MODEL SS/SSD/SSID SUBMITTAL RECORD

Transcription

1 MODEL SS/SSD/SSID SUBMITTAL RECORD Single Wall or Double Wall AL29-4C Special Gas Vent for Category I, II, III and IV TYPE L VENT Low temperature venting system INTERNATIONAL, INC. 4 to 24 Diameter Vent For use on Positive, Neutral and Negative Pressures up to 35 W.C. Also for venting listed gas or oil fired appliances listed for venting with TYPE L low temperature venting system (SSD / SSID ONLY) PREPARED FOR: REFERENCE: LOCATION: CONTACT: TELEPHONE: PREPARED BY: MODEL SS MODEL SSID SUBMITTAL RECORD FAX: MODEL SSD SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Listed to standards: UL-1738 ULC-S636 UL-641 } SSD / SSID ONLY ULC-S609 Report # G MTL-006 SFSSAERCO REV. 1 03/2013 MODEL Secure Seal SS/SSD/SSID This installation manual will enable you to obtain a safe, efficient and dependable installation of this vent system. Please read and understand these instructions before beginning your installation. Do not alter or modify the components of this chimney system under any circumstances. Any modification or alteration of the vent system or approved accessories, including but not limited to the appliance it is connected to, may void the warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation. A. Examine all components for possible shipping damage prior to installation; B. Proper joint assembly is essential for a safe installation. Follow these instructions exactly as written: Check severeness of joints upon completion of assembly; C. This venting system must be free to expand and contract. This venting system must be supported in accordance with these instructions; D. Check for unrestricted vent movement through walls, ceilings, and roof penetrations; E. Different manufacturers have different joint systems and adhesives. Do not mix pipe, fittings, or joining methods from different manufacturers. WARNING FAILURE TO FOLLOW THESE INSTALLATION INSTRUCTIONS COULD CAUSE FIRE, CARBON MONOXIDE POISONING, OR DEATH. IF YOU ARE UNSURE OF INSTALLATION REQUIREMENTS, CALL THE PHONE NUMBER LISTED ON THE BACK OF THESE INSTRUCTIONS. A MAJOR CAUSE OF CHIMNEY RELATED FIRE IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS VENT SYSTEM BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.

2 TABLE OF CONTENTS Introduction... page 2 Testing / listing information... page 2 Clearances to combustibles... page 3 General installation requirements... page 3 Typical installations... page 4-5 Chimney and fitting joint assembly... page 6 Chimney weight... page 6 Support methods and height... page 7 Horizontal installation requirements... page 8 Maintain proper slope... page 9 Vertical installation requirements... page 9 Wall penetration... page 10 Roof / floor penetration... page 10 Condensate drains... page 10 Secure Seal as a liner... page 12 Adjustable length... page 13 Maintenance instructions... page 13 Secure Seal Labels... page 14 Warranty... page 40 Product reference information... page 42 INTRODUCTION Secure Seal single wall (SS) or double wall (SSD) or double wall insulated (SSID) is a special stainless steel vent system for gas fired appliances listed as Category I, II, III, and IV or in Canada as Type BH Gas Venting as noted in ULC-636, with a maximum operating temperature of 550 Degrees F (288 Degrees C), and a maximum rated positive pressure of 35 Water Column. It can also vent listed gas or oil fired appliance rated to be vent with TYPE L low temperature venting system (SSD & SSID only). Secure Seal must be installed by an experienced professional familiar with the operation and maintenance of heating appliances and venting. Before installing this product, examine all components for possible shipping damage and read the complete installation manual. Failure to follow proper installation procedures, including vent pitch and improper appliance connections, may cause unsafe conditions. Security Chimneys International Limited recommends the system to be inspected once a year by a qualified service technician TESTING / LISTING INFORMATION Security Chimney International, Ltd. Secure Seal model SS, SSD and SSID venting system is listed with Intertek Testing Services (ETL) to UL/ULC standards: U.S.A. UL-1738 Special Gas Vent for Category I, II, III and IV appliances UL-641 (SSD & SSID only) TYPE L VENT venting listed gas or oil burning appliances CANADA ULC-S636 Type BH Gas Vent Class I/II ULC-S609 (SSD & SSID only) TYPE L VENT venting of flue gases with temperature not exceeding 300 C from oil or gas burning appliances This product must be installed in accordance with local building code requirements as well as National codes: USA - National Fuel Gas code ANSI-Z223.1 or NFPA Standard 54, or NFPA 211. In CANADA - CAN/ CGA-B149.1 or CAN/CGA-B149.2 Propane Installation Code as applicable. Note : - AERCO guide requirements supercede the requirements in this instruction unless dictated by regulatory requirements applicable to the installation site. Esteem 399 : Instruction No. GF-125V Modulex : Instruction No. GF-115-V Innovation : Instruction No. GF-5050 Benchmark : Instruction No. GF The AERCO Benchmark & Innovation products may be common vented but not installed with any other appliances. - The AERCO Modulex products may be common vented but not installed with any other appliances. - The AERCO Esteem products may be common vented but not installed with any other appliances. 2

3 CLEARANCES to combustibles Table 1 shows the required MINIMUM AIRSPACE CLEARANCE TO COM- BUSTIBLES. Combustibles include framing lumber, drywall, plywood, paneling, insulation, wiring and other building materials. Diameter 4 to to 24 Minimum Clearance to Combustibles Single Wall SS Rated operating temperature 480º F (250º C) 480º F (250º C) Max. operating temperature 550º F (288º C) 550º F (288º C) Enclosed (4 sides) Unenclosed (2 sides Max.) Horiz. Vert. Horiz. Vert. N/A N/A 2 2 N/A N/A 4 4 Minimum Clearance to Combustibles Double Wall SSD / SSID Diameter 4 to to 24 4 to 12 L-VENT 14 to 24 L-VENT Rated operating temperature 480º F (250º C) 480º F (250º C) 480º F (250º C) 480º F (250º C) Max. operating temperature 550º F (288º C) 550º F (288º C) 550º F (288º C) 550º F (288º C) Enclosed (4 sides) Table 1 - Minimum Clearances for Secure Seal Unenclosed (2 sides Max.) Horiz. Vert. Horiz. Vert. N/A N/A N/A N/A Auxiliary parts such as combination Roof Supports, Roof Thimble, Flashings and Wall Thimble outer shields are intended to be attached directly to the framing or to ceilings, floors, or walls in accordance with their respective instructions. These parts, which are installed in contact with wood or other combustibles, are designed and tested to assure that they do not overheat at points of contact. GENERAL INSTALLATION REQUIREMENTS When venting Category I, II, III, or IV appliances or TYPE L vented appliance, Secure Seal must be used for the entire length of the system. Do not mix pipe, fittings, or joining methods from different manufacturers. See the Secure Seal catalog for a complete list of parts and products. Every vent system must be planned and installed for optimum performance and safety. The venting system must be free to expand and contract and must be supported in accordance with these instructions. (Check for unrestricted vent movement through walls, ceilings, and roof penetrations). Refer to the gas appliance manufacturer s instructions to determine venting requirements and limitations with respect to installation and use of the appliance. It is the responsibility of the installer to contact local building and fire officials concerning any installation restrictions and/ or inspection requirements that may apply. Permits may be required before starting an installation...if required by the appliance manufacturer, a Drain Tee Cap must be located as close as possible to the appliance flue outlet. Depending on the arrangement of the vent, more than one drain may be required. Unless a Drain Tee Cap is supplied with the appliance, install a Secure Seal Drain Tee Cap...More than one Category II, III or IV appliance may not be connected into the same vent system, unless the appliance manufacturer specifically approved such a system and the appliance are designed for multiple venting. Cat. II, III or IV appliances MAY NOT be common vented with Cat. I, natural draft appliances. This limitation can be removed if an engineering analysis demonstrates normal and safe operation of appliances...secure Seal must not come in contact with plumbing or electrical systems...maintain rated clearances to combustibles over the entire length of the vent system...secure Seal shall not be routed into, through, or within any vent, such as an existing masonry or factory-built chimney, that is connected to another appliance. Notes: 1. Unenclosed requires at least two sides open. 2. Single Wall (SS) may be enclosed only in non-combustible enclosure. 3. Reduced clearances may be attained by using non-combustible enclosures. 4. Combustible Material is any material made of or surfaced with wood, compressed paper, plant fibers or other materials that are capable of being ignited or burned. Such material shall be considered combustible even though it is flame-proofed, fire-retardant treated, or plastered. (Source: NFPA 54/ANSI Z223.1) 5. Design any enclosure to permit inspection of the system. 6. Do not place insulation in any required clearance spaces surrounding the vent system unless these instructions suggest otherwise and the insulation is specified or supplied. 3

