FIRESTOP SUBMITTAL PACKAGE

Transcription

1 FIRESTOP SUBMITTAL PACKAGE Perimeter Fire Containment Systems Project: Date: Submitted by: 210 Evans Way Somerville, NJ (800) (908) Fax (908)

2 GENERAL CERTIFICATE OF CONFORMANCE JUNE 2013 Description: SpecSeal Firestop Products; Pensil Silicone Sealants; EZ-Path Fire Rated Pathways; Ready Sleeve Firestop Sleeves; STI Firestop Products Included Products: SpecSeal Series SSS Intumescent Sealant SpecSeal Series LCI Intumescent Sealant SpecSeal Series LC Firestop Sealant SpecSeal Series ES Elastomeric Sealant SpecSeal Series SIL300 Silicone Sealant SpecSeal Series SIL300SL Silicone Sealant Pensil PEN300 Silicone Sealant Pensil PEN300SL Silicone Sealant Pensil PEN200 Silicone Foam BlazeStop WF300 Firestop Caulk SpecSeal Series AS200 Elastomeric Spray SpecSeal Series FT Fast Tack Firestop Spray SpecSeal Series SSP Putty & Putty Pads SpecSeal Series EP PowerShield Box Insert SpecSeal Series SSM Firestop Mortar SpecSeal Series SSB Firestop Pillows SpecSeal Series CS Composite Sheet SpecSeal Series SSW Wrap Strips SpecSeal Series LCC Firestop Collars SpecSeal Series SSC Firestop Collars SpecSeal Series RTC Firestop Collars SpecSeal Series FP Firestop Plugs SpecSeal Series CD Cast-In Firestop Devices FyreFlange Firestop Angle EZ-Path Series 22 EZ-Path Series 33 EZ-Path Series 44 or 44+ Ready Sleeve Ready Sleeve Split EZ-Path Firestop Grommet SpecSeal Series SSAMW Mineral Wool SpecSeal SpeedFlex Fire Rated Joint Profile SpecSeal Closet Flange Firestop Gasket SpecSeal Series CS105 Cable Spray SpecSeal SpeedFlex Track Top Gasket These products are tested to one or more of the following standards: ASTM E814 (ANSI/UL1479) Standard Test Method for Fire Tests of Penetration Firestop Systems ASTM E1966 (ANSI/UL2079) Standard Test Method for Fire-Resistive Joint Systems ASTM E119 (ANSI/UL263) Standard Test Methods for Fire Tests of Building Construction and Materials ASTM E2307 Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems Using Intermediate Scale, Multi-Story Test Apparatus ASTM E1399 Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems ASTM E84 (ANSI/UL723) Standard Test Method for Surface Burning Characteristics of Building Materials CAN/ULC S115 Standard Method of Fire Tests of Firestop Systems CAN/ULC S101 Standard Methods of Fire Endurance Tests of Building Construction and Materials Chemical Content Statement: No asbestos, PCB s, lead, or water-soluble intumescent ingredients are used or contained in these products. James P. Stahl Jr., CFPS Vice President of Engineering Paul M. Jankowski Quality Control Manager Certificate of Conformance Technical Service

3 F Rating - 2 Hr T Rating - 1/2 Hr Linear Opening Width - 1 In. Max L Rating At 400 F - Less Than 1 CFM/Lin Ft Ì86CWSÇ*#ÈAOÇ"<.[Î 2D 3A 3B 2B 2F 2E 1 2A 2E 2G 2C 2D 1. Floor Assembly - Min 4-1/2 in. (114 mm) thick reinforced lightweight or normal weight ( pcf or kg/m3) structural concrete slab. 2. Curtain Wall Assembly - The curtain wall assembly shall incorporate the following construction features: A. Steel Floor and Ceiling Runners - Floor and ceiling runners of wall assembly shall consist of channels sized to accommodate steel studs and formed from min 25 gauge (min in. or 0.64 mm thick) galv steel. Steel runner channels installed to extend max 1 in. (25 mm) beyond edge of slab and secured to slab with steel masonry anchors spaced max 16 in. (406 mm) OC. B. Steel Studs - C-shaped studs formed from min 25 gauge (min in. or 0.64 mm thick) galv steel. The steel studs shall be min 6 in. (152 mm) wide by 1-1/4 in. (31 mm) deep with 5/16 in. (8 mm) wide stiffening flanges. Studs spaced max 16 in. (406 mm) OC and fastened to steel runner channels with steel screws or welds. B1. King Studs - (Optional, Not Shown) - Where required, a king stud may be substituted for Item 2b. King studs to consist of two min 6 in. (152 mm) wide by 1-1/4 in. (31 mm) deep C-shaped studs formed from min 25 gauge (min in. or 0.64 mm thick) galv steel secured together by welds. C. Gypsum Board* - One layer of nom 5/8 in. (16 mm) thick, 48 in. (1.2 m) wide gypsum sheathing installed to cover entire exterior surface of wall. Sheathing applied with joints centered over studs and secured to steel studs with min 1 in. (25 mm) long bugle head steel screws spaced max 8 in. (203 mm) OC along the edges and max 12 in. (305 mm) OC in the field of each sheet. See Gypsum Board (CKNX) category for names of Classified Companies and product types. C1. Cementitious Backer Units* - As an alternate to the gypsum sheathing (Item 2C), nom 1/2 in. or 5/8 in. (13 or 16 mm) thick square-edge boards attached to studs with 1-1/4 in. (31 mm) long corrosion resistant self-tapping wafer-head steel screws spaced 6 in. (152 mm) OC. Joints covered with glass fiber mesh tape. UNITED STATES GYPSUM CO - Type DCB Reproduced courtesy of Underwriters Laboratories, Inc. Created or Revised: February 28, 2014 (800) (908) FAX (908) techserv@stifirestop.com Website: R CW-S-0003 PAGE 1 OF 2

