Ellure Tile Look Walls
|
|
- Denis Stephens
- 6 years ago
- Views:
Transcription
1 Ellure Tile Look Walls Ellure Tile Look Walls - FITTING INSTRUCTIONS Included in this package: Other equipment that may be required 1 x Corner Flashing Drill 2 x Side finishing trim Adhesive application gun 1 x Ellure Tile Look Walls fitting Hole Saw instructions (this booklet) Jigsaw with 40 TPI tooth blade 1 x Full length plastic infill (2400) Skillsaw with 100 tooth blade 1 x Short length plastic infill Diamond continuous wheel in grinder Included in this package: 2 x Corner Flashing Drill Other equipment that may be required 2 x Side finishing trim Adhesive application gun 1 x Ellure Tile Look Walls fitting Hole Saw instructions (this booklet) Jigsaw with 40 TPI tooth blade 1 x Full length plastic infill (2400) Skillsaw with 100 tooth blade 1 x Short length plastic infill Diamond continuous wheel in grinder Atlantis recommends this installation is undertaken by an experienced tradesperson. PLEASE ENSURE WALLS ARE PLUMB & LEVEL PRIOR TO INSTALLATION DRY FIT WALLS TO ENSURE CORRECT FIT
2 2 WALL SHOWERS ENSURE WALL BOARD IS POROUS (Note: sealed or painted wall won t allow proper adhesion) 1. Unpack and check-over the components. 2. Using the supplied white silicone, apply two continuous 8mm beads of silicone vertically to both walls, where the Ellure corner flashing will adhere to the wall lining. Firmly press the Ellure corner flashing to the wall lining, in the orientation shown, to suit your shower base (see SQUARE or RECTANGLE SHOWER BASE below). SQUARE SHOWER BASE Corner Flashing position RECTANGLE SHOWER BASE Corner Flashing position LEFT HAND RECTANGLE SHOWER BASE RIGHT HAND RECTANGLE SHOWER BASE 3. Dry fit the Ellure Wall Panels into the corner flashing. Ensure the panels are positioned on the correct sides as per diagrams above. If you have purchased your Ellure Tile Look Walls with a feature panel, also dry fit the feature panel and panel joiners at this time. Refer to the back page of these instructions for further information about fitting an Ellure Feature Panel.
3 4. Carefully measure and mark the tapware penetrations (Figure 1). Drill a small pilot hole through the Ellure wall panel from the front surface. Cut the large holes from the back of the wall panel. USE EXTREME CARE WHEN CUTTING THE LARGE HOLES 5. Trim the Ellure Wall Panels to the desired height (DO NOT RUSH THIS PROCESS) (Figure 1), if necessary. Please see the back page of these instructions for further information about altering the sheet size. 6. Remove the protective film off the back of the Ellure Wall Panels and apply 5mm beads of Showerbond in vertical lines at approx. 100mm centres, to the back of your Ellure Wall Panels. 7. Apply a continuous 8mm bead of white silicone around the shower base upstand, below the counter sunk screws (if applicable) and to both sides of the corner flashing (Figure 2 and 3). FIGURE 1 FIGURE 2 8. Carefully place the Ellure wall panels into position and press firmly into place. Smooth air out from behind the Wall Panels with a padded block or similar, working from the internal corner out. Prop panels in place if necessary. 100% contact should be achieved between the Wall Panels and shower base upstand. FIGURE 3 9. Wipe any excess silicone off. 10. Fit Ellure Finishing Trim and Wall Channels as per Figure 4 and 5 Figure 4 Figure 5
4 3 WALL SHOWERS ENSURE WALL BOARD IS POROUS (Note: sealed or painted wall won t allow proper adhesion) 1. Unpack and check-over the components. 2. Using the supplied white silicone, apply two continuous 8mm beads of silicone vertically to both sides of LH corner only, where the Ellure LEFT HAND corner flashing will adhere to the wall lining. Firmly press the Ellure LEFT HAND corner flashing to the wall lining, in the orientation shown (Figure 6). FIGURE 6 3. Dry fit the Ellure Wall Panels, following the order of installation shown in figure 7 and figure 8, to ensure the panels are positioned on the correct sides. If you have purchased your Ellure Tile Look Walls with a feature panel, also dry fit the feature panel and panel joiners at this time. Refer to the back page of these instructions for further information about fitting an Ellure Feature Panel. 