Superior Internal & External Wall Finishes
|
|
- Austin Dawson
- 5 years ago
- Views:
Transcription
1 Superior Internal & External Wall Finishes
2 Polystat WFRP80 (Wall,Floor,Roof Panel) / (3000/2700/2400)x600x80mm H&V) Polystat WFRP95 (Wall,Floor,Roof Panel) / (3000/2700/2400)x600x95mm H&V) Polystat WFRP155 (Wall,Floor,Roof Panel) / (3000/2700/2400)x600x155mm H&V) Tecoblock L Tecoblock D Tecoblock D Locator Endcap All Purpose Acrylic Highbuild (APAH) Dry Texture (DT) Concrete Finish (CFLG,CFG,CFW) Concrete Patch (CPG,CPOW,CPW) Liquid Plasterboard Lustro Wax Marble Finish Granular Diamond Finish Granular Glass Primer External Paint Applicator Pump Machine Applicator Trowel Attachment Applicator Mortar Attachment Applicator Spray Gun Attachment Applicator Notch Tool Attachment Applicator Corner Tool Attachement Full Range of Rendering Tools Other custom made products include *Architectural Mouldings *Fence Cappings, Pier Caps *Outdoor Steps *Columns *Pizza Ovens *Pre-built Walls and Structures + Range of Accessories
3 All Purpose Acrylic Highbuild The Worlds leading base coat application material for all building substrates. This unique formulation has been developed for ease of use, incomparable spreadability, ultra highbuild capability, high adhesion properties, thermal performance and extremly light weight. Coharo Coatings - All Purpose Acrylic Highbuild has many uses. Firstly the ultimate base coat for preparing your wall for your desired finish, solid light weight mouldings, pizza oven insulation, as an adhesive, rough cast finish and also as a variety of finishes depending on tools and application. All Purpose Acrylic Highbuild also works in conjunction with our Pango - Applicator Pump Machine to deliver speed of application where the material flows out of the trowel onto the wall. Casafico are dedicated to utilising waste streams to create quality products for a sustainable future. This revolutionary material is made utilising 8 Litres of waste which would have gone to landfill. One Material Any Surface!! The Ultimate Formulation! *Just add 4 to 5 Litres water and mix. *1 Bag fills a 15 Litre bucket mixed. *1 to 6m2 coverage (15mm to 3mm build). *3mm minimum application, upto 50mm in one pass. *Ultra Light weight - each bag weighs only 10 Kg. *Thermal Performance. *Designed for use on all Casafico building products. *Apply by trowel or Pango machine. *Works on all substrates - brick, block, blueboard, cement sheet, AAC, polystyrene, painted brick etc... Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 11 Ltr / 10 Kg bag (60 or 80 bags/pallet) APAH
4 Coharo Coatings Technical Data All Purpose Acrylic Highbuild - APAH Description: Coharo Coatings All Purpose Acrylic Highbuild is a revolutionary formulation of quality particles which creates the worlds leading base coat application material for all building substrates. The material is ultralight as there is no sand aggregate, extremely easy to apply and spread on the wall, with the ability to apply a minimum of a 3mm to 50mm coat. This makes All Purpose Acrylic Highbuild incomparable in performance for the preparation and levelling of your wall for your desired finish. Coverage: 1-6 m2 (15mm to 3mm build) Packaging: 11 Litre / 10kg Paper Bags 60 or 80 Bags per Pallet Features & Benefits: Ultra Highbuild performance Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply Just add water and mix Thermal Performance Makes Light weight Mouldings Suitable Substrates: Polystat WFR Panel Tecoblock Concrete Block & Painted Concrete Block Clay Brick & Painted Brick Concrete Precast Panel Fibre Cement Sheet Blue Board Expanded and Extruded Polystyrene Autoclaved Aerated Concrete - AAC Surface Preparation: The substrate must be clean and dry/cured before applying All Purpose Acrylic Highbuild. Any crumbling, loose or damaged substrate must be removed. All surfaces must be free from grease, oils, dirt and dust. Prepainted surfaces must have flaking paint wire brushed back to solid substrate. Mixing: Add 4 Litres of water to a 15 Litre bucket and pour contents of bag into bucket. Mix using a slow Speed drill with a suitable paddle. It should be mixed until a lump free homogenous mix is achieved. Applicator should add water or product to achieve desired consistency. Should the material be too wet or dry it may be difficult to apply. Application: All Purpose Acrylic Highbuild is applied by trowel or Pango Applicator Pump Machine. Once applied, material can be screeded by the use of a large trowel to level the wall for its preparation of a finish coat. Embedment of Fibreglass mesh will increase its strength and should be used where required. Any corner angle to be used must be glued and levelled with All Purpose Acrylic Highbuild, not liquid nails or nails. All Purpose Acrylic Highbuild can also be floated when necessary. Curing time is dependent on thickness applied and can be between 1 to 7 days. All Purpose Acrylic Highbuild must be cured before the application of a wet texture or paint. Care should be taken in the preparation of the work area; areas not to be coated should be masked and protected. Material can be difficult to remove if allowed to dry on windows or unwanted areas. To achieve a rough cast effect the material should be sprayed on with the Pango Applicator Pump Machine or flicked on with an appropriate trowel. To make light weight mouldings or castings, material can be poured into a mould once mixed with the use of an appropriate release agent, left to cure before being removed. Safety: All Purpose Acrylic Highbuild is alkaline in nature and can cause irritations to people with sensitive skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
5 Liquid Plasterboard Coharo Coatings Liquid Plasterboard introduces a revolution to the wall coating industry, a change for a better future and a superior quality finish. A coating material that utilises a selected range of quality recycled materials which have been manufactured into a coating material. No extra water on site is required to mix the product. Liquid Plasterboard consists of two parts. Part A is the Liquid Mix which holds the water and key ingredients for the performance of the product. Part B is the Dry Mix specially formulated. The 2 parts mixed together creates Coharo Coatings Liquid Plasterboard. Casafico are dedicated to utilising waste streams to create quality products for a sustainable future. This revolutionary material is made utilising waste which would have gone to landfill. One Material Any Surface! The Ultimate Patching compound! Smooth Feature Finish! An alternative to Hard Plaster! Creates the Tuscany Look! *Just mix the 2 parts together! *1 Box creates 14 Litres mixed. *10 to20m2 coverage. *1 to 3mm application. *Internal and External application. *Suitable for refacing old plaster where joints are visible. *Flexible and a warm plasterboard feel. *Sandable if required. *Colour options available. *Can be polised for a smooth feature finish. *Designed for use on all Casafico building products. *Apply by trowel or Pango machine. *Works on all substrates. *Enhanced performance through ease of application and time management! Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 2x9 Ltr bags in a box Creates 14 Lt Mixed 19.5 Kg box (40 boxes/pallet) LP