4 D. Batts and Blankets* - Any glass fiber insulation bearing the UL Classification Marking as to fire resistance or surface burning characteristics, of a width and thickness to completely fill stud cavity. Insulation batts friction fit to completely fill all stud cavities of curtain wall above the top of the fill material (Item 3B) and below the forming material (Item 3A). See Batts and Blankets (BZJZ) category for names of manufacturers. E. Gypsum Board* - One layer of nom 5/8 in. (16 mm) thick, 48 in. (1.2 m) wide gypsum board applied with joints centered over studs. Gypsum board secured to steel studs on interior surface of curtain wall with min 1 in. (25 mm) long bugle head steel screws spaced max 8 in. (203 mm) OC along the edges and max 12 in. (305 mm) OC in the field of each sheet. Gypsum board installed to cover interior surface of wall above the top of the fill material (Item 3C) for a min distance of 4-1/2 in. (114 mm). See Gypsum Board (CKNX) category for names of Classified Companies and product types. F. Framed Window - Metal-framed window with nom 1 in. (25 mm) thick (double pane) transparent heat-strengthened or tempered glass panels. Sill of window to be min 4-1/2 in. (114 mm) above top of floor slab. Vertical separation between window punch-outs to be min 36 in. (914 mm). Top of window to be min 24 in. (610 mm) below bottom of floor slab. G. Exterior Insulation and Finish System (EIFS) - Nom 2 in. (51 mm) thick extruded polystyrene Foamed Plastic* insulation bearing the UL Classification Marking, attached over sheathing and finished with coating system, or Portland cement or synthetic stucco systems, in accordance with manufacturer's instructions. See Foamed Plastic (BRYX or CCVW) category for names of Classified companies. H. Siding, Brick or Stucco - (Not Shown) - Aluminum siding, steel siding, brick veneer or stucco installed over gypsum sheathing or cementitious backer units and meeting the requirements of local code agencies. Brick veneer wall attached to studs with corrugated metal wall ties attached to each stud with steel screws. I. Glass Fiber Reinforced Concrete (GFRC) Panels - (Not Shown) - Min 1/2 in. (13 mm) thick glass fiber reinforced concrete (GFRC) panels installed over gypsum sheathing or cementitious backer units and meeting the requirements of local code agencies. 3. Safing System - The safing system shall incorporate the following construction features: A. Forming Material* - Nom 4 pcf (64 kg/m3) mineral wool batt insulation cut to a width nominally 1/2 in. (13 mm) wider than width of stud cavity and the on-center spacing between the vertical studs. Forming material friction-fitted into steel runner channel on top surface of floor to min 4 in. (102 mm) depth. ROCKWOOL MALAYSIA SDN BHD - Safe ROXUL INC - Safe THERMAFIBER INC - SAF B. Fill, Void or Cavity Material* - Spray - Min 1/8 in. (3.2 mm) wet thickness (min 1/16 in. or 1.6 mm dry thickness) of fill material spray-applied atop mineral wool safing (Item 3A) with min 1/2 in. (13 mm) overlap onto sheathing, steel studs, and concrete floor. SPECIFIED TECHNOLOGIES INC - SpecSeal AS200 Elastomeric Spray or SpecSeal Fast Tack Spray *Bearing the UL Classification Mark Reproduced courtesy of Underwriters Laboratories, Inc. Created or Revised: February 28, 2014 (800) (908) FAX (908) techserv@stifirestop.com Website: R CW-S-0003 PAGE 2OF 2

5 F Rating - 2 Hr T Ratings - 0 and 1/2 Hr (See Item 2K) Linear Opening Width - 2-1/2 In. Max L Rating At Ambient - Less Than 1 CFM/Lin Ft L Rating At 400 F - Less Than 1 CFM/Lin Ft 2B Ì79CWSÇ*3ÈAOÇ"<.yÎ 2B 2G 2F 3B 2C 2D 2E 1 2H 3A 2E 1. Floor Assembly - Min 4-1/2 in. (114 mm) thick reinforced lightweight or normal weight ( pcf or kg/m3) structural concrete. Perimeter of floor assembly to be provided with min 3 by 3 by 1/4 in. (76 by 76 by 6 mm) thick cast-in-place structural steel angle for weld-attachment of mounting angles (Item 2A). 2. Curtain Wall Assembly - The curtain wall assembly shall incorporate the following construction features: A. Mounting Angles - (Not Shown) - Nom 3 in. (76 mm) long angles with one nom 3 in. (76 mm) leg for attachment to edge of floor assembly and with one leg approx 2-1/2 to 3 in. (64 to 76 mm) longer than distance to interior face of steel studs. Angles to be formed of min 1/8 in. (3.2 mm) thick steel. Angles welded to cast-in-place structural steel angle at edge of floor assembly (Item 1) on one side of each steel stud (Item 2B) at each floor level. Top edge of each mounting angle to be recessed 1/2 to 1 in. (13 to 25 mm) below top surface of floor. B. Steel Studs - C-shaped studs formed from min in. (1.5 mm) thick galv steel. The steel studs shall be min 6 in. (152 mm) wide by 1-1/4 in. (31 mm) deep with 5/16 in. (8 mm) wide stiffening flanges and shall be assembled using runner channels formed from min in. (1.5 mm) thick galv steel. Studs spaced max 16 in. (406 mm) OC and welded, bolted or screwed to mounting angles (Item 2A) at each floor level. Interior face of studs to be max 2-1/2 in. (64 mm) from edge of floor assembly. Studs reinforced by means of nom 1-1/2 in. (38 mm) wide by 9/16 in. (14 mm) deep min in. (1.5 mm) thick cold rolled steel channels inserted through steel stud keyways on max 48 in. (1.2 m) centers and welded to steel studs. B1. King Studs - (Optional, Not Shown) - Where required, a king stud may be substituted for Item 2B. King studs to consist of two min 6 in. (152 mm) wide by 1-1/4 in. (31 mm) deep C-shaped studs formed from min in. (1.5 mm) thick galv steel secured together by welds. See Item 3C. C. Gypsum Board* - One layer of nom 5/8 in. (16 mm) thick, 48 in. (1.2 m) wide gypsum sheathing installed to cover entire exterior surface of wall. Sheathing applied with joints centered over studs and secured to steel studs with min 1 in. (25 mm) long bugle head steel screws spaced max 8 in. (204 mm) OC along the edges and max 12 in. (305 mm) OC in the field of each sheet. See Gypsum Board (CKNX) category for names of Classified Companies and product types. D. Cementitious Backer Units* - As an alternate to the gypsum sheathing (Item 2C), nom 1/2 in. or 5/8 in. (13 or 16 mm) thick square-edge boards attached to studs with 1-1/4 in. (31 mm) long corrosion resistant self-tapping wafer-head steel screws spaced 6 in. (152 mm) OC. Joints covered with glass fiber mesh tape. UNITED STATES GYPSUM CO - Type DCB 2G Reproduced courtesy of Underwriters Laboratories, Inc. Created or Revised: February 28, 2014 (800) (908) FAX (908) techserv@stifirestop.com Website: R CW-S-1019 PAGE 1OF 2

