, including all graphics and photographs, are the property of Roche Diagnostics. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Roche Diagnostics. Roche Diagnostics has made every reasonable effort to ensure that all the information contained in this manual is correct at the time of printing. However, Roche Diagnostics reserves the right to make any changes necessary without notice as part of ongoing product development. This LightCyler 480 Instrument Quick Guide was created by the Roche Diagnostics Corporation Commercial Education department. Direct questions or concerns regarding the contents of this document to: Roche Diagnostics Corporation Commercial Education Department 9115 Hague Road P.O. Box Indianapolis, IN USA LIGHTCYCLER is a trademark of Roche. The technology for LightCycler is licensed from Idaho Technologies, Inc. All other trademarks are the property of their respective owners. 2013, Roche Diagnostics. Distribution in USA by: Roche Diagnostics, Indianapolis, IN This LightCycler 480 Instrument Quick Guide is printed in the US. Additional copies of this document can be obtained by sending a message to: Indianapolis.Techpub@roche.com LightCycler 480 Quick Guide Page i

4 Revision History Revisions to this document are provided by Roche Diagnostics when necessary. No part of this document may be reproduced in any form or by any means without prior written consent. Publication Reference Number Date Revision Purpose November 2013 New Document Creation Page ii LightCycler 480 Quick Guide

5 LightCycler 480 Instrument Basics General Required Materials Standard Laboratory Equipment Product Name Microwell Plate Centrifuge Nuclease-free, aerosol-resistant pipette tips Microcentrifuge and 1.5 ml microcentrifuge tubes Micropipettes (P10 or P20, P200, P1000 or equivalent) Disposables Product Name Catalog Number Description LightCycler 480 Multi-well Plate 96-well - White plates and sealing foils LightCycler 480 Multi-well Plate 384-well - White plates and sealing foils LightCycler 480 Multi-well Plate 96-well - Clear plates and sealing foils LightCycler 480 Multi-well Plate 384-well - Clear plates and sealing foils LightCycler 480 Sealing Foil sealing foils Reagents Reaction Type Product Name Catalog Number Description Reverse Transcription with RNAse H activity SYBR Green Master High Resolution Melting Transcriptor 1st Strand cdna Synthesis Kit LightCycler 480 SYBR Green I Master LightCycler 480 High Resolution Melting Master Hybridization Probes LightCycler 480 Genotyping Master Hydrolysis Probes TaqMan Probes or Universal Probe Library (UPL) LightCycler 480 Probes Master For 50 (20 µl) reactions ml (5 x 20 µl) 2x concentrated Master Mix for 250 (20 µl) reactions ml (5 x 1 ml) 2x concentrated 25 ml MgCl2 stock solution for 500 (20 µl) reactions ml 5x concentrated Master Mix for 250 (20 µl) reactions ml (5 x 1 ml) 2x concentrated Master Mix for 250 (20 µl) reactions LightCycler 480 Control Kit Kit for quantitative Real-Time PCR and genotyping reactions LightCycler 480 Quick Guide Page 1

6 LightCycler 480 Instrument Basics This page intentionally left blank. Page 2 LightCycler 480 Quick Guide

7 LightCycler 480 Instrument Basics Getting Started 1. Log on to the LightCycler computer. Username: Password: Operator LC Start the LightCycler 480 software by double-clicking the <LightCycler480> icon. 3. Enter the username and assigned password to log in to the LightCycler 480 software. First Time Login (new database) Username: Password: admin LightCycler480 Normal Login Username: Password: admin Roche480 LightCycler 480 Quick Guide Page 3

8 LightCycler 480 Instrument Basics 4. The overview screen displays. This screen allows entry of a new experiment with or without use of a template for the conditions, or run a previously programed macro. Page 4 LightCycler 480 Quick Guide

