WarmTouch for STANDARD and LARGE AREAS. WarmTouch Mats & Cables. WarmTouch Mats & Cables. USA 2014 All graphics & pictures are for illustration only

Transcription

1 . WarmTouch for STANDARD and LARGE AREAS USA 2014 Copyright All rights reserved. & all related companies. The materials in this page, may not be

2 Resistance Wires (twin) FEP Coating Reinforced insulation Polyamide Jacketing Super strong aramid Shielded Grownding WarmTouch Classic Mats VOLT 120v 120V WIDTH )FT( LENGTH )FT( SQFT Technical Data Mat Output 120v Mat Output 240v Cable Output 15Wsqft 12Wsqft 3W/Linear Ft 120V Voltage 120V AC / 240V/60HZ Cable Outer jacketing PA Jacketing 042V 042V 042V Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Tested in accordance with UL and CSA. to be installed in accordance to NEC. Wire Thickness Protection Means Supply Lead Connection Base Material Cable Color Wire Spacing Cold Lead Length 1/8 GFCI In accordance to NEC One side connection (Twin Conductor) White textile mesh Green 2 1/4 13ft Copyright All rights reserved. & all related companies. The materials in this page, may not be 2

3 Installation WET INSTALLATION 1 2 Plan the layout 3 4 Attach one of Domoteck s testing instrument Thermostat to regulate floor temperature Two adjacent conduits 1. Protecting Tube ( non heating leads) 2. Sensor pipe Place insulation boards and coat the surface with a primer 5 6 Spread first layer of thin set morter Junction Box Tiles or other stone covering Thin set mortar or self leveling mortar Warming element Sub-Floor Insulation Building structure Using a roller press down the mat Spread second layer of tile glue 7 OR 8 Using various fixing means fix the mat to the insulation boards Pour self-leveling morter 9 10 Place floor covering e.g. tiles Set the thermostat Copyright All rights reserved. & all related companies. The materials in this page, may not be 3

4 Resistance Wires (twin) FEP Coating Reinforced insulation Polyamide Jacketing SEE ACCESSORIES 11, 13, 15 watt sqft Super strong aramid Shielded Grownding Warm Touch Classic Cables WarmTouch Classic Cables are perfectly suited for new construction and remodeling projects. The warming element can be integrated into almost any floor cross-section with a minimal change in floor elevation. WarmTouch Classic Cables are perfectly suited for wet installation under tile, stone and marble. WarmTouch Classic Cable is a twin conductor cable and has a single connection point that simplifies the installation process. WarmTouch Classic Cable gives the homeowner the flexibility to decide the W/sqft and allows him to reach places which cannot easily be reached by a mat. VOLT 120V 042v Cable Length Output ( 2.75W/ linear Ft) Technical Data Mat Output Voltage Cable Outer Insulation 2.75W/Linear Ft 120V AC / 60HZ 240V AC /60HZ PA Jacketing Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Tested in accordance with UL and CSA. to be installed in accordance to NEC. Wire Thickness Protection Means Supply Lead Connection Cable Color Supply Lead Length 1/8 GFCI In accordance to NEC One side connection (Twin Conductor) Green 13Ft Copyright All rights reserved. & all related companies. The materials in this page, may not be 4

5 Installation 1 2 WET INSTALLATION Plan the layout Attach one of Domoteck s testing instruments 3 4 Thermostat to regulate floor temperature Two adjacent conduits 1. Protecting Tube ( non heating leads) 2. Sensor pipe Place insulation boards and coat the surface with a primer If using the insulation, fix the anchoring means down onto the boards Junction Box Tiles or other stone covering Thin set mortar or self leveling mortar 5 If not, fix the anchoring means to the sub floor Warming element Sensor Sub-Floor Insulation Building structure Fix the cable into the anchoring means OR 6 7 domoteck s warranty policy Domoteck s products are guaranteed by a 10-year Limited Product Warranty, and are designed to safely operate according to the life-span of the application in which they are installed. Spread a layer of thin set mortar 8 9 Pour self-leveling mortar Place floor covering e.g. tiles Set the thermostat Copyright All rights reserved. & all related companies. The materials in this page, may not be 5