6 E. Batts and Blankets* - Any glass fiber insulation bearing the UL Classification Marking as to fire resistance or surface burning characteristics, of a width and thickness to completely fill stud cavity. Insulation batts friction fit to completely fill all stud cavities of curtain wall above the top of the fill material (Item B) and below the forming material (Item 3A). See Batts and Blankets (BZJZ) category for names of manufacturers. F. Gypsum Board* - One layer of nom 5/8 in. (16 mm) thick, 48 in. (1.2 m) wide gypsum board applied with joints centered over studs. Gypsum board secured to steel studs on interior surface of curtain wall with min 1 in. (25 mm) long bugle head steel screws spaced max 8 in. (204 mm) OC along the edges and max 12 in. (305 mm) OC in the field of each sheet. Gypsum board installed to cover interior surface of wall above the top of the fill material (Item 3C) for a min distance of 6 in. (152 mm). Gypsum board is optional below floor assembly. See Gypsum Board (CKNX) category for names of Classified Companies and product types. G. Framed Window - Metal-framed window with nom 1 in. (25 mm) thick (double pane) transparent heat-strengthened or tempered glass panels. Sill of window to be min 6 in. (152 mm) above top of floor slab. Vertical separation between window punch-outs to be min 36 in. (914 mm). Top of window to be min 22-1/2 in. (572 mm) below bottom of floor slab. H. Exterior Insulation and Finish System (EIFS) - Nom 2 in. (51 mm) thick extruded polystyrene Foamed Plastic* insulation bearing the UL Classification Marking, attached over sheathing and finished with coating system, or Portland cement or synthetic stucco systems, in accordance with manufacturer's instructions. See Foamed Plastic (BRYX or CCVW) category for names of Classified companies. I. Siding, Brick or Stucco - (Not Shown) - Aluminum siding, steel siding, brick veneer or stucco installed over gypsum sheathing or cementitious backer units and meeting the requirements of local code agencies. Brick veneer wall attached to studs with corrugated metal wall ties attached to each stud with steel screws. J. Glass Fiber Reinforced Concrete (GFRC) Panels - (Not Shown) - Min 1/2 in. (13 mm) thick glass fiber reinforced concrete (GFRC) panels installed over gypsum sheathing or cementitious backer units and meeting the requirements of local code agencies. K. Through Penetrant - (Optional, Not Shown) - Nom 1 in. (25 mm) diam rigid Sch 5 (or heavier) steel pipe, Regular (or heavier copper pipe, or Type M (or heavier) copper tube, steel conduit, steel electrical metallic tubing (EMT), flexible steel conduit, Sch 40 PVC conduit, or max 3/C-10 AWG (or smaller) metal-clad cable may be installed within the stud cavity. The through penetrant shall be located approximately midway between studs and nominally centered within the depth of stud. A max of one through penetrant is permitted in an individual stud cavity. When through penetrant is installed in stud cavity, the hourly T Rating of the perimeter fire containment system is 0 hr. 3. Safing System - The safing system shall incorporate the following construction features: A. Forming Material* - Nom 4 pcf (64 kg/m3) density mineral wool batt insulation. Batt sections to be cut to a min width of 4 in. (102 mm) and stacked to a thickness which is 25 percent greater than the width of linear gap between the gypsum sheathing and the edge of the concrete floor to attain a min 20 percent compression in the thickness direction when installed. The forming material is compressed and inserted cut-edge-first into linear gap between edge of floor slab and sheathing material such that its top surface is flush with the top surface of the floor assembly. Length of batt to be equal to on-center spacing of steel studs such that it is friction-fitted between studs and mounting angles without seams. Additional pieces of mineral wool batt to be stuffed inside the channel of each steel stud throughout the thickness of the forming material. THERMAFIBER INC - SAF B. Fill, Void or Cavity Material* - Spray - Min 1/8 in. (3.2 mm) wet thickness (min 1/16 in. or 1.6 mm dry thickness) of fill material spray-applied over top of forming material and lapping min 1/2 in. (13 mm) onto the top surface of the floor and onto the gypsum sheathing and steel studs and optional through penetrant (Item 2K). SPECIFIED TECHNOLOGIES INC - SpecSeal AS200 Elastomeric Spray or SpecSeal Fast Tack Spray C. Fill, Void or Cavity Material* - Pillows - (Not Shown) - Where king studs (Item 2B1) are located, channel within stud to be sealed with pillows. Max 9 in. long by 6 in. wide by 3 in. thick plastic covered intumescent pillows compressed and tightly packed into channel at each floor line. SPECIFIED TECHNOLOGIES INC - SpecSeal Firestop Pillows *Bearing the UL Classification Mark Reproduced courtesy of Underwriters Laboratories, Inc. Created or Revised: February 28, 2014 (800) (908) FAX (908) techserv@stifirestop.com Website: R CW-S-1019 PAGE 2OF 2

7 F Rating - 2 Hr T Rating -1/2 Hr Linear Opening Width - 2-1/2 In. Max Class II Movement Capabilities - 5% Vertical Shear L Rating At Ambient - Less Than 1 CFM/Lin Ft L Rating At 400 F - Less Than 1 CFM/Lin Ft Ì87CWDÇ*+ÈAOÇ"<.RÎ 2B 2B 2G 2F 3B 2C 2D 2E 1 2H 3A 2E 2G 1. Floor Assembly - Min 4-1/2 in. (114 mm) thick reinforced lightweight or normal weight ( pcf or kg/m3) structural concrete. Perimeter of floor assembly to be provided with min 3 by 3 by 1/4 in. (76 by 76 by 6 mm) thick cast-in-place structural steel angle for weld-attachment of mounting angles (Item 2A). 2. Curtain Wall Assembly - The curtain wall assembly shall incorporate the following construction features: A. Mounting Angles - (Not Shown) - Nom 3 in. (76 mm) long angles with one nom 3 in. (76 mm) leg for attachment to edge of floor assembly and with one leg approx 2-1/2 to 3 in. (64 to 76 mm) longer than distance to interior face of steel studs. Angles to be formed of min 1/8 in. (3.2 mm) thick steel. Angles welded to cast-in-place structural steel angle at edge of floor assembly (Item 1) on one side of each steel stud (Item 2B) at each floor level. Top edge of each mounting angle to be recessed 1/2 to 1 in. (13 to 25 mm) below top surface of floor. B. Steel Studs - C-shaped studs formed from min in. (1.5 mm) thick galv steel. The steel studs shall be min 6 in. (152 mm) wide by 1-1/4 in. (31 mm) deep with 5/16 in. (8 mm) wide stiffening flanges and shall be assembled using runner channels formed from min in. (1.5 mm) thick galv steel. Studs spaced max 16 in. (406 mm) OC and welded, bolted or screwed to mounting angles (Item 2A) at each floor level. To allow for designed amount of movement, elongated holes may be integrated into either the mounting angle (Item 2A) or the stud (Item 2B). Interior face of studs to be max 2-1/2 in. (64 mm) from edge of floor assembly. Studs reinforced by means of nom 1-1/2 in. (38 mm) wide by 9/16 in. (14 mm) deep min in. (1.5 mm) thick cold rolled steel channels inserted through steel stud keyways on max 48 in. (1.2 m) centers and welded to steel studs. B1. King Studs - (Optional, Not Shown) - Where required, a king stud may be substituted for Item 2B. King studs to consist of two min 6 in. (152 mm) wide by 1-1/4 in. (31 mm) deep C-shaped studs formed from min in. (1.5 mm) thick galv steel secured together by welds. See Item 3C. C. Gypsum Board* - One layer of nom 5/8 in. (16 mm) thick, 48 in. (1.2 m) wide gypsum sheathing installed to cover entire exterior surface of wall. Sheathing applied with joints centered over studs and secured to steel studs with min 1 in. (25 mm) long bugle head steel screws spaced max 8 in. (204 mm) OC along the edges and max 12 in. (305 mm) OC in the field of each sheet. See Gypsum Board (CKNX) category for names of Classified Companies and product types. Reproduced courtesy of Underwriters Laboratories, Inc. Created or Revised: February 28, 2014 (800) (908) FAX (908) techserv@stifirestop.com Website: R CW-D-1011 PAGE 1 OF 2