4 TYPICAL INSTALLATION Cables, rods or braces By other 500 lbs rated Minimum slope 1/4 per foot Minimum Clearances See table 1 30º Termination (STA) Opening dimension See table 6 Suspension Band (SB) Maximum distance between support (MHS), see table 5 Roof Support (RS) Wall Thimble (WT/WTI) Anchor Plate HD (APHD) Maximum distance suspended (S), see table 5 Appliance Refer to condensate drain section for proper installation Appliance adaptor Figure 1 - Horizontal 4 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

5 TYPICAL INSTALLATION Exit Cone (EC) Maximum freestanding height See table 5 (H) Guy wires by others 500 lbs rated Flashing (F) Roof support (RS) Maximum distance between guides (MVS) See table 5 Maximum distance between supports See table 4 Opening dimension See table 6 Roof thimble (RT/RTI) Guy Support (GS) Minimum Clearance See table 1 Maximum distance between elbows without any support or guide See table 5 (MDE) Wall support (WS) Maximum distance between supports See table 4 Wall guide (WG) Maximum distance between guides See table 5 (MVS) Wall guide (WG) Appliance adaptor Wall support HD (WSHD) Appliance Figure 2 - Vertical NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 5

6 CHIMNEY AND FITTING JOINT ASSEMBLY All components have a male and female end, the male end has the gasket. The installation orientation is indicated on the labeling of each chimney section with an arrow. The arrow indicated the direction of the flow. Secure Seal SS 1. Add a thin film of silicone lubricant on the o-ring. 2. Insert the male end into the female end. Secure Seal SSD / SSID Table 2 ASSEMBLY JOINT SS/SSD/SSID LUBE REQUIREMENT Inside diameter Qty (oz) CHIMNEY WEIGHT 3.Close the clips to secure the joint. NOTE: Clips are self-locking Figure 3 - Joint assembly steps Pull Up To open clips, push the secondary catch while pulling up the lever Push Figure 4 - Opening clips Chimney weight is given in pounds per foot of each diameter. It is important to know the weight of the chimney section for chimney support or guiding. Chimney weight (table 3) along with the maximum chimney height (table 4) is necessary to calculate the proper anchor strength needed with supports. CHIMNEY WEIGHT IN LB/FT INSIDE DIAMETER SS SSD SSID N/A N/A Table 3 - Chimney weight Example: Model Secure Seal SSD 6 diameter section of 25 feet in length from table 3, weight in lb/ft = 3. Total length 3 x 25 = 75lbs. 6

7 SUPPORT METHODS AND HEIGHT 1...Several support and guiding methods are used to anchor a chimney against upward, downward and angular placement. 2...These supports and guides prevent bending stresses on the chimney elbows and joints. 3...Certain limitations apply for proper installation of supports and guides. See tables 4 and See figure 1 and 2 for typical installations. Inside dia. MAXIMUM CHIMNEY HEIGHTS AND SUPPORT METHOD FOR MODEL SS Anchor Plate (AP) Anchor Plate HD (APHD) Wall Support (WS) Wall Support HD (WSHD) Roof support (RS) Guy support (GS) MAXIMUM CHIMNEY HEIGHTS AND SUPPORT METHOD FOR MODEL SSD Inside dia. Anchor Plate (AP) Anchor Plate HD (APHD) Wall Support (WS) Wall Support HD (WSHD) Roof support (RS) Guy support (GS) Table 4 - Dimensions are in feet MAXIMUM CHIMNEY HEIGHTS AND SUPPORT METHOD FOR MODEL SSID Inside dia. Anchor Plate (AP) Anchor Plate HD (APHD) Wall Support (WS) Wall Support HD (WSHD) Roof support (RS) Guy support (GS) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Table 5 - Dimensions are in feet 7

8 Inside diameter SUPPORT AND GUIDE SPACING FOR MODEL SS Interior MVS Exterior MHS MDE H S Inside diameter SUPPORT AND GUIDE SPACING FOR MODEL SSD & SSID Interior MVS Exterior MHS MDE H S Table 6 - Dimensions are in feet MVS : Maximum Vertical Spacing between Guides/Supports MHS: Maximum Horizontal Spacing between Guides/Supports MDE: Maximum Distance between Elbows H: Maximum Freestanding above the Roof S: Maximum Suspended Length *Important Notes: 1...For Anchor Plate (AP) / Anchor Plate Heavy Duty (APHD) / Wall Support Heavy Duty (WSHD), the support must be installed below a bead. See figure For Wall Support (WS) / Roof Support (RS), the support can be installed anywhere on the part. Bead Anchor plate, Anchor plate HD or Wall support HD 1. Pass the female end through the hole of the one part plate. 2. Install the two parts plate below a bead and bolt it to the one part plate. Figure 5 - Position of support HORIZONTAL INSTALLATION REQUIREMENTS Bead One part plate Two parts plate Bolts and nuts..when venting through a sidewall, terminate the system not less than 12 (.3m) above the ground and above the snow line in geographical areas where snow accumulates. The termination area must be kept clear of snow and ice at all times...terminate the system at least 7 (2.1m) above a public walkway or driveway, no less than 6 (1.8m) from the combustion air intake of any appliance or 3 (.9m) from any other building opening, gas utility meter, service regulator or the like. Less distance is permitted if specified in the appliance s installation instructions. It also shall terminate at least 3 (.9M) above any forced air inlet within 10 (3.1m) and shall terminate at least 4 (1.2m) below, 4 horizontally from, or 1 (.3m) above any door, window, or gravity air inlet into any building as provided in the National Fuel Gas Code ANSI Z223.1 and NFPA 54. See figure 6. Proper judgment may require greater distances depending on the side of the equipment installed or to allow for snow drifting or falling from falling from overhead roofs or trees. The termination should be far enough away from trees, shrubs, or decorative items to prevent damage...the total horizontal vent length from the appliance flue collar to the outside termination shall be in accordance with the appliance manufacturer s instructions. 8 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

9 MAINTAIN PROPER SLOPE..Install with a continuous 1/4 per foot (minimum) slope, as is required by the National Fuel Gas Code for all gas-fired appliances...vent systems for condensing appliances must have a continuous 1/4 per foot (minimum) slope toward the appliance or a condensate drain. Always check the appliance manufacturer s instructions for proper drain requirements...secure Seal offers a range of tees and elbows that are built incorporating a 2 degree slope, we recommend that you use these to generate your slope...some appliances require the venting system to be sloped toward the horizontal termination...remember, if you raise the appliance or lower the ceiling you must adjust the slope of the vent to maintain the 1/4 per foot minimum. 1 ft. above doors and windows 4 ft below any window or fresh air inlet 1 ft. above ground or snow line 4 ft. horizontally from door and windows Figure 6 - Horizontal termination requirements Sidewalk 7 ft above public walkways and drives VERTICAL INSTALLATION REQUIREMENTS 1...The vent system must terminate at least 3 feet above the roof line and at least 2 feet higher than any portion of the building within 10 feet. See figure 7. This limitation can be removed if an engineering analysis demonstrates normal and safe operation of appliance. 2...When terminated at a height of more than 10 feet, the stack must be supported by a Guy Section. 3...The vent system must terminate with one of the Secure Seal terminations. Except; a)..category I appliances (natural draft) must use a Rain Cap. It is optional on Category II. This limitation can be removed if an engineering analysis demonstrates normal and safe operation of appliance. b)..vent systems without provisions for draining rain water must use a Rain Cap. c)..terminations or approved mechanical vent devices specified or provided by the appliance manufacturer are permitted. 4...The total continuous distance of the vent system from the appliance flue collar to the termination shall not exceed that specified in the appliance manufacturer s installation instructions. When venting natural draft appliances the termination must be at least 5 feet above the topmost draft hood. Otherwise a listed mechanical draft inducing device is required. This limitation can be removed if an engineering analysis demonstrates normal and safe operation of appliance. 5...In general, systems installed in cold climates perform best, and condensation is reduced, when the system is fully enclosed by some part of the building structure or by using insulated SSID venting system. 6...In cold climates do not install a condensate drain on the exterior of the building. Doing so may result in dangerous icy conditions on surfaces near the drain and may cause damage to the vent system and/or the building exterior. Security Chimneys will NOT be held liable for any personal injury or property damage due to any formation of ice. 7...Vertical supports are required after every transition to vertical. Vertical supports are also required after every offset elbow. 8...Unless Secure Seal is installed in a fire rated shaft, a roof thimble and support is required when penetration fire rated floors, walls or ceilings ft. above structures within 10 ft. Figure 7 - Vertical installation requirements NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 9