6 Resistance Wires Reinforced insulation Braided grounding (to activate GFCI) Polyamide Jacketing Super strong aramid WarmTouch Basic Mats WarmTouch Basic Mats are ideal for installation under tile, stone and marble especially in large areas. They are also versatile to warm other approved floor coverings such as floating, laminates, linoleum and wall-to-wall carpeting. WarmTouch Basic Mats are simple to install ( Are delivered as semi fixed size just lay the mat and fix it to subfloor, see illustration), ultra safe and economically affordable. They are perfectly suited for installation in new construction and remodeling projects. WarmTouch Basic Mats feature an absorbent textile mesh that simplifies the mat installation and perfectly integrating into the floor cross-section. WarmTouch Basic Mats should be embedded in latex-modified thin-set mortar for tile and stone warming applications. VOLT WIDTH (FT) LENGTH (FT) SQFT W/UNIT Technical Data Mat Output 12Wsqft 240V Cable Output 3 W/ft 240V Voltage 240V AC / 60HZ Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Tested in accordance with UL and CSA. to be installed in accordance to NEC. Cable jacketing Wire Thickness Protection Means Supply Lead Connection Base Material Cable Color Wire Spacing Supply Lead Length PA 12 1/9 GFCI In accordance to NEC Two sided connection White Textile Orange 3 2x10ft each side For further details refer to product installation manual Copyright All rights reserved. & all related companies. The materials in this page, may not be 6

7 Mat Flexibility WarmTouch Basic Mats come factory prepared as a Fixed Size to warm basic rectangular shaped areas. Just unroll the mat, open it and adhere it to the sub- floor OR The mat can be easily re-shaped by cutting the mesh ( DO NOT CUT THE WIRE) and adjust it to cover the required floor space. Follow the simple illustrations outlined in the product installation guide to learn more about how to achieve the custom coverage you need. Copyright All rights reserved. & all related companies. The materials in this page, may not be 7

8 Resistance Wires Super strong aramid Reinforced insulation Braided grounding (to activate GFCI) Polyamide Jacketing SEE ACCESSORIES 11, 13, 15 watt sqft Warm Touch Basic Cable WarmTouch Basic Cables offer the best solution in installation flexibility; installers can modify the space between the wires according to the required heat load. WarmTouch Basic Cables are ideal for installation under tile, stone, and marble, especially in large areas. They are also versatile enough to warm other approved floor coverings such as floating wood, laminates, linoleum and wall-to-wall carpeting. WarmTouch Basic Cables should be fixed to the subfloor with Domoteck s custom distance Keepers or with adhesive tape. * Contact Domoteck customer service for more information about the distance keepers WarmTouch Classic Cable gives the homeowner the flexibility to decide the W/sqft and allows him to reach places which cannot easily be reached by a mat. VOLTS CABLE LENGTH SQFT COVERED 15W/Sqft SQFT COVERED 13W/Sqft SQFT COVERED 11W/Sqft Technical Data Cable Output 2.75 W/ft 042V 102V Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Tested in accordance with UL and CSA. to be installed in accordance to NEC. Voltage Cable jacketing Wire Thickness Protection Means Supply Lead Connection Cable Color Supply Lead Length 120V AC/ 60HZ 240V AC / 60HZ PA 12 3/32 GFCI In accordance to NEC Two sided connection IVC Orange 2x10ft Copyright All rights reserved. & all related companies. The materials in this page, may not be 8

9 WET INSTALLATION 1 2 Plan the layout Attach one of Domoteck s testing instruments 3 4 Thermostat to regulate floor temperature Junction Box Two adjacent conduits 1. Protecting Tube ( non heating leads) 2. Sensor pipe Tiles or other stone covering Thin set mortar or self leveling mortar Place insulation boards and coat the surface with a primer 5 If using the insulation, fix the anchoring means down onto the boards If not, fix the anchoring means to the sub floor. Warming element Sub-Floor Insulation Building structure Fix the cable into the anchoring means OR 7 Spread a layer of 1/2 thin set mortar Pour self-leveling concrete 8 9 Place floor covering e.g. tiles Set the thermostat Copyright All rights reserved. & all related companies. The materials in this page, may not be 9