8 D. Cementitious Backer Units* - As an alternate to the gypsum sheathing (Item 2C), nom 1/2 in. or 5/8 in. (13 or 16 mm) thick square-edge boards attached to studs with 1-1/4 in. (31 mm) long corrosion resistant self-tapping wafer-head steel screws spaced 6 in. (152 mm) OC. Joints covered with glass fiber mesh tape. UNITED STATES GYPSUM CO - Type DCB E. Batts and Blankets* - Any glass fiber insulation bearing the UL Classification Marking as to fire resistance or surface burning characteristics, of a width and thickness to completely fill stud cavity. Insulation batts friction fit to completely fill all stud cavities of curtain wall above the top of the fill material (Item B) and below the forming material (Item 3A). See Batts and Blankets (BZJZ) category for names of manufacturers. F. Gypsum Board* - One layer of nom 5/8 in. (16 mm) thick, 48 in. (1.2 m) wide gypsum board applied with joints centered over studs. Gypsum board secured to steel studs on interior surface of curtain wall with min 1 in. (25 mm) long bugle head steel screws spaced max 8 in. (204 mm) OC along the edges and max 12 in. (305 mm) OC in the field of each sheet. Gypsum board installed to cover interior surface of wall above the top of the fill material (Item 3C) for a min distance of 6 in. (152 mm). Gypsum board is optional below floor assembly. See Gypsum Board (CKNX) category for names of Classified Companies and product types. G. Framed Window - Metal-framed window with nom 1 in. (25 mm) thick (double pane) transparent heat-strengthened or tempered glass panels. Sill of window to be min 6 in. (152 mm) above top of floor slab. Vertical separation between window punch-outs to be min 36 in. (914 mm). Top of window to be min 22-1/2 in. (572 mm) below bottom of floor slab. H. Exterior Insulation and Finish System (EIFS) - Nom 2 in. (51 mm) thick extruded polystyrene Foamed Plastic* insulation bearing the UL Classification Marking, attached over sheathing and finished with coating system, or Portland cement or synthetic stucco systems, in accordance with manufacturer's instructions. See Foamed Plastic (BRYX or CCVW) category for names of Classified companies. I. Siding, Brick or Stucco - (Not Shown) - Aluminum siding, steel siding, brick veneer or stucco installed over gypsum sheathing or cementitious backer units and meeting the requirements of local code agencies. Brick veneer wall attached to studs with corrugated metal wall ties attached to each stud with steel screws. J. Glass Fiber Reinforced Concrete (GFRC) Panels - (Not Shown) - Min 1/2 in. (13 mm) thick glass fiber reinforced concrete (GFRC) panels installed over gypsum sheathing or cementitious backer units and meeting the requirements of local code agencies. 3. Safing System - Max separation between edge of floor assembly and face of framing members is 2-1/2 in. (64 mm). The safing system is designed to accommodate vertical shear movement up to a max of 5 percent of its installed width. The safing system shall incorporate the following construction features: A. Forming Material* - Nom 4 pcf (64 kg/m3) density mineral wool batt insulation. Batt sections to be cut to a min width of 4 in. (102 mm) and stacked to a thickness which is 25 percent greater than the width of linear gap between the gypsum sheathing and the edge of the concrete floor to attain a min 20 percent compression in the thickness direction when installed. The forming material is compressed and inserted cut-edge-first into linear gap between edge of floor slab and sheathing material such that its top surface is flush with the top surface of the floor assembly. Length of batt to be equal to on-center spacing of steel studs such that it is friction-fitted between studs and mounting angles without seams. Additional pieces of mineral wool batt to be stuffed inside the channel of each steel stud throughout the thickness of the forming material. THERMAFIBER INC - SAF B. Fill, Void or Cavity Material* - Spray - Min 1/8 in. (3.2 mm) wet thickness (min 1/16 in. or 1.6 mm dry thickness) of fill material spray-applied over top of forming material and lapping min 1/2 in. (13 mm) onto the top surface of the floor and onto the gypsum sheathing and steel studs. SPECIFIED TECHNOLOGIES INC - SpecSeal AS200 Elastomeric Spray or SpecSeal Fast Tack Spray C. Fill, Void or Cavity Material* - Pillows - (Not Shown) - Where king studs (Item 2B1) are located, channel within stud to be sealed with pillows. Max 9 in. long by 6 in. wide by 3 in. thick plastic covered intumescent pillows compressed and tightly packed into channel at each floor line. SPECIFIED TECHNOLOGIES INC - SpecSeal Firestop Pillows *Bearing the UL Classification Mark Reproduced courtesy of Underwriters Laboratories, Inc. Created or Revised: February 28, 2014 (800) (908) FAX (908) techserv@stifirestop.com Website: R CW-D-1011 PAGE 2 OF 2