10 WALL PENETRATION 1...Prior to installation, determine proper location of wall thimble (WT) or wall thimble insulated (WTI) so that a minimum slope of 1/4 (6mm) per foot is maintained in the horizontal section of vent to ensure proper flow of condensation. 2...Prepare the wall by cutting a square opening. See table 6 for opening dimension. 3...Install the wall thimble by inserting the larger of the two parts on the appliance (interior side). See figure Next, apply a bead of sealant around the edges of the exterior (smaller of the two parts) wall thimble component. Then install this part of the wall thimble by inserting the smaller collar into the other component from the previous step. NOTE: The two horizontal cylinders of the thimble must engage a minimum of two inches. ROOF / FLOOR PENETRATION 1...A roof thimble (RT) or roof thimble insulated (RTI) for cold climate must be installed every time the vent system passes through a floor or roof. 2...Prepare the roof / floor by cutting a square opening. See table Install the roof thimble. You may cut the radiation sleeve if it is too long. See figure For roof installation, install a flashing. Flashing Air gap or insulated Roof support 5...Fasten both sides of the wall thimble using screws or nails. 6...Once the thimble is installed, Secure Seal vent pipe can be inserted into the thimble. 7...Close the gap between the thimble and the vent by installing the two half plate and fasten it using screws or nails. 8...Install horizontal termination to complete the assembly. 9...Once assembly is completed, apply a bead of high-temp sealant around the pipe and the exterior two half plates of the thimble to protect against weather. 10..The air gap is filled with insulation when using the insulated wall thimble (WTI). Opening dimension See table 6 Figure 9 - Roof penetration Roof thimble 2 Minimum overlap Opening dimension See table 6 Air gap or insulated Figure 8 - Wall penetration Add sealant Two half plate Wall Thimble (WT/WTI) Termination CONDENSATE DRAINS When an internal condensate drain is NOT part of the appliance: 1. A Drain length (DL) or a Tee with a drain tee cap (DTC) is strongly recommended. Install this drain as close as possible to the appliance flue collar A condensate drain is required for every 30 feet of horizontal vent and at the bottom of a vertical stack Use the Drain length for a straight horizontal run. Rotate the fitting so that the drain tube is as vertical as possible Use a Tee at a transition from horizontal to vertical, and attach the Drain Tee Cap to the appropriate branch of the tee A condensate drain tube kit is available to direct the condensate to an appropriate location. A trap loop must be formed into the drain hose and must be a diameter that is at least four times the appliance s rated stack pressure in inches of water column or minimum 3 inches. Secure the loop with a cable tie Flue gas condensate can have a low (3 to 5) PH level, follow all local and national codes and regulations for the draining of acidic condensate In cold climate, do not install a condensate drain on the exterior of the building. Doing so may result in dangerous icy conditions on surfaces near the drain and may cause damage to the vent system and the building exterior. Security Chimneys will NOT be held liable for any injury or property damage due to formation of ice. 10 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

11 Inside diameter OPENING DIMENSIONS FOR WALL/ROOF PENETRATION FOR MODEL SS Wall Thimble (WT) Wall Thimble Insulated (WTI) Roof Thimble (RT) Roof Thimble Insulated (RTI) 4 9x9 10x10 8x8 12x x10 11x11 9x9 13x x11 12x12 10x10 14x x12 13x13 11x11 15x x13 14x14 12x12 16x x14 15x15 13x13 17x x15 16x16 14x14 18x x17 18x18 16x16 20x x22 22x22 22x22 22x x24 24x24 24x24 24x x26 26x26 26x26 26x x28 28x28 28x28 28x x30 30x30 30x30 30x x32 32x32 32x32 32x32 Table 7 - Dimensions are in inches Inside diameter OPENING DIMENSIONS FOR WALL/ROOF PENETRATION FOR MODEL SSID Wall Thimble (WT) Wall Thimble Insulated (WTI) Roof Thimble (RT) Roof Thimble Insulated (RTI) 4 13x13 14x14 10x10 14x x14 15x15 11x11 15x x15 16x16 12x12 16x x16 17x17 13x13 17x x17 18x18 14x14 18x18 9 N/A N/A N/A N/A 10 19x19 20x20 16x16 20x x22 22x22 18x18 22x x24 24x24 20x20 24x x26 26x26 22x22 26x x28 28x28 24x24 28x x30 30x30 26x26 30x x32 32x32 28x28 32x32 24 N/A N/A N/A N/A Table 9 - Dimensions are in inches Inside diameter OPENING DIMENSIONS FOR WALL/ROOF PENETRATION FOR MODEL SSD Wall Thimble (WT) Wall Thimble Insulated (WTI) Roof Thimble (RT) Roof Thimble Insulated (RTI) 4 11x11 12x12 8x8 12x x12 13x13 9x9 13x x13 14x14 10x10 14x x14 15x15 11x11 15x x15 16x16 12x12 16x x16 17x17 13x13 17x x17 18x18 14x14 18x x19 20x20 16x16 20x x22 22x22 18x18 22x x24 24x24 20x20 24x x26 26x26 22x22 26x x28 28x28 24x24 28x x30 30x30 26x26 30x x32 32x32 28x28 32x32 Table 8 - Dimensions are in inches NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 11

12 INSTALLING SECURE SEAL AS A LINER IN A MASONRY CHIMNEY OR AS A LINER IN AN EXISTING VENT * Stainless Steel Wire Rope (by others) is to be used to hang the vent system from the top of the masonry chimney or from the top of the existing vent. - The stainless wire rope is attached to the Guy Support Band and is secured with cable clamps (by others). - The Stainless Steel Wire Rope is secured in a similar manner to the top platform of the masonry chimney or existing vent. - Use the appropriate size of Stainless Steel Wire Rope to accommodate the required total loads of the vent system. It may be necessary to fabricate a platform (at top of chimney / vent - by others). Note: When installed as a liner in a masonry chimney or to reline an existing vent no other appliance can be vented into the same chimney or vent. Masonry chimney Combustible wall Exit cone (EC) 1 Minimum Consult Security Chimneys International for guidelines. DO NOT USE GALVANIZED WIRE ROPE. Stainless steel wire rope * (by other) Centering band (CB) Maximum distance between guides See table 5 (MVS) Maximum distance between supports See table 4 Guy support (GS) Maximum distance between guides See table 5 (MVS) Elbow or tee Figure 10 - Installing Secure Seal as a liner 12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

13 ADJUSTABLE LENGTH For installations that requires non-standard vent lengths, Secure Seal Adjustable Length (AL) should be used. The part consists of an inner conduit that slips into the downstream part and over the upstream part, a collar holds the conduit in place and an outer shell (for double wall only). See figure 11 for installation steps. Note: The inner conduit may be cut to desired length to limit interference with downstream part. Secure Seal SS 1. Keep a play about 1/8 to 1/4 to allow thermal expansion 2. Add a bead of Viton caulking about 1/4 3. Slide the collar down over the female end of the downstream part and tighten the collar ADJUSTABLE LENGTH SS/SSD CAULKING REQUIREMENT Inside diameter Qty (oz) Table 10 MAINTENANCE INSTRUCTIONS Secure Seal SSD 1. Keep a play about 1/8 to 1/4 to allow thermal expansion 2. Add a bead of Viton caulking about 1/4 3. Slide the collar down over the female end of the downstream part and tighten the clamp As with all vents, the Secure Seal vent system should be inspected at least annually for the presence of deposits or debris and any accumulation should be removed. The vent system should also be inspected at regular periods for signs of leakage of condensate or combustion products at any joints. If the vent system incorporates a drain hose from either a Drain length or a Drain tee cap, the hose must be inspected periodically to ensure that water is in the trap loop. If a proper trap loop is not maintained, exhaust from the connected appliances may accumulate in the building area. 4. Install the outer shell over ends of downstream and upstream parts and tighten the clamps. Need to cut outer shell to correct length. Figure 11 - Adjustable length installation steps NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 13