4. Carefully measure and mark the tapware penetrations (figure 1). FIGURE 7 Drill a small pilot hole through the Ellure wall panel from the front surface. Cut the large holes from the back of the wall panel. USE EXTREME CARE WHEN CUTTING THE LARGE HOLES. 5. Trim the Ellure Wall Panel sheets to the desired height (Figure 1), if necessary. Please see the back page of these instructions for further information about altering the sheet size. 5A. Apply two continuous 8mm beads of silicone vertically to both walls, where the Ellure RIGHT HAND corner flashing will adhere to the wall lining (Figure 7). 6. Remove the protective film off the back of the Ellure Wall Panels and apply 5mm beads of Showerbond in vertical lines at approx. FIGURE 8 100mm centres, to the back of your Ellure Wall Panels. 7. Apply an 8mm continuous bead of white silicone around the shower base upstand, below the counter sunk screws (if applicable) (Figure 2) 8. Following the order of panel installation shown in Figure 7 and Figure 8, carefully place the Ellure wall panels into position and press firmly into place. Smooth air out from behind the Wall Panels with a padded block or similar, working from the internal corner out. Prop the panels in place if necessary. 100% contact should be achieved between the Wall Panels and shower base upstand. 9. Wipe any excess silicone off. 10. Fit Ellure Finishing Trim and Wall Channels as per Figure 9 and 10 FIGURE 9 FIGURE 10
5 Ellure Tile Looks Walls with Fixed Panel or Sliding Door For showers where there is no glazing channel on one side of the shower entry the Ellure Feature Panel is finished with the finishing trim and the plastic infill. Figure 13 Figure 13
6
7 Fitting Ellure Tile Looks Walls with Feature Panel For showers where the feature wall is positioned on a side 1400mm or less, the Ellure Feature Panel will be factory assembled. Please continue with your installation as per the steps in the main instructions. For showers where the feature panel is on a side larger than 1400mm, the feature wall is supplied in two parts. 1. Dry fit the Ellure wall panels, following the order of installation shown in Figure 11 then Figure 8, to ensure panels are on the correct sides. FIGURE 11 FIGURE As per step 4, carefully mark and cut the tapware penetrations (Figure 1) 3. As per step 5, trim the Ellure wall panels to the desired height (Figure 1), if necessary. 4. As per step 5A (for 3-wall showers), apply two continuous 5mm beads of Showerbond vertically down both walls, and firmly press the Ellure RIGHT HAND corner flashing to the wall lining. 5. As per step 6, remove the protective film and apply silicone vertically to the back of the Ellure wall panels. 6. As per step 7, apply a continuous bead of silicone around the shower base upstand. 7. As per step 8, follow the order of panel installation shown in Figure 11, carefully place the Ellure Wall Panels into position and press firmly into place. Referring to Figure 12, join the Ellure feature and adjacent panel by applying a continuous 5mm bead of silicone vertically to the aluminium joining strip. Continue panel installation as per Figure 8 Smooth air out from behind the Wall Panels with a padded block or similar, working from the internal corner out. Prop the panels in place if necessary. 100% contact should be achieved between the Wall Panels and shower base upstand. 8. Wipe any excess silicone off. 9. Fit Ellure Finishing Trim and Wall Channels, as per Figure 9 and 10. Cutting Ellure Tile Looks Walls NOTE: This acrylic is harder than common wall liners; therefore it is also more prone to damage. NOTE: Handle the panels carefully when drilling or cutting, and ensure the sheet is well supported around and/or under where the cutting is being performed. NOTE: It is advisable to leave the original protection film on the Ellure Wall Panel until all cutting is done, to protect the face of the panel. You may also wish to tape over the face of the panel, along where you re cutting, to protect the panel. Hand tools that can be used to cut the Ellure Wall Panels: Jigsaw with 40 TPI tooth blade, Skillsaw with 100 tooth blade, diamond continuous wheel in grinder, hand held buzzer. A belt sander may also be used.
