ard spray Acrylic enamel spray

Size: px

Start display at page:

Download "ard spray Acrylic enamel spray"

Harold Whitehead
6 years ago
Views:

1 CODE ard f.lli raccanello s.p.a. industria vernici e smalti ard spray Acrylic enamel spray TECHNICAL SHEET 166 GENERAL PROPERTIES ARD SPRAY is an optimum anticorrosive acrylic enamel. It features a remarkable gloss, colour stability & dries quickly. ARD SPRAY contains special corrosion inhibitors which prevent the formation of rust. It is recoatable without scraping & does not contain any dangerous substances such as chrome, lead or chlorine-fluorine derivatives. ARD SPRAY is suitable for decorating and protecting iron substrates, wood, wicker, plastic materials (PVC) etc. both in & outdoors. INSTRUCTIONS Substrate preparation Iron surfaces: degrease with thinner Diluente ARD Remove any flaky metal/rust with a wire brush & emery cloth. Clean thoroughly, apply two coats of ARD SPRAY attending a few minutes between the coats. Treat particularly rusty surfaces, with a coat of ARD SPRAY ANTIRUGGINE. Wooden surfaces: prepare the substrate, sand with fine sandpaper, clean thoroughly and apply ARD SPRAY enamel. Fluorescent and metallic hues are enhanced on white substrates. Chromatic colours are ideal for interior decorations. Application: Shake well (at least 1 min.) before using. At low temperatures warm with lukewarm water. A good result can be obtained by applying a number of very thin coats at intervals of a few minutes. Spray at a distance of about cm. Ensure the ambient is aired sufficiently. Avoid inhaling propellant vapours. Any residues can be conserved by placing the can upside down & pressing the valve for a moment. Store the cans following the usual precautions; keep out of the reach of children and away from heat. Do not dispose until completely empty.

2 TECHNICAL PROPERTIES DUST FREE 10 mins DRYING AT 20 C TOUCH DRY 30 mins THROUGH DRYING 24 hrs YIELD If applied correctly, one can covers a 1.5 m² surface. TENDER SPECIFICATION ITEM ACRYLIC ENAMEL SPRAY Application on pretreated iron or wooden surfaces of two layers of gloss enamel spray based on acrylic resins & lightfast outdoor-resistant pigments with a minimum consumption of - one spray can per approx 1.5 m² -. /m 2. The data herein were correct at the time of Quality Control and refer to standardized environmental conditions. The same are to be considered as a guide. Revision 20012//07 ard f.lli raccanello s.p.a. industria vernici e smalti PADOVA Zona Ind.le Nord 1ª Strada, 13 Tel (5 linee) Fax ardspa@ard-raccanello.it

3 CODE ard f.lli raccanello s.p.a. industria vernici e smalti ard spray zinco Acrylic enamel spray TECHNICAL SHEET 168 GENERAL PROPERTIES ARD SPRAY ZINCO is a highly anti-corrosive cold zincking based on acrylic resins & 95% zinc powder. ARD SPRAY ZINCO is suitable for the anticorrosive protection of metal surfaces in general (coverings, conduits, tanks & rainspouts) & interior/exterior galvanised sheet iron. ARD SPRAY ZINCO does not contain any dangerous substances such as chrome, lead or chlorine-fluorine derivatives. INSTRUCTIONS Substrate preparation: Degrease with thinner Diluente ARD Remove any flaky metal & rust with a wire brush & emery cloth. Clean thoroughly, apply two coats of ARD SPRAY allowing a few minutes between the coats. Ensure the surface is cold before painting. Do not apply near incandescent surfaces or combustive sources. Application: Shake well (at least 1 min.) before using. If the temperature is below 15 C warm with lukewarm water. A good result can be obtained by applying a number of very thin layers at intervals of a few minutes. Spray upright at a distance of about cm. ARD SPRAY ZINCO can be recoated with the ARD SPRAY line of products. Do not overlay using bicomponent products. Ensure premises are aired sufficiently. Avoid inhaling propellant vapours. Any residues can be conserved by placing the can upside down & pressing the valve for a moment. Store the cans following the usual precautions; keep out of the reach of children and away from heat. Do not dispose until completely empty.