9 PRODUCT DATA SHEET SERIES AS200 ELASTOMERIC SPRAY APPLICATIONS SpecSeal Elastomeric Spray is designed primarily for the protection of construction joints, curtain wall safing gaps, and certain through-penetrations. PRODUCT DESCRIPTION SpecSeal Series AS200 Elastomeric Spray is a non-halogenated latex-based, highly elastomeric coating designed to provide passive smoke and fire protection in construction joints. SpecSeal Series AS200 Elastomeric Spray is engineered to adhere to virtually all construction surfaces and may be applied using airless spray equipment or with a brush (ideally for, but not limited to, small applications or touch ups). SpecSeal Series AS200 Elastomeric Spray dries to form a flexible shield against the propagation of fire. Its premium latex binder system is totally resistant to water and will not re-emulsify after drying. SpecSeal Series AS200 Elastomeric Spray contains no inorganic fibers, asbestos, solvents. FEATURES PERFORMANCE Water-Based for easy installation and cleanup Non-halogenated. Thixotropic for high-build application. Auto Bonding. Safe... no solvents! No asbestos! Flexible! Water Resistant! Low Abrasion for longer pump life and less maintenance. UL Classified. Tested with spray applied fire resistive materials (SFRM). Paintable When applied to a wet film thickness of 1/8" (3.2 mm) over appropriate backing materials, SpecSeal Series AS200 Elastomeric Spray has been successfully tested in one, two, three and four hour joints tested in accordance with ASTM E1966 (ANSI/UL2079) and CAN/ULCS115. This product has also been tested for use in Perimeter Fire Barrier Systems in accordance with ASTM E2307. Consult factory for individual system designs and application requirements. LIMITATIONS: Use product as per manufacturer s instructions. Use only in applications per the manufacturer s tested and published designs or specific recommendations. End user must ultimately determine the suitability of the product and designs to his specific requirement and assumes responsibility for its use. PRODUCT CONTAINS WATER AND IS CONDUCTIVE UNTIL DRY. DO NOT APPLY IN THE PRESENCE OF EXPOSED OR ENERGIZED ELECTRICAL CONDUCTORS. FILL, VOID OR CAVITY MATERIALS FOR USE IN JOINT SYSTEMS & THROUGHPENETRATION FIRESTOP SYSTEMS. SEE UL FIRE RESISTANCE DIRECTORY. 3L73 FBC System Compatible indicates that this product has been tested, and is monitored on an ongoing basis, to assure its chemical compatibility with FlowGuard Gold, BlazeMaster and Corzan pipe and fittings. FBC, FlowGuard Gold, BlazeMaster and Corzan are licensed trademarks of The Lubrizol Corporation. PHYSICAL PROPERTIES PROPERTIES: SERIES AS SPRAY Color Pale Blue and Red Odor Mild Latex Specific Gravity 1.3 Solids Content by Weight Solids Content by Volume 74% 66.4% Flame Spread 0* Smoke Developed 25* Movement ±50%** Coverage 12.8 sq 1/8 (0.31 sq 3.2 mm) Viscosity 110,000 cps ph 7.5 PROPERTIES: SERIES AS SPRAY Solvent Content Plasticizer None None In-Service Temp. 185 F (85 C) Storage Temp. Drying Time 40 F (4 C) - 95 F (35 C) Tack Free 2 Hours Dry Through Hours A STC Rating 61 VOC Content B Shelf Life * Tested to ASTM E84 14% coverage. **500 Cycles per UL2079, AC30 (ICBO) and ASTM E1399 A Dependent on temperature and humidity. B Per ASTM D3960 EPA Fed. Reference Method g/l 18 Months Technical Service STI Product Data Sheet Series AS200 Elastomeric Spray FOD

10 FIG. 1: METALLIC PIPE PENETRATIONS - CONCRETE/MASONRY FLOORS & WALLS UL System No. C-AJ-1318 F Rating 2 Hr T Rating 0 Hr Steel or Iron Pipe: <12", Copper Pipe: <6" Annulus: Point Contact to 2" Forming Material: Nom 4 pcf mineral wool to 4" depth Spray Depth: 1/8" wet depth (+1/2" overlap) FIG. 2: SLAB-EDGE SAFING GAP APPLICATIONS UL System No. CW-S-2061 F Rating 2 Hr T Rating 1/4 Hr Linear Opening Width - 8 In Max L Rating At Ambient - Less than 1 CFM/Lin Ft L Rating At 400 o F - Less Than 1 CFM/Lin Ft FIG. 3: HEAD-OF-WALL APPLICATIONS UL System No. HW-D-0043 Assembly Ratings - 1,2,3 and 4 Hr. Nominal Joint Widths - 1 and 2 In. L Rating At Ambient - Less than 1 CFM/Lin Ft. L Rating At 400 o F - Less Than 1 CFM/Lin Ft. Class II Movement Capabilities - 40 or 50% Compression and extension. 2 STI Product Data Sheet Series AS200 Elastomeric Spray FOD Technical Service

11 SPECIFICATIONS The fire protective joint coating shall be a water-based, non-halogenated elastomeric coating and shall contain no solvents, inorganic fibers, nor asbestos. The coating shall dry to form a flexible, moisture resistant film and shall adhere to all common construction surfaces. The coating shall provide up to 50 percent movement. The coating shall be thixotropic and shall be capable of being applied by brush or by airless spray. The approved coating shall be SpecSeal Series AS200 Elastomeric Spray. SPECIFIED DIVISIONS DIV Through-Penetration Firestopping DIV Concrete Unit Masonry DIV Thermal Insulation DIV Curtain Wall and Glazed Assemblies INSTALLATION INSTRUCTIONS GENERAL: Areas to be protected must be clean and free of oil, loose dirt, rust or scale. Recommended storage temperatures range between 40 F (4 C) and 95 F (35 C). Installation temperature shall be between 40 F (4 C) and 95 F (35 C). Although not a requirement, the optimal application temperature range is 60 F (16 C) to 90 F (32 C). When applying product at the lower end of the temperature range, warming the material to 70 F (21 C) will enhance drying characteristics. Drying time will vary according to prevailing temperature and humidity. Allow to thoroughly dry before exposure to moisture. Consult appropriate manufacturer s drawing for system design requirements. Forming or packing materials are required as an integral part of various system designs. Coating may be applied by airless spray in a single pass up to 3/16" (4.8mm) wet coating depth. If applying by brush or spraying on vertical surfaces where coating appears to be prone to slumping, multiple coats or the application of a thin tack coat may be required. DO NOT ATTEMPT TO THIN PRODUCT BY ADDING WATER. When dry, may be painted using most non-solvent based paints. MAINTENANCE Inspection: Installations should be inspected periodically for subsequent damage. Following safety precautions listed below (See Precautionary Information) and pertinent installation guidelines, remove coating in damaged areas down to undamaged material. Reapply fresh coating material to original coating thickness. TECHNICAL SERVICE Specified Technologies Inc. provides toll free technical support to assist in product selection and appropriate installation design. UL Systems, Material Safety Data Sheets and other technical information is available at the Technical Library at PRECAUTIONARY INFORMATION Consult Material Safety Data Sheet for additional information on the safe handling and disposal of this material. Wash areas of skin contact with soap and water. Avoid contact with eyes. The use of an OSHA or NIOSH approved mask for dust and mist environment is recommended. Apply in areas with adequate ventilation. AVAILABILITY SpecSeal Series AS200 Elastomeric Spray is available worldwide from authorized distributors. Consult factory for the names and locations of the nearest sales representatives or distributors.. Technical Service STI Product Data Sheet Series AS200 Elastomeric Spray FOD