10 Wood Warming Mats VOLTS 120 V LENGTH (Ft) WIDTH (Ft) 1.5 SQFT W/unit Technical Data Mat Output Cable Output 10W/Sqft 1.7W/Linear Ft Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Tested in accordance with UL and CSA. to be installed in accordance to NEC. Voltage Cable jacketing Wire Thickness Protection Means Supply Lead Connection Base Material Cable Color Wire Spacing Supply Lead Length 120V AC / 60HZ PA 12 5/64 GFCI In accordance to NEC Two side connection White Textile + Aluminum foil Silver 2 2x13ft each side Copyright All rights reserved. & all related companies. The materials in this page, may not be 11

11 1 2 DRY INSTALLATION Plan the layout Attach one of Domoteck s testing instruments = Thermostat 2 = Tube for Floor Sensor 3 = Junction Box 4 = Sensor 5 = Wooden Floor/Parquet 6 = Warming Element 7 = CCPE (closed cell polyethylene) 8 = Sub floor 9 = Insulation 10 = Construction Roll out the CCPE 5 6 Roll the AL-mat over the CCPE Frame the Al-mat with a blind net Place floor covering e.g. parquet 7 For full installation details please refer to product installation manual Set the thermostat Copyright All rights reserved. & all related companies. The materials in this page, may not be 11

12 Resistance wire Reinforced insulation Adhesive tape Heat distribution strip Super strong aramid FEP Coating Shielded Braiding DOMOTHERM CLASSIC MAT TWIN Domotherm Mats can be installed under: Tiles, marble flooring (wet installation) Laminated wooden floors (dry installation) Other flooring materials that are applicable for floor heating or warming. As "wet installation" or "dry installation". The Domotherm mat is manufactured with a screened heating element which is integrated within a wide thin heating distribution strip. This construction of the heating element offers great advantages compared to thin sheet flexible heating elements with integrated cable and these are: Short heat up time Temperatures can be easily regulated Domotherm is environmentally friendly, high-comfort and safe. Its flat structure (0.04 ) minimizes floor elevation and can be easily applied to existing floors-ideal for renovation. The Domotherm mat is designed and manufactured in accordance with the highest safety standards. Technical Data Mat Output 12W/Sqft 15W/Sqft Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Cable Output Voltage Ribbon width Wire Thickness Protection Means Supply Lead Connection Base Material Wire Spacing Supply Lead Length 3W/Linear Ft -3.75W/Linear Ft 240 V/ 60HZ 1 1/13 GFCI In accordance with NEC One side twin conductor Red Fiberglass + Al 3 1/7 2x 10Ft Copyright All rights reserved. & all related companies. The materials in this page, may not be 12

13 WET Installation 1 2 WET INSTALLATION Plan the layout Attach one of Domoteck s testing instruments Thermostat 3 4 Conduit Junction box Sensor Flooring Tiles or Natural Stone FWM embedded In thin set morter Construction Place insulation boards and coat the surface with a primer 5 6 Spread first layer of thin set morter Insulation of the building Sub-floor OPTIONAL To improve efficiency DOMOTECK recommends using insulation boards in your installation Press down the mat 7 OR 8 Spread second layer of thin set morter Thermostat Conduit Fix the mat with various fixing means Pour self-leveling morter Junction box Flooring Tiles or Natural Stone 9 10 Sensor FWM installed on insulation boards Construction Insulation of the building Sub-floor Place floor covering e.g. tiles Set the thermostat For full installation details please refer to product installation manual Copyright All rights reserved. & all related companies. The materials in this page, may not be 13

