Detailing guide for senior living facilities

Transcription

1 Detailing guide for senior living facilities Creating an integrated system with Altro flooring and wall cladding is an ideal solution for areas in which hygiene and water resistance are a top concern. Within the senior living market these areas may include showers, nurse-assisted bathing areas, commercial kitchens, medical rooms and indoor swimming facilities. Proper installation techniques are critical in these areas, which is why Altro products must be installed as per the instructions in this guide and the Altro installation guide. Failure to comply may void the limited product warranty. Overview Senior living is institutional by nature, and health codes tend to reinforce this. That s why designers are looking at performance benefits and high quality commercial installation techniques when choosing floor and wall finishes. In this segment, the potential for injury and illness is very high, which is why proper detailing and transitions are sensitive and require a quality installation Facilities Guidelines Institute Guidelines for Design and Construction of Residential Health, Care and Support Facilities The new standard for residential facilities provides minimum recommendations for new construction and renovation of nursing homes, hospice facilities, assisted living facilities, independent living settings, adult day care facilities, wellness centers and outpatient rehabilitation centers. Key points relating to installation techniques: To reduce Hospital-Acquired Infections, surfaces must be non-absorbent, non-porous and smooth Flooring surfaces shall provide smooth transitions between different flooring materials Flooring surfaces must be cleanable and wear resistant Slip resistant flooring required in bathing areas and rooms, ramps and entries Slip resistant flooring required in kitchens with all joints sealed Areas subject to wet cleaning methods should have homogeneous, heat-welded flooring with the material flash-coved. TECH>INSTALL>DETAILING GUIDE FOR SENIOR LIVING

2 Altro flooring to Altro wall cladding Overlap joint method (preferred) The preferred method of installing Altro WALL SUBSTRATE WHITEROCK flooring with Altro Whiterock is the overlap DOUBLE-SIDED TAPE joint method. This installation is made by using a cove former to run the safety flooring 6-8 up the wall. Altro Whiterock 2 ALTRO WHITEROCK SANITARY SEALANT is then overlapped 2 over the safety 2 OVERLAP 2 flooring. The overlap of the product ensures a complete seal from floor to wall transition and does not need to rely on heat welding to achieve that seal. 4-6 COVE FORMER SAFETY FLOOR SUBFLOOR Altrofix adhesive Heat welded joint method WHITEROCK Occasionally a heat welded transition from Double sided tape Grooved & Heat Welded Joint WSBU 200 PVCu INFILL WALL SUBSTRATE floor to wall is necessary. In instances like these, use the heat welded joint method. This installation is done by installing Altro Whiterock wall cladding first, with the bottom of the panel being 4-6 above the floor. Altro flooring is then installed using a cove former to run the material up the wall with a small amount of overage extending above the wall cladding. Using the wall cladding as a cutting guide, the SAFETY FLOOR extra flooring is trimmed away and then heat welded with the wall cladding. This COVE FORMER installation method is more labor intensive and requires precision with the heat welding gun. OR FLO SUB

3 Cove methods Altro Whiterock Altro Whiterock vinyl panels vinyl panels or similar or similar Most Altro sound Most Whiterock sound and dry and substrates dry vinyl substrates panels or similar Silicone Silicone sealant sealant (by wall (by contractor) wall contractor) Most sound and dry substrates Altro C-4 Altro cap C-4 strip cap strip Silicone sealant (by wall contractor) Altro C-7 Altro cap C-7 strip cap strip Sit on cove Sit on cove AltroMastic AltroMastic Sit on cove AltroMastic Altro Altro flooring Altro C-4 flooring cap strip.080" to.080".14" to.14" (2mm to (2mm 3.5mm) to 3.5mm) Min. Altro 4" (100mm) flooring.080" Self to cove.14" Cove (2mm former Cove to 3.5mm) former Min. 4" (100mm) Self cove Cove former Altro C-7 cap strip Altro flooring Altro flooring.080" to.080".14" to.14" (2mm to (2mm 3.5mm) to 3.5mm) Altro flooring.080" to.14" Cove former Cove (2mm former to 3.5mm) Cove former Sit on Sit cove on cove detail detail C-4 detail C-4 detail C-7 detail C-7 detail Altro floor Alt.080" to.08.1 (2mm to (2mm 3.5 Sit on cove detail C-4 detail C-7 detail Approved Approv adhesive adhes Glazed Glazed wall tile tile wall or or tile or vinyl wall vinyl cladding wall cladding Masonry Masonry nail fixing nail fixing hole drilled hole in in drilled vinyl in first vinyl first Existing Existing Wall Finish Wall Finish AltroMastic AltroMastic Quarry Quarry tile skirting tile skirting or or similar similar existing existing skirting skirting Ceramic Ceramic tile tile bullnose bullnose overlap overlap WSBU200 WSBU ins or Altro C-8 Altro cap C-8 strip cap strip Altro C-11 Altro cap C-11 strip cap strip Sanitary Sanitary sealant sealant Altro flooring Altro flooring.080" to to.080".14" to.14" (2mm to to (2mm 3.5mm) to 3.5mm) Most sound Most sound and and dry substrates dry substrates Altro flooring Altro flooring.080" to.080".14" to.14" (2mm to (2mm 3.5mm) to 3.5mm) Altro flooring Altro flooring.080" to.080".14" to.14" (2mm to (2mm 3.5mm) to 3.5mm) Cove former Cove former Quarry Quarry tile floor tile floor Cove former Cove former C-8 detail C-8 detail C-11 C-11 detail detail Ceramic Ceramic tile bullnose tile bullnose overlap overlap detail detail