9 LightCycler 480 Instrument Basics Software Navigation Overview Exit the software Logout of the current database Switch to Overview menu Display Navigator window Save the current experiment Export the current experiment to an.ixo file Close the current experiment Print the current screen Display Tools window Navigator window: displays the objects stored in the database as folders and files, allowing the user to work with objects in the database as well as import and export Exporting as.ixo: Tools window: creates a copy which can be imported to another computer or database allows user to change passwords, edit system settings, view database status and Error Log, define filter combination settings LightCycler 480 Quick Guide Page 5

10 LightCycler 480 Instrument Basics This page intentionally left blank. Page 6 LightCycler 480 Quick Guide

11 Create a New Experiment from Template New Experiment from Template Templates provide a convenient way to speed up the process of creating an experiment. You can use Roche general templates for the different types of Real-time PCR reactions, as well as create your own templates based on the specific conditions of your experiments. 1. Click New Experiment from Template in the Overview window. 2. The New Experiment from Template window displays the templates that match the connected instrument. LightCycler 480 Quick Guide Page 7

12 New Experiment from Template 3. Select a run template. a. Dual Color Hydrolysis Probes/UPL Probe duplex reactions using Hydrolysis Probes (UPL/TaqMan) labeled with FAM and VIC, HEX or Yellow 555 b. End-point Genotyping (PCR read) genotyping with FAM and VIC or HEX-labeled Hydrolysis or TaqMan probes, PCR and data collection (Allelic discrimination) c. End-point Genotyping (Pre-Post read) genotyping with FAM and VIC or HEX-labeled probes, data collection only, PCR performed in another instrument (Allelic Discrimination) d. Gene Scanning e. HybProbe basic protocol for High Resolution Melting experiments, including touch-down protocol reactions using Hybridization Probes, labeled with Fluorescein and LightCycler Red 640 f. Mono Color Hydrolysis Probe/UPL g. Simple Probes h. SYBR Green reactions with Hydrolysis Probes (UPL/TaqMan) labeled with FAM melting curve genotyping reactions using a single Fluorescein-labeled probe (Simple Probe) reactions using SYBR Green and simliar double-strand-intercalating dyes, includes melting curve 4. Click. The selected run-template is applied. 5. Modify run conditions (reaction volume, number of cycles, target temperature, hold, ramp rate, etc.) as needed. Page 8 LightCycler 480 Quick Guide

13 New Experiment from Template 6. The Start Run icon becomes active once the multi-well plate is loaded in the instrument. 7. Click Start Run. 8. Enter the experiment name in the dialog box. LightCycler 480 Quick Guide Page 9

14 New Experiment from Template Save Run Conditions as a Template If you modify the run conditions, you can save it as a new template for future use. 1. Open or create the run to be used as a template. 2. Click the drop-down next to Apply Template and select Save as Template. 3. Name the run template and select a location to save the template. Note: The default storage location for templates is the user s Template folder. 4. Click. The template is saved and will appear in the New Experiment from Template window in the future. Page 10 LightCycler 480 Quick Guide

15 Typical SYBR Green Reaction Protocol Reaction Setup Basic Real-Time Chemistry Protocols Reagent Final Concentration Volume (µl) / one reaction Water 1.0 Primer - Forward (5 µm Stock) 0.5 µm 2.0 Primer - Reverse (5 µm Stock) 0.5 µm 2.0 LightCycler 480 SYBR Green I Master 1x 10.0 Total 15.0 Add 5 µl template DNA for a total volume of 20 µl Run Program Program Name Cycles Analysis Mode Pre-incubation 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:05:00 Program Name Cycles Analysis Mode Amplification 45 Quantification Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:00:10 60 None 00:00:10 72 Single 00:00:10 Program Name Cycles Analysis Mode Melting Curve 1 Melting Curves Target ( C) Acquisition Mode Hold (hh:mm:ss) Acquisitions (per C) 95 None 00:00:05 65 None 00:01:00 97 Continuous 5 Program Name Cycles Analysis Mode Cooling 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 40 None 00:00:30 LightCycler 480 Quick Guide Page 11