6 Coharo Coatings Technical Data Liquid Plasterboard - LP Description: Coharo Coatings Liquid Plasterboard is a revolutionary formulation of quality particles. Liquid Plasterboard consists of two parts. Part A is the Liquid Mix which holds the water and key ingredients for the performance of the product. Part B is the Dry Mix specially formulated. No extra on site water is required to mix the product. Liquid Plasterboard can reface old or new plasterboard bringing it to a level 5 finish. LP can be polished by S/S trowel to achive a hard wearing shiny finish. LP can be finished by a sponge float to create a Tuscany look. LP can be used as a patching compound. LP can be coloured and a selection of aggreates are available to create many unique finishes. Coverage: m2 Packaging: 2 x 9 Litre bags in a box (creates 14 Lt Mixed) / 19.5kg Boxes 40 Boxes per Pallet Features & Benefits: An alternative to hard plaster Enhanced performance Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply Just mix the 2 parts together Polish for a smooth feature finish Creates the Tuscany look Suitable Substrates: Plasterboard Polystat WFR Panel Tecoblock Concrete Block & Painted Concrete Block Over any rendered surface Concrete Precast Panel Fibre Cement Sheet Blue Board Expanded and Extruded Polystyrene Autoclaved Aerated Concrete - AAC Surface Preparation: The substrate must be clean and dry/cured before applying Liquid Plasterboard. Any crumbling, loose or damaged substrate must be removed. All surfaces must be free from grease, oils, dirt and dust. Prepainted surfaces must have flaking paint wire brushed back to solid substrate. Mixing: Empty contents in a 15 Litre bucket (Part A Liquid Mix first then Part B Dry Mix) and mix using a slow speed drill with a suitable paddle. It should be mixed until a lump free homogenous mix is achieved. Application: Liquid Plasterboard is applied by trowel or Pango Applicator Pump Machine. Finish by hard wearing sponge float or stainless steel trowel depending on desired outcome. Can be sanded if required. Embedment of Fibreglass mesh will increase its strength and should be used where required. Any corner angle to be used must be glued and levelled with Liquid Plasterboard, not liquid nails or nails. Curing time is dependent on thickness applied and can be between 1 to 2 days. Liquid Plasterboard must be cured before the application of a wet texture or paint. Care should be taken in the preparation of the work area; areas not to be coated should be masked and protected. Material can be difficult to remove if allowed to dry on windows or unwanted areas.. Safety: Liquid Plasterboard is alkaline in nature and can cause irritations to people with sensitive skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
7 Dry Texture Coharo Coatings Dry Texture is a revolutionary formulation of quality particles which creates the worlds leading texture coat application material for all building substrates. This unique formulation has been developed especially for application over Coharo Coatings - All Purpose Acrylic Highbuild - APAH. It is easy to apply, floatable, has high adhesion properties which achieves a traditional textured finish. This Revolutionary material is made utilizing waste glass which would have gone to landfill. The quality glass aggregate, which is crushed to a 1mm particle size, takes all the risk out from iron contamination from the traditional sand aggregate based products from other manufacturers. Casafico are dedicated to utilising waste streams to create quality products for a sustainable future. This revolutionary material is made utilising 8 Litres of waste which would have gone to landfill. Traditional Textured Finish!! Quality Glass Aggregate! *Just add 4 to 5 Litres of water and mix. *1 Bag fills a 15 Litre bucket mixed. *6 to 8m2 coverage. *Apply over APAH for your desired finish. *Each bag weighs 19 Kg. *Designed for use on all Casafico building products. *Apply by trowel and floatable. *Works on all substrates - brick, block, blueboard, cement sheet, AAC, polystyrene, painted brick etc... Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 11 Ltr / 19 Kg bag (50 bags/pallet) DT
8 Coharo Coatings Technical Data Dry Texture DT Description: Coharo Coatings Dry Texture is a revolutionary formulation of quality particles which creates the worlds leading texture coat application material for all building substrates. This unique formulation has been developed especially for application over Coharo Coatings - All Purpose Acrylic Highbuild - APAH. It is easy to apply, floatable, has high adhesion properties which achieves a traditional textured finish. This Revolutionary material is made utilizing waste glass which would have gone to landfill. The quality glass aggregate, which is crushed to a 1mm particle size, takes all the risk out from iron contamination from the traditional sand aggregate based products from other manufacturers. Coverage: 6-8 m2 Packaging: 11 Litre / 19kg Paper Bags 50 Bags per Pallet Features & Benefits: Traditional Textured Finish Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply Just add water and mix Suitable Substrates: Over All Purpose Acrylic Highbuild APAH Polystat WFR Panel Tecoblock Concrete Block & Painted Concrete Block Clay Brick & Painted Brick Concrete Precast Panel Fibre Cement Sheet Blue Board Expanded and Extruded Polystyrene Autoclaved Aerated Concrete AAC Over any Rendered Surface Surface Preparation: The substrate must be clean and dry/cured before applying Coharo Coatings Dry Texture DT. Any crumbling, loose or damaged substrate must be removed. All surfaces must be free from grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to solid substrate. Mixing: Add 4 Litres of water to a 15 Litre bucket and pour contents of bag into bucket. Mix using a slow speed drill with a suitable paddle. It should be mixed until a lump free homogenous mix is achieved. Applicator should add water or product to achieve desired consistency. Should the material be too wet or dry it may be difficult to apply. Application: Dry Texture DT is applied by trowel. Once applied, material can be floated to achieve the textured finish. Curing time is dependent on thickness applied and can be between 1 to 7 days. Dry Texture DT must be cured before the application of paint. Care should be taken in the preparation of the work area; areas not to be coated should be masked and protected. Material can be difficult to remove if allowed to dry on windows or unwanted areas. Safety: Dry Texture DT is alkaline in nature and can cause irritations to people with sensitive skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
