VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF CIVIL ENGINEERING. Third years

Transcription

1 VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF CIVIL ENGINEERING Third years CE6601 DESIGN OF REINFORCED CONCRETE & BRICK MASONRY STRUCTURES UNIT I RETAINING WALLS Design of Cantilever and Counterfort Retaining walls Part A 1. A cantilever retaining wall supports an inclined backfill. Sketch the distribution of active earth pressure on the stem. (Nov/Dec-2013) 2. Name the two important stability aspects of a retaining wall. (Nov/Dec-2013) 2. a What are the stability checks in case of retaining wall? (Nov/Dec-2011) (a) The wall should be stable against sliding (b) The wall should be stable against Overturning (c) The wall should be stable against bearing capacity failure. 3. What is the structural action between cantilever and counter fort type retaining wall? (May/June 2013) Cantilever Retaining Wall Counter Fort Type Retaining Wall 1. This is a reinforced concrete wall which When the height of the cantilever retaining utilises cantilever action to retain the wall is more than about 7m, it is economical to backfill. provide vertical bracing system known as 2. This type is suitable for retaining backfill counter forts. to moderate heights (4m-7m). In cross In this case, both base slab and face of wall section most cantilevered walls look like span horizontally between the counter forts. L s or inverted T s. 3. The cantilevered base is reinforced and is designed to prevent uplifting at the heel of the base, making the wall strong and stable. 3. What is the function of weep hole in retaining wall construction? (May/June 2013) Weep holes at the base of retaining walls are intended to bleed off excess moisture that collects behind the wall. In the old days the drain might simply be a burlap bag filled with pea gravel.

2 4. What is gravity retaining wall? (Nov/Dec-2012) A retaining wall that relies solely on it s own weight to stand up is called a gravity wall. Allan Block combines the basic engineering principles of setback, leverage and total unit mass with simple mechanics to make highly stable gravity walls. 5. What are the stability requirements for retaining wall? (Nov/Dec-2012) 5. a. What are the Requirements to be satisfied for the stability of retaining wall? (May/June-2012) Following conditions must be satisfied for stability of wall. a. It should not overturn b. It should not slide c. It should not subside i.e Max. pressure at the toe should not exceed the safe bearing capacity of the soil under working condition 6. What are the types of retaining wall? (Nov/Dec-2011) a. Gravity retaining wall b. Cantilever retaining wall Counter fort retaining wall Soldier Pile retaining wall 7. Why counterforts are provided in a Counter fort retaining wall? (Nov/Dec- 2008) Sometimes cantilevered walls are butressed on the front, or include a counterfort on the back, to improve their strength resisting high loads. 8. What are the structural action of stem, heel and toe of cantilever retaining wall? Illustrate with sketches. (Nov/Dec-2008) a. Gravity retaining wall b. Cantilever retaining wall c. Counter fort retaining wall Soldier Pile retaining wall 9. Why counterforts are provided in a Counter fort retaining wall? (Nov/Dec- 2008) Sometimes cantilevered walls are butressed on the front, or include a counterfort on the back, to improve their strength resisting high loads. 10. What are the structural action of stem, heel and toe of cantilever retaining wall? Illustrate with sketches. (Nov/Dec-2008) Forces acting on a retaining wall are 1. Lateral earth pressure due to the back fill 2. Vertical forces including weight of soil, stem, heel, toe, and soil fill above the toe. 3. The soil pressure developed to resist the earth pressure and other vertical forces acting on the heel and toe. 11. What is a Retaining wall? Retaining walls are generally used to retain earth or such materials to maintain unequal levels on its two faces.

