Architecture - Engineering - Planning

Transcription

1 Architecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRAWING REVIEW REVIEWED FURNISH AS CORRECTED REVISE AND RESUBMIT REJECTED SUBMIT SPECIFIED ITEM This review is only for general conformance with (1) the design concept and (2) the information given in the construction documents. Corrections or comments made on a shop drawing during this review do not relieve the contractor from compliance with the requirements of the plans and specifications. Approval of a specific item does not include approval of an assembly of which the item is a component. The contractor remains responsible for: dimensions to be confirmed and correlated at the job site; information that pertains solely to the fabrication process or to the means, methods, techniques, sequences and procedures of construction; coordination of the Work with that of all other trades; and performing all Work in a safe and satisfactory manner. By: Jeff Cramer Date: Jun 12, 2012 Comments: Spec section specifies Resilient Base and accessories. The submitted shop drawing specifies VCT tile. File Name:

2 Westlake City Schools Submittal Cover Sheet (To be filled out and submitted with each submittal) Westlake LBMS Capstone Construction School Contractor: Various Date Specification Section: Sub Specification Section: Product Data Contractor s Submittal # Revision # Submittal Type 6 Frank Novak Lead Time After Approval (wks) Manufacturer/Supplier: All- VCT Info Intended Area of Use, Drawing # and Detail Reference: Contractor Stamp ACCEPTANCE IS FOR GENERAL COMPLIANCE WITH THE CONTRACT DOCUMENTS ONLY. THE CONTRACTOR IS RESPONSIBLE FOR CONFIRMING AND CORRELATING ALL QUANITITES AND DIMENSIONS; COORDINATING ITS WORK WITH THAT OF ALL OTHER TRADES; AND PERFORMING ITS WORK IN A SAFE AND SATISFACTORY MANNER. APPROVED Digitally signed by Tim Steffen DN: cn=tim Steffen, o=capstone Construction Company, ou, =tim@capstone-construction.net, c=us Date: :33:44-04'00' Architect Stamp CM Stamp TURNER/RESOURCE Reviewed for general acceptance only. This review does not relieve the Contractor of the responsibility for making the work conform to the requirements of the contract. The Contractor is responsible for all dimensions, correct fabrication and accurate fit with the work of other trades. SUBJECT TO ARCHITECT S APPROVAL Kyle Richardson 6/7/ Signed: Date: CM Submittal #: Engineer Stamp

3

4 Product Specifications ESSENTIALS & DESIGNER ESSENTIALS PHYSICAL CONSTRUCTION Construction Through-Pattern Vinyl Composition Tile Size 12" x 12" (305 mm x 305 mm) Overall Thickness.125 inches (3.2 mm) Package/Count 45 per carton Coverage Per Carton 5 sq. yds. Average Weight 65 lbs. per carton (29.5 kg per carton) 1.4 lbs. per tile (0.6 kg per tile) Boxes Per Pallet 30 ENVIRONMENTAL FloorScore Indoor Air Quality CHPS Indoor Air Quality Manufacture Location SCS Certified Passed and Listed Salem, NJ USA TESTING ASTM Specification (F-1066) Class 2 HUD / FHA Requirements Exceeds Flooring Radiant Panel Test (ASTM-E-648) >.45 watts / cm², Passes Class 1 N.B.S. Smoke Chamber Test (ASTM-E-662) <450 Passes Static Coefficient of Friction Meets ADA Guidelines Static Load Limit 125 psi (8.79 kg/cm²) WARRANTIES Vinyl Composition Tile (VCT) Warranty INSTALLATION Installation Adhesive Limited 5 Year Commercial Warranty Mannington M-Guard V-11 / Full Spread* Color and pattern extend through the thickness of the tile. VCT is not recommended for use in hospital operating suites, commercial kitchens, or in areas that require static dissipation. Darker colors of vinyl composition tile may be subject to scratch whitening, requiring more frequent maintenance. Wood subfloors directly on concrete or sleepers, either on or below grade, are unsatisfactory for VCT installation. VCT is not recommended in commercial areas where the surface temperature over radiant heated substrate exceeds 90 F. *Verify substrate (concrete) is dry per ASTM F lbs. maximum MVTR or ASTM F % maximum relative humidity. Dirt, wetness, and improper maintenance may cause significant variation in actual performance. Specifications are based on averages from normal manufacturing tolerances. Such variations do not affect product performance. This product is intended solely for use as an indoor floor covering and is not recommended or sold for any other purpose. Use entryway systems outside each entrance to prevent dirt, sand, grit, and other substances from being tracked onto floor.