12 TABLE A: APPLICATION EQUIPMENT NOTICE: Spray application of SpecSeal Elastomeric Spray requires airless spray equipment meeting the following specifications: Working Pressure: Min PSI (172 Bar) Delivery: Min..72 U.S. gpm (2.7 l/min.) recommended Spray Tip Orifice: to (0.58 to 0.66 mm) recommended Wetted Parts All seals and contact surfaces suitable for contact with latex emulsions. A minimum 3/8 (9.5 mm) fluid line is required, a 1/2 (13 mm) line is preferred. Consult pump manufacturer for long hose runs or lifts to higher elevations. A reversible spray tip is recommended. A 6 (152 mm) fan pattern is suggested to minimize overspray. The following airless spray equipment has demonstrated suitability for application of this product. STI makes no warranties concerning the suitability or use of this equipment and has no affiliation of any kind with its manufacturer. Manufacturer Titan Tool Inc. Graco Inc. Model Number & Description 740ix Electric Airless Sprayer Ultra Max II 695 Electric Airless Sprayer ORDERING INFORMATION SpecSeal Elastomeric Spray is available in 5 gal. pails, 55 gal. drums are available on a special order basis. AS205 Pale Blue Color 5 gal. Pail 1,155 cu. in. (19 liters) AS205R Red Color 5 gal. Pail 1,155 cu. in. (19 liters) CITY OF NEW YORK MEA M Important Notice: All statements, technical information, and recommendations contained herein are based upon testing believed to be reliable, but the accuracy and completeness thereof is not guaranteed. WARRANTY: Specified Technologies Inc. manufactures its goods in a manner to be free of defects. Should any defect occur in its goods (within one year), Specified Technologies Inc., upon prompt notification, will at its option, exchange or repair the goods or refund the purchase price. Limitations and Exclusions: THIS WARRANTY IS IN LIEU OF ALL OTHER REPRESENTATIONS EXPRESSED OR IMPLIED (INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR USE) AND UNDER NO CIRCUMSTANCES SHALL SPECIFIED TECHNOLOGIES INC. BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL PROPERTY DAMAGE OR LOSSES. PRIOR TO USE, THE USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR ITS INTENDED USE, AND THE USER ASSUMES ALL RISKS AND LIABILITY FOR SUBSEQUENT USE. No statement or recommendation not contained herein shall have any force or effect unless in an agreement signed by officers of seller and manufacturer. MADE IN THE USA COPYRIGHT 2012 SPECIFIED TECHNOLOGIES INC. 210 Evans Way, Somerville NJ USA Phone: Fax: STI Product Data Sheet Series AS200 Elast Spray FOD /2012 Technical Service

13 PRODUCT DATA SHEET FAST TACK FIRESTOP SPRAY APPLICATIONS SpecSeal Fast Tack Firestop Spray is designed primarily for the protection of construction joints and excels in curtain wall safing gap conditions. Slab/edge/curtain wall conditions Floor to floor joints Floor to wall joints PRODUCT DESCRIPTION SpecSeal Fast Tack Firestop Spray is an elastomeric single component silicone/urethane hybrid spray coating designed to provide passive smoke and fire protection in construction joints. SpecSeal Fast Tack Firestop Spray is engineered to adhere to common construction substrates and may be applied using airless spray equipment or with a brush (for small applications or touch ups). As an option, SpecSeal Fast Tack Firestop Spray may also be used as a self-leveling sealant and poured into the linear opening to the required thickness as specified in the individual UL System design. SpecSeal Fast Tack Firestop Spray dries rapidly and cures in the presence of atmospheric moisture to form a durable, flexible, water-resistant shield against the propagation of fire, smoke and combustion byproducts. SpecSeal Fast Tack Firestop Spray does not contain asbestos or PCB s. PERFORMANCE FEATURES Skins over quickly to resist water! Tack free in 2-4 hours! Cures below freezing. Tough, water-resistant flexible shield against fire and smoke. Will Not Wash Out! When applied to a wet film thickness of 1/8 (3.2 mm) over appropriate backing materials, SpecSeal Fast Tack Firestop Spray has been successfully tested to the exacting criteria of ASTM E 2307, ASTM E 1966, ANSI/UL2079, ASTM E 1399 and to the time-temperature requirements of ASTM E 119 (ANSI/UL 263) in one, two and three hour rated joint and perimeter fire containment systems. Visit the Technical Library at for individual UL System designs and application requirements. LIMITATIONS: Use product as per manufacturer s instructions. Use only in applications per the manufacturer s tested and published designs or specific recommendations. End user must ultimately determine suitability of the product and designs to his or her specific requirements and assumes responsibility for its use. PHYSICAL PROPERTIES 3L73 FILL, VOID OR CAVITY MATERIALS FOR USE IN JOINT SYSTEMS & THROUGH- PENETRATION FIRESTOP SYSTEMS. SEE UL FIRE RESISTANCE DIRECTORY PROPERTIES Color Odor Density Solids Content by Weight 83% Coverage Tack Free Time, hours 2-4 FAST TACK FIRESTOP SPRAY Neutral / Off White Negligible Skin Over Time, minutes 45 Viscosity, Centipoises 15,000 ± lbs/gal ( g/l) 12.8 sq. 1/8, (0.31 m mm) PROPERTIES FAST TACK FIRESTOP SPRAY Tensile Strength, psi Elongation % 200 Peel Strength, lbs/inch 5 Hardness, Shore A Permeability 0.04 Volatile Organic Content (VOC), g/l 132 g/l Flame Spread* 0 Smoke Development* 20 In Service Temp -35 F (-37 C) F (177 C) Storage Temp 0 F (18 C) - 80 F (27 C) Shelf Life** 1 Yr *ASTM E 84 14% Surface Coverage (modified test for sealants and caulks) **From date of manufacture. SPECIFICATIONS The fire protective joint coating shall be a single component, moisture curing elastomeric silicone/urethane hybrid coating. The coating as applied shall be insoluble and immiscible in water, and cure to form a flexible, moisture resistant film. The coating shall adhere to all common construction surfaces and be of a high static viscosity, capable of being applied by brush, roller, or airless sprayer. The approved coating shall be SpecSeal Fast Tack Firestop Spray. SPECIFIED DIVISIONS DIV Through-Penetration Firestopping DIV Special Construction Fire Suppression & Supervisory Systems DIV Mechanical Insulation Fire Protection DIV Basic Electrical Materials & Methods Technical Service STI Product Data Sheet Series FT Fast Tack Firestop Spray FOD /2013 1