16 Basic Real-Time Chemistry Protocols Typical Mono Color Hydrolysis Probe (TaqMan /UPL) Reaction Protocol Reaction Setup Reagent Final Concentration Volume (µl) / one reaction Water 0.6 Primer - Forward (5 µm Stock) 0.5 µm 2.0 Primer - Reverse (5 µm Stock) 0.5 µm 2.0 Probe (10 µm Stock) 0.2 µm 0.4 LightCycler 480 Probe Master 1x 10.0 Total 15.0 Add 5 µl template DNA for a total volume of 20 µl Run Program Program Name Cycles Analysis Mode Pre-incubation 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:10:00 Program Name Cycles Analysis Mode Amplification 45 Quantification Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:00:10 60 Single 00:00:30 72 None 00:00:01 Program Name Cycles Analysis Mode Cooling 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 40 None 00:00:30 Page 12 LightCycler 480 Quick Guide

17 Basic Real-Time Chemistry Protocols Typical Hybridization Probe (HybProbe) Reaction Protocol Reaction Setup Reagent Final Concentration Volume (µl) / one reaction Water 6.2 Primer - Forward (5 µm Stock) 0.5 µm 2.0 Primer - Reverse (5 µm Stock) 0.5 µm 2.0 Fluorescein Probe (10 µm Stock) 0.2 µm 0.4 Red Fluor Probe (10 µm Stock) 0.2 µm 0.4 LightCycler 480 Genotyping Master 1x 4.0 Total 15.0 Add 5 µl template DNA for a total volume of 20 µl Run Program Program Name Cycles Analysis Mode Pre-incubation 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:10:00 Program Name Cycles Analysis Mode Amplification 45 Quantification Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:00:10 60 Single 00:00:10 72 None 00:00:10 Program Name Cycles Analysis Mode Melting Curve 1 Melting Curves Target ( C) Acquisition Mode Hold (hh:mm:ss) Acquisitions (per C) 95 None 00:01:00 40 None 00:02:00 95 Continuous 5 Program Name Cycles Analysis Mode Cooling 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 40 None 00:00:30 LightCycler 480 Quick Guide Page 13

18 Basic Real-Time Chemistry Protocols This page intentionally left blank. Page 14 LightCycler 480 Quick Guide

19 Absolute Quantification Absolute Quantification Analysis Sample concentrations are calculated based on a standard curve created with standard samples along a concentration range with specific assigned values. The standard curve can be included within the run (internal standard curve) or generated in a previous run (external standard curve). Important: To use an external standard curve imported from a previous run, the software needs a reference point included in the current run. One concentration standard must be on every run to align the standard curve into the new run. The software shifts the imported standard curve based on how the reference standard compares to the previously run concentration. For more information, please consult Chapter D, Section (pages ) of the LightCycler 480 Operator s Manual. Crossing point (Cp) values (Cp is equivalent to Ct) are used to determine unknown sample concentrations from a standard curve. Performing an Absolute Quantification Analysis 1. Open the experiment you want to analyze in the main window. Note: Once the experimental run has completed, it remains open and ready to analyze. Previous experiments are located in the Experiments folder of the Navigator. 2. If sample information was entered during run setup, proceed to step 5. Otherwise, click Sample Editor on the left side of the active display. 3. In Sample Editor > Step 1: Select Workflow, select AbsQuant workflow. LightCycler 480 Quick Guide Page 1

20 Absolute Quantification 4. Enter Sample information a. In Sample Editor > Step 2: Select Samples, select wells. b. In Sample Editor > Step 3: Edit Abs Quant Properties, enter the appropriate sample information for the selected wells. Identify samples as Unknown or Standard samples, entering the appropriate concentration for each standard. c. For reactions in replicate, select all the wells and click Make Replicates. 5. Click Analysis. Page 2 LightCycler 480 Quick Guide