rockspan installation guide horizontally laid panel
rockspan installation guide horizontally laid panel A 1. Check all support steelwork has been installed within standard dimensional tolerances. Check that the width of the steel bearing face is consistent
More informationBASE MKII SHOWER SCREEN & BASE
page of 8 900 x 900 x 000 (mm) 000 x 000 x 000 (mm) Dimensions are nominal measurements only. To see the complete BASE range go to www.reece.com.au/bathrooms SPECIFICATIONS Recommended use Material Frame
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking (See specific caulking recommendations) caulking gun shims tape measure 1/8 drill bit Phillips screw driver
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws caulking gun shims tape measure 1/8 drill bit Phillips screw driver cardboard china marker (or grease pencil) furring strips
More informationVistelle Installation Guide. Edition 2
Vistelle Installation Guide Edition 2 Introduction Vistelle is the superior high gloss acrylic panel especially suited for shower walls, bathroom partitions and kitchen splashbacks in residential or commercial
More informationInstallation Guide. Thank you for your order PLEASE READ these entire instructions BEFORE you START
Installation Guide Acrylic Wall Installation Tiled Wall Installation Thank you for your order PLEASE READ these entire instructions BEFORE you START PH: 09 913 3110 FAX:09 913 3113 5 Smales Road East Tamaki,
More informationFreeStyle Linear Drain with Full Mortar Bed Adapter Kit
FreeStyle Linear Drain with Full Mortar Bed Adapter Kit U.S. Patent No. 8,474,068 Patents Pending: Canada & EP Publication No. 2354339 Discard Linear Drain installation instructions and refer to these
More informationInstallation Instructions
Please read all instructions before installing products. STORAGE: BioPrism wall cladding must be stored flat and fully supported with no sagging or bowing. The pallets that BioPrism wall cladding are shipped
More informationBRISTOL SHOWER SYSTEMS
SHOWER SYSTEMS page of 000 x 000 x 000mm Shower Wall Shower Base SPECIFICATIONS Recommended Use Material Domestic, hotel and commercial 6mm toughened glass shower screen with fully framed chrome door and
More informationadjustable fusion shower pan surface mounted on subfloor installation guide
a a) Wall b) Tile c) Adjustable Shower Pan d) Liquid Membrane e) Crack Isolation Tape f) Cement Board g) Subfloor h) Joists b d c f h g e adjustable fusion shower pan surface mounted on subfloor www.trendingaccessibility.com
More informationSTEP UP SHOWER BASE INSTALLATION GUIDE FOR TIMBER AND CONCRETE FLOORS
GUIDE FOR TIMBER AND CONCRETE FLOORS EDITION: APRIL 2016 IMPORTANT: This guide is for the installation of a Step Up shower base on a timber or concrete floor. If you require a walk in (flush with floor)
More informationfusion shower pan on wood joists installation guide
a a) Wall b) Tile c) Shower Pan d) Liquid waterproofing e) Crack Isolation Tape f) Cement Board g) Subfloor h) Joists b c d f h g e fusion shower pan on wood joists installation guide www.trendingaccessibility.com
More informationGlasboard Liners. installation details. Installation Guide for Glasbord Fibreglass Reinforced Plastic (FRP) panels
Glasboard Liners installation details Installation Guide for Glasbord Fibreglass Reinforced Plastic (FRP) panels PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION These guidelines are provided
More informationBRISTOL SHOWER SYSTEMS
page of 6 900 x 900 x 000 (mm) 000 x 000 x 000 (mm) 00 x 900 x 000 (mm) Dimensions are nominal measurements only. To see the complete BRISTOL range go to www.reece.com.au/bathrooms SPECIFICATIONS Recommended
More information6032 SH 3P Residential Shower Installation Instructions Gelcoat & Solid Surface Bathware
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking caulking gun acrylic latex caulk shims tape measure 1/8 drill bit Phillips screw driver cardboard china
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE: BioPrism wall cladding must be stored flat and fully supported with no sagging or bowing. The pallets that BioPrism wall cladding are shipped
More informationEuro Frameless Sliding Shower Screen Installation Instructions
Euro Frameless Sliding Shower Screen Installation Instructions Frameless Reversible Chrome Fittings 8mm Clear Safety Glass Can be installed on shower base or tiled floor Front Only Available sizes: To
More informationYARRABEE 360 GEOLOGY
Thank you for choosing our fine hand crafted GEOLOGY slate panels. For the best results, we believe that a contractor or professional wall covering installer with the correct tools should hang this material.