9 Concrete Finish Coharo Coatings Concrete Finish is an aesthetically pleasing smooth finish material to give an appearance of a concrete panel. Apply Concrete Finish 1st Coat, be generous with the material, it s very fine as there is no aggregate (.3 to.5mm thick to fill in the base coat). Leave to completely touch dry (from 30mins to 2 Hours). Apply Uniformly second coat, avoid trowel marks as much as possible once touch dry, spray fine mist of clean water and finish with sponge float till the mist is dry and sponge is slippery on the surface. Trowel finish can create more markings if required and compact the surface for a less porous shinier finish. Available in grey, light grey and pure white which can be tinted to colour of choice. Smooth Feature Finish!! An alternative to Hard Plaster! *Just add 4 to 5 Litres of water and mix. *1 Bag fills a 15 Litre bucket mixed. *10 to 20m2 coverage. 0.5 to 1mm application *Apply over APAH for your desired finish. *Each bag weighs 15 Kg. *Designed for use on all Casafico building products. *Apply by trowel and floatable by sponge float. *SS Trowel Finish polished. *Works on all prepared substrates. *Simulates precast. Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 11 Ltr / 15 Kg bag (50 bags/pallet) CFG, CFLG, CFW
10 Coharo Coatings Technical Data Concrete Finish CF Description: Coharo Coatings Concrete Finish is an aesthetically pleasing smooth Finish material to give an appearance of a concrete panel. Apply Concrete Finish 1st Coat, be generous with the material, it s very fine as there is no aggregate (.3 to.5mm thick to fill in the base coat). Leave to completely touch dry (from 30mins to 2 Hours). Apply Uniformly second coat, avoid trowel marks as much as possible once touch dry, spray fine mist of clean water and finish with sponge float till the mist is dry and sponge is slippery on the surface. Trowel finish can create more markings if required and compact the surface for a less porous shinier finish. Coverage: m2 Colour: Grey, Light Grey & White (CFG, CFLG,CFW) Packaging: 11 Litre / 15kg Paper Bags 50 Bags per Pallet Features & Benefits: Simulates Precast Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply Just add water and mix Suitable Substrates: Over All Purpose Acrylic Highbuild APAH Polystat WFR Panel Concrete Precast Panel Fibre Cement Sheet Blue Board Over any Rendered Surface Surface Preparation: The substrate must be clean and dry/cured before applying Coharo Coatings Concrete Finish CF. Any crumbling, loose or damaged substrate must be removed. All surfaces must be free from grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to solid substrate. Mixing: Add 4 Litres of water to a 15 Litre bucket and pour contents of bag into bucket. Mix using a slow speed drill with a suitable paddle. It should be mixed until a lump free homogenous mix is achieved. Applicator should add water or product to achieve desired consistency. Should the material be too wet or dry it may be difficult to apply. Application: Concrete Finish CF is applied by trowel. Apply Concrete Finish 1st Coat, be generous with the material, it s very fine as there is no aggregate (.3 to.5mm thick to fill in the base coat). Leave to completely touch dry (from 30mins to 2 Hours). Apply Uniformly second coat, avoid trowel marks as much as possible once touch dry, spray fine mist of clean water and finish with sponge float till the mist is dry and sponge is slippery on the surface. Trowel finish can create more markings if required and compact the surface for a less porous shinier finish. Care should be taken in the preparation of the work area; areas not to be coated should be masked and protected. Material can be difficult to remove if allowed to dry on windows or unwanted areas. Safety: Concrete Finish CF is alkaline in nature and can cause irritations to people with sensitive skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
11 Concrete Patch Coharo Coatings Concrete Patch is a lightweight concrete patching mortar. Concrete Patch is manufactured and blended from high grade materials to provide maximum strength and bonding with a smooth finish to suit most grades of concrete substrates. Concrete Patch is particularly recommended for patching and covering the metal joining plates and non-structural repairs to precast and tilt-up concrete panels and many other examples of concrete construction works. Casafico are dedicated to utilising waste streams to create quality products for a sustainable future. This revolutionary material is made utilising 8 Litres of waste which would have gone to landfill. One pass to Match Precast!! Highbuild Performance! *Just add 3 Litres water and mix. *1 Bag fills a 15 Litre bucket mixed. *Fills Large Voids. *Upto 100mm application in one pass. *Light weight - each bag weighs only 12 Kg. *Thermal Performance. *Designed for use on all Casafico building products. *Apply by trowel. *Also a patching compound for mouldings.. Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 11 Ltr / 12 Kg bag (60 or 80 bags/pallet) CPG, CPOW, CPW
12 Coharo Coatings Technical Data Concrete Patch - CP Description: Coharo Coatings Concrete Patch is a lightweight concrete patching mortar. Concrete Patch is manufactured and blended from high grade materials to provide maximum strength and bonding with a smooth finish to suit most grades of concrete substrates. Concrete Patch is particularly recommended for patching and covering the metal joining plates and non-structural repairs to precast and tilt-up concrete panels and many other examples of concrete construction works. Coverage: 12 Ltr FIll per bag Colour: Grey, Off White & White (CPG, CPOW, CPW) Packaging: 11 Litre / 12kg Paper Bags 60 or 80 Bags per Pallet Features & Benefits: One pass to match precast Fill Large Voids Highbuild performance Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply Just add water and mix Thermal Performance Patching compound for mouldings Suitable Substrates: Concrete Precast Panel Clay Brick Polystat WFR Panel Tecoblock Concrete Block Over APAH Surface Preparation: The substrate recess areas for patching must be clean of all loose fragments, eradicate or remove any dust, paint, oil or chemicals and bond breaker or curing compound, back to a clean and dry concrete surface. Blow away all dust from surface to achieve best bonding results. Mixing: Add 3L of water to one 11 litre bag of Coharo Coatings - Concrete Patch. Add water first and then add the dry powder to avoid lumps. This will achieve a no slump mixture similar to pizza dough or a stiff but pliable homogeneous consistency. This will allow you to load a steel trowel and force/push the mixed Concrete Patch into the joining plate recesses or repair depressions. Application: Simply push the Concrete Patch material firmly into an overall situation and trowel off any excess to match the concrete substrate. Can also be floated with a piece of polystyrene to achieve a flat uniform finish. Safety: Coharo Coatings - Concrete Patch is alkaline in nature and can cause irritations to people with sensitive skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
