INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS 2190 Dagenais Blvd.West Laval (Quebec) Canada H7L 5X9 Tel. : Fax : info@burcam.com see us at VERSION Z MODELS SUMP PUMPS Your pump has been carefully packaged at the factory to prevent damage during shipping. However, occasional damage may occur due to rough handling. Carefully inspect your pump for damages that could cause failures. Report any damage to your carrier or your point of purchase. Please read these instructions carefully. Failure to comply to instructions and designed operation of this system, may void the warranty BURCAM Printed in Canada Z

2 SAFETY INSTRUCTIONS: workmanship. Before installation and operation, we recommend the following procedures: A B C D CHECK WITH YOUR LOCAL ELECTRICAL AND PLUMBING CODES TO ENSURE YOU COMPLY WITH THE REGULATIONS. THESE CODES HAVE BEEN DESIGNED WITH YOUR SAFETY IN MIND. BE SURE YOU COMPLY WITH THEM. WE RECOMMEND THAT A SEPARATE CIRCUIT BE LEAD FROM THE HOME ELECTRICAL DISTRIBUTION PANEL PROPERLY PROTECTED WITH A FUSE OR A CIRCUIT BREAKER. THE MOTOR HAVE TO BE SECURELY PLUGGED INTO A PROPER GFCI ELECTRICAL OUTLET. CONSULT A LICENSED ELECTRICIAN FOR ALL WIRING. THE GROUND TERMINAL ON THE THREE PRONG PLUGS SHOULD NEVER BE REMOVED. THEY ARE SUPPLIED AND DESIGNED FOR YOUR PROTECTION. NEVER MAKE ADJUSTMENTS TO ANY ELECTRICAL APPLIANCE OR PRODUCT WITH THE POWER CONNECTED. DO NOT ONLY UNSCREW THE FUSE OR TRIP THE BREAKER, REMOVE THE POWER PLUG FROM THE RECEPTACLE. MONTHLY MANDATORY CHECK-UP : 2. Clear the sump and the surroundings of any paper, leaves or other debris that might clog the input openings. Remove anything that 3. Assure that the pump is secure and vertical for proper operation. 4. Assure that there is adequate clearance from any combustible materials or structure. Stored materials must be kept away from the pump. Shelves or cabinet structures must not be in close proximity over the pump. 5. Test the GFCI outlet by pressing its test switch. This should prove that the outlet is energized and will trip off to protect against a ground fault. Be sure to reset the GFCI by pressing its reset switch. MATERIAL REQUIRED FOR A SUBMERSIBLE SUMP PUMP APPLICATION o Desired length of 1 1/2 or 1 1/4 of ABS/DWV pipe to link up the pump to the drain line. o 1 only 1 1/4 check valve (350353) (Note that this 1 1/4 check valve may also be use with a 1 1/2 pipe). o Sump pit or 1 only sump basin. o 1 1/4-1 1/2 stainless steel clamps (750886). o ABS cement. NOTICE This unit is not designed for applications involving salt water or brine. Use with salt water or brine will void warranty. Tools 2

3 APPLICATION This submersible sump pump is designed for a permanent sump installation. For dewatering around homes and farms. It can be used in light commercial application. CAPACITY: 1/3 HP HEAD USGPH FEATURES Non corrosive material. Stainless steel mechanical rotary seal. Thermal and overload protection. Piggy back grounded cables. 115VAC, 60Hz. 1/3 HP 4A, (9.5A when start) FRICTION LOSS IN PIPE NOT INCLUDED INSTRUCTION STEPS Please note before you proceed with the installation of this product that the manufacturer s IMPORTANT NOTICE guideline has to be respected. Failure to comply may void your warranty. your personal responsibility to protect your home, family and valuables. Failure to comply with the following requirements may also void your warranty: Two (2) pumps have to backup unit. Burcam alarm system model has to be installed to advise you of any malfunctions. model has to be installed to evacuate the water. STEP 1 STEP 2 We recommend that you install your pump in a clean location where there is adequate room for servicing at a later date. Protection from freezing temperatures and good ventilation should be considered as well, to provide the pump an environment for long life. Do not use to pump gas or toxic fuels. This submersible sump pump is designed to pump water only. Friction losses in the discharge pipe must be taken into consideration when the horizontal offset is greater than 50 feet. The discharge pipe should be increased from 1 1/2 to 2. This will reduce friction losses and allow the pump to give maximum performance. of head. Never run the pump dry. Damage to the seal may occur. Fill pump pit or sump basin with water before turning on the power. be constructed from concrete, brick, tile or more recently a sump basin made from plastic must be than 25 deep. When pit is ready, proceed to next step. 3