More informationInstall & Maintenance Instructions
Arterra Installation Please read these instructions thoroughly prior to beginning the Arterra installation. Inspect all materials for damage or missing parts. If you discover damaged or missing materials,
More informationadjustable fusion shower pan on wood joists installation guide
a a) Wall b) Tile c) Shower Pan d) Liquid Membrane e) Crack Isolation Tape f) Cement Board g) Subfloor h) Joists b d c f h g e adjustable fusion shower pan on wood joists installation guide www.trendingaccessibility.com
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS MAGNET SEAL PACK,TO FORM 8MM HINGED CORNER ENTRY ENCLOSURE THESE INSTRUCTION REPLACE THE SET SUPPLIED WITH THE SHOWER DOORS. V04/09/2014 BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
More informationMODULAR ACOUSTIC FENCING INSTALLATION GUIDE
MODULAR ACOUSTIC FENCING WWW.QUICKBUILTSYSTEMS.COM.AU INSTALLATION GUIDE INTRODUCTION THE QUICKBUILT FENCE SYSTEM IS A SMARTLY DESIGNED MODULAR SYSTEM EASY AND FAST TO INSTALL AND COST EFFECTIVE. // THE
More informationPittsburgh Corning Glass Block Shower System Mortar Installation Standard Fit Shower Instructions
1. Shower Base and Wall Preparation 1.1 After installation of the shower base, line base with paper or cardboard to protect during installation of the glass blocks. Measure 2 ½ inches out from the inside
More informationStraight Panel Bath Screen Instruction Manual
Straight Panel Bath Screen Instruction Manual Consumer Guarantee - Please make sure the purchaser/end user completes and returns the Guarantee card which is enclosed with this product. Failure to validate
More informationINSTALLATION INSTRUCTIONS This leaflet must be read thoroughly before commencing installation. Scan for more information
Scan for more information INSTALLATION INSTRUCTIONS This leaflet must be read thoroughly before commencing installation Showerwall is the ultimate versatile easy to fit waterproof panelling system, with
More informationrainspan installation guide horizontally laid panel
rainspan installation guide horizontally laid panel standard details A C 1. Check all support steelwork has been installed within standard dimensional tolerances. Check that the width of the steel bearing
More informationSQUARE SUN TUNNEL INSTALLATION INSTRUCTION
SQUARE SUN TUNNEL INSTALLATION INSTRUCTION Please leave these installation instructions with the owner of the Sun Tunnel. This will enable them to carry out the straightforward maintenance mentioned below.
More informationOutward Folding Bathscreen Instruction Manual
Outward Folding Bathscreen Instruction Manual OBV3 Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according
More informationaquapanel InstallatIon GuIde
Installation Guide AQUAPANEL BEFORE YOU START It s a good idea to stand the AQUAPANEL sheets in the area for 2 days prior to cutting and installing, to allow the sheets to breathe and reach moisture equilibrium.
More informationKADO LUX shower system
page 1 of 18 KADO Centre Outlet 461 461 1200 1200 599 599 1000mm x 1000mm 114 114 845 845 Rear Outlet 1145 845 845 1145 300 300 835 835 1400 835 1400 835 1200mm x 900mm 300 Dimensions are nominal measurements
More informationWALK-IN SHOWER BASE INSTALLATION GUIDE FOR CONCRETE FLOORS
WALK-IN SHOWER BASE INSTALLATION GUIDE FOR CONCRETE FLOORS EDITION: APRIL 2016 IMPORTANT: If you require a Walk In shower base for timber floors, please go to our support page at www.hydroblok.com.au IMPORTANT:
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE & HANDLING: Check for damage that may have occurred during transit. Keep receptor flat on pallet, as it was shipped, until ready to install.
More informationSpaVault TM Installation Guide for Bullfrog Spas (7-10 x 7-10 x 38 )
SpaVault TM Installation Guide for Bullfrog Spas (7-10 x 7-10 x 38 ) WARNING - When unpacking SpaVault, DO NOT discard styrofoam pieces, these are not packaging materials. Step 1 Excavation Important:
More informationPrior to commencing installation please carefully read this installation booklet in full paying particular attention to the do s and dont s.