3 The soil on the back face is at a higher level and is called back fill. Retaining walls are extensively used in the construction of basements below ground level, wing walls of bridge and to retain slopes in hilly terrain roads. 12. What are the disadvantages of gravity retaining walls? Gravity walls of stone masonry were generally used in the earlier days to the height of the earth fill. The advent of reinforced concrete has resulted in thinner retaining walls. 13. What is a cantilever retaining wall? The most common and widely used retaining wall is of cantilever type. Vertical stem resisting earth pressure one side and the slab bends like a cantilever. The thickness of the vertical slab is large at the bottom and decreases towards the top in proportion to the varying soil pressure. 14. What is a counter fort retaining wall? Counter fort retaining walls are used for large heights exceeding 5 mts of earth fill. In counterfort retaining wall the vertical stem is designed as a continuous slab spanning between the counterforts. Counter forts are designed as cantilever beams from the base slab. 15. Define Active Earth pressure. If the soil exerts a push against the wall by virtue of its tendency to slip laterally and seek its natural slope (angle of repose) thus making the wall to move slightly away from the back filled soil mass. This kind of pressure is known as AEP. 16. Define Passive earth pressure. The pressure or resistance which soil develops in response to movement of the structure towards it is called the Passive Earth Pressure. 17. What is meant by surcharge? The position of the backfill lying above the horizontal plane at the elevation of the top of a wall is called the surcharge. 18. What is meant by submerged backfill? The sand fill behind the retaining wall saturated with water is called submerged backfill. 19. What is meant by back anchoring of retaining wall? When the height of retaining wall is much more, it becomes uneconomical to provide counterforts. In order to reduce the section of stem etc. in the high retaining walls, the stem may be anchored at its back. The anchor practically takes all the earth pressure and B.M and S.F. in the stem are greatly reduced. 20. When is the design of shear key necessary? When the wall is unsafe in sliding, shear key will have to be provided 16marks 1. Design the main bars of 16 mm diameter and the distribution and the distribution bars of 8 mm diameter required at the bottom section of the stem of a cantilever retaining wall to retain a

4 horizontal backfill level with its top for the following data. Height of the stem = 4.5 Thickness of stem at top and bottom: 200 mm and 450 mm respectively. Density of soil is 18 kn/m 3 and angle of repose is Materials used in the construction are M25 grade of concrete and Fe 415 steel reinforcement. (Nov/Dec-2013) 2. Design the main bars of 12 mm diameter and distributors of 8 mm diameter required at the bottom section of the stem of a counter fort retaining wall to suit the following data. Nature of backfill: Horizontal Height of stem = 6.5 m Thickness of stem at top and bottom: 250mm and 450 mm respectively. Density of soil is 18 kn/m 3 and angle of repose is Centre to centre spacing of counter forts = 3 m Materials used are M25 grade of concrete and Fe 415 steel reinforcement. (Nov/Dec- 2013) 3. Design a cantilever retaining wall to retain earth embankment 4.5m above ground level. The density of earth is 18kN/m 3 and its angle of response is 30 o.the Embankment is horizontal at its top the safe bearing capacity may be taken as 200kN/m 2 and the coefficient of friction between soils and concrete is 0.5. use M20 concrete and fe 415 grade steel reinforcement. (May/June- 2013). 4. Design a cantilever retaining wall with surcharge to retain earth embankment 4.0m abovr ground level. The density of earth is 18KN/m 3 and its angle of response is 30 o. the sand fill slopes at the rate of 1 vertical to 2 horizontal at its top. The safe bearing capacity may be taken as 175 KN/m 2 and the coefficient of friction between soils and concrete is 0.5. Use M20 concrete and Fe 415 grade steel reinforcement. (May/June- 2013). 5. Explain the steps to be followed in proportioning and design of retaining walls. 6. Design a reinforced concrete cantilever retaining wall to retain earth level with the top of the wall to a height of 5.5 m above ground level. The density of soil at site is 17 KN/Cu.mts with a safe bearing capacity of 120 KN/sq.mts. Assume the angle of shearing resistance of the soil as 35degrees. Further assume a coefficient of friction between soil and concrete as Adopt M20grade concrete and Fe415 HYSD bars. 7. A Cantilever type retaining wall is to be designed to support a bank of earth 4m above the ground level on the toe side of the wall. The backfill surface is inclined at an angle of 15 degrees with the horizontal. Assume that good soil is available for foundations at a depth of 1.25m below the ground level with a safe bearing capacity of 160KN/m and an angle of shearing resistance of 30degrees.Assume co-efficient of friction between soil and concrete as 0.5,Adopt M-20 grade concrete and Fe-415 HYSD reinforcement. Assume the unit weight of soil as 16kN/m3. 8. Design a counter fort type retaining wall to support an earth fill of 7.5m above ground level. The foundation depth may be taken as 1.5m below the ground level. The safe bearing capacity of soil at site is 150KN/m2..Unit weight of soil may be taken as 16KN/m3 and an angle of shearing resistance of 30 degrees. Assume the value of coefficient of friction as.55.adopt M-20 grade concrete and Fe-415 HYSD bars. Sketch the details of reinforcements in the retaining wall. UNIT II WATER TANKS Design of rectangular and circular water tanks both below and above ground level Design of circular slab.