5 maintenance maintenance section VI vinyl composition tile, premium visual tile and slip retardant tile vinyl composition tile: essentials / designer essentials premium visual tile: brushwork / colorpoint / solidpoint / inspirations slip retardant tile: safewalks general information Proper and regular maintenance is necessary to protect and prolong the life of the floor. A good maintenance routine involves the following: Frequent sweeping, mopping, or vacuuming to control loose soil and grit Prompt removal of stains and spills Polishing to protect the floor surface and add gloss. Always use a quality name brand product and follow manufacturer recommendations to ensure the best results. Restrict traffic when cleaning, waxing, or stripping due to the possibility of slipping. Use protective runways when moving heavy objects, even if equipped with wheels, to avoid causing adhesive displacement, marring, or gouging of the tile. maintenance for a newly installed floor Do not wash or scrub the floor for at least 4 or 5 days after installation to allow the floor tiles to bond to the underlayment / subfloor. Keep heavy furniture and equipment off the floor for at least 48 hours to allow the adhesive to set. Sweep or vacuum thoroughly and remove any residual adhesive with a clean white cloth dampened with mineral spirits. Apply a minimum of two coats of a high quality cross-linked acrylic floor polish to temporarily protect the floor until regular maintenance procedures can begin. preparation for commercial use 1. Scrub the floor using a good quality non-alkaline floor cleaner and a floor machine of low RPM equipped with a green or blue scrubbing pad. 2. Heavily soiled or scratched floors may be stripped, following the same procedure as for scrubbing, but using a floor stripping detergent. 3. Thoroughly rinse the floor, being careful to avoid flooding the floor, and allow the floor to dry completely. 4. Apply 3 5 coats* of a high-quality, cross-linked acrylic floor polish, allowing sufficient drying time (at least 30 minutes) between applications. *NOTE: Maintenance conditions vary. Contact the polish manufacturer to determine the specific recommendations for polishing based upon your equipment, schedule, traffic, and desired gloss level. regular maintenance 1. Clean floor frequently with a treated (non-oily) dust mop or clean, soft push broom. 2. Damp mop the floor as required, using a properly diluted, neutral-detergent solution. Light scrubbing with an automatic floor machine may be required in heavily soiled areas. 3. Rinse the floor with clean water and allow to dry completely. 4. After damp mopping or light scrubbing, spray buffing or high speed burnishing may be performed to restore gloss. NOTE: During cleaning, floors become wet and slippery. Caution wet floor signs must be displayed. spray buffing Spray buff only when a solid base coat of at least three coats of polish already exists on the floor. Spray buff using a diluted floor polish (7% 8% solids) or a spray buffing compound. Before the liquid is dry, buff with a floor machine equipped with a white or tan buffing pad or a soft brush at medium RPM. After buffing the liquid dry, a thin, glossy film remains which protects the base coat of polish, reducing the need for stripping. Heavy traffic areas may need extra coats of polish on a more frequent basis. high speed burnishing CAUTION: Operators of ultra high-speed burnishing machines should be well trained. Careless or improper use of these machines can result in severe and extensive damage to the floor. Ensure that the floor is free of all loose dirt and debris. High-speed burnishing utilizes a machine of RPM capacity. It is a dry buffing procedure performed on a floor already coated with at least four coats of polish specifically formulated for burnishing. This base coat should be periodically rebuilt by recoating to compensate for loss of finish from this operation. The machine should be operated in a straight line, with a push-pull method, rather than a sweeping motion. When the floor appearance no longer responds to high-speed burnishing, thoroughly clean the floor and apply gloss restorer, spray buff or recoat the original finish (see page ). Burnishing is not recommended for installations exhibiting telegraphing of subfloor irregularities or debris trapped under the floor (inadequate floor preparation). stripping Use of high quality maintenance products and regular adherence to a quality maintenance program will greatly reduce the need for stripping. Strip floors only when necessary. Follow the manufacturer s label recommendations for proper dilution, use, clean-up, and disposal of stripper. CAUTION: High solvent content strippers (no-rinse / no-scrub) must NOT be used on tile floors installed less than two years old. Apply stripper liberally with a clean mop and allow it to penetrate into the floor finish for several minutes (without allowing it to dry). Scrub the floor with a single disc floor machine equipped with a red, green, or blue pad at low RPM. Remove all stripping solution with a squeegee and wet vacuum or a damp mop. Immediately rinse floor with clear water, remove rinse water with a squeegee and wet vacuum or damp mop. Allow the floor to dry completely, then reapply polish (see pages ). 142 technical information