13 Granular Diamond Finish Coharo Coatings - Granular Diamond Finish is your final decorative coating to achieve a unique texture which glistens in the sun. Unlike the usual textured finish, this is sure to impress. Granular Diamond Finish is ready to apply, the formulation has been developed for ease of use, high adhesion and water resistance properties. Available it any colour of choice. Casafico are dedicated to utilising waste streams to create quality products for a sustainable future. This revolutionary material is made utilising 9 Litres of waste which would have gone to landfill. The Elegant Final Touch!! Quality Glass Aggregate! *Immediate application on prepared substrate. *8 to 9 m2 coverage. *1mm glass aggregate. *Apply by Stainless Steel Trowel. *Designed for use on all Casafico building products. *Works on all prepared substrates. Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 15 Ltr / 20 Kg bucket (48 buckets/pallet) GDF
14 Coharo Coatings Technical Data Granular Diamond Finish - GDF Description: Coharo Coatings Granular Diamond Finish is your final decorative coating to achieve a unique texture which glistens in the sun. Unlike the usual textured finish, this is sure to impress. This Revolutionary material is made utilizing waste glass which would have gone to landfill. The quality glass aggregate, which is crushed to a 1mm particle size, takes all the risk out from iron contamination from the traditional sand aggregate based products from other manufacturers. Granular Diamond Finish is ready to apply, the formulation has been developed for ease of use, high adhesion and water resistance properties. Available in any colour of choice. Coverage: 8-9 m2 Packaging: 15 Litre / 20kg Plastic Buckets 48 Buckets per Pallet Features & Benefits: Glistening Textured Finish Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply Suitable Substrates: Over All Purpose Acrylic Highbuild APAH Polystat WFR Panel Tecoblock Concrete Precast Panel All prepared surfaces Surface Preparation: The substrate must be clean and dry/cured before applying Coharo Coatings Granular Diamond Finish. Any crumbling, loose or damaged substrate must be removed. All surfaces must be free from grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to solid substrate. Mixing: Ready to Apply, can be mixed to ensure colour consistency if self tinting. Application: Granular Diamond Finish is applied by trowel. Once applied, material can be floated but not necessary. Curing time is dependent on weather and is generally 1 to 2 Days. Granular Diamond finish should not be applied if rain is predicted for the day of application outdoors. Care should be taken in the preparation of the work area; areas not to be coated should be masked and protected. Material can be difficult to remove if allowed to dry on windows or unwanted areas. Safety: Granular Diamond Finish can cause irritations to people with sensitive skin. During use, avoid contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
15 Marble Finish Coharo Coatings Marble Finish is a glossy decorative coating. It is applied using a stainless steel trowel and polished until your reflection is visible. Marble Finish can be tinted to any colour. Normally applied in at least two to three coats onto a flat surface and with artistic trowel techniques to achieve various effects. Coharo Coatings Marble Finish is the most elegant finish for that feature wall. It is ready to apply, the formulation has been developed for ease of use, high adhesion and water resistance properties. Available in any colour of choice. Polished Feature Finish!! An impressive Coating! *Immediate application on prepared substrate. *4 m2 / Ltr coverage. *Reflective Feature Finish. *Apply by Stainless Steel Trowel. *Designed for use on all Casafico building products. *Works on all prepared substrates. Eliminate all the issues of sand based products from every other manufacturer and help make a difference to our environment! 15 Ltr / 15 Kg bucket 2 Ltr / 2 Kg bucket (48 buckets/pallet) MF
16 Coharo Coatings Technical Data Marble Finish - MF Description: Coharo Coatings Marble Finish is a glossy decorative coating. It is applied using a stainless steel trowel and polished until your reflection is visible. Marble Finish can be tinted to any colour. Normally applied in at two toleast three coats onto a flat surface and with artistic trowel techniques to achieve various effects. Coharo Coatings Marble Finish is the most elegant finish for that feature wall. It is ready to apply, the formulation has been developed for ease of use, high adhesion and water resistance properties. Available in any colour of choice. Coverage: 4 m2 per Ltr. Packaging: 15 Litre or 2 Ltr Plastic Buckets Features & Benefits: Polished Feature Finish Strong adhesion Excellent crack resistance Excellent water resistance Easy to apply SS Trowel Finish polished Reflective Feature Finish Suitable Substrates: Over Concrete Finish CF Polystat WFR Panel Tecoblock Concrete Precast Panel All prepared surfaces Surface Preparation: The substrate must be clean and dry/cured before applying Coharo Coatings Marble Finish. Any crumbling, loose or damaged substrate must be removed. An application of Concrete Finish or Primer may be necessary prior the application of Marble Finish to achieve desired result. All surfaces must be free from grease, oils, dirt and dust. Pre-painted surfaces must have flaking paint wire brushed back to solid substrate. Mixing: Ready to Apply, can be mixed to ensure colour consistency if self tinting. Application: Marble Finish is applied by stainless steel trowel. Once applied, a second coat can be applied when touch dry. Firm pressure with the trowel will compact he material and create a high density polished feature finish.curing time is dependent on weather and is generally 1 to 2 Days. Marble finish should not be applied if rain is predicted for the day of application outdoors. Care should be taken in the preparation of the work area; areas not to be coated should be masked and protected. Material can be difficult to remove if allowed to dry on windows or unwanted areas. Safety: Marble Finish can cause irritations to people with sensitive skin. During use, avoid contact with skin and eyes. Wear suitable protective gloves and mask while handling the product. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The product is non-toxic and is not flammable. For further information, please call or visit our website
Product Data Sheet. Description. Uses. Suitable Surfaces. Polymer enhanced, pre-blended, bag mix, coarse float render.
Product Data Sheet Render MaxiCoarse Polymer enhanced, pre-blended, bag mix, coarse float render. Description MaxiCoarse Render is a pre-blended, polymer fortified cement based render mix, formulated to
More informationMONOBASE AAC/ SIDER-PLAST THE ULTIMATE EXTERIOR HARD COAT STUCCO SYSTEM FOR AUTOCLAVED AERATED CONCRETE
SIDER-CRETE, INC. 153 Regur Road Hawkinsville, GA 31036 USA Ph: 478.892.9800 www.sider-crete.com MONOBASE AAC/ SIDER-PLAST THE ULTIMATE EXTERIOR HARD COAT STUCCO SYSTEM FOR AUTOCLAVED AERATED CONCRETE
More informationSIDER-BASE CONCENTRATE AAC/ MONOSIDERAL AAC THE ULTIMATE OLD-WORLD AERATED CONCRETE-AAC DECORATIVE STUCCO SYSTEM
SIDER-CRETE, INC. 153 Regur Road Hawkinsville, GA 31036 USA Ph: 478.892.9800 www.sider-crete.com SIDER-BASE CONCENTRATE AAC/ MONOSIDERAL AAC THE ULTIMATE OLD-WORLD AERATED CONCRETE-AAC DECORATIVE STUCCO
More informationFinishes. The visual quality of your finished wall or ceiling is dependent on the quality of workmanship and quality of the materials used.