4 TECHNICAL PROPERTIES DUST FREE 10 mins DRYING AT 20 C TOUCH DRY 30 mins THROUGH DRYING 24 hrs YIELD If applied correctly, one can covers a 2 m² surface. TENDER SPECIFICATION ITEM ACRYLIC ENAMEL SPRAY Application on pretreated iron or zinc surfaces of two layers of anticorrosive paint spray based on acrylic resins resistant & zinc powder type ARD SPRAY ZINCO with a min. consumption of (1 can) approx 2 m². /m 2. The data herein were correct at the time of Quality Control and refer to standardized environmental conditions. The same are to be considered as a guide. Revision 2007/11 ard f.lli raccanello s.p.a. industria vernici e smalti PADOVA Zona Ind.le Nord 1ª Strada, 13 Tel (5 linee) Fax ardspa@ard-raccanello.it

5 CODE ard f.lli raccanello s.p.a. industria vernici e smalti ard spray nero A.T. Acrylic enamel spray TECHNICAL SHEET 167 GENERAL PROPERTIES ARD SPRAY NERO A.T. is a matt paint based on silicone resins which resist up to 600 C. It is suitable for decorating & protecting interior/exterior iron substrates subject to heat such as wood burning heaters, barbecues, grills, engines & exhaust pipes. ARD SPRAY NERO A.T. does not contain any dangerous substances such as chrome, lead or chlorine-fluorine derivatives. INSTRUCTIONS Substrate preparation: Degrease with thinner Diluente ARD Remove any flaky metal & rust with a wire brush & emery cloth. Clean thoroughly, apply two coats of ARD SPRAY allowing a few minutes between the coats. Ensure the surface is cold before painting. Do not apply near incandescent surfaces or combustive sources. Application: Shake well (at least 1 min.) before using. If the temperature is below 15 C warm with lukewarm water. A good result can be obtained by applying a number of very thin coats at intervals of a few minutes. Spray upright at a distance of about cm. Ensure the surface is perfectly dry before exposing to sunlight (at least 24 hrs are required). Pre-bake the painted substrate at 350 in order to optimize its performance. Do not use on surfaces exposed to temperatures below 150 C. ARD SPRAY NERO A.T. can be recoated with the ARD SPRAY line of products. Do not overlay using bicomponent products. Ensure the ambient is aired sufficiently. Avoid inhaling propellant vapours. Any residues can be conserved by placing the can upside down & pressing the valve for a moment. Store the cans following the usual precautions; keep out of the reach of children and away from heat. Do not dispose until completely empty.

6 TECHNICAL PROPERTIES DUST FREE 10 mins DRYING AT 20 C TOUCH DRY 30 mins THROUGH DRYING 24 hrs YIELD If applied correctly, one can covers a 2 m² surface. TENDER SPECIFICATION ITEM ACRYLIC ENAMEL SPRAY Application on treated iron surfaces of two layers of matt enamel spray based on silicone resins resistant up to 600 C type ARD SPRAY NERO A.T. with a min. consumption of (1 can) approx 2 m². /m 2. The data herein were correct at the time of Quality Control and refer to standardized environmental conditions. The same are to be considered as a guide. Revision 2007/11 ard f.lli raccanello s.p.a. industria vernici e smalti PADOVA Zona Ind.le Nord 1ª Strada, 13 Tel (5 linee) Fax ardspa@ard-raccanello.it

ard spray ard f.lli raccanello s.p.a. industria vernici e smalti TECHNICAL SHEET 166 CODE 2.142

ard spray ard f.lli raccanello s.p.a. industria vernici e smalti TECHNICAL SHEET 166 CODE 2.142 CODE 2.142 ard f.lli raccanello s.p.a. industria vernici e smalti ard spray Acrylic enamel spray TECHNICAL SHEET 166 GENERAL PROPERTIES ARD SPRAY is an optimum anticorrosive acrylic enamel. It features