6 warranty Vinyl Composition Tile LIMITED 5 YEAR COMMERCIAL WARRANTY Mannington Commercial vinyl composition tile products Essentials,Designer Essentials, and Progessions are backed by a Limited 5-Year Commercial Warranty for manufacturing defects as described below. The vinyl composition tile products Essentials, Designer Essentials, and Progessions that you purchase are guaranteed to be free from manufacturing defects. If a defect occurs in your floor, upon verification of the defect, Mannington will authorize repair or replacement of the affected area without charge, with flooring of equal value and/or quality. If your floor was installed by a professional flooring installer/contractor, Mannington will also pay reasonable professional labor costs to install your replacement floor if the defect is reported within the first year of the original purchase, and 50% if the defect is reported within the second year of the original purchase. Labor costs will not be reimbursed if the defect is reported within the third, fourth, or fifth year of the original purchase pursuant to Mannington Commercial installation instructions. EXCEPTIONS AND LIMITATIONS 1. Limited commercial warranty applies from the date of purchase and only to the original owner of the floor. 2. Wear from chairs or other furniture without proper floor protectors will void the warranty. 3. Indentations, scratches or surface damage caused by improper maintenance, misuse, negligence, spike heeled shoes, pebbles, sand, or other abrasives are not covered by this warranty. 4. Dissatisfaction due to improper installation or installation contrary to Mannington recommendations will void the warranty. Mannington Commercial Installation Guidelines are available on our website manningtoncommercial.com. 5. Labor on material installed with obvious defects is not covered by this warranty. 6. Labor costs on repair or replacement of material which was not originally professionally installed are not covered by this warranty. 7. Any discoloration or bond failure on Mannington Commercial products resulting from improper adhesive selection or application is not covered by this warranty. 8. Problems due to moisture, mildew, alkaline substances, or hydrostatic pressure in the sub-floor are not covered by this warranty. 9. Using non-recommended floor care products may damage the floor and void the warranty. 10. Purchase of seconds, remnants, mill trials or other irregular (non-first quality) flooring material, or material not part of, or available in the regular Mannington Commercial product line are not warranted. Note: If the Mannington Commercial floor fails to perform as stated in the applicable Limited Warranty, Mannington Commercial will, at its option: (i) repair without charge the affected flooring to conform to the warranty; or (ii) replace the affected flooring without charge, with flooring of equal value and/ or quality. Mannington Commercial will also pay for reasonable labor costs per the conditions stated above. Mannington Commercial will not pay for the removal or replacement of cabinets, appliances, or other fixtures. Replacement floors are warranted only for the remaining time of the original warranty and are not warranted to match samples or marketing materials (ie. photographs, website, etc) or match in color, dye lot, and gloss with your existing floor. THESE ARE YOUR EXCLUSIVE REMEDIES UNDER THE LIMITED WARRANTIES SET FORTH ABOVE. UNDER THE TERMS OF THESE LIMITED WARRANTIES, MANNINGTON COMMERCIAL WILL NOT BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES OF ANY KIND, NO MATTER WHAT THE CAUSE. THERE ARE NO IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, EXTENDING BEYOND THE TERMS OF THESE LIMITED WARRANTIES. EXCEPT AS SET FORTH HEREIN, THERE ARE NOT EXPRESS WARRANTIES MADE BY MANNINGTON COMMERCIAL. Choices that Work manningtoncommercial.com