14 SS, SSD / SSID SECURE SEAL CHIMNEY LABELS The labels supplied for product identification are shown here and indicates the flow of the flue gases in the venting system. 14

15 SSD / SSID VENT LENGTHS Effective length Effective length 3-5/8 Effective Length SSD & SSID Lengths SSD SSID 4 to /8 SSDL9UK SSIDL9UK 4 to /8 SSDL12UK SSIDL12UK 4 to /8 SSDL18UK SSIDL18UK 4 to /8 SSDL24UK SSIDL24UK 4 to /8 SSDL36UK SSIDL36UK SSD & SSID Test Port Lengths Effective Length SSD SSID 4 to /8 SSDTPLUK SSIDTPLUK Drain 4 24, 1/4 NPT, 1/2 O.D. Figure 14 Figure 12 Effective length Effective length 3-1/4 SSD & SSID Adjustable Lengths Effective Length SSD SSID 4 to 24 4 to 5 SSDAL9UK SSIDAL9UK 4 to 24 4 to 14 SSDAL18UK SSIDAL18UK 4 to 24 4 to 22 SSDAL24UK SSIDAL24UK 4 to 24 4 to 32 SSDAL36UK SSIDAL36UK Effective Length SSD & SSID Drain Lengths SSD SSID K Factor 4 to /8 SSDDLUK SSIDDLUK 0.25 Drain 4 10, 1/4 NPT, 1/2 O.D. Drain 12 24, 1/2 NPT, 5/8 O.D. Figure 15 Figure 13 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 15

16 SSD & SSID Venting Elbows 2º 15º SSD 2-Degree Elbow SSD K Factor 4 1/8 7-3/4 SSD4E2UK /8 7-3/4 SSD5E2UK /8 7-7/8 SSD6E2UK /8 7-7/8 SSD7E2UK /8 7-7/8 SSD8E2UK /8 8 SSD9E2UK /8 8 SSD10E2UK /8 8 SSD12E2UK /8 8-1/8 SSD14E2UK /8 8-1/4 SSD16E2UK /8 8-1/4 SSD18E2UK /8 8-3/8 SSD20E2UK /8 8-3/8 SSD22E2UK /8 8-1/2 SSD24E2UK.03 Figure 16 SSD 15-Degree Elbow SSD K Factor /4 SSD4E15UK /4 SSD5E15UK /8 9 SSD6E15UK /8 9-3/8 SSD7E15UK /4 9-5/8 SSD8E15UK /4 9-7/8 SSD9E15UK /4 10-1/8 SSD10E15UK /8 10-5/8 SSD12E15UK /8 11-1/8 SSD14E15UK /2 11-5/8 SSD16E15UK /2 12-1/8 SSD18E15UK /8 12-5/8 SSD20E15UK /8 13-1/4 SSD22E15UK /4 13-3/4 SSD24E15UK.26 Figure 18 SSID 2-Degree Elbow SSID K Factor 4 1/8 7-3/4 SSID4E2UK /8 7-3/4 SSID5E2UK /8 7-7/8 SSID6E2UK /8 7-7/8 SSID7E2UK /8 7-7/8 SSID8E2UK.04 9 N/A N/A N/A N/A 10 1/8 8 SSID10E2UK /8 8 SSID12E2UK /8 8-1/8 SSID14E2UK /8 8-1/4 SSID16E2UK /8 8-1/4 SSID18E2UK /8 8-3/8 SSID20E2UK /4 8-3/8 SSID22E2UK N/A N/A N/A N/A Figure 17 SSID 15-Degree Elbow SSID K Factor 4 1-1/8 9 SSID4E15UK /8 9-3/8 SSID5E15UK /4 9-5/8 SSID6E15UK /4 9-7/8 SSID7E15UK /4 10-1/8 SSID8E15UK.29 9 N/A N/A N/A N/A /8 10-5/8 SSID10E15UK /8 11-1/8 SSID12E15UK /2 11-5/8 SSID14E15UK /2 12-1/8 SSID16E15UK /8 12-5/8 SSID18E15UK /8 13-1/4 SSID20E15UK /4 13-3/4 SSID22E15UK N/A N/A N/A N/A Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

17 30º 45º SSD 30-Degree Elbow SSD K Factor 4 2-3/8 9-5/8 SSD4E30UK /8 9-5/8 SSD5E30UK /8 10-1/8 SSD6E30UK /4 10-5/8 SSD7E30UK /8 11-1/8 SSD8E30UK /8 SSD9E30UK /8 12-1/8 SSD10E30UK /8 13-1/8 SSD12E30UK /8 14-1/8 SSD14E30UK /8 15-1/8 SSD16E30UK /8 16-1/8 SSD18E30UK /2 17-1/8 SSD20E30UK /4 18-1/8 SSD22E30UK /8 SSD24E30UK.51 Figure 20 SSID 30-Degree Elbow SSID K Factor 4 2-5/8 10-1/8 SSID4E30UK /4 10-5/8 SSID5E30UK /8 11-1/8 SSID6E30UK /8 SSID7E30UK /8 12-1/8 SSID8E30UK N/A N/A N/A N/A /8 13-1/8 SSID10E30UK /8 14-1/8 SSID12E30UK /8 15-1/8 SSID14E30UK /8 16-1/8 SSID16E30UK /2 17-1/8 SSID18E30UK /4 18-1/8 SSID20E30UK /8 SSID22E30UK N/A N/A N/A N/A Figure 21 SSD 45-Degree Elbow SSD K Factor /8 SSD4E45UK /8 SSD5E45UK /4 10-7/8 SSD6E45UK /2 11-1/2 SSD7E45UK /8 12-1/4 SSD8E45UK /8 13 SSD9E45UK /8 13-5/8 SSD10E45UK /8 SSD12E45UK /8 16-1/2 SSD14E45UK /8 17-7/8 SSD16E45UK /4 19-3/8 SSD18E45UK /8 20-3/4 SSD20E45UK /8 22-1/8 SSD22E45UK /2 23-5/8 SSD24E45UK.08 Figure 22 SSID 45-Degree Elbow SSID K Factor 4 4-1/4 10-7/8 SSID4E45UK /2 11-1/2 SSID5E45UK /8 12-1/4 SSID6E45UK /8 13 SSID7E45UK /8 13-5/8 SSID8E45UK N/A N/A N/A N/A /8 SSID10E45UK /8 16-1/2 SSID12E45UK /8 17-7/8 SSID14E45UK /4 19-3/8 SSID16E45UK /8 20-3/4 SSID18E45UK /8 22-1/8 SSID20E45UK /2 23-5/8 SSID22E45UK N/A N/A N/A N/A Figure 23 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 17

18 88º 90º SSD 88-Degree Elbow SSD K Factor /4 SSD4E88UK /4 SSD5E88UK /4 10-1/4 SSD6E88UK /4 11-1/4 SSD7E88UK /4 12-1/4 SSD8E88UK /4 13-1/4 SSD9E88UK /8 14-1/4 SSD10E88UK /8 16-1/4 SSD12E88UK /4 SSD14E88UK /4 SSD16E88UK /8 22-1/4 SSD18E88UK /8 24-1/4 SSD20E88UK /4 26-1/4 SSD22E88UK /8 28-1/4 SSD24E88UK.20 Figure 24 SSID 88-Degree Elbow SSID K Factor 4 9-1/4 10-1/4 SSID4E88UK /4 11-1/4 SSID5E88UK /4 12-1/4 SSID6E88UK /4 13-1/4 SSID7E88UK /8 14-1/4 SSID8E88UK N/A N/A N/A N/A /8 16-1/4 SSID10E88UK /4 SSID12E88UK /4 SSID14E88UK /8 22-1/4 SSID16E88UK /8 24-1/4 SSID18E88UK /4 26-1/4 SSID20E88UK /8 28-1/4 SSID22E88UK N/A N/A N/A N/A Figure 25 SSD 90-Degree Elbow SSD K Factor 4 8-1/2 9-1/8 SSD4E90UK /2 9-1/8 SSD5E90UK /2 10-1/8 SSD6E90UK /2 11-1/8 SSD7E90UK /2 12-1/8 SSD8E90UK /2 13-1/8 SSD9E90UK /2 14-1/8 SSD10E90UK /2 16-1/8 SSD12E90UK /2 18-1/8 SSD14E90UK /2 20-1/8 SSD16E90UK /2 22-1/8 SSD18E90UK /2 24-1/8 SSD20E90UK /2 26-1/8 SSD22E90UK /2 28-1/8 SSD24E90UK.20 Figure 26 SSID 90-Degree Elbow SSID K Factor 4 9-1/2 10-1/8 SSID4E90UK /2 11-1/8 SSID5E90UK /2 12-1/8 SSID6E90UK /2 13-1/8 SSID7E90UK /2 14-1/8 SSID8E90UK.37 9 N/A N/A N/A N/A /2 16-1/8 SSID10E90UK /2 18-1/8 SSID12E90UK /2 20-1/8 SSID14E90UK /2 22-1/8 SSID16E90UK /2 24-1/8 SSID18E90UK /2 26-1/8 SSID20E90UK /2 28-1/8 SSID22E90UK N/A N/A N/A N/A Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