21 6. Select an analysis to create from the list. Important: Two algorithms are available to determine the crossing point: Absolute quantification/2nd derivative max automated, user input not required Absolute Quantification the point at which the maximum change in slope of the amplification curve becomes the crossing point Absolute quantification/fit Points user must set a threshold line the point at which the log-linear curve crosses the threshold line becomes the crossing point. 7. In the Create New Analysis dialog box, select an analysis subset and Quantification program (selected by default) and click OK. 8. If a standard curve was included in the experiment, select std curve (in run) from the drop-down menu. If an external standard curve needs to be imported, select std curve external. By default, all samples are included in results Double-click the check box next to the sample, or press the <space bar> to exclude a specific sample from the analysis Important: External Standard Curve - the external standard curve must be from an experiment with the same detection format, filter combination, and color compensation settings as the current experiment. The external curve and current experiments can be generated on different blocks (96 or 384). If using an External Standard Curve, you must include at least one of the Standard concentrations in the new experiment as a standard reference point for calculation. For more information, please consult Chapter D, Section (pages ) of the LightCycler 480 Operator s Manual. LightCycler 480 Quick Guide Page 3

22 Absolute Quantification 9. Click Calculate. To view the amplification curves for one or more samples, highlight the sample names in the sample list or click the corresponding well in the plate diagram. 10. To export individual data figures or tables, right-click within the information section you want to export, then choose the external format to use. Click the browse (...) button to browse to the location to save the file and assign a name to your export file. Click Export. 11. Export the entire experiment through the Navigator using the Export button. Map to the appropriate drive/ folder for saving. The complete file experiment can be imported into another computer with the same release of LightCycler 480 software. Page 4 LightCycler 480 Quick Guide

23 Relative Quantification Relative Quantification Analysis Relative Quantification compares the levels of two different target sequences in a single sample (e.g., target gene of interest (GOI) and another gene) and expresses the final result as a ratio of these targets. For comparison purposes the second gene is a reference gene that is found in constant copy numbers under all test conditions. The reference is used for normalization of sample-to-sample differences. The ratio of the same two sequences can be compared to a standard sample called a calibrator. The calibrator is typically a positive sample with a stable ratio of target-to-reference and is used to normalize all samples within one run, but in addition provides a constant calibration point between several LightCycler 480 System runs. Important: For more information, please consult Chapter D, Section 4.3 (pages ) of the LightCycler 480 Operator s Manual. Performing a Relative Quantification Analysis 1. Open the experiment for analysis in the main window. Note: If the experiment just completed, the run will remain open and ready for analysis. Previously created and performed experiments are located in the <Experiments> folder of the Navigator. 2. If the sample information was entered during run setup, then proceed to step 5. Otherwise, click the Sample Editor icon. Important: Relative Quantification Analysis uses the following identifiers for calculation, please note there are mandatory identifiers required: Note: If you are performing an experiment using different filter combinations, make sure you select the appropriate filter combination for entering the sample information. LightCycler 480 Quick Guide Page 1

24 Relative Quantification 3. In Sample Editor > Step 1: Select Workflow, select Rel Quant workflow. 4. Enter Sample information a. In Sample Editor > Step 2: Select Samples, select the wells that contain the same DNA samples. b. In Sample Editor > Step 3: Edit Rel Quant Properties, enter the appropriate sample name and sample type information for the selected wells. Note: For more information, please consult Chapter D, Section (page 183) of the LightCycler 480 Operator s Manual. Page 2 LightCycler 480 Quick Guide

25 Relative Quantification 5. Enter Gene target information. a. In Sample Editor > Step 2: Select Samples, select the wells that contain the same gene target. b. In Sample Editor > Step 3: Edit Rel Quant Properties, enter the appropriate target name and select target type (target or reference) information for the selected wells Note: Target is the gene of interest and Reference is the housekeeping gene (e.g., actin) 6. In Sample Editor > Step 2: Select Samples, select all the wells and set replicates by clicking Auto Replicate. LightCycler 480 Quick Guide Page 3

26 Relative Quantification 7. Click Analysis. Page 4 LightCycler 480 Quick Guide

27 8. Select Advanced Relative Quantification. Important: Two algorithms are available for the Relative Quantification Analysis Basic Relative Quantification automated, easy-to-use mode based upon the ΔΔCT-method Advanced Relative Quantification flexible mode, sophisticated software algorithms E-Method (Efficiency Method) Relative Quantification For more information, please consult Chapter D, Section (pages ) of the LightCycler 480 Operator s Manual. LightCycler 480 Quick Guide Page 5