4 Capstrip and cove former details Altro flooring installed with a C7 and C8 cap strips are pictured below. These strips are the most commonly used. C7 cap strips are used to finish your Altro flooring installation to dry wall (and no other wall finish is being installed). C8 cap strips are used when Altro flooring is being installed with a ceramic tile wall finish. C4 cap strips are available for installing Altro Whiterock in an alternative method. We still recommend the overlap method on the majority of installations. Door frame C7 Cove former reduced to architrave Door frame C8 Cove former reduced to architrave

5 using Altro contact tape of appropriate width for transition. Using Altrofix 30 two part polyurethane adhesive, install Altro sheet vinyl on smooth, dry, suitable substrate and weld to wet room transition. Shower transition trim Altro Aquarius to shower transition trim to sheet vinyl Heat weld Sheet vinyl Altro Aquarius in shower Altro sheet vinyl to Altro or other sheet vinyl transition Altro Altrofix sheet vinyl polyurethane installed using appropriate adhesive Altro adhesive on smooth, dry, suitable substrate. Transition to be heat welded with Altro weldrod. If seaming to other manutacturer s sheet flooring use that manufacturer s weldrod. Sound substrate Flooring transitions D - Wetroom transition (Gradus WT series, or equivalent) Sheet vinyl Sheet vinyl For additional technical help please call or info@altrofloors.com Heat weld Altro LVT/plank to Altro sheet vinyl transition Altro LVT/plank and sheet vinyl installed using appropriate Altro adhesive on smooth, dry, suitable substrate. PVC seam sealer used to bond flooring together. A heat weld can also be used at this transition. Sound substrate Carpet tile with PVC backing explore altro.com PVC cement B Altro sheet vinyl Vinyl shim A Sound substrate Sheet vinyl to other sheet vinyl transition Carpet tile to sheet vinyl A - Subfloor leveler system (Johnsonite LS-40, or equivalent) B - PVC cement (Oatey heavy duty - clear, or equivalent) For additional technical help please call or info@altrofloors.com Seam sealer C explore altro.com Sheet vinyl LVT/pank Sound substrate Sheet vinyl to LVT plank C - PVC seam sealer (Lonseal Lonsealer, or equivalent) C - PVC seam sealer (Lonseal Lonsealer, or equivalent)

6 Drains New round drains and cleanouts Clamping drains are the best choice for proper installations, and the only choice for areas where water penetration concerns are a priority. These drains are readily available from plumbing supply distributors. They may be installed at time of concrete placement or retrofitted. They are screw on and height adjustable. They come in a variety of drainage pipe diameters and cover sizes. We prefer the larger cover sizes. The following are acceptable drains: Zurn Z 415, Mifab F1100-FC, Wade 1100-FC, Josam AD, Watts FD 100-FC, Smith 2051 MIFAB F1100-FC Floor Drain with Surface Membrane Clamp 7 (175) or 9 (230) floor covering vandal resistant stainless steel screws fc nickel bronze strainer surface membrane clamp strainer adjustment body height Sample of an approved clamping drain Note: In most cases, it will be necessary to weigh down the drain area to allow the Altrofix 30 two-part adhesive to setup. Caution: Failure to weigh down the drain area during this process may cause a bubble or a pucker in the Altro floor covering, to which there is no remedy.

7 Modifying an existing drain Remove the drain cover plate. With a quality cementitious patching compound, finish the subfloor flush with the drain perimeter. Note: If drain body is higher than the concrete surface, it must be either ground-off or chipped out and lowered. If the drain body is lower than the concrete surface, you must slightly grind the concrete surface to allow for a slight slope-to-drain profile. Using a small hand held electric grinder, remove the square shoulder on the inside edge of the drain body to create a 45-degree slope into the drain. Similarly, remove the square shoulder from the perimeter of the back side of the drain cover plate creating a 45-degree slope to match the drain body. Replace the cover plate screws for the purpose of land marking the screw holes and preventing the adhesive from filling the holes during the gluing process. Diagram A Square shoulders Square shoulders Diagram B Square shoulder Square shoulder Diagram C Altro flooring covering Gluing and cutting process Apply adhesive (Altrofix 30 two-part polyurethane or approved polyurethane adhesive) on the floor, around, and onto the sloped perimeter of the drain. Place the Altro floor covering over the drain, and fit cut only to the inside diameter of the drain plate screws. Note: Cutting to the outside of the screws will cause the material to be short of the drain plate once it is re-installed. Cut small windows in the Altro floor covering at the drain plate screws only. After all final fitting is completed, warm material with a hot air blower and secure the drain plate cover in place. This process pinches the Altro floor covering between the drain body and the drain plate cover.

8 Full installation details available on altro.com USA / CAN support@altrofl oors.com For technical support please call and speak with our Technical Services department.