Bifrost Wood Plastic Composite Wall Panels Adhesive Mounted Wall Panels Bifrost WPC wall panel is the ultimate versatile easy to fit waterproof and fireproof panelling system. The basic board is made of
More informationeuropanel installation guide horizontally laid panel
europanel installation guide horizontally laid panel A 1. Check all support steelwork has been installed within standard dimensional tolerances. Check that the width of the steel bearing face is consistent
More informationKWiK N EZ Rigid Track Silicone System
Page 1 of 6 PITTSBURGH CORNING KWiK N EZ Rigid Track Silicone System ASSEMBLY INSTRUCTIONS Introduction The KWiK N EZ Rigid Track Silicone System is the easiest way to install Pittsburgh Corning Thinline
More informationPITTSBURGH CORNING ASSEMBLY INSTRUCTIONS. KWiK N EZ Rigid Track Silicone System for Thinline Series Glass Block
Page 1 of 6 PITTSBURGH CORNING KWiK N EZ Rigid Track Silicone System for Thinline Series Glass Block ASSEMBLY INSTRUCTIONS Introduction The KWiK N EZ Rigid Track Silicone System is the easiest way to install
More informationFrameless Hinged Door - Alcove. These instructions must be left with the user. Installation Guide W2-B
Frameless Hinged Door - Alcove These instructions must be left with the user Installation Guide 1 1290647-W2-B 1290647-W2-B 2 Introduction Thank you for purchasing a quality product. To enjoy the full
More informationEuro Corner Entry Shower Screen Installation Instructions
Euro Corner Entry Shower Screen Installation Instructions Corner Entry Space Saving Design Dual Sliding Doors, magnetic seals Silver Frame 6mm Clear Safety Glass Can be installed on shower base or tiled
More informationGenesis Panel Systems LLC Dura-Max Brick Panel Siding Installation Instructions
Genesis Panel Systems LLC Dura-Max Brick Panel Siding Installation Instructions Thank you for purchasing the Genesis Dura-Max Brick Panel system for your project. The system allows you to have the look
More informationPittsburgh Corning ProVantage Glass Block Installation System Assembly Instructions
Pittsburgh Corning ProVantage Glass Block Installation System Assembly Instructions Introduction: The ProVantage Glass Block Installation System is the easiest way to install Pittsburgh Corning Premiere
More informationMIRA FLIGHT WALL Installation and User Guide. These instructions are to be left with the user W2-E
MIRA FLIGHT WALL Installation and User Guide These instructions are to be left with the user 1 INTRODUCTION Thank you for purchasing a quality Mira product. To enjoy the full potential of your new product,
More informationInstallation Guide. PAROC panel solutions
Installation Guide PAROC panel solutions Panel System 4.00 INT January 2008 THESE INSTRUCTIONS ARE FOR NORMAL APPLICATIONS Work safety Preparation Wear protective gloves and clothing when handling the
More informationThe professionals choice. Installation instructions Torridon. shower tray
The professionals choice. Installation instructions Torridon shower tray 1 2Torridon Patent pending Before installation please check: All component parts of your assembly, including fixings, are present
More informationKingspan Day-Lite Klick
Insulated Panel Envelope Systems Roof Wall Façades Lighting Rooftop PV Coldstore Structural Products Cleanrooms UK & Ireland Kingspan Day-Lite Klick Installation Guide Page 2 Accessories Overview Designation
More informationWALL TILE CHARACTERISTICS
WALL TILE CHARACTERISTICS Casabella Tile's ceramic wall material is made with white, atomized clay. All clays and minerals used within the body of the tile and surface glaze are natural and inert after
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS INFINITI 8mm SLIDER/SLIDER WITH SIDE PANEL THIS PRODUCT IS UNIVERSAL. LEFT HAND OPENING ILLUSTRATED. CHANGE THE HAND BY TURNING THE DOOR/SIDE PANEL UPSIDE DOWN. V03.09.2015 BEFORE
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE & HANDLING: Check for damage that may have occurred during transit. Keep receptor flat on pallet, as it was shipped, until ready to install.
More informationASSEMBLY INSTRUCTIONS INFINITI 8mm 1-DOOR QUADRANT
ASSEMBLY INSTRUCTIONS INFINITI 8mm 1-DOOR QUADRANT V05.09.2015 BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION 1) General Information Please inspect this product upon delivery. Any missing parts or
More informationALCOVE - SLIDING Alcove Shower System Installation Guide for Liner Style & Accent Liner Style Showers
TM ALCOVE - SLIDING Alcove Shower System Installation Guide for Liner Style & Accent Liner Style Showers Congratulations on the purchase of your new shower system. This guide will give you the instructions
More informationTo ensure your Multipanel Tile is properly bonded, ensure all surfaces to which adhesive will be applied are clean, dry and flat.