28 Relative Quantification 9. Select all samples or subset to be analyzed and click. 10. Leave defaults and click. Note: For more information about this dialog box, please consult Chapter D, Section (pages ) of the LightCycler 480 Operator s Manual. Page 6 LightCycler 480 Quick Guide

29 11. The software automatically pairs the target to the corresponding reference. a. To obtain results, click Calculate. Relative Quantification Note: If a calibrator sample was used, the normalized ratio is the fold difference between samples and calibrator, represented as a red bar in the bar chart. If a calibrator sample was not used, then the Target/Ref Ratio column will provide results, comparing only target to reference amounts within a single sample, represented as a blue bar in the bar chart. Note: For more information, please consult Chapter D, Section (pages ) of the LightCycler 480 Operator s Manual. LightCycler 480 Quick Guide Page 7

30 Relative Quantification 12. To view amplification curves from the analysis or edit sample settings, click the Target Name tab and doubleclick on the corresponding Target Name. a. Once sample editing is complete, click Calculate, then click the Back to Rel Quant icon. Page 8 LightCycler 480 Quick Guide

31 b. Click the Rel Quant Results tab, then click Calculate to obtain updated results. Relative Quantification 13. To export individual data figures or tables, right-click within the information section you want to export, then choose the external format to use. Click the browse (...) button to browse to the location to save the file and assign a name to your export file. Click Export. 14. Export the entire experiment through the Navigator using the Export button. Map to the appropriate drive/ folder for saving. The complete file experiment can be imported into another computer with the same release of LightCycler 480 software. LightCycler 480 Quick Guide Page 9

32 Color Compensation Color Compensation Color Compensation is used to subtract fluorescent bleed-through from a reporter into inappropriate channels outside its dominant channel. While unnecessary for singleplex (one color) applications, color compensation is critical for multiplexed assays to resolve overlapping signals DF nm 521 nm 555 nm 607 nm 640 nm 668 nm Cyan 500 Fluorescein Hex Red 610 Red 640 Fluorescence Intensity w.e Cy Wav elength nm HTC II Emission Channels and Dye Spectra Why color compensate data? The premise of color compensation is that samples containing more than one fluorescence segregated from other contributing fluorescent signals. This is necessary because fluorescent dyes do not simply emit fluorescence at a single wavelength; rather their fluorescence is emitted over a broad range of wavelengths. The cast majority of fluorescent dyes have emission spectra covering a range of nm. Therefore, each emission produces at least some signal in each of the higher wavelength channels. The color compensation file makes it possible for the LightCycler 480 instrument to exclusively see, in any one channel, the fluorescent signal from the dye designated for that channel. Should I color compensate my Data? Color compensation is necessary only when running reactions that contain more than one signal-producing dye in a single well. LightCycler 480 Quick Guide Page 1

33 Color Compensation How do I setup color compensation reactions for a two or more color fluorescent system? Dedicate a reaction to each dye and one for a blank (no dye). For example, in a two color system, three reactions are necessary. Use dye concentrations similar to those used in the actual PCR µm for individual hydrolysis probes µm for HybProbe acceptor probes 0.2 µm for donor (FLUOS-labeled) HybProbe probes Note: The total concentration for FLUOS-labeled donor HybProbe probes in the mix should not exceed 1.2 µm. Prepare an equimolar mix of all donor HybProbe probes used in the assay. Check the quality of the dyes and probes used Note: High amounts of free, unlabeled dye can cause a high background signal that might impact color compensation. The free dye can be chosen if using a self-quenched probe (e.g., TaqMan or Molecular Beacon) but a positive reaction for the individual probe in the mix will also work DNA template must be added for the TaqMan Probe Color Compensation (adjust water volume) It is recommended to run the reactions in replicates of five. Below is a typical reaction setup: Page 2 LightCycler 480 Quick Guide