4 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 SUMP PUMP APPLICATION (SEE DIAGRAM ON PAGE 5) At this step, you have the opportunity to install a 1 1/2 or a 1 1/4 discharge. We recommend MNPT inlet and 1 1/4 or 1 1/2 outlet) over discharge pipe of your pump and secure it with stainless steel clamps or glued nipple for ABS/DWV pipe. This check valve will allow easy access to pump, should service be required. Install and position your submersible sump pump in the centre of your sump pit or basin and Install your discharge pipe from check valve to the point of discharge or drain. For installation over 50 feet of horizontal position discharge pipe, use a 2 pipe to reduce friction loss. The vertical switch provided with your pump is supplied with a serial electrical male plug. Fix electrical grounded outlet. We recommend that a licensed electrician be employed to do wiring. Permanently ground the motor in accordance to the electrical codes for your area. Do not use an extension cord to connect your pump to the power source. From your distribution panel to the receptacle, we recommend a wire gauge not smaller than 14 gauge. Use tape or tie wrap to Fill the sump pit or basin with water to test the operation of your submersible sump pump. The motor should start when the water level reaches approximetely 3 over your pump. Allow trouble shooting guide in this manual. Review your installation with typical diagram. Check all connections for leaks. MAINTENANCE Unplug the switch and pump motor power cord. Remove the pump from pit or basin. Remove freely after cleaning. If tar or paint has been received in the pit or basin, use kerosene to Do not use strong paint solvents. Remove the screws that hold the strainer or the base to the bottom of the pump body. Pry the base off the pump body carefully. Clean the impeller and volute passage way from any debris wich may have become in contact with these parts. Again, If tar or paint has entered pump, clean with kerosene. Do not use strong paint solvents. Be sure impeller turns freely after cleaning. Check and clean away any debris wich may be clogging the suction inlet, pump discharge, check valve and discharge line. screws and return sump pump to sump pit or basin and reconnect to piping. 4

5 SUMP PUMP APPLICATION STEP 3 Prepare your choice of discharge pipe size and check valve STEP 2 Sump pit 18 diameter X 25 depth STEP 7 Fill the basin and test the operation STEP 6 motor power cables STEP 5 Install discharge pipe STEP 8 Review and check connections for leaks STEP 4 Install your pump in centre of pit REPAIR PARTS REF. PART DESCRIPTION REF. PART DESCRIPTION Pump volute Impeller (1/3HP) Impeller (1/2HP) Impeller (1/4HP) Pump base Discharge reducer Stator (1/3HP) Stator (1/2HP) Stator (1/4HP) Upper bearing Rotor (1/3HP) Rotor (1/2HP) Oil seal Mechanical seal Pump gasket Capacitor (1/3HP) Capacitor (1/2HP) Capacitor (1/4HP) Upper casing Screws (2) Power cable Vertical switch ; (300601, , ) Switch bracket Mechanical switch ; Mechanical switch ; (300500) (not shown) 5

6 TROUBLE SHOOTING GUIDE CHECKLIST NEVER MAKE ADJUSTMENTS TO ANY ELECTRICAL APPLIANCE OR PRODUCT WITH THE POWER CONNECTED. DON T JUST UNSCREW THE FUSE OR TRIP THE BREAKER, REMOVE THE POWER FROM THE RECEPTACLE. TROUBLE PROBABLE CAUSE ACTION Motor does not run. Switch is off position Blown fuse Tripped breaker Plug disconnected Corroded plug Low water level Thermal overcharge Defective motor Turn switch to on position Reset Clean prongs Add water and verify Cool the motor /repair Check movement Pump does not deliver to full capacity. Jammed impeller Plugged check valve Blocked suction/inlet Discharge leak Blocked line/pipe Worn impeller Defective motor Clean Clean/replace Check for debris in pit and clean Repair Check for debris or ice Repair/replace Pump does not shut off Defective switch Float obstruction Blocked suction/inlet Check for debris in pit and clean TO THE END CONSUMER If you have any problems with the product, before advising the store, where you ve purchased the pump, please contact us at , and ask for our sales department, and they will be pleased to help you with any questions you might have, concerning your installation. 6