Jig saw or Hand saw Measuring Tape Ruler Pencil High-grab adhesive Silicone Sealant Masking Tape Drill & Screwdriver Pre-installation check-list Inspect panels for any flaws, defects or damage* Check colour
More informationINSTALLATION GUIDE IMPORTANT
INSTALLATION GUIDE SLIDING SIDE PANEL DOOR VIVID 10 IMPORTANT Thank you for choosing Merlyn. Please familiarise yourself with the fitting instructions before commencing fitting. 1. Check that you have
More informationWall Protection Installation Guidelines
SureProtect Pure Hygienic Wall Cladding Data Sheet: Page 1 of 8 August 2016 1. Substrate suitability and recommended preparation All material must be installed in environmentally controlled conditions.
More informationSlimLine Single Threshold Base & Q-Wall-5.1 BASE & BACKWALL INSTALLATION INSTRUCTIONS
SlimLine Single Threshold Base & Q-Wall-5.1 BASE & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For
More informationImportant Information
Hinged Door Instruction Manual CL Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to our guidelines.
More informationHOME SYSTEMS CONSTRUCTION PROCEDURE
HOME SYSTEMS WWW.QUICKBUILTHOMES.COM.AU CONSTRUCTION PROCEDURE INDEX - PARTS LIST PARTS LIST QBRC75(C) QBRM75C) QBSIPS75 QBRFSZ75C QBRFBC75C QBRF3030G QBRGSQC QBRFRC75C QBRFZEC QBRF4040C QBSACC75 QBFR7330WC
More informationSlimLine Neo-Angle Base & Q-Wall-2
SlimLine Neo-Angle Base & Q-Wall-2 BASE & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest
More informationSINGLE ALCOVE - S-80S
TM SINGLE ALCOVE - S-80S Single Threshold Shower System Installation Guide for Liner Style & Accent Liner Style Showers Congratulations on the purchase of your new shower system. This guide will give you
More informationFREEWILL BARRIER FREE ACRYLIC BATH AND SHOWER MODULES
FREEWILL BARRIER FREE ACRYLIC BATH AND SHOWER MODULES BEFORE YOU BEGIN PREPARATION The basin area requires no additional support when the subfloor is plumb and level with respect to the stud frame. Shim
More informationWALL TILE CHARACTERISTICS. DUNES GLASS TILE
DUNES GLASS TILE Product is clear float glass with a glazed rear face. Due to the clear nature of the material some shadows may be visible at tile edge when viewed at an angle. This is not a manufacturing
More informationWARMUP TILED SHOWER SOLUTION
WARMUP TILED SHOWER SOLUTION INSTALLATION INSTRUCTIONS NOTE: this instruction detail is specific to the requirements of the Tiled Shower solution and must be read in conjunction with the ARDEX WPM750 membrane
More informationPTY LTD. Paskaseal SRB. Screed Replacement Base
PTY LTD Paskaseal SRB Screed Replacement Base brochure main 3 - bluegreen.indd 1 About Us Visit us at paskaltileandstone.com.au We encourage you to come in and speak to our highly trained experts. Paskal
More informationDetailing guide for senior living facilities
Detailing guide for senior living facilities Creating an integrated system with Altro flooring and wall cladding is an ideal solution for areas in which hygiene and water resistance are a top concern.
