ADDENDUM NO.03 ADDITION AND RENOVATIONS TO DEMOSTHENEAN HALL FOR BUCKNELL UNIVERSITY CFB PROJECT NO March 28, 2017

Transcription

1 ADDENDUM NO. 03 ADDITION AND RENOVATIONS TO DEMOSTHENEAN HALL FOR BUCKNELL UNIVERSITY CFB PROJECT NO March 28, 2017 TO ALL BIDDERS: This Addendum No.03 dated March 28, 2017, consists of, 2 drawing reissues, 1 product cut sheet, and 12 Contractors RFI s with CFB s responses and includes revisions to the Drawings and Specification Sections listed below. It shall be considered part of the respective Contract Documents, dated March 13, Issued for Construction. SPECIFICATIONS: SECTION NO. DESCRIPTION OF CHANGE Foamed-In-Place Insulation Page of4, 2.4, Miscellaneous Materials, add B. Thermal Barrier Fire Protective Coating: Flame Control No A compatible with insulation manufacturer s rating for fire-protective coating on underside of all exposed spray foam insulation in Attic area compliant with IBC thermal barrier. See attached product sheet 16-09_Flame Control 60-60A Add Rough Carpentry Page of B delete reference to sections Sheathing and Shop-Fabricated Wood Trusses. For plywood underlayment see Section Summary Page of add Bucknell University will install temporary Fire Alarm System hooked up to the Dana Engineering Building to remain in operation at all times during project. Page of8 1.6.C.4 add Bucknell University will install a sectionalizing switch at the Bertrand Library electric sectionalizing cabinet. Page of F delete Existing Sprinkler System section Plumbing Scope Remove #8 from the Description of Work item, regarding the pool equipment. DRAWINGS: ARCHITECTURAL SHEET NO. DESCRIPTION OF CHANGE A100 Door 006 detail callout on A100 corrected to 8/A800. A614, A615 Automatic Hand Dryers (9A) are owner supplied and contractor installed. ADDENDUM NO.03 Bucknell University Page 1 of 2 Celli-Flynn Brennan Architects and Planners (16-09) 03/28/2017

2 Mounting Heights A950 CWT-1 and CTB-1 to be used in Rooms 005, 007, 011. CWT-2, CTB-2 and CTB-3 to be used in Rooms 210,212,310,312. Delete CTB-4 from finish legend. ELECTRICAL SHEET NO. E001 Electrical Coversheet E202 First Floor Plan - Lighting Add to the coversheet symbols DESCRIPTION OF CHANGE to be a fire alarm Individual Addressable Module. Revise Numbered Note #2 to read, Under alternate number 3 delete the four type Y light fixtures, wiring, and conduit associated with the North patio and brick piers. STRUCTURAL SHEET NO. DESCRIPTION OF CHANGE S103 Add detail section 8/302. S302 Add detail section 8/302. PLUMBING SHEET NO. FP201 First Floor Plan Fire Protection DESCRIPTION OF CHANGE Sprinkler indicated in STAIR 2 is to be located below the first accessible landing above the bottom of the shaft. ADDENDUM NO.03 Bucknell University Page 2 of 2 Celli-Flynn Brennan Architects and Planners (16-09) 03/28/2017