19 SSD & SSID Venting Tees 43º 45º SSD 43-Degree Tee K Factor /2 8-1/4 13-3/8 SSD4T43UK /2 8-7/8 14-3/8 SSD5T43UK /2 9-5/8 15-3/8 SSD6T43UK /2 10-1/4 16-1/4 SSD7T43UK /2 11-5/8 18 SSD8T43UK /2 12-1/4 18-7/8 SSD9T43UK / /4 SSD10T43UK / /8 SSD12T43UK /2 16-3/8 24-1/4 SSD14T43UK /2 18-1/2 26-1/4 SSD16T43UK /4 20-1/2 29-3/8 SSD18T43UK /4 23-7/8 33-1/2 SSD20T43UK /4 23-7/8 33-7/8 SSD22T43UK /4 27-7/8 38-1/2 SSD24T43UK 0.4 Available with smaller snout and custom height. Figure 28 SSID 43-Degree Tee K Factor /2 9-5/8 15-3/8 SSID4T43UK /2 10-1/4 16-1/4 SSID5T43UK /2 11-5/8 18 SSID6T43UK /2 12-1/4 18-7/8 SSID7T43UK / /4 SSID8T43UK N/A N/A N/A N/A N/A / /8 SSID10T43UK /2 16-3/8 24-1/4 SSID12T43UK /2 18-1/2 26-1/4 SSID14T43UK /4 20-1/2 29-3/8 SSID16T43UK /4 23-7/8 33-1/2 SSID18T43UK /4 23-7/8 33-7/8 SSID20T43UK /4 27-7/8 38-1/2 SSID22T43UK N/A N/A N/A N/A N/A Available with smaller snout and custom height. Figure 29 SSD 45-Degree Tee K Factor /2 8-1/4 13-1/4 SSD4T45UK /2 9-1/4 14-1/8 SSD5T45UK /2 9-7/8 15-1/8 SSD6T45UK /2 10-5/8 16 SSD7T45UK / /8 SSD8T45UK /2 12-3/4 18-1/2 SSD9T45UK /2 13-1/2 19-1/2 SSD10T45UK /2 15-5/8 22 SSD12T45UK / /8 SSD14T45UK /2 19-1/8 26-3/8 SSD16T45UK /4 21-1/4 28-7/8 SSD18T45UK /4 24-3/4 32-7/8 SSD20T45UK /4 24-3/4 33-1/4 SSD22T45UK /4 28-7/8 37-3/4 SSD24T45UK.04 Available with smaller snout and custom height. Figure 30 SSID 45-Degree Tee K Factor /2 9-7/8 15-1/8 SSID4T45UK /2 10-5/8 16 SSID5T45UK / /8 SSID6T45UK /2 12-3/4 18-1/2 SSID7T45UK /2 13-1/2 19-1/2 SSID8T45UK.04 9 N/A N/A N/A N/A N/A /2 15-5/8 22 SSID10T45UK / /8 SSID12T45UK /2 19-1/8 26-3/8 SSID14T45UK /4 21-1/4 28-7/8 SSID16T45UK /4 24-3/4 32-7/8 SSID18T45UK /4 24-3/4 33-1/4 SSID20T45UK /4 28-7/8 37-3/4 SSID22T45UK N/A N/A N/A N/A N/A Available with smaller snout and custom height. Figure 31 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 19

20 4 to 8 9 to 24 SSD Lateral Secure Tee K Factor /8 11-5/8 10 SSD4BTUK /8 12-1/4 11 SSD5BTUK /8 13-3/4 12-1/4 SSD6BTUK /8 14-3/4 13-1/4 SSD7BTUK / /8 SSD8BTUK /8 14-1/4 14-1/4 SSD9BTUK /8 15-1/4 15-1/4 SSD10BTUK /8 16-7/8 17 SSD12BTUK /8 18-7/8 18-7/8 SSD14BTUK /8 20-3/4 20-3/4 SSD16BTUK /8 22-1/2 22-1/2 SSD18BTUK /8 24-3/8 24-3/8 SSD20BTUK /8 26-1/4 26-1/4 SSD22BTUK / /8 SSD24BTUK 0.55 Available with smaller snout and custom height. Figure 32 4 to 8 9 to 24 SSD Lateral Secure Tee 88-Degree K Factor /8 11-5/8 10-1/4 SSD4BT88UK /8 12-1/4 11-3/8 SSD5BT88UK /2 13-3/4 12-3/4 SSD6BT88UK /8 14-7/8 13-3/4 SSD7BT88UK /8 16-1/8 15 SSD8BT88UK /8 14-1/2 15-1/4 SSD9BT88UK /8 15-3/8 16-1/8 SSD10BT88UK / /8 SSD12BT88UK /8 19-1/8 20-1/8 SSD14BT88UK / SSD16BT88UK /8 22-7/8 24 SSD18BT88UK /8 24-3/4 26 SSD20BT88UK /8 26-5/8 28 SSD22BT88UK /8 28-1/2 29-7/8 SSD24BT88UK 0.55 Available with smaller snout and custom height. Figure 34 SSID Lateral Secure Tee K Factor /8 13-3/4 12-1/4 SSID4BTUK /8 14-3/4 13-1/4 SSID5BTUK / /8 SSID6BTUK /8 14-1/4 14-1/4 SSID7BTUK /8 15-1/4 15-1/4 SSID8BTUK N/A N/A N/A N/A N/A /8 16-7/8 17 SSID10BTUK /8 18-7/8 18-7/8 SSID12BTUK /8 20-3/4 20-3/4 SSID14BTUK /8 22-1/2 22-1/2 SSID16BTUK /8 24-3/4 24-3/8 SSID18BTUK /8 26-1/4 26-1/4 SSID20BTUK / /8 SSID22BTUK N/A N/A N/A N/A N/A Available with smaller snout and custom height. SSID Lateral Secure Tee 88-Degree K Factor /2 13-3/4 12-3/4 SSID4BT88UK /8 14-7/8 13-3/4 SSID5BT88UK /8 16-1/8 15 SSID6BT88UK /8 14-1/2 15-1/4 SSID7BT88UK /8 15-3/8 16-1/8 SSID8BT88UK N/A N/A N/A N/A N/A / /8 SSID10BT88UK /8 19-1/8 20-1/8 SSID12BT88UK / SSID14BT88UK /8 22-7/8 24 SSID16BT88UK /8 24-3/4 26 SSID18BT88UK /8 26-5/8 28 SSID20BT88UK /8 28-1/2 29-7/8 SSID22BT88UK N/A N/A N/A N/A N/A Available with smaller snout and custom height. Figure 33 Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