14 DRY Installation 1 2 DRY INSTALLATION Thermostat Plan the layout Attach one of Domoteck s testing instruments 3 4 Conduit Junction box Flooring Sensor FWM Installed on CCPE 4mm Construction Insulation of the building 5 Roll out the CCPE Roll the mat over the CCPE 6 Sub-floor Frame the mat with a blind net Place floor covering e.g. parquet 7 8 E.g. carpet Set the thermostat For full installation details please refer to product installation manual Copyright All rights reserved. & all related companies. The materials in this page, may not be 14

15 Living Heat Under floor mat The Living Heat unlike any other- is an ultra thin heating mat (25 micron ribbon total height with mat :2.5mm) based on the unique and patented Amorphous Metal Ribbon heating technology. Specially designed to be a total project solution down to the smallest room or conservatory, its ultra thin structure and low surface temperature provides you with an easy to install product, Suitable for new constructions as well as renovations. An energy efficient heating system. The Living Heat is available in fixed or semi-flexible sizes, allowing you to obtain the best coverage. The Living Heat must be connected to the main electric box through an GFCI (30mAMps) that not only protects the heating element but also increases personal safety. Perfect heat distribution due to its flat structure and good surface coverage. Living Heat mats can be installed under: Tiles and marble flooring (wet installation) Laminated wooden floors (dry installation) VOLT WIDTH (inch) LENGTH (FT) SQFT W/UNIT Voltage Technical Data 120V AC 120V Watt Sqft Outer insulation 12w/SQFT LLDPE 102V Thickness of mat/wire 0.10 Ribbon width Exact measurements: Width,length and output to be found in DomoTeck SLP ( Suggested List Price). Tested in accordance with UL and CSA. to be installed in accordance to NEC. Protection class/means Connection Net color Supply lead length GFCI in accordance with NEC One side connection Orange 2x5m(16 feet) Copyright All rights reserved. & all related companies. The materials in this page, may not be 15

16 WET INSTALLATION 1 WET Installation 2 Plan the layout Attach one of Domoteck s testing instruments Thermostat 3 4 Conduit Junction box Sensor Flooring Tiles or Natural FWM embedded In thin set morter Construction Place insulation boards and coat the surface with a primer 5 6 Spread first layer of Thin set morter Insulation of the building Sub-floor OPTIONAL To improve efficiency DOMOTECK recommends using Insulation boards in your installation Press down the mat 7 OR 8 Spread second layer of Thin set morter Thermostat Conduit Fix the mat with various fixing means Pour self-leveling morter Junction box Flooring Tiles or Natural Stone 9 10 Sensor FWM installed on insulation boards Construction Insulation of the building Sub-floor Place floor covering e.g. tiles Set the thermostat For full installation details please refer to product installation manual Copyright All rights reserved. & all related companies. The materials in this page, may not be 16

17 DRY Installation 1 2 DRY INSTALLATION 3 Plan the layout Attach one of Domoteck s testing instruments 4 Thermostat Roll out the CCPE Roll the mat over the CCPE Conduit 5 6 Junction box Flooring Sensor FWM Installed on CCPE 4mm Construction Insulation of the building Frame the mat with a blind net Place floor covering e.g. parquet Sub-floor 7 8 e.g. Carpet Set the thermostat For full installation details please refer to product installation manual Copyright All rights reserved. & all related companies. The materials in this page, may not be 17

18 Control units CU 111-SF DESCRIPTION & FEATURES: CU111-SF is a 5-day programmable thermostat designed for floor warming. The thermostat has an integrated Ground Fault Circuit Interrupter (GFCI, Class B). The thermostat and the GFCI is a dual model suitable for 120/240V 50/60Hz supply. TECHNICAL DATA: CHARACTERISTICS Range Accuracy Programmable Remote Floor Sensor Adjustable Switching Differential Thermostat Tested Manual Override Memory Backup Max Switching Current Supply Option Energy Unit Dimensions (mm) FLOOR MODE 41 F-104 F (05-40ºC) 32 F (0.5C ) Yes Yes 8ft (2.5m) Yes IPX 0 Yes Yes 16A 120V AC/240V AC NO 115x90x16 Color - White Large LCD display + Display temperatures Recalibrates. Built-in GFCI Two relays for protection against writing error 5 day programming with 4 separate Time & Temperature periods per day Permanent user setting and program setting retention during power loss. Optional temperature display of Celsius or Fahrenheit scale. Optional types of control for different heating applications: room control, floor control or room control with floor temperature limitation. For more information info@domoteck.us Control untis Copyright All rights reserved. & all related companies. The materials in this page, may not be 18