More informationTILE RANGE. Pre-installation check-list
Pre-installation check-list Jig saw or Hand saw Measuring Tape Ruler Pencil High-grab adhesive Silicone Sealant Masking Tape Drill & Screwdriver Inspect panels for any flaws, defects or damage* Check colour
More informationINSTALLATION INSTRUCTIONS FOR PLASCORE L2550 LINER WALL
INSTALLATION INSTRUCTIONS FOR PLASCORE L2550 LINER WALL The following information is provided by Plascore, Inc., as a general guideline for the installation of the L2550 Liner Wall System. This information
More information8mm FRAMELESS CONCEALED HINGE DOOR WITH SIDE PANEL
8mm FRAMELESS CONCEALED HINGE DOOR WITH SIDE PANEL Refer To Sheet 9 For Relevant Product Codes Decide which hand is required. Right hand opening illustrated. Change the hand by turning the side panel upside
More informationPremium wall cladding. Complete system. Installation guide. Preparation Profiles Sheet preparation and installation After care
Premium wall cladding Complete system Installation guide 1969 Preparation Profiles Sheet preparation and installation After care Cladright wall cladding installation guide This installation guide complies
More informationGRP Flat Roofing Edge Trims
GRP Flat Roofing Edge Trims Compatible with GRP, rigid and flexible polyester, polyurethane, acrylic and alkyd systems. Trim Brochure and Technical Specification Guide General Information The Easy To Use
More informationInstallation Manual SELT6032-WH SERT6032-WH SELC6032-WH SERC6032-WH
Installation Manual SELT6032-WH SERT6032-WH SELC6032-WH SERC6032-WH 60" x 32" Seated Base Left 60" x 32" Seated Base Right 60" x 32" Seated B/W Combo Left 60" x 32" Seated B/W Combo Right 20 22 18 Tall
More informationExterior System installation instructions
Exterior System installation instructions 11/20/14 WPS ES-400 & 500 INSTALLATION INSTRUCTION. The WPS ES-400 & 500 systems Façade panels are designed for use as an external wall cladding in conjunction
More informationShower Pan Extension Installation Guide
Shower Pan Extension Installation Guide Before Installing your HYDRO-BLOK Shower System Perform a final floor and wall measurement check to ensure all walls are square and make any adjustments required
More information1850 x 40/50mm Raised Shower Tray Kit
Installation Instructions 850 x 40/50mm Raised Shower Tray Kit Parts Supplied Description Qty Shower Tray Shower Tray Extension Parts Required (Fitting Kit) Materials Required Description Qty Description
More informationSpacia Curved Shower Screen Installation Instructions
Spacia Curved Shower Screen Installation Instructions Enclosure comprises of screen, wall & base Chrome D Handles Available size 1000mm x 1000mm Base, Screen height: 2000mm Base entry height 70mm, overall
More informationPrime Shower Enclosure & Base Kit
Prime Shower Enclosure & Base Kit SHOWER ENCLOSURE AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior
More informationDecking Installation Guide
Decking Installation Guide Starting your project Following delivery of your composite decking boards, we recommend you allow them 24 hours to adjust to local temperature conditions before starting work.
More informationAqua Swing Tub Door & EX/RT Panel
Aqua Swing Tub Door & EX/RT Panel TUB DOOR AND PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest
More informationInstallation Guide Single-Hung, Picture & Shapes Non-Impact & Impact Resistant Florida Flange Windows
Non-Impact & Impact Resistant Florida Flange Windows americancraftsmanwindows.com Project Requirements: Read guide before starting installation. Read all warnings and cautions during installation. Check
More informationPrime Shower Enclosure & Base
Prime Shower Enclosure & Base SHOWER ENCLOSURE & BASE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest
More informationARSTYL WALL PANELS STONE
ARSTYL WALL PANELS STONE Installation instructions Architecture & Design 2-3 Installation instructions MATERIALS REQUIRED Sandpaper grit 150 or finer Brush/sponge Spirit level Ruler Pencil Nail clamps
More informationPolarex PVC Hygienic Wall Cladding Installation Guide
Polarex PVC Hygienic Wall Cladding Installation Guide Version 2.1 15.08.2018 Product Overview Polar Hygienic Finishes offers a semi-rigid, smooth, and durable PVC sheet. The material is thermoplastic and
More informationInfinity - Century Combination Installation Instructions Gelcoat & Solid Surface Bathware
Tools and materials you might need for proper installation: Level Caulking gun Drill Scissors Jig saw or router Wood file or 180 grid sand paper 100% silicone caulking Clamps Galvanized screws (8) 1 bolts
More information8mm FRAMELESS CONCEALED HINGE DOOR
8mm FRAMELESS CONCEALED HINGE DOOR Refer To Sheet For Relevant Product Codes Decide which hand is required. Right hand opening illustrated. Change the hand by turning the fixed panel upside down. The moving
More informationIllustration shown here features a right hand, shelf wall unit.