3

4

5 FLAME CONTROL NO A 15 Minute Thermal Barrier on Spray Polyurethane Foam A Low VOC, Water Based Product Product Description: Flame Control No A has met the criteria for use as a 15-minute thermal barrier on Spray Polyurethane Foam (SPF). No A is a low VOC, water-based intumescent coating that dries to a flat finish. No A was subjected to flammability testing per NFPA 286 and successfully met the criteria listed in the 2006, 2009, 2012, and 2015 International Building Code (IBC) and International Residential Code (IRC) Flame Control No A is suitable for use in inhabited spaces where spray foam insulation must be separated from the interior of the building per IBC Section special approval. Characteristics: Finish Flat Shelf Life 1 Year Color White, Black, Tints VOC Less Than 40 g/l Type of Cure Coalescence Flash Point None Application Temperature 50 F (10 C) *** See Application Reducer/Cleaner Water Temperature Section Solids By Weight 65% Packaging 5 & 55 gal. containers Tinting Universal Paint Colorant: 2 Fluid ounces per gallon maximum Application Brush, Roller, Spray Drying 77 F (25 C) & 50% R.H. To touch: 1-2 Hours To Recoat: 2 4 hours Thermal Barrier Spread Rate 20 mils WFT: 80 Sq Ft/Gallon 18 mils WFT: 89 Sq Ft/Gallon Surface Preparation: All surfaces to be painted must be clean and cured. The foam must be firm, dry and free of dust, dirt, oil, wax, grease, and mildew. The quality of any paint job is only as good as the surface preparation that precedes the paint application. Flame Control 60-60A has excellent bonding characteristics and will adhere to most sound, clean, foam surfaces. Make sure the surface of the foam is free of holes, exposed cells, and that the surface is stable and not crumbling or deteriorated. If any defects are found, repair them prior to proceeding. Mildew should be removed by scrubbing with a 25% solution of household bleach water. Tri-sodium phosphate (TSP) or common laundry powder such as Tide may be added to solution to assist removal. Temperature: 60-60A is water based coating which will freeze at temperatures below 32 F. Care should be taken to protect the material from freezing. Should 60-60A freeze, warm the material to at least 60 F and thoroughly mix prior to application. It is not recommended to store material at temperatures below 50 F. Do not apply 60-60A when ambient air and substrate temperatures fall below 50 F. Store at 50 F to 80 F. Important: Humidity 65% and higher must use fans to move air for curing. High humidity may require longer cure times. Please consult with your local code officials to verify that your application complies with the appropriate code requirements. Material Preparation:

6 FLAME CONTROL NO A 15 Minute Thermal Barrier on Spray Polyurethane Foam A Low VOC, Water Based Product 60-60A must be thoroughly mixed before application. Failure to do so will compromise the protective capabilities of Flame Control 60-60A. We recommend mechanical stirring with a high speed drill and a paddle appropriate for the size container. Contents should be stirred from the bottom up, making sure to scrape the bottom and sides with a paint stick as you go. Contents should be stirred to a creamy consistency with no lumps A is a water based product and slight thinning will not hurt the product. It should be noted that thinning increases the likelihood of not applying the proper film thickness, resulting in decreased fire protection capabilities. It is the sole responsibility of the applicator to ensure the proper film thickness has been applied A should never be mixed with other materials, however tinting using universal paint tint is acceptable A can be tinted up to a maximum of 2 fluid ounces per gallon (10 ounces per 5-gallon pail). Application Equipment: 60-60A can be applied by brush, roller or airless sprayer. Brushing: Use top quality polyester/nylon blend brushes Rolling: 3/8 polyester blend nap roller covers generally work well when applying 60-60A by roller. Spraying: Airless Spray Minimum: PSI: 3000 PSI or higher or equivalent Filter: 30 mesh, removal of filter is recommend from gun and machine Hose: 1/4 diameter airless spray line for the first 50 from pump and ¼ x 6 whip Tip: GPM:.95 For best results use, Hose: 3/8 diameter airless spray line for the first 50 from pump and ¼ x 6 whip and no filters gun and machine. Pump: (Titan) 740 Impact or equivalent PSI: 3300 / 227 GPM:.80 Tip: or equivalent. Filter: 30 mesh, removal of filter is recommend from gun and machine Hose: 1/4 diameter airless spray line for the first 50 from pump and ¼ x 6 whip Pump: (Graco) Ultra Max II 795 Hi-Boy or equivalent PSI: 3300 / 227 GPM:.95 Tip: or equivalent. Filter: 30 mesh, removal of filter is recommend from gun and machine Hose: 1/4 diameter airless spray line for the first 50 from pump and ¼ x 6 whip Pump: (SprayTex) GPX 130 or equivalent PSI: 3300 / 227 GPM: 1.30 Tip: or equivalent. Filter: 30 mesh, removal of filter is recommend from gun and machine Hose: 1/4 diameter airless spray line for the first 50 from pump and ¼ x 6 whip For Best results: For all Jobs big or small: Pump: (Graco) Mark 4 or 5 or equivalent PSI: 3300 / 227 GPM: 1.35 Tip: or equivalent. Filter: 30 mesh, removal of filter is recommend from gun and machine Hose: 3/8 diameter airless spray line for the first 50 from pump and ¼ x 6 whip For Smaller Jobs Residential and Small Warehouses:

7 FLAME CONTROL NO A 15 Minute Thermal Barrier on Spray Polyurethane Foam A Low VOC, Water Based Product Application Equipment Continued: For 55 gallon Drums: Pump: (Graco) GH 300 or equivalent PSI: 3300/ 227 GPM: 3.0 / 11.4 Tip: or equivalent. Filter: 30 mesh, removal of filter is recommended from gun and machine. Hose: 3/8 diameter airless spray line for the first 50 from pump and ¼ x 6 whip Pump: (Graco) GH 833 or equivalent PSI: 4000/ 276 GPM: 3.0 / 11.4 Tip: or equivalent. Filter: 30 mesh, removal of filter is recommend from gun and machine Hose: 3/8 diameter airless spray line for the first 50 from pump and ¼ x 6 whip Workmanship: General: Apply 60-60A according to manufacturer s written instructions. Use applicators and techniques best suited to the type of foam being applied. Do not paint over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions detrimental to forming a durable paint film. Paint surfaces behind movable equipment and furniture the same as similar exposed surfaces. Coverage: Check test report for square feet per gallon and mil thickness. Example: At a rate of approximately 20 wet 80 square feet per gallon, application dry film thickness (DFT) will be approximately 10.3 mils. The final (DFT) will vary and depends on the substrate of the specific assembles. Checklist Before You Start: Temperature - Is temperature within limits (50 to 90 F)? Humidity - Is the relative humidity less than 65%? Consistency - Are the contents thoroughly mixed? Surface - Are all substrates clean, dry and sound? Measurement - Wet film gauge on site? Need help - Call Correct spray tips 517 thru 537 Airless sprayer with minimum.08 GPM Electrical power and at minimum 12 gauge extension cord Power drill & mixer of appropriate size Drop cloths or poly sheeting Disposable gloves, mask, protective eyewear Clean metal flashing or equivalent for spray (or clean metal flashing) Portable fans to speed drying Disposable paint brushes Work lights for tight areas Scaffolding (as required) Clean-up rags 2 five gallon pails for clean-up Dish detergent for clean-up 1-2 oz. Curing time: 7-11 Days Revised 6/16

8 RF 011 PROJECT: Bucknell University Demosthenean Hall PROJECT NO. CFB CFB RFI NO. 011 Celli Flynn Brennan Architects Phone: INQUIRER S RFI NO. 1 INQUIRER: _Burton Stover E MAIL: _burt@dynamicsprayfoamcom ISSUE DATE: 3/23/17 CO. NAME: _Dynamic Spray Foam & Coatings PHONE: _ RFI DESCRIPTION: _Closed Cell spray foam Application RFI: 1. What is the requested depth (or anticapated R value) for the closed cell spray foam in the vented attic assembly? 2. Will the attic area meet appendix X Criteria, or will a 15 min thermal/ignition barrier be required as a coating over the SPF? REFERENCES / ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: A105, A106.11, A107.3, A107.8, A301, A302, A361.1 OTHER: 1. The anticipated R value is R Refer to specifications modification section on coversheet of this Addendum No.3. RESPONDER: Jeff Wright DATE: 03/27/17