14 INSTALLATION INSTRUCTIONS GENERAL: Areas to be protected must be clean and free of oil, loose dirt, rust or scale. Unsound surfaces may need to be power washed with clean water diluted bleach solution, and then power rinsed to remove dirt. Recommended storage temperatures range between 0 F (-18 C) and 80 F (27 C). Recommended application temperatures range between 40 F (4 C) and 95 F (35 C). Applying coating in lower temperatures than specified will lengthen skin over, tack-free and ultimate cure time. For best results, relative humidity should be above 20%. Lower humidity will slow the cure rate significantly. Consult appropriate manufacturer s system drawing for design requirements. Forming or packing materials may be required as an integral part of various system designs. For best performance, coating may be applied by airless spray to a 1/8 (3.2 mm) wet thickness. Do not attempt to add water or solvent to SpecSeal Fast Tack Firestop Spray. Clean up of equipment containing uncured material may be accomplished by flushing with mineral spirits. SpecSeal Fast Tack Firestop Spray should not be left in pumping equipment and/or hoses for prolonged periods of time. Hoses shall be TEFLON lined, connections shall be sealed with TEFLON and pump seals shall be TEFLON. SpecSeal Fast Tack Firestop Spray cures by reacting with moisture vapor to form cured material. Equipment without TEFLON lining and seals will transmit sufficient moisture vapor to gradually cure material on hose walls and unsealed connections which may directly result in increased operating pressures and material flow restriction. As an option, SpecSeal Fast Tack Firestop Spray may also be used as a self-leveling sealant and poured into the linear opening to the required thickness as specified in the individual UL System design. TEFLON is a registered trademark of Dupont. MAINTENANCE INSPECTION: Installations should be periodically inspected for subsequent damage. Following safety precautions listed below and pertinent installation guidelines remove coating in damaged areas and reapply fresh coating material to original coating thickness. TECHNICAL SERVICE Specified Technologies, Inc. provides toll free technical support to assist in product selection and installation information. UL Classified Systems are available at the Technical Library at PRECAUTIONARY INFORMATION Consult Material Safety Data Sheet for additional information on the safe handling and disposal of this material. Avoid contact with eyes. The use of an OSHA or NIOSH approved mask for dust and mist environment is recommended. Use only in well ventilated areas. To clean areas of skin contact, wipe off uncured material with a dry cloth or paper towel prior to washing. Waterless hand cleaners are particularly effective when sealant is uncured. AVAILABILITY SpecSeal Fast Tack Firestop Spray is available from authorized distributors. Consult factory for the names and locations of the nearest sales representatives or distributors. APPLICATION EQUIPMENT NOTICE: Spray application of SpecSeal FastTack Spray requires airless spray equipment meeting the following specifications. Working Pressure: Minimum 2500 psi Delivery: Minimum 1.0 US gpm (2.1 l/min) recommended. Spray Tip Orifice: to in. recommended Wetted Parts: All seals, hoses and contact surfaces should be Teflon. A minimum 3/8-in. diameter fluid line is required. Consult pump manufacturer for long hose runs or lifts to higher elevations. A reversible spray tip is recommended. A 6-in. fan pattern is suggested to minimize overspray. The following airless spray equipment has demonstrated suitability for application of this product. STI makes no warranties concerning the suitability or use of this equipment and has no affiliation of any kind with its manufacturer. The following equipment is manufactured by Titan Tool, Inc. Franklin Lakes, NJ: Item PowrTwin Model 5500 Sprayer Item Name & Description Electric or gas powered airless sprayer ORDERING INFORMATION CAT. NO. FT305 Additional SpecSeal Products... DESCRIPTION 5 gallon pail 1,155 cu. in. (19 liters) Elastomeric Joint Sealants Economical products for sealing construction joints. Choose caulk or spray applied products tested to UL2079. City of NY MEA M Important Notice: All statements, technical information, and recommendations contained herein are based upon testing believed to be reliable, but the accuracy and completeness thereof is not guaranteed. WARRANTY: Specified Technologies Inc. manufactures its goods in a manner to be free of defects. Should any defect occur in its goods (within one year), Specified Technologies Inc., upon prompt notification, will at its option, exchange or repair the goods or refund the purchase price. Limitations and Exclusions: THIS WARRANTY IS IN LIEU OF ALL OTHER REPRESENTATIONS EXPRESSED OR IMPLIED (INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR USE) AND UNDER NO CIRCUMSTANCES SHALL SPECIFIED TECHNOLOGIES INC. BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL PROPERTY DAMAGE OR LOSSES. PRIOR TO USE, THE USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR ITS INTENDED USE, AND THE USER ASSUMES ALL RISKS AND LIABILITY FOR SUBSEQUENT USE. No statement or recommendation not contained herein shall have any force or effect unless in an agreement signed by officers of seller and manufacturer. MADE IN THE USA COPYRIGHT 2013 SPECIFIED TECHNOLOGIES INC. 2 Technical Service STI Product Data Sheet Series FT Fast Tack Firestop Spray FOD /2013

15 Material Safety Data Sheet 28-AUGUST-2013 SpecSeal AS200 ELASTOMERIC SPRAY CHEMICAL PRODUCT/COMPANY IDENTIFICATION Material Identification PRODUCT NAME...SpecSeal AS200 SPRAY CHEMICAL FAMILY...Mixture Company Identification MANUFACTURER/DISTRIBUTOR Specified Technologies Inc. 210 Evans Way Somerville, NJ PHONE NUMBERS Product Information : Emergency : HAZARDS IDENTIFICATION ***********EMERGENCY OVERVIEW************ * Possible skin and eye irritant. Paste. * ******************************************************* Potential Health Effects: EYE: Contact may cause irritation. SKIN: Contact may cause irritation. INGESTION: Relatively non-toxic. INHALATION: Irritation of the nose, throat, and lungs may result from over-exposure to vapors or mist. CHRONIC (CANCER) INFORMATION: Not classified as carcinogenic. LONG TERM TOXIC EFFECTS: None known. COMPOSITION/INFORMATION ON INGREDIENTS Proprietary mixture containing in part: INGREDIENT NAME CAS NUMBER ACRYLIC COPOLYMER Non Hazardous CALCIUM CARBONATE TITANIUM DIOXIDE ALUMINA TRIHYDRATE Page 1 of 3 MSDS - SpecSeal SERIES AS200 Elastomeric Spray FOD-5043