Finishes The visual quality of your finished wall or ceiling is dependent on the quality of workmanship and quality of the materials used. Knauf lead the way in modern, highly developed finishing materials
More informationE.MIX MOISTURE SEALER
E.MIX Super Fast Fix Fast setting, high performance, high strength, highly flexible, strong polymerized thin bed tile adhesive for interior and exterior wall tile fixing complied with C2FTE class of EN
More informationPPC Cement TUTORIAL. how to screed a floor
PPC Cement TUTORIAL how to screed a floor Pre-build: TOOLs & Materials ITEM Quantity Check. Builders bucket. Wheelbarrow 3. Shovel 4. Builder s line 5. 50mm steel pegs 6. Rigid timber forms 7. Flexible
More informationRemoving or plastering over artex
Removing or plastering over artex Artex is a water-based covering, usually used to decorate ceilings, and generally brought to a textured finish with the use of a brush or roller. Some older artex may
More informationPool Plasters & Pool Paint
72 Pool Plasters & Pool Paint Comprised of waterproof marble based plaster and cement-based paint, for the new and renovations markets in the pool industry, available in a range of colours. weber-tylon.co.za
More informationHEAD OFFICE 22 Park Drive Dandenong VIC Phone: (03) Fax (03)
Technical Data Sheet Unitex Polymer Render Unitex Polymer Render is an acrylic polymer-rich wet render for thin trowel-applied one coat applications with the highest adhesion and flexibility that Unitex
More informationOMNITEK Deco is suitable for all leveling and thin layer concrete repair applications, such as:
OMNITEK Deco High strength leveling mortar, Class R4 Product Description OMNITEK Deco is a high strength, cement based, volume stable mortar, suitable for leveling and finishing of concrete surfaces in
More informationProduct Specification
Product Specification Product Name: PORTER S MINERAL SILICATE STAIN PRODUCT DESCRIPTION: is a highly durable coloured silicate dispersion stain for the decoration and protection of old and new fair-faced
More informationBONDGROUT GP ( GENERAL PURPOSE NON-SHRINK STRUCTURAL GROUT) Page 1 / 7.
BONDGROUT GP Page 1 / 7. is a ready-mixed, non-shrink, nonmetallic, flowable, highstrength structural grout. contains a balanced blend of washed and graded silica sands, Portland cement flow improvement
More informationPRODUCT DRYMIX CODEMIX
December 2018 Page 1 of 5 PRODUCT DRYMIX is a proprietary blend of clean, well graded sand, cement, lime, fillers and admixtures that is engineered to produce top quality finished properties while maintaining
More informationMapetherm AR1 Light. Lightweight one-component cementitious mortar FOR THERMAL INSULATION WITH SUPERIOR LIGHTNESS AND ASTONISHING PERFORMANCE
Mapetherm AR1 Light Lightweight one-component cementitious mortar FOR THERMAL INSULATION WITH SUPERIOR LIGHTNESS AND ASTONISHING LIGHTWEIGHT Mapetherm AR1 Light One-component, lightweight cementitious
More informationJewel Stone. Decorative Concrete Overlay System. Part 1 GENERAL MANUFACTURER S SPECIFICATION
SEPTEMBER 2016 Jewel Stone Decorative Concrete Overlay System MANUFACTURER S IFICATION 09 62 81 Part 1 GENERAL 1.1 RELATED SECTIONS.1 Specification 03 30 00 Cast-in-Place Concrete.2 Specification 09 70
More informationMethod Statement. For RSA Cement Renders Over Masonry Substrates
Method Statement RSA Masonry Renders, Traditional Render and EP Render are all suitable for application over correctly prepared clay bricks and concrete blocks PREPARATION Cleaning:- Ensure all surfaces
More informationData sheet Armatop A - new / Page 1. Areas of application Bonding Bonding of mineral wool, polystyrene and cork external wall insulation boards.
Data sheet Armatop A - new / Page 1 Armatop A - new Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of mineral wool, polystyrene and cork external
More informationARTEX AND PLASTER. 2 - Choosing the right product
ARTEX AND PLASTER Proper plastering is not easy. But DIY plasters are designed with ease of use in mind, and Artex TM is no more difficult to apply than thick paint. It is best to wear gloves when mixing
More information3-part thixotropic epoxy patching mortar
Product Data Sheet Edition 28/08/2006 Identification no: 02 04 02 03 001 0 000044 3-part thixotropic epoxy patching mortar Construction Product Description Uses Characteristics / Advantages Sikadur -41
More informationFor RSA Coating Systems over For RSA Coating Systems over Austech Foamula Extruded Polystyrene (XPS) (Skin Off)
Austech Foamula Extruded Polystyrene (XPS) (Skin Off) RSA strongly recommend the use of our full render and texture systems with the appropriate water tight membrane over polystyrene products. SEVEN STEPS
More informationApplication Instructions for Keystone Kool Deck on Existing Concrete
Application Instructions for Keystone Kool Deck on Existing Concrete REQUIRED MATERIALS Keystone Kool Deck PTA Bonding Agent Water 20 Mesh Marble Sand White Portland Cement OPTIONAL TOOLS Mortex Pattern
More informationPlastering. Holiday Inn - Sultanate of Oman
1 208 Holiday Inn - Sultanate of Oman Gyproc GypFine Plasters provide the ultimate skimming solutions for today s high-end finish. They are formulated to suit a wide variety of backgrounds including plasterboard,
More informationApplication Guide. PaveCoat
Application Guide PaveCoat This guide has been developed to provide comprehensive preparation and application recommendations for a variety of concrete surfaces. Whilst all endeavours have been taken to
More informationCP-24CC Potassium Silicate Concrete
CP-24CC Potassium Silicate Concrete PRODUCT DESCRIPTION Blome CP-24CC is a two component, potassium silicate concrete used for acid resistant pump pads, equipment pads, curbing, floors and sumps. CP-24CC
More informationCOVERFLEX TWO-PART ELASTOPLASTIC CEMENT MORTAR FOR WATERPROOFING APPLICABLE WITH ROLL, BRUSH OR TROWEL. DESCRIPTION FIELDS OF APPLICATION
TWO-PART ELASTOPLASTIC CEMENT MORTAR FOR WATERPROOFING APPLICABLE WITH ROLL, BRUSH OR TROWEL. DESCRIPTION FIELDS OF APPLICATION COVERFLEX is a special two-part plastic cement mortar consisting of cementitious
More information3910 E. McKinney Denton, TX P.O. Box Dallas, TX EZ WALL CONCENTRATE, INC
EZ Spread Coarse Sand Description EZ Spread is the perfect material for small projects and repairs. This factory prepared blend of portland cement proprietary additives, and sand. EZ Spread is designed
More informationApplication Guidelines
Baumit Renders for Porotherm Masonry Application Guidelines Light and easy application Tried and tested EWI system compatible Ideas with a future. Renders for Porotherm Masonry Baumit lightweight render
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT WATER-BASED DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat Water-Based is a fast dry floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists
More informationSystem Recommendation SR0618
Ardex Australia Pty Ltd ABN 82 000 550 005 Unit 7, 20 Powers Road, Seven Hills NSW 2147 Australia Telephone + 61 2 9851 9100 Facsimile +61 2 9838 7970 www.ardexaustralia.com System Recommendation SR0618
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and
More informationMethod Statement. For RSA Coating Systems Over AAC Lightweight Blocks N.B. Please refer to separate Application Guidelines for AAC Lightweight Panels
Method Statement For RSA Coating Systems Over AAC Lightweight Blocks RSA strongly recommend the use of our full render, texture and protective coating systems over AAC lightweight blocks. We DO NOT recommend
More informationMethod Statement. For RSA Coating Systems Over AAC Lightweight Blocks N.B. Please refer to separate Application Guidelines for AAC Lightweight Panels
Method Statement For RSA Coating Systems Over AAC Lightweight Blocks RSA strongly recommend the use of our full render, texture and protective coating systems over AAC lightweight blocks. We DO NOT recommend
More information1 ST KOTE HI COVER PVA
1 ST KOTE HI COVER PVA DESCRIPTION: Superior coverage, quality acrylic resin and easy application makes Powafix 1 st Kote the right choice when painting walls and ceilings. You can be assured that when
More informationdura. fibre CFP adhesive
dura. fibre CFP adhesive TWO COMPONENT EPOXY ADHESIVE/REPAIR COMPOUND DESCRIPTION Two component, solvent free, fine aggregate filled, thixotropic, non-slump, polyamide cured epoxy. USES Repairing and patching
More informationAsphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE
Asphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE TABLE OF CONTENT About RESISTO 2 Asphalt Cleaner and Degreaser 3 Oil Spot Primer 3 Liquid Crack Filler 4 Rubberized Crack Filler 4 Levelling
More informationPlaster systems. Plaster systems.