9 RFI 012 PROJECT: Bucknell University Demosthenean Hall PROJECT NO. CFB CFB RFI NO. 012 Celli Flynn Brennan Architects Phone: INQUIRER S RFI NO. 4 INQUIRER: _Toby Eshenauer E MAIL: _teshenauer@wohlsen.com ISSUE DATE: 3/24/17 CO. NAME: _Wohlsen Construction PHONE: _ RFI DESCRIPTION: RFI: 1. What are the 4 circles in the walls on each side of the fireplace? 2. Please confirm the gas company will be tying into the main and supplying and installing the gas piping to the meter. 3. Detail 9/ A800 is indicated at door 006 on A100. Detail 9/ A800 only shows the jamb though. Please provide the detail and elevation of this opening and sidelite. 4. In spec section Rough Carpentry, part 1.2 B, there is a reference to spec sections Sheathing and Shop Fabricated Wood Trusses but neither of the spec sections were provided. Please provide these. 5. Since there is no lead report for the areas that are existing to remain, should an allowance be created for abatement items that are to remain? 6. Sprinkler specification notes that the sprinkler contractor needs to be a subcontractor to the plumbing contracted. Please confirm this is not required.

10 RFI 012 REFERENCES / ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: 1. Refer to note 4 on H Supplying and installing the gas pipe and connecting to the existing gas line that runs to the meter at the SW corner of DANA is part of The Work. Contractor shall coordinate with UGI Gas Service and Bucknell Facilities. 3. Refer to door 006 on A800. Door 006 detail callout on A100 corrected to 8/A800. Refer to coversheet Addendum No. 3 drawing modification A Refer to coversheet Addendum No. 3 Section No. Refer to of D for hazardous material requirements. 6. This is not a requirement. RESPONDER: Jeffrey Wright DATE: 3/27/17

11 RFI 013 Project: Bucknell University Project No. CFB CFB RFI No. 013 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. 1 ISSUE DATE: 3/27/17 INQUIRER: Stephen Thaler CO. NAME : Lundy Construction E MAIL: swt@lundyconstruction.com Phone : Ext 103 RFI DESCRIPTION: Project Estimate RFI : Our Bonding Company has asked for the Design Professional s Estimate of Project Cost. Please provide that estimated cost or range in an Addendum. REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: The estimate is not the responsibility of the architect and therefore any budgetary amount suggested can no way impact contractor s insurances and bonds. Insurance and bond amounts are the responsibility of the contractors. That said, the budget for this project is between 5 and 6 million dollars. RESPONDER: Jeffrey Wright DATE: 3/27/17

12 RFI 014 Project: Bucknell University Project No. CFB CFB RFI No. 014 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. ISSUE DATE: INQUIRER: Steve Scholl CO. NAME : Silvertip Inc E MAIL: Estimating@silvertip inc.com Phone : RFI DESCRIPTION: Bucknell Demosthenean Hall RFI : On Drawing H101 Note #13 states to clean the existing duct. Does this note apply to all of the existing duct with in the building? REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: The only duct the remains in the building and will require cleaning is located in the basement, Digital Humanities Lab 012 basement and a small section Seminar 006 connecting to new corridor trunk line. All other ductwork is to be removed. RESPONDER: CJL DATE: 03/27/17

13 RFI 015 Project: Bucknell University Project No. CFB CFB RFI No. 015 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. 1 ISSUE DATE: INQUIRER: Dave Montgomery CO. NAME : Schrader Architectural Products E MAIL: monty@schraderproducts.com Phone : RFI DESCRIPTION: RFI : There are no specifications for the Auto hand Dryers. Are these to be provided by owner? If pricing is needed, the manufacturer, possibly a model # and the voltage information is required. REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: A614, A615 OTHER: Hand dryers are owner supplied and contractor installed. See cover sheet this Addendum No. 3. RESPONDER: JSW DATE: 3/28/17