21 SSD & SSID Venting Tees B 4-1/8 SSD & SSID Tee Cap SSD SSID 4 to /8 SSDTCUK SSIDTCUK Figure /4 B Available SSD & SSID Eccentric Tapered Increaser SSD SSID K Factor 4 to /2 1/2 SSDETIN(B)UK SSIDETIN(B)UK to /2 1 SSDETIN(B)UK SSIDETIN(B)UK to /2 1-1/2 SSDETIN(B)UK SSIDETIN(B)UK to /2 2 SSDETIN(B)UK SSIDETIN(B)UK to /2 2-1/2 SSDETIN(B)UK SSIDETIN(B)UK to /2 3 SSDETIN(B)UK SSIDETIN(B)UK 0.30 Figure 39 Drain NPT SSD & SSID Drain Tee Cap SSD SSID 4 to /8 SSDDTCUK SSIDDTCUK Drain 4 10, 1/4 NPT, 1/2 0.D Drain 12 24, 3/8 NPT, 5/8 0.D Figure 37 B SSD & SSID Venting Accessories B Available SSD & SSID Tapered Increaser SSD SSID K Factor 4 to /8 SSDTIN(B)UK SSIDTIN(B)UK to /8 SSDTIN(B)UK SSIDTIN(B)UK to /8 SSDTIN(B)UK SSIDTIN(B)UK to /8 SSDTIN(B)UK SSIDTIN(B)UK to /8 SSDTIN(B)UK SSIDTIN(B)UK to /8 SSDTIN(B)UK SSIDTIN(B)UK 0.30 Figure 38 B B Available SSD & SSID Tapered Reducer SSD SSID K Factor 5 to /16 SSDTRD(B)UK SSIDTRD(B)UK to /16 SSDTRD(B)UK SSIDTRD(B)UK to /16 SSDTRD(B)UK SSIDTRD(B)UK to /16 SSDTRD(B)UK SSIDTRD(B)UK to /16 SSDTRD(B)UK SSIDTRD(B)UK to /16 SSDTRD(B)UK SSIDTRD(B)UK 0.17 Figure 40 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 21

22 SSD & SSID Venting Accessories B SSD + Clearance +9 SSID + Clearance +11 B Available SSD & SSID Eccentric Tapered Reducer SSD SSID K Factor 5 to /2 1/2 SSDETRD(B)UK SSIDETRD(B)UK to /2 1 SSDETRD(B)UK SSIDETRD(B)UK to /2 1-1/2 SSDETRD(B)UK SSIDETRD(B)UK to /2 2 SSDETRD(B)UK SSIDETRD(B)UK to /2 2-1/2 SSDETRD(B)UK SSIDETRD(B)UK to /2 3 SSDETRD(B)UK SSIDETRD(B)UK 0.17 Width SSD & SSID Wall Thimble Insulated Width SSD SSID 4 to 24 9 to 17 SSDWTIH SSIDWTIH Figure 43 Figure SSD + Clearance + 5 SSID + Clearance + 7 SSD + Clearance + 5 SSID + Clearance + 7 SSD & SSID Roof Thimble Width SSD SSID 4 to SSDRTH SSIDRTH Figure 44 Width SSD & SSID Wall Thimble Width SSD SSID 4 to 24 9 to 17 SSDWTH SSIDWTH 10 Figure 42 SSD + Clearance +5 SSID + Clearance +7 SSD & SSID Roof Thimble Insulated Width SSD SSID 4 to SSDRTIH SSIDRTIH Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

23 SSD & SSID Venting Accessories SSD +2 SSID +4 A B SSD & SSID Suspension Band SSD SSID 4 to 24 SSDSBH SSIDSBH SSD +2 SSID +4 C Figure 46 Figure 47 SSD & SSID Cradle Support SSD SSID 4 to 24 SSDCSH SSIDCSH A SSD + 2 SSID + 4 SSD +2 SSID +4 SSD Wall Support HD A B C 4 1-1/2 to 6-1/ SSD4WSHDP 5 1-1/2 to 6-1/ SSD5WSHDP 6 1-1/2 to 6-1/ SSD6WSHDP 7 1-1/2 to 6-1/ SSD7WSHDP 8 1-1/2 to 6-1/ SSD8WSHDP 9 1-1/2 to 6-1/ SSD9WSHDP /2 to 6-1/ SSD10WSHDP /2 to 6-1/ SSD12WSHDP /2 to 6-1/ SSD14WSHDP /2 to 6-1/ SSD16WSHDP /2 to 6-1/ SSD18WSHDP /2 to 6-1/ SSD20WSHDP /2 to 6-1/ SSD22WSHDP /2 to 6-1/ SSD24WSHDP Figure 49 SSD & SSID Wall Support A SSD SSID 4 to 24 1 to 3 SSDWSP SSIDWSP Figure 48 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 23

24 SSD & SSID Venting Accessories A SSD +2 SSID +4 A B SSD & SSID Anchor Plate A SSD SSID 4 to SSDAPP SSIDAPP Figure 52 SSD +2 SSID +4 C A SSD +2 SSID +4 SSID Wall Support HD A B C 4 1-1/2 to 6-1/ SSID4WSHDP 5 1-1/2 to 6-1/ SSID5WSHDP 6 1-1/2 to 6-1/ SSID6WSHDP 7 1-1/2 to 6-1/ SSID7WSHDP 8 1-1/2 to 6-1/ SSID8WSHDP 9 N/A N/A N/A N/A /2 to 6-1/ SSID10WSHDP /2 to 6-1/ SSID12WSHDP /2 to 6-1/ SSID14WSHDP /2 to 6-1/ SSID16WSHDP /2 to 6-1/ SSID18WSHDP /2 to 6-1/ SSID20WSHDP /2 to 6-1/ SSID22WSHDP 24 N/A N/A N/A N/A SSD & SSID Anchor Plate HD A SSD SSID 4 to SSDAPHDP SSIDAPHDP Figure 53 SSD +2 SSID /2 Figure 50 A SSD & SSID Roof Brace SSD SSID 4 to 24 SSDRBH SSIDRBH A B SSD +2 SSID +4 Figure SSD & SSID Roof Support A B SSD SSID 4 to /2 7-5/8 SSDRSP SSIDRSP Figure 51 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

25 SSD & SSID Venting Accessories 3/4 SSD +2 SSID +4 3 SSD & SSID Guy Wire Band SSD +2 SSID +4 SSD SSID 4 to 24 SSDGWBH SSIDGWBH SSD & SSID Guy Support SSD SSID 4 to 24 SSDGSH SSIDGSH Figure 58 Figure 55 Effective Length 6 SSD +2 SSID +4 SSD & SSID Double Male Adaptor Effective Length SSD SSID 4 to /8 SSDDMAUK SSIDDMAUK Figure 59 1/2 SSD & SSID Centering Band SSD SSID 4 to 24 SSDCBH SSIDCBH Figure 56 Effective Length SSD & SSID Male Flange Adaptor Effective Length SSD SSID 4 to /2 SSDMFAUK SSIDMFAUK Flexible strap by other Figure 60 A SSD +2 SSID +4 1/2 Effective Length SSD & SSID Wall Guide A SSD SSID 4 to 24 1 to 4-1/2 SSDWGH SSIDWGH Figure 57 SSD & SSID Female Flange Adaptor Effective Length SSD SSID 4 to /8 SSDFFAUK SSIDFFAUK Figure 61 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 25

26 SSD & SSID Venting Accessories SSD +2 SSID HEIGHT B 1/2 AERCO BMK Adapter SSD B O.D /4 SSD6AERBMKUK /4 SSD8AERBMKUK /4 SSD14AERBMKUK Figure 62 HEIGHT C B 1/2 AERCO KC Adapter SSD B O.D. C /8 16-1/4 SSD6AERKCUK Figure 63 A SSD Flat Flashing A 4 16 SSD4FH 5 18 SSD5FH 6 26 SSD6FH 7 26 SSD7FH 8 28 SSD8FH 9 30 SSD9FH SSD10FH SSD12FH SSD14FH SSD16FH SSD18FH SSD20FH SSD22FH SSD24FH Figure 64 SSID Flat Flashing A 4 26 SSID4FH 5 26 SSID5FH 6 28 SSID6FH 7 30 SSID7FH 8 30 SSID8FH 9 N/A N/A SSID10FH SSID12FH SSID14FH SSID16FH SSID18FH SSID20FH SSID22FH 24 N/A N/A Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