WHIRLPOOL R BATH 2 Wall Shower System INSTALLATION INSTRUCTIONS Create the shower environment you want within the space you have with Jacuzzi Whirlpool Bath's innovative modular shower system. This custom
More informationa3 CERAMICSTEEL FLOW TECHNICAL GUIDE
a3 CERAMICSTEEL FLOW TECHNICAL GUIDE PolyVision a3 CeramicSteel Flow provides an ideal blend of consistent performance, a variety of aesthetic choices and long-term durability. Whether used as a full height
More informationNiagara / DLG-85 Shower Cabin Installation and User s guide
Niagara / DLG-85 Shower Cabin Installation and User s guide I. Mounting Preparation 1. After opening the case, read this introduction carefully, check all the packed parts, examine the shower cabinet for
More informationSINGLE BOWL VESSEL VANITY
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the floor, walls,
More informationBRANZ Appraisal Certificate # 461 (2010) Internal wet areas.
SPECIFICATION FOR PROTECTO WRAP AFM-WM FOR INTERNAL WET AREAS BRANZ Appraisal Certificate # 461 (2010) Internal wet areas AFM/WM INTERNAL 0104 Page 1 AFM-WM INTERNAL SPECIFICATION PRODUCT DESCRIPTION Anti
More informationWALL-HUNG VANITY WITH VESSEL SINK
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the floor, walls,
More informationCornerview Shower Enclosure & Base
Cornerview Shower Enclosure & Base SHOWER ENCLOSURE AND BASE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For
More informationRevision Date: April 01, Premier Vinyl Enclosure
Premier Vinyl Enclosure www.urbanindustries.com 53 Urban Industries, Inc. 2008 Tools The following tools are recommended for the installation of the Premier Vinyl Enclosure and roof. 1 2 Level 1 4 Level
More informationABC32 - ABC36 - ABC42
Acrylic Shower Base Model ABC32 - ABC36 - ABC42 INSTALLATION MANUAL ABC32 - ABC36 - ABC42 Table of Contents IMPORTANT... 2 CARE FOR YOUR ACRYLIC SHOWER BASE... 2 SPECIFICATION.... 3 TOOLS AND MATERIALS
More informationMounting Screw. Channel Filler. Light Angle Adjustable Screw. LED Board Vertical stud and blocking Locking Nose. Driver.
The Knife Edge Cove is a modular lighting system consisting of two parts: 1- An aluminum fixture housing extrusion 2- Drop-in lighting modules The fixture will provide a continuous knife edge architectural
More informationResysta Wall Cladding Installation Guidelines
Resysta Wall Cladding Installation Guidelines NOTE: Proper planning of the wall cladding layout is essential for ease of installation of wall cladding boards and wall cladding components. Thoroughly read
More informationMirroFlex Tub and Shower Walls Kit Installation Instructions
MirroFlex Tub and Shower Walls Kit Installation Instructions MirroFlex Tub and Shower Walls must be acclimatized for 24 hours before installation! PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION: The
More informationIntroduction. Before you begin. Structure installation
Installation Manual Introduction Thank you for choosing a Valley product! This installation manual provides you with general information on the proper installation of our bath products. IMPORTANT NOTE:
More informationWALL-HUNG VANITY WITH SEMI-RECESSED SINK
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the floor, walls,
More informationChannel Drain Shower Base. Aqua Line pro. Installation Instructions
Channel Drain Shower Base. Aqua Line pro Installation Instructions 02 JACKOBOARD Aqua Line pro System components a JACKOBOARD Aqua Line pro b JACKOBOARD Aqua Line pro - Horizontal Drain (Art. No. 4510370)
More informationDecorative Panel Instalation
www.eucatex.com.br /EucatexOficial @Eucatex_Oficial @Eucatex_Oficial Decorative Panel Instalation Decorative Panel Instalation Congratulations, you are accept the linha melamina de painéis Eucafibra BP
More information84 Lapping & Jointing 86 Service Pipe Penetrations 87 Sealing to Cavity Wall Constructions 88 Protecting Membranes System Components.
84 Lapping & Jointing 86 Service Pipe Penetrations 87 Sealing to Cavity Wall Constructions 88 Protecting Membranes 90 System Components installation/ SYSTEM COMPONENTS INSTALLATION ADVICE LAPPING and JOINTING
More informationPANELITE. Bonded Series Fabrication Guide
PANELITE Bonded Series Fabrication Guide www.panelite.us (c) Panelite 2012 PANELITE Bonded Series Handling and Storage General The plastic film protects panel surfaces. Keep the protective film in place
More information