Plaster systems Plaster systems Gyproc plasters have been formulated to suit a wide variety of background types including concrete, brick, blockwork, sand / cement, Gyproc Plasterboards and expanded metal
More informationSITE HANDBOOK. Repair of Concrete Structures. - Patch Repair and Spray Applications
SITE HANDBOOK Repair of Concrete Structures - Patch Repair and Spray Applications A simple step by step guide to preparing and applying Sika Concrete Repair Systems SITE HANDBOOK - Patch Repair and Spray
More informationWater resistant bonding agent and mortar additive
Product Data Sheet Edition 2011-10_1 Water resistant bonding agent and mortar additive Construction Product Description is a modified Styrene Butadiene Emulsion to be mixed with cement (neat) or cement
More informationPlaster systems. High quality lining solutions providing the perfect finish for your walls
C07 Linings High quality lining solutions providing the perfect finish for your walls All our systems are covered by SpecSure when using genuine Gyproc and Isover products Gyproc plasters offer a full
More informationSILASEC DESCRIPTION FEATURES AND BENEFITS SURFACE PREPARATION
SILASEC WP0001 REVISED: JANUARY 2002 DESCRIPTION Bondall Silasec is a concentrated liquid waterproofing compound designed to be used with Portland type A or type GP cements to form a permanent waterproof
More informationMethod Statement. For RSA Coating Systems Over M Grade Expanded Polystyrene (EPS)
Method Statement For RSA Coating Systems Over M Grade Expanded Polystyrene RSA strongly recommend the use of our full render, texture paint systems over polystyrene substrates. We DO NOT recommend mixing
More informationAQUATITE. Also designed as: Crack/gap filler for masonry and unglazed ceramics Sealants against leaks Repairer for roof cracks and gutters
AQUATITE Revision Date: september 2007 Description Bondall AquaTite is a grey, brushable, waterproofing coating that forms a flexible yet tough, seamless membrane. This single pack product exceeds the
More informationProduct Data Sheet Waterproofing Membrane for Ponds and Water Features Description Uses Suitable Surfaces Additional Uses Specification
Product Data Sheet Pondseal Waterproofing Membrane for Ponds and Water Features Description Pondseal is a polyurethane / acrylic co-polymer, water based coating which when fully cured, forms an impervious,
More informationRapid Re-coat PU Modified Under-tile waterproof membrane.
Product Information Technical Data Sheet - December 2017 Rapid Re-coat PU Modified Under-tile waterproof membrane. DESCRIPTION Crommelin Rapid Re-coat PU Modified is a premium, heavy duty liquid applied
More informationTHERMAL INSULATION SYSTEM
opuscolo Kibitherm_EN.FH10 27-06-2007 20:14 Pagina 1 Contents KIBITHERM: a certified system...page 5 Why insulate with KIBITHERM...page 6 KIBITHERM performance features...page 7 How to apply KIBITHERM...page
More informationEN R4 High Strength High Build Concrete Repair Mortar
Product Data Sheet Edition 28th February 2018 Sika MonoTop-612 N EN 1504-3 R4 High Strength High Build Concrete Repair Mortar Construction Product Description Sika MonoTop-612 N is a cement-based, one
More informationARDEX GUIDE SPECIFICATION ARDEX PANDOMO Wall ARDEX PANDOMO W1 Decorative Wall Finishing Compound
ARDEX GUIDE SPECIFICATION ARDEX PANDOMO Wall ARDEX PANDOMO W1 Decorative Wall Finishing Compound SECTION 09 24 16 ARDEX PANDOMO Wall System PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions
More informationDULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS
TECHNICAL DATA SHEET Version 1 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A low odour premium quality interior mid sheen finish with supreme stain resistance. PRODUCT
More informationSIDER-POOL. Product Data. Features and Uses
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 sales@sider-crete.com www.sider-crete.com Product Data Features and Uses A true cement-based plaster No-check cracking and no-brushing
More informationPEKAY T570 RUBBERSEAL
PEKAY T570 RUBBERSEAL DESCRIPTION Pekay Rubberseal T570 is a rubber-latex modified anionic bitumen emulsion, which dries to a pliable, flexible, waterproof, black coating. It may be used for a variety
More informationCaparol System PRO Data sheet
System features Expanded polystyrene insulation Cost effective solution Excellent detailing options Proven technology Wide variety of colours Reliable protection and crack resistance Proven track record
More informationNu-Render Tilt Slab & Off Form Concrete Finish
General Consent Document Nu-Render Tilt Slab & Off Form Concrete Finish March 2010 WATTYL (NZ) LTD Paintworks Specification GS 425.1NZ Page 1 of 1 August 2005 System Substrate Category Grano Sponge Finish
More information1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU.