14 RFI 016 Project: Bucknell University Project No. CFB CFB RFI No. 016 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. SMI # 1 ISSUE DATE: 3/27/17 INQUIRER: Bob Spencer CO. NAME : Spencer Mec., Inc E MAIL: bspencersmi@comcast.net Phone : RFI DESCRIPTION: RFI : Addendum #2 HVAC scope page 1 existing fan coil units as to replace any parts to make the unit fully operational this is unknown information how can we put a price to it? REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: The number of replacement parts for fan coil units are unknown. It is the contractor s responsibility to have sufficient amount to cover the cost of replacing parts. RESPONDER: Jeff Wright DATE: 3/27/17

15 RFI 017 Project: Bucknell University Project No. CFB CFB RFI No. 017 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. SMI # 1 ISSUE DATE: 3/27/17 INQUIRER: Bob Spencer CO. NAME : Spencer Mec., Inc E MAIL: bspencersmi@comcast.net Phone : RFI DESCRIPTION: RFI : Addendum #2 HVAC scope page 1 existing fan coil units as to replace any parts to make the unit fully operational this is unknown information how can we put a price to it? REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: Refer to RFI 016 response. RESPONDER: Jeff Wright DATE: 3/27/17

16 RFI 018 PROJECT: Bucknell University Demosthenean Hall PROJECT NO. CFB CFB RFI NO. 018 Celli Flynn Brennan Architects Phone: INQUIRER S RFI NO. 5 INQUIRER: _Toby Eshenauer E MAIL: _teshenauer@wohlsen.com ISSUE DATE: 3/27/17 CO. NAME: _Wohlsen Construction PHONE: _ RFI DESCRIPTION: RFI: 1. Spec section notes that the existing sprinkler system needs to remain in operation throughout the construction period and be in operation at the end of each day. Please confirm this is not required for this project as the existing branch lines and heads are being removed and the entire system is being changed from glycol to wet system. 2. Both the A101 Contract and the A201 General Conditions reference Supplemental Conditions of the Contract. Please provide a copy of the Supplemental Conditions of the Contract. 3. The AIA document A notes that the Contractor shall be responsible for paying deductibles associated with the Builder s Risk insurance that is provided by the Owner. What is the deductible amount? 4. The AIA document A101 notes that the Contractor is expected to comply with CAD Standards for Bucknell University. Please provide a copy of those standards. 5. Are dual shades solar fabric and blackout fabric required at all exterior windows, or only at the motorized shade in room # 102? Is single shade fabric to be used on all other rooms, and if so, what is the specified fabric? 6. Spec section B indicates performance requirements are Bucknell University general signage standards. Please provide signage standards. 7. Follow up to HVAC scope added in addendum #2. More information is needed to accurately quantify a scope for this work. It is recommended that either an allowance be provided for these existing fan coils or provide a selection of a replacement fan coil. In the scope listed in addendum #2 it notes to Place any parts to make the unit fully operational. Contractors are not aware what parts are needed during the bidding phase. Do the motor needs replaced? What about cosmetic issues in the existing units? 8. Alternate #3 description indicates that the patio lighting is in the base bid and the alternate would be to delete these lights. Note 2 on E202 would indicate that Alternate #3 would include the patio lights. Please confirm.

17 RFI Please confirm what the following symbol represents on the electrical drawings. 10. The ceramic wall tile and ceramic tile base have not been designated on the Room Finish Schedule. Please indicate where CWT 1, CWT 2, CTB 1, CTB 2, CTB 3 and CTB 4 should be provided. REFERENCES / ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: 1. The existing sprinkler does not need to remain operational. Also, Bucknell University to provide a temporary fire alarm system for this project that will be tied into Dana Engineering building. Contractor to maintain operation of fire alarm throughout duration of project. Ref to cover sheet Section of this addendum. 2. There are no Supplemental Conditions to the contract for this project. 3. The deductible amount is $50, After award of contract Bucknell Cad Standards will be sent. 5. Dual Shades only in #102. Refer to section of6,2.4,B for Light filtering fabric. 6. Refer to Interior signage page G The number of replacement parts for fan coil units are unknown. It is the contractor s responsibility to have sufficient amount to cover the cost of replacing parts. 8. Note 2 on E202 will be revised to match Alternate #3 Description. 9. The symbol is a fire alarm Individual Addressable Module. 10. CWT 1 and CTB 1 to be used in Rooms 005, 007, 011. CWT 2, CTB 2 and CTB 3 to be used in Rooms 210,212,310,312. CTB 4 is not used. Refer to cover sheet this Addendum No. 3. RESPONDER: JSW DATE: 3/28/17