16 FIRST AID MEASURES First Aid INHALATION: Remove to fresh air. SKIN CONTACT: Wash thoroughly. EYE CONTACT: Irrigate eyes with running water for at least 15 minutes. Get medical attention if irritation develops. INGESTION: None applicable. FIRE FIGHTING MEASURES Not a fire hazard. EXTINGUISHING MEDIA.... Dry Chemical; Carbon Dioxide; Foam; Water spray for large fires. SPECIAL FIRE FIGHTING PROCEDURES: As for surrounding fire. ACCIDENTAL RELEASE MEASURES Safeguards (Personnel) NOTE: Review FIRE FIGHTING MEASURES and HANDLING (PERSONNEL) sections before proceeding with clean-up. Use appropriate PERSONAL PROTECTIVE EQUIPMENT during clean-up. HANDLING AND STORAGE Store under ambient conditions. No special handling required. EXPOSURE CONTROLS/PERSONAL PROTECTION EYE PROTECTION REQUIREMENTS:...Safety glasses/goggles. SKIN PROTECTION REQUIREMENTS:...Gloves. RESPIRATOR REQUIREMENTS:...None. VENTILATION REQUIREMENTS:...If needed, use local exhaust ventilation to keep airborne concentrations below the TLV. Exposure Guidelines Exposure Limits PEL(OSHA) : Particulates (Not Otherwise Classified) 15 mg/m3, 8 Hr. TWA, total dust 5 mg/m3, 8 Hr. TWA, respirable dust TLV(ACGIH): None Established PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL FORM...Paste SPECIFIC GRAVITY PERCENT VOLATILES...23+/-2 EVAPORATION RATE...>1 BOILING POINT deg. C SOLUBILITY IN WATER...Infinitely dilutable CARB VOC (Calculated) Wt.% SCAQMD VOC (US EPA Method 24)...10 Grams/Liter STABILITY AND REACTIVITY STABILITY:...This is a stable material. CONDITIONS TO AVOID...Storage >55 deg. C HAZARDOUS POLYMERIZATION:...Will not occur. INCOMPATIBILITIES:......None special TOXICOLOGICAL INFORMATION Mixture not tested but based on components: May be irritating to skin and eyes and may produce symptoms of nausea in poorly ventilated areas. None of the components are listed as carcinogens. Page 2 of 3 MSDS - SpecSeal SERIES AS200 Elastomeric Spray FOD-5043

17 ECOLOGICAL INFORMATION No data. DISPOSAL CONSIDERATIONS Waste Disposal: Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations. TRANSPORTATION INFORMATION DOT not regulated. REGULATORY INFORMATION U.S. Federal Regulations TSCA Inventory Status : Reported/Included. Section 313 Supplier Notifications. This product contains no toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 and of 40 CFR 372 OTHER INFORMATION NPCA-HMIS Rating Health : 1 Flammability : 0 Reactivity : 0 Personal Protection rating to be supplied by user depending on use conditions. STATE RIGHT-TO-KNOW LAWS No substances on the state hazardous substances list, for the states indicated below, are used in the manufacture of products on this Material Safety Data Sheet, with the exceptions indicated. While we do not specifically analyze these products, or the raw materials used in their manufacture, for substances on various state hazardous substances lists, to the best of our knowledge the products on this Material Safety Data Sheet contain no such substances except for those specifically listed below: SUBSTANCES ON THE NEW JERSEY WORKPLACE HAZARDOUS SUBSTANCE LIST PRESENT AT A CONCENTRATION OF 1% OR MORE (0.1% FOR SUBSTANCES IDENTIFIED AS CARCINOGENS, MUTAGENS OR TERATOGENS): Alumina, Titanium Dioxide. WARNING: SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER: None Known.. WARNING: SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM: None known. This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. Such information is to the best of our knowledge and belief accurate and reliable as of the data compiled. However, no representation, warranty, or guarantee is made as to its accuracy, reliability or completeness. It is the user s responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use. We do not accept liability for any loss or damage that may occur form the use of this information. Responsibility for MSDS : Specified Technologies Inc. 210 Evans Way Somerville, NJ Page 3 of 3 MSDS - SpecSeal SERIES AS200 Elastomeric Spray FOD-5043

18 Material Safety Data Sheet 22-JAN-2009 SpecSeal Fast Tack AWG CHEMICAL PRODUCT/COMPANY IDENTIFICATION Material Identification PRODUCT NAME...SpecSeal Fast Tack AWG CHEMICAL FAMILY...Mixture Company Identification MANUFACTURER/DISTRIBUTOR Specified Technologies, Inc. 200 Evans Way Somerville, NJ PHONE NUMBERS Product Information : Emergency : COMPOSITION/INFORMATION ON INGREDIENTS INGREDIENT NAME CAS NUMBER PERCENT D4 & HMDZ TREATED SILICON DIOXIDE METHYLTRIMETHOXYSILANE LIMESTONE >37.1 STEARIC ACID <1.95 QUARTZ <0.39 DISTILLATES, PETROLEUM HYDROTREATED LIGHT POLYDIMETHYLSILOXANE SILANOL/STPD HAZARDS IDENTIFICATION Potential Health Effects: **************************EMERGENCY OVERVIEW****************************** * Combustible. Irritating to skin, eyes and respiratory tract irritant. May be * * harmful if swallowed, inhaled or absorbed through skin. Off-white liquid. * *************************************************************************************** EYE: Contact with vapor or liquid causes irritation. SKIN: Contact may cause irritation and defatting. May be absorbed through skin to cause toxic effects. INGESTION: May be harmful if swallowed. May cause headache, dizziness, nausea, vomiting and gastrointestinal irritation and central nervous depression. INHALATION: Irritation of the nose, throat, and lungs may result from over-exposure to vapors or mist from uncured material. CHRONIC (CANCER) INFORMATION: Crystalline silica is a carcinogenic. LONG TERM TOXIC EFFECTS: None known. Page 1 of 4 MSDS - SpecSeal Fast Track AWG FOD-5081