19 Control units CU 512 S/F TECHNICAL DATA: CHARACTERISTICS Range Accuracy Programmable Remote Floor Sensor Adjustable Switching Differential Thermostat Tested Manual Override Max Switching Current Supply Option Energy Unit Dimensions (mm) CU 512-S/F FLOOR MODE 41 F-104 F (05-40ºC) 32 F Yes Yes 9ft (3m) Yes IP 21 Yes 16A 120V AC/240V AC Yes 86x86x16 DESCRIPTION & FEATURES: Color: Off-White Energy unit is connected to line voltage Heating element is connected to energy unit Only a shallow junction box is required Decorative Design - Midsize Display - Backlit Display ºC/ ºF option Weekly Program Setting Individual 5-day Setting 0-day (weekday) + 2-day (Saturday/Sunday) 0-day (weekday) + 1-day/1-day (Saturday/Sunday) Programmable (6 events per 24 hours) Time & Temperature Control Panel 5.5V SELV (higher safety in bathrooms, children s rooms etc.) Connected to Domoteck Energy Unit Control Panel and Energy Unit are separate units and can be installed as such Includes instruction manual CU 512 S/F 120V Energy Unit CU 512 S/F Connected to Heating Element through GFCI for safety 02/51 AMPS 5mA GFCI Receptable SENSOR CU 512S/F Heating Element 240V Energy Unit Multifunction Energy Unit (120V & 240V) For more information info@domoteck.us Control untis Copyright All rights reserved. & all related companies. The materials in this page, may not be 19

20 Accessories for Mats & Cables Product Name Article No. units Application Tube for Sensor 1/2 5ft unit Installation of Thermostat Sensor 90 0 C Angle AC unit Fixing Sensor Tube in place Installation Kit AC 718 Including pipe 14/2+1 +angle+corrugated 8 + electrical box set Installation of control unit CCPE Insulation mats AC x units 1.5m2/4mm sqft Installation under the Aluminium Mat Blind Net AC x sqft To be framed around the aluminum mat to level off the floor height Aluminium adhesive tape 164ft ft For fixing cable to the sub floor Fixing Strip Aluminium Length 30Ft unit x 1.5 ft 20 unit x 1.5 ft 20 unit x 1.5 ft Spacing loops - 3 Spacing loops - 2 1/2 Spacing loops 2 13/64 NEW Ecc 3 ( electrical connection chain) unit ECC-connection Ecc 5 (electrical connection chain) unit ECC-connection Copyright All rights reserved. & all related companies. The materials in this page, may not be 21

21 DOMOTECK Floor Warming Systems Inc. is the North American distributor and the proud subsidiary of Domoteck Ltd. DOMOTECK Ltd. is a world leading manufacturer of advanced radiant heating systems based on the principle of energy-efficient, low temperature heating. DOMOTECK also offers a suite of comfort appliances for the home and office aimed at meeting every type of heating requirement. DOMOTECK s mission is to provide its customers with superior products supported by prompt and professional service. 90% of DOMOTECK S annual production is exported throughout the world, from New Zealand in the south to Norway in the north. DOMOTECK Ltd. and the entire DOMOTECK family are warming hundreds of thousands of homes throughout the world. Domoteck Floor Warming Systems Inc. Address: Tel: 885 S Roselle Road, Schaumburg, IL 60193, USA (Toll-Free) (Local) Fax: Website: service@domoteck.com