18 RFI 019 Project: Bucknell University Project No. CFB CFB RFI No. 019 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. ISSUE DATE: INQUIRER: Steve Scholl CO. NAME : Silvertip Inc E MAIL: Estimating@silvertip inc.com Phone : RFI DESCRIPTION: Bucknell Demosthenean Hall RFI : Drawing H201 the duct mains from HPAHU 1 and HPAHU 2 are tagged as 9X9. Is the dimension 9X9 consistant for the entire main? REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: Yes, 9 x 9 is to be the consistent size for the main duct as per the manufacturer. RESPONDER: CJL DATE: 3/28/17

19 RFI 020 Project: Bucknell University Project No. CFB CFB RFI No. 020 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. 2 ISSUE DATE: 3/28/17 INQUIRER: Stephen Thaler CO. NAME : Lundy Construction E MAIL: swt@lundyconstruction.com Phone : Ext 103 RFI DESCRIPTION: LEED Commissioning Cost RFI : Page of 26 paragraph C.1. indicates Owner will engage the Commissioning Authority under a separate contract.» Then under 1.10 General Contractor Responsibilities item 10 indicates Include cost of commissioning in the total contract price. Will the General Contractor be required to cover all of the commissioning costs including the cost of the Commissioning Authority engaged by the Owner or does the General Contractor include only the cost of their defined responsibilities for the commissioning process? REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: SECTION COMMISSSIONING SPECIFICATIONS The Owner will pay for the independent commissioning agent. The Contractor include only costs of their defined responsibilities for the commissioning process. Refer to and 1.11 of specifications. RESPONDER: JSW DATE: 3/28/17

20 RFI 021 Project: Bucknell University Project No. CFB CFB RFI No. 021 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. P1 ISSUE DATE: INQUIRER: Brett Lazicki CO. NAME : Silvertip Inc E MAIL: estimating@silvertip inc.com Phone : RFI DESCRIPTION: Bucknell Demosthenean Hall RFI : 1. Plumbing scope , 1.2A. item 6. Basic Plumbing Materials , 1.2B Please confirm that this project is a single prime contractor and that the sprinkler contractor will not be a sub contract of the plumber. 2. Plumbing scope , 1.2A. item 8. Please confirm that this item is not applicable to this project. (pool piping) REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: 1. The sprinkler contractor will not be a sub contract of the plumber. 2. The pool piping item shall be removed from the scope via Addendum. RESPONDER: CFB/CJL DATE: 3/28/17

21 RFI022 Project: Bucknell University Project No. CFB CFB RFI No. 022 Celli Flynn Brennan Architects & Planners Phone: INQUIRER S RFI NO. P2 ISSUE DATE: INQUIRER: Brett Lazicki CO. NAME : Silvertip Inc E MAIL: estimating@silvertip inc.com Phone : RFI DESCRIPTION: Bucknell Demosthenean Hall RFI : 1. Per the INVITATION TO BID, page 1, section 1.4 «PREBID CONFERENCE» Please confirm that only contractors that attended the MANDATORY Prebid Conference will be allowed to bid. According to the specification that applies to GC and all MEP contractors. REFERENCES/ ATTACHMENTS: (List specific documents researched when seeking the information requested.) SPECIFICATIONS: DRAWINGS: OTHER: The Owner has elected to waive the mandatory pre bid requirement. RESPONDER: Bucknell University DATE: 3/28/17