1. Rapid Set Cement 2. Methods of preparation 3. How to stage a job site 4. Installation Mix, place, finish 5. Coloring the TRU natural TRU Rapid Set is NOT Portland Cement Rapid Set is a Calcium Sulfoaluminate
More informationIntercrete 4802 Application Guidelines
4802_UK Intercrete 4802 Page 1 of 5 Intercrete 4802 Application Guidelines Prepared by: M&PC Technical Operations International Paint Ltd. www.international-pc.com These guidance notes are intended to
More informationRLA CERAMIC TILE ADHESIVE 10 year Limited Warranty
RLA CERAMIC TILE ADHESIVE 10 year Limited Warranty RLA Polymers Pty Ltd; undertakes to warranty Resinflex (or RLA Flex 2- Part), and RLA Flex 1-Part, when used to install tiles over Protectowrap AFM for
More informationTECHNICAL DATA SHEET AUS-CRETE MPA
MULTI-PURPOSE ADHESIVE WALLS AND FLOORS DOMESTIC AND COMMERCIAL TILE AND STONE SUITABLE FOR: LARGE TILE AND STONE ALL MASONRY SURFACES MARBLE AND GRANITE RENDER, BRICK AND BLOCK WORK PORCELAIN CEMENT SHEET
More informationConstruction. Sikadur 35, Hi-Mod LV. Application Instructions. Sika Corporation
Sikadur 35, Hi-Mod LV Application Instructions Sikadur 35, Hi-Mod LV Structural epoxy adhesive Multi-purpose Two-component 100% solids Low viscosity Moisture-tolerant High strength Sikadur 35, Hi-Mod LV
More informationTECHNICAL DATA SHEET AUS-BOND INDUSTRIAL LATEX ADMIX
Description: Aus-Bond Industrial Latex Admix is a specially formulated latex admix for use in sand/cement based mortars for extreme conditions such as swimming pools, facades, rapid transit stations and
More informationTECHNICAL DATA SHEET AUS-MAXIGRIP TEN YEAR WARRANTY AUSTRALIAN STANDARS COMPLIANCE C2 T S1 LOW VOC GREEN FOOTPRINT
Description: Aus-MaxiGrip: Provides a high performance flexible polymer fortified adhesive with excellent slip resentence that is used for installing a wide range of tile and stone, made from lightweight
More informationConcrete Wall & Floor Finishes
TM Concrete Wall & Floor Finishes Interior & Exterior Concrete Wall Finishes / Interior Concrete Floor Finishes ENVIRONMENTALLY Exposed decorative concrete wall and floor finishes Content Introduction
More informationSetting holding down bolts Floor screeds Bedding blocks Stone and bricks In contact with potable water Fine moulding.
PRODUCT SHEET NATCEM 35 Description NATCEM 35 is a fast setting and fast curing mortar with a rapid strength gain that is resistant to chloride penetration, consisting of a blend of NATCEM Potable Water
More informationDUAL EXPANSION. facilitate casting and ensure the total filling of voids even in tight or complex spaces and when working on large surfaces.
Fluid expansive mortar for precision anchoring of machinery and structural elements LAYER THICKNESS FROM 1 TO 10 CM REFURBISHMENT and PROTECTION Line Expansive cement-based mortar for anchoring and grouting
More informationMendrend - Patent No / Uses Stain/Efflorescence Obliteration Example 1: Comrend W.P. Spatter Finish
Mendrend - Patent No. 2372253 / Uses Stain/Efflorescence Obliteration Example 1: Comrend W.P. Spatter Finish The building below had been faced in Comrend W.P. spatter finish. Two to three months after
More informationTECHNICAL BULLETIN TB102
TECHNICAL BULLETIN TB102 TB102.010 Ardex Australia 2004-2014 Deep Filling and of Subfloors With Ardex Floor Levelling Cements Date, Thursday, 11 September 2014 INTRODUCTION & SCOPE Floor levelling cements
More informationPolymer bonding aid and mortar additive bonding agent for old and new concrete. Test method Typical result Control. Compressive strength (BS6319,Pt2)
Techno Bond SBR Polymer bonding aid and mortar additive bonding agent for old and new concrete Uses For improving the physical properties of cementations mixes. Typical uses include, but are not limited
More informationShower Waterproofing Membrane Under tile and wet area waterproofing membrane.
Product Information Technical Data Sheet - December 2017 Shower Waterproofing Membrane Under tile and wet area waterproofing membrane. DESCRIPTION Crommelin Shower Waterproofing Membrane is a waterbased,
More informationDATA SHEET DEKSTER 131 SELFLEVELLING FLOOR COAT / UNDERLAY
(Page 1 of 8 ) GENERAL DESCRIPTION - Dekster 131 self levelling is a contemporary coating that achieves hard wearing, utilitarian floor surfaces in a range of natural tones to offset any style of interior.
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. RobinsonBrick.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide RobinsonBrick.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More informationConstruction. R4 Low Resistivity Dry Sprayed Repair Concrete. Product Description. Product Data. Tests. Form. Storage
Product Data Sheet Edition 08/12/2016 Identification no: 020302030030000029 SikaCem -133CP Gunite SikaCem -133CP Gunite R4 Low Resistivity Dry Sprayed Repair Concrete Construction Product Description Uses
More informationTECHNICAL DATA SHEET SIKADUR 31 CF NORMAL 6KG
TECHNICAL DATA SHEET SIKADUR 31 CF NORMAL 6KG Sikadur 31 is a two component solvent-free, cold cure, thixotropic epoxy adhesive suitable for damp and dry substrates. Available in two grades - Normal and
More informationARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound
ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE
More information3-component epoxy self-smoothing screed
Construction Product Data Sheet Edition 26/07/2016 Identification no: 01 08 01 02 050 0 000017 3-component epoxy self-smoothing screed Product Description Uses Characteristics / Advantages Product Data
More informationData sheet Armatop MP / Page 1
Data sheet Armatop MP / Page 1 Armatop MP Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of ecomin-por, mineral wool, polystyrene and cork exterior
More informationPlastCoat PC 15. The compact one. Interior and exterior plaster spraying with easy to use technology.
PlastCoat PC 15 The compact one Interior and exterior plaster spraying with easy to use technology. With their plaster spraying units Wagner have made it easier to get into the machine-assisted application
More informationPORTER S ORIGINAL LIME WASH
Product Specification Product Name: PORTER S ORIGINAL LIME WASH PRODUCT DESCRIPTION: ENVIRONMENTAL INFORMATION: is a unique lime based coating blended with natural pigments which is designed to create
More informationPRODUCT SELECTION GUIDE
PRODUCT SELECTION GUIDE Floor Sealers MasterTop 333 MasterKure 402 MasterKure 404 MasterTop 1116 Mastertop TC 406 Mastertop TC 450 Mastertop TC 471 Mastertop TC 495 Single Pack Two-pack Epoxy Polyurethane
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More informationReady-to-use structural plaster for interior use
Ready-to-use structural plaster for interior use Very easy to spread Very robust and hard-wearing surface Uniform Fibre-reinforced, low-stress Easy and flexible to handle Environmentally friendly, low-odour
More informationProduct Data Sheet Sikadur -31 CF Normal Product Description Uses ruction Const Characteristics / Advantages
Construction Product Data Sheet Edition 02/12/2013 Identification no: 02 04 02 03 001 0 000039 Sikadur -31 CF Normal 2-part thixotropic epoxy adhesive Product Description Uses Characteristics / Advantages
More informationTEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING
SECTION 09960 - TEXTURED COATINGS Coating System Submittals Guide Specification TEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING (SPLIT FACE OR SAND FINISH BLOCK) 1. TEX COTE 600, Textured Coating
More informationTECHNICAL DATA SHEET. Description
TECHNICAL DATA SHEET System Product MicroCemento Description MicroCemento Alisado is a coloured cementitious layer, 1-2 mm thick. It allows for the renovation of existing floors, such as ceramic tiles,
More informationCrystoflex Max comprising of a liquid component of selected polymers and a powder component of selected cements, fillers and aggregates.