34 Example Reaction Setup for Hydrolysis/TaqMan probe-based Assay Reaction Blank Dye 1 Dye 2 10 µl Master Mix 10 µl Master Mix 10 µl Master Mix 10 µl Water 2.6 µl Water 2.6 µl Water 1 µl (10 µm stock) primer-forward target 1 1 µl (10 µm stock) primer-forward target 2 1 µl (10 µm stock) primer-reverse target 1 1 µl (10 µm stock) primer-reverse target µl probe target µl probe target 2 5 µl DNA template 5 µl DNA template Color Compensation Example Reaction Setup for HybProbe-based Assay Reaction Blank Dye 1 - Fluorescein Dye 2 Dye 3 10 µl Master Mix 10 µl Master Mix 10 µl Master Mix 10 µl Master Mix 10 µl Water 8 µl Water 8 µl Water 8 µl Water 2 µl Probe or Free Dye 2 µl Probe or Free Dye 2 µl Probe or Free Dye LightCycler 480 Quick Guide Page 3

35 Color Compensation How do I generate color compensation data? The temperature profile used in a color compensation protocol always includes heating, cycling, temperature, gradient, and cooling programs. The cycling program mimics a typical PCR, including data acquisition. Instead of running a separate color compensation experiment, you can also run the color compensation reactions in parallel to your experimental samples. In this case, apply the appropriate experimental PCR protocol but always add a temperature gradient or melting curves program with the color compensation analysis mode. Note: For hydrolysis probe color compensation runs, you must perform a real PCR, as cleavage of the probe by the Taq DNA polymerase during cycling is required to generate a fluorescent signal. Procedure 1. Open the LightCycler 480 Basic Software version and setup a run protocol as follows (adjust the amplification conditions to mimic the PCR you normally perform). The example below may differ from your PCR run. Program Name Cycles Analysis Mode Pre-incubation 1 None Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:05:00 Program Name Cycles Analysis Mode Amplification 45 Quantification Target ( C) Acquisition Mode Hold (hh:mm:ss) 95 None 00:00:10 60 Single 00:00:30 72 None 00:00:01 Program Name Cycles Analysis Mode Melting Curve 1 Color Compensation Target ( C) Acquisition Mode Hold (hh:mm:ss) Acquisitions (per C) 95 None 00:00:00 40 None 00:00:30 95 Continuous 1 Program Name Cycles Analysis Mode Cooling 1 None Page 4 Target ( C) Acquisition Mode Hold (hh:mm:ss) 40 None 00:00:30 2. Create a Subset including only the samples to create the color compensation. 3. In the Sample Editor, select the workflow Color Comp. 4. Select samples, identifying the color compensation subset to help navigate and enter sample information under the Color Comp Properties. LightCycler 480 Quick Guide

36 Color Compensation 5. In the Color Comp Properties, also enter sample information, indicating the appropriate dominant wavelength for each dye used in a particular well. How do I analyze the data? Following the color compensation run, the LightCycler 480 Basic Software version 1.5 saves the data generated as a normal experimental file. Important: For these data to be used for color compensation, you must first convert the data of the temperature gradient or melting curves program into a CC Object and save it separately. Procedure 1. When the experiment is finished, click Analysis. 2. From the Create New Analysis list, select Color Compensation. 3. In the Create New Analysis dialog box, select an analysis subset and a program in the experiment (typically there is only one color compensation or melting program selected by default). Click OK. 4. Click Calculate in the Action button area to perform the analysis. 5. Click Save CC Object. By default, the CCC folder in your Special Data folder is selected as the location. 6. Apply the color compensation data to another analysis or experiment if desired. How do I apply the color compensation? Procedure 1. Select the filter combination to display and compensate (Filter Combination button) for the analysis. 2. Click the down arrow next to the Color Compensation button and choose between the options <In Use> or <In Database>. 3. Select the color compensation object to apply and click OK. The experiment or the analysis charts are redrawn using the compensated data. Note that the Color Compensation button label indicates On. Note: The CC Object may also be applied to the Experiment/Data page, allowing the color compensation to be selected in all further analyses created on the experiment file. LightCycler 480 Quick Guide Page 5