27 12-1/2 SSD +2 SSID SSD +4 SSID 7 Adjustable from 5 to 30. Roof pitch 1/12 to 7/12. SSD Adjustable Flashing A Figure /2 SSD4FAH /2 SSD5FAH /2 SSD6FAH /8 12-1/2 SSD7FAH /2 12-1/2 SSD8FAH /2 SSD9FAH /2 12-1/2 SSD10FAH /2 SSD12FAH /2 SSD14FAH /2 SSD16FAH /4 12-1/2 SSD18FAH /2 12-1/2 SSD20FAH /2 12-1/2 SSD22FAH /2 12-1/2 SSD24FAH SSID Adjustable Flashing A Figure /2 SSID4FAH /8 12-1/2 SSID5FAH /2 12-1/2 SSID6FAH /2 SSID7FAH /2 12-1/2 SSID8FAH 9 N/A N/A N/A /2 SSID10FAH /2 SSID12FAH /2 SSID14FAH /4 12-1/2 SSID16FAH /2 12-1/2 SSID18FAH /2 12-1/2 SSID20FAH /2 12-1/2 SSID22FAH 24 N/A N/A N/A A Figure 68 SSD & SSID Storm Collar SSD SSID 4 to 24 SSDSCH SSIDSCH SSD & SSID Venting TERMINATIONS SSD SSD Rain Cap with Bird Screen SSD K Factor 4 to 24 SSDRCU SSDRCBUK.50 SSID SSID Rain Cap with Bird Screen SSID K Factor 4 to 24 SSIDRCU SSIDRCBUK.50 Figure 69 SSD & SSID Screened Termination SSD SSID K Factor 4 to 24 SSDSTUK SSIDSTUK.14 Figure 70 5 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 27

28 SSD & SSID 30 Screen Termination SSD SSID K Factor 4 to 24 SSDSTAUK SSIDSTAUK.70 Figure 71 SSD & SSID Mitre Cut SSD SSID K Factor 4 to 24 SSDMCUK SSIDMCUK.14 Figure 74 90% 15 5 SSD & SSID Exit Cone SSD SSID K Factor 4 to 24 SSDECUK SSIDECUK.60 SSD & SSID Closer Termination SSD SSID K Factor 4 to 24 SSDCTUK SSIDCTUK 0 Figure 72 Figure SSD & SSID Termination Tee SSD SSID K Factor 4 to 24 SSDTTUK SSIDTTUK.35 SSD & SSID OEM Termination SSD SSID K Factor 4 to 24 SSDOEMTAUK SSID0EMTAUK 0 Figure 73 Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

29 Center to center Effective length Effective length SSD Vertical Termination Tee SSD Center to center Effective Length 6 SSD6VTTUK /8 8 SSD8VTTUK /8 10 SSD10VTTUK /8 14 SSD14VTTUK /8 Figure 77 SS Adjustable Lengths Effective Length 4 to 24 4 to 5 SSAL9U 4 to 24 4 to 14 SSAL18U 4 to 24 4 to 20 SSAL24U 4 to 24 4 to 32 SSAL36U Figure 79 Effective length SS Venting LENGTHS 1 Effective length SS Test Port Lengths Effective Length 4 to /2 SSTPLU Drain 4 24, 1/4 NPT, 1/2 0.D Figure 80 SS Lengths Effective Length 4 to /2 SSL9U 4 to /2 SSL12U 4 to /2 SSL18U 4 to /2 SSL24U 4 to /2 SSL36U Figure 78 SS Drain Length Effective length Effective Length K Factor 4 to /2 SSDLU 0.25 Drain 4 10, 1/4 NPT, 1/2 0.D Drain 12 24, 1/2 NPT, 5/8 0.D 1 Figure 81 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 29

30 SS Venting ELBOWS 2 30 SS 2-Degree Elbow K Factor 4 1/8 7-1/8 SS4E2U /8 7-1/4 SS5E2U /8 7-1/4 SS6E2U /8 7-1/4 SS7E2U /8 7-1/4 SS8E2U /8 7-3/8 SS9E2U /8 7-3/8 SS10E2U /8 7-3/8 SS12E2U /8 7-1/2 SS14E2U /8 7-5/8 SS16E2U /8 7-5/8 SS18E2U /8 7-3/4 SS20E2U /8 7-3/4 SS22E2U /8 7-7/8 SS24E2U 0.03 Figure 82 SS 30-Degree Elbow K Factor 4 2-1/4 8-1/2 SS4E30U /8 9 SS5E30U /8 9-1/2 SS6E30U /4 10 SS7E30U /8 10-1/2 SS8E30U SS9E30U /8 11-1/2 SS10E30U /8 12-1/2 SS12E30U /8 13-1/2 SS14E30U /8 14-1/2 SS16E30U /8 15-1/2 SS18E30U /2 16-1/2 SS20E30U /4 17-1/2 SS22E30U /2 SS24E30U 0.51 Figure SS 15-Degree Elbow K Factor /4 SS4E15U /8 8-1/8 SS5E15U /8 8-1/2 SS6E15U /8 8-3/4 SS7E15U /4 9 SS8E15U /4 9-1/4 SS9E15U /4 9-1/2 SS10E15U /8 10 SS12E15U /8 10-1/2 SS14E15U /2 11 SS16E15U /2 11-1/2 SS18E15U /8 12-1/8 SS20E15U /8 12-5/8 SS22E15U /4 13-1/8 SS24E15U 0.26 Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. SS 45-Degree Elbow K Factor 4 3-5/8 8-3/4 SS4E45U /2 SS5E45U /4 10-1/2 SS6E45U /2 10-7/8 SS7E45U /8 11-5/8 SS8E45U /8 12-3/8 SS9E45U /8 13 SS10E45U /2 SS12E45U /8 15-7/8 SS14E45U /8 17-1/4 SS16E45U /4 18-3/4 SS18E45U /8 20-1/8 SS20E45U /8 21-1/2 SS22E45U /2 23 SS24E45U 0.08 Figure 85

31 SS Venting ELBOWS SS Venting TEES SS 88-Degree Elbow K Factor 4 7-3/8 7-5/8 SS4E88U /8 8-5/8 SS5E88U /4 9-5/8 SS6E88U /4 10-5/8 SS7E88U /4 11-5/8 SS8E88U /4 12-5/8 SS9E88U /8 13-5/8 SS10E88U /8 15-5/8 SS12E88U /8 SS14E88U /8 SS16E88U /8 21-5/8 SS18E88U /8 23-5/8 SS20E88U /4 25-5/8 SS22E88U /8 27-5/8 SS24E88U 0.20 Figure 86 Available with smaller snout and custom height. Figure 88 SS 43-Degree Tee K Factor /4 6-3/8 11-1/8 SS4T43U /4 7-3/4 12-7/8 SS5T43U /4 8-1/2 13-3/4 SS6T43U /4 9-1/8 14-3/4 SS7T43U /4 10-1/2 16-3/8 SS8T43U /4 11-1/4 17-1/4 SS9T43U /4 12-5/8 19 SS10T43U /4 13-7/8 20-3/4 SS12T43U / /8 SS14T43U /4 17-3/8 25-1/4 SS16T43U /8 27-7/8 SS18T43U /8 30-3/8 SS20T43U /4 32-1/4 SS22T43U /8 34-5/8 SS24T43U SS 90-Degree Elbow K Factor 4 7-1/2 7-1/2 SS4E90U /2 8-1/2 SS5E90U /2 9-1/2 SS6E90U /2 10-1/2 SS7E90U /2 11-1/2 SS8E90U /2 12-1/2 SS9E90U /2 13-1/2 SS10E90U /2 15-1/2 SS12E90U /2 17-1/2 SS14E90U /2 19-1/2 SS16E90U /2 21-1/2 SS18E90U /2 23-1/2 SS20E90U /2 25-1/2 SS22E90U /2 27-1/2 SS24E90U 0.20 Figure 87 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Available with smaller snout and custom height. Figure 89 SS 45-Degree Tee /4 6-5/8 11 SS4T45U /4 8-1/8 12-5/8 SS5T45U /4 8-3/4 13-1/2 SS6T45U /4 9-1/2 14-3/8 SS7T45U /4 10-7/8 16 SS8T45U /4 11-5/8 17 SS9T45U / /8 SS10T45U /4 14-1/2 20-3/8 SS12T45U /4 15-7/8 22-1/4 SS14T45U /4 18-1/8 24-7/8 SS16T45U /4 27-1/2 SS18T45U /4 29-7/8 SS20T45U /8 31-5/8 SS22T45U /2 34 SS24T45U 31