Product Data Sheet Crystoflex Max Two pack, flexible, cementitious waterproofing membrane for positive or negative water pressure. Description Crystoflex Max is a two pack, flexible, cementitious waterproof
More informationWaterproofing and Damp-proofing Cementitious Slurry
Product Data Sheet Edition: 01/10/2012 Identification no. Version no: GCC SikaTop Seal-107 SikaTop Seal-107 Waterproofing and Damp-proofing Cementitious Slurry Product Description Uses SikaTop Seal-107
More informationPOWERBASE ICF / SIDER PROOF FF-PR
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 www.sider-crete.com Designer & Manufacturer of the original Roll-On Pool Plaster! POWERBASE ICF / SIDER PROOF FF-PR Product Data Features
More informationMADA FRENCH ADHESIVE MADE IN KSA. Member of
Member of Mada French Adhesive FEATURES Do you need to finish a wall as quickly as possible? Do you have a rough base surface and want to achieve a smooth final surface finish? TRY THE LATEST INNOVATION
More informationDESCRIPTION FEATURES AND BENEFITS AREAS OF USE. Showers & Bathrooms. Balconies & Patios SUITABLE SUBSTRATES. for application on: Concrete & Masonry
Product Information Technical Data Sheet - August 2017 High Performance DESCRIPTION Crommelin High Performance Under-tile Waterproof Membrane is an exceptionally flexible, 2 part cementitious, positive
More informationEPILOX EPOXY BINDER TECHNICAL DATA SHEET. Multi-purpose High Performance Epoxy Binder System DESCRIPTION FEATURES AND BENEFITS
EPILOX EPOXY BINDER Multi-purpose High Performance Epoxy Binder System DESCRIPTION Aftek Epilox Epoxy Binder is a two part solvent free epoxy resin binder system for combining with selected fillers and
More informationDULUX WEATHERGUARD FINE TEXTURED
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A tough, durable exterior coating with Maxiflex that provides lasting elasticity to cover hairline
More informationSelf Adhesive EPDM TRAINING MANUAL
Self Adhesive EPDM TRAINING MANUAL Rubber4Roofs Ltd, Unit 4 Kingswood Close Page 1 of 7 Copyright Rubber4Roofs Ltd GeneralHealth&Safety Extreme care must be exercised when working on ladders, roofs, below
More informationDATE: 3 rd March 2015
DATE: 3 rd March 2015 PROJECT NAME: Magnesium Oxide Board- External specification PREPARED BY: Chris Suter 0414181066 csuter@ppg.com Armawall Armashield on Magnesium Oxide Board with Preprite Traditional
More informationOne Meter Internal Dome Oven AVERAGE GUIDE
FIELD FURNACE REFRACTORIES Pty Ltd. 8 Arnott Place Wetherill Park NSW 2164 Phone: 02-9729-1799 Fax: 02-9729-1899 One Meter Internal Dome Oven AVERAGE GUIDE Quantity Description Unit price Total 192 Tapered
More informationDATE: 28 th September 2016
DATE: 28 th September 2016 PREPARED BY: Chris Suter 0414181066 csuter@ppg.com PAINTING SCHEDULE Specification for Eco-Easy Magnesium Oxide Board Created by Chris Suter INTERIOR PAINTING SPECIFICATION TAUBMANS
More informationInstallation Instructions Tuscan Field Applied Limestone Finish
Installation Instructions Tuscan Field Applied Limestone Finish TS-107 Recommended Tools for Installation of Tuscan StoneWorx Finishes Variable Speed Drill capable of producing 1000 RPM s MX1 Mixing Paddle
More informationHOW TO: FINISH AND REPAIR INTERNAL WALLS GTEC FINISHING PROFESSIONAL RANGE OF WALL FINISHING AND REPAIR SOLUTIONS
HOW TO: FINISH AND REPAIR INTERNAL WALLS PROFESSIONAL RANGE OF WALL FINISHING AND REPAIR SOLUTIONS GTEC FINISHING 1 PROFESSIONAL RANGE OF WALL FINISHING AND REPAIR SOLUTIONS This How To Guide provides
More informationPROJECT NAME: PROJECT ADDRESS: Farmers Market Structural Repairs 4-6 Gordon Street Guelph, Ontario DATE: November, 2010 I N D E X Page(s) Index... 1 to 1 Introduction... 1 to 1 DIVISION 04 - MASONRY Section
More informationCementitious Concrete Repair Mortar
Product Data Sheet Edition 08/05/2012 Identification no: 02 03 02 04 005 0 000009 SikaTop -122 Cementitious Concrete Repair Mortar Construction Product Description SikaTop -122 is a two component polymer
More informationTechnical Data Sheet. Ultralevel Bulkout. Self Levelling High Build Cementitious Underlay
Technical Data Sheet Ultralevel Bulkout Self Levelling High Build Cementitious Underlay SMF26a 03.07.13 DESCRIPTION Bostik Ultralevel Bulkout is a high build, rapid hardening self levelling polymer modified
More informationConstruction. SikaRepair 223. Application Instructions. Sika Corporation
SikaRepair 223 Application Instructions SikaRepair 223 One-component Early strength gaining Cementitious Patching material for vertical and overhead repair of concrete Where to use: SikaRepair 223 On grade,
More informationConstruction. SikaRepair 223. Application Instructions. Sika Corporation
SikaRepair 223 Application Instructions SikaRepair 223 One-component Early strength gaining Cementitious Patching material for vertical and overhead repair of concrete SikaRepair 223 Where to use: On grade,
More informationMITHOS LUX is a traditional self-polishing Venetian lime putty-base stucco for interiors
MITHOS LUX Product data sheet: VID455150T Rev. 02 dated 06/09/2018 Name Description Product characteristics VOC Classification (Volatile organic compounds) Directive 2004/42/EC MITHOS LUX Traditional Venetian
More information