32 SS Venting TEES SS Venting ACCESSORIES 3-1/2 Available with smaller snout and custom height. Figure 90 4 to 8 9 to 24 SS Lateral Secure Tee K Factor /8 9-1/4 8-7/8 SS4BTU /8 10-1/2 10 SS5BTU /8 11-3/4 11-1/8 SS6BTU / /4 SS7BTU /8 14-1/4 13-3/8 SS8BTU /8 12-1/2 12-1/2 SS9BTU /8 13-3/8 13-3/8 SS10BTU /8 15-1/4 15-1/4 SS12BTU / SS14BTU /8 18-7/8 18-7/8 SS16BTU /8 20-3/4 20-3/4 SS18BTU /8 22-1/2 22-1/2 SS20BTU /8 24-3/8 24-3/8 SS22BTU /8 26-1/8 26-1/4 SS24BTU 0.55 Figure 92 Figure 93 SS Tee Cap 4 to /2 SSTCU SS Drain Tee Cap 4 to /2 SSDTCU Drain 4 10, 1/4 NPT, 1/2 0.D Drain 12 24, 3/8 NPT, 5/8 0.D Drain NPT B Drain NPT 3-1/2 Available with smaller snout and custom height. 4 to 8 9 to 24 SS Lateral Secure Tee 88-Degree K Factor /8 9-1/4 9-1/4 SS4BT88U /8 10-1/2 10-1/2 SS5BT88U /8 11-3/4 11-3/4 SS6BT88U / SS7BT88U /8 14-1/4 14-1/8 SS8BT88U /8 12-5/8 13-1/4 SS9BT88U /8 13-1/2 14-1/4 SS10BT88U /8 15-3/8 16-1/8 SS12BT88U /8 17-3/8 18-1/8 SS14BT88U /8 19-1/8 20-1/8 SS16BT88U / SS18BT88U /8 22-7/8 24 SS20BT88U /8 24-3/4 26 SS22BT88U /8 26-5/8 28 SS24BT88U 0.55 SS Tapered Increaser B Available K Factor 4 to /8 SSTIN(B)U to /8 SSTIN(B)U to /8 SSTIN(B)U to /8 SSTIN(B)U to /8 SSTIN(B)U to /8 SSTIN(B)U 0.30 Figure 94 Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

33 SS Venting ACCESSORIES B B Figure 95 B Available SS Eccentric Tapered Increaser K Factor 4 to /4 1/2 SSETIN(B)U to /4 1 SSETIN(B)U to /4 1-1/2 SSETIN(B)U to /4 2 SSETIN(B)U to /4 2-1/2 SSETIN(B)U to /4 3 SSETIN(B)U 0.30 Figure 97 B Available SS Eccentric Tapered Reducer K Factor 5 to /4 1/2 SSETRD(B)U to /4 1 SSETRD(B)U to /4 1-1/2 SSETRD(B)U to /4 2 SSETRD(B)U to /4 2-1/2 SSETRD(B)U to /4 3 SSETRD(B)U to 12 : to 24 : + 11 B Width SS Wall Thimble 4 to 24 9 to 17 SSWTH Figure 98 SS Tapered Reducer B Available K Factor 5 to /8 SSTRD(B)U to /8 SSTRD(B)U to /8 SSTRD(B)U to /8 SSTRD(B)U to /8 SSTRD(B)U to /8 SSTRD(B)U 0.17 Figure 96 Width 4 to 12 : to 24 : + 11 SS Wall Thimble Insulated 4 to 24 9 to 17 SSWTIH Figure 99 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 33

34 SS Venting ACCESSORIES A 10 + Clearance + 3 SS Roof Thimble 4 to SSRTH Figure 100 SS Wall Support 4 to 12 2 to 5 SSWSP 14 to 24 4 to 7 SSWSP Figure Clearance + 3 A SS Roof Thimble Insulated 4 to SSRTIH Figure 101 B C Figure 102 SS Suspension Band 4 to 24 SSSBH SS Cradle Support 4 to 24 SSCSH 1-1/2 SS Wall Support HD A B C 4 2 to SS4WSHDP 5 2 to SS5WSHDP 6 2 to SS6WSHDP 7 2 to SS7WSHDP 8 2 to SS8WSHDP 9 2 to SS9WSHDP 10 2 to SS10WSHDP 12 2 to SS12WSHDP 14 4 to SS14WSHDP 16 4 to SS16WSHDP 18 4 to SS18WSHDP 20 4 to SS20WSHDP 22 4 to SS22WSHDP 24 4 to SS24WSHDP Figure Figure 103 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

35 SS Venting ACCESSORIES B > = 12 < = to 32 3 A SS Roof Support A B 4 to /2 7-5/8 SSRSP 14 to to /2 SSRSP Figure 106 A Figure 109 SS Roof Brace 4 to 24 SSRBH SS Anchor Plate A 4 to SSAPP 14 to SSAPP Figure 107 A Figure 110 SS Guy Wire Band 4 to 24 SSGWBH 6 2-1/2 SS Anchor Plate HD A 4 to SSAPHDP 14 to SSAPHDP Figure 108 Figure 111 SS Centering Band 4 to 24 SSCBH NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 35

36 SS Venting ACCESSORIES A 1/2 Effective length SS Wall Guide A 4 to 24 2 to 5-1/2 SSWGH 14 to 24 4 to 7-1/2 SSWGH Figure 112 SS Male Flange Adaptor Effective Length 4 to /8 SSMFAU Figure 115 3/4 Effective length 3 Figure 113 SS Guy Support 4 to 24 SSGSH 1/2 SS Female Flange Adaptor Effective Length 4 to /4 SSFFAU Figure 116 Effective length SS Double Male Adaptor Effective Length 4 to /8 SSDMAU Figure NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

37 SS Venting ACCESSORIES /2 A Adjustable from 5 to 30 Roof pitch 1/12 to 7/12 A SS Flat Flashing A 4 16 SS4FH 5 16 SS5FH 6 16 SS6FH 7 18 SS7FH 8 26 SS8FH 9 26 SS9FH SS10FH SS12FH SS14FH SS16FH SS18FH SS20FH SS22FH SS24FH Figure 117 SS Adjustable Flashing A /2 SS4FAH /2 SS5FAH /2 SS6FAH /2 SS7FAH /2 SS8FAH /8 12-1/2 SS9FAH /2 12-1/2 SS10FAH /2 12-1/2 SS12FAH /2 SS14FAH /2 SS16FAH /2 SS18FAH /4 12-1/2 SS20FAH /2 12-1/2 SS22FAH /2 12-1/2 SS24FAH Figure SS Storm Collar Effective Length 4 to /4 SSSCH Figure 119 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 37

38 SS Venting TERMINATION /2 SS Rain Cap with Bird Screen K Factor 4 to 24 SSRCU SSRCBU.50 Figure 120 SS Termination Tee K Factor 4 to 24 SSTTU.35 Figure / /2 SS Screened Termination K Factor 4 to 24 SSSTU.14 Figure SS Mitre Cut K Factor 4 to 24 SSMCU.14 Figure SS 30 Screen Termination K Factor 4 to 24 SSSTAU /2 Figure % 15 SS OEM Termination K Factor 4 to 24 SSOEMTAUK 0 Figure 126 SS Exit Cone K Factor 4 to 24 SSECU Figure 123 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

39 Center to center Effective length C SS Vertical Termination Tee Effective Length Center to Center 6 SS6VTTU SS8VTTU SS10VTTU SS14VTTU Figure 127 SS/SSD AERCO APPLIANCE ADAPTERS B 1/2 AERCO KC Adapter SSD B C HEIGHT /8 16 1/4 SSD6AERKCUK Figure 130 C B 1/2 B 1/2 AERCO BMK Adapter SSD B HEIGHT /4 SSD6AERBMKUK /4 SSD8AERBMKUK /4 SSD10AERBMKUK AERCO KC Adapter SS B C HEIGHT /8 17 5/8 SS6AERKCU Figure 131 Figure 128 SSD/AERCO MUFFLER 32 17/32 24 B B 1/2 7 3/32 AERCO BMK Adapter SS B HEIGHT /8 SS6AERBMKU /8 SS8AERBMKU /8 SS14AERBMKU Figure 129 MUFFLER B 6 9 3/4 SSD6MUFFLERAERU /4 SSD8MUFFLERAERU /4 SSD14MUFFLERAERU Figure