5 1. What are the forces acting on the domes? (May/June-2013) a) The thrust (T), which pushes down with an angle on the walls b) A concentric thrust (CT), which acts in every ring and compresses it 2. What are the conditions to be considered for the cylindrical tank situated underground? (May/June-2013) a) Ground tanks should always be designed as either hemi-spherical (half ball shape) or cylindrical because those shapes equalize the pressure of water and soil whether the tanks are full or empty. b) Water tanks should never be designed using square and rectangular shapes because they will collapse due to the uneven pressure of water and soil whether the tanks are full or empty 3. What theory is used to design? (Nov/Dec-2012) (a) The members under direct tension (b) The members under bending tension c) Principle of elastic theory d) Theory of bending 4. Name the types of movement joints. (Nov/Dec-2012) a. Contraction b. Expansion c. Sliding 5. How the water tanks are are classified? (May/June-2012) 5. (a). How will you classify the water tank? (Nov/Dec-2011) Classification Based on shape Rectangular, circular, square, intze type tanks. spherical tanks, conical bottom tanks, and suspended bottom tanks. Classification Based on Applications Potable water storage, Water storage for fire protection, Septic applications and Rainwater harvesting Classification Based on type i) Tanks resting on ground ii) Underground tanks iii) Elevated water tank 6. What are conditions under which the walls of underground water tanks designed? (May/June-2012)(Nov/Dec-2011) (a) Tank full with water, with no earthfill outside. (b) Tank empty, with full earth pressure due to saturated earthfill. 7. Why cover dome for a circular water tank is economical than a flat cover slab? (Nov/Dec-2011), (Nov/Dec-2008) Dome cover slabs are the lightest slab in construction. a) They can be used when the internal pressure is higher; do not have problems with mounting of an internal floating roof. b) Supplementary foundations are not necessary for dome roofs. c) Snow and rain water not accumulating on the cover dome. In other words always when it is possible the dome roofs are economical than flat cover slab.

6 8. Why bracing are provided in the staging of water tank? (Nov/Dec-2008) a) To decrease the Bending Moment at bottom of column b) To avoid the buckling of column c) Increasing the stiffness of column 9. What are the effects of joints reaction due to the continuity in a water tank design? (Nov/Dec-2007) In the membrane analysis, every member is assumed to undergo deformation independent of others. Since the joints are continuous, these deformations are to be compatible. It is to be noted that continuity effects alters the hoop stresses near joints and also imposes meridional moments, while the meridional stresses are not affected and remain the same as in membrane state. The changes due to continuity are only of local nature and their effects die out soon. In the interior portion of members, only membrane stresses exist. 10. Why the uplift pressure is critical on the floor of underground tanks? (Nov/Dec-2007) The floor of the tank is designed for the uplift pressure, for the empty tank condition. This will require reinforcement in the reverse direction than that required for downward loading. The absence of above reinforcement will cause the collapse as shown in figure. 11. Mention the grade of concrete which is used in the construction of water tank. Richer concrete mix of grades M20 to M30 are commonly used in the construction of water tanks. High quality concrete, in addition to providing water tightness, also has higher resistance to tensile stresses developed in the tank walls. 12. Mention the three factors that must be considered while designing a RCC tank. i. Strength ii. Water tightness iii. Overall stability 13. What are the types of reinforced concrete water tanks? i. Tanks resting on ground ii. Underground tanks iii. Elevated water tanks. 14. Mention the reinforcement details that should be provided in a water tanks. Minimum area of steel is 0.3 percent of gross area of section upto 100mm thick, reduced to 0.2 percent in section up to 450mm thick. For sections above 225mm thick, provide two layers of reinforcement.

7 The percentage of reinforcement in base or floor slab resisting directly on ground must be not less than 0.15% of the concrete section. The minimum cover to all reinforcement should be not less than 25mm or the diameter of the bar whichever is greater. 15. Define the term: Dome: A Dome is defined as a thin shell generated by the revolution of a regular curve about one of its axes. 16. Define the following terms: i. Latitude: The circle of each ring in a dome is called Latitude. ii. Meridian circle: The circle drawn through two diametrically opposite points on a horizontal diameter and the crown is known as meridian circle. 17. Define the following terms: i. Radial: The joint between successive horizontal rings is called radial. ii. Meridian thrust: The reaction between the rings is tangential to the curved surface giving rise to compression along the medians. The compressive stress is called meridional thrust or meridional compression. 18. Mention the thickness and steel requirement of dome. A minimum thickness of 7.5cm is provided to protect steel. Minimum steel requirement is 0.15% for mild steel bars and 0.12% for HYSD bars of the sectional area in each direction meridionally as well as along the latitudes. 19. What are the three types of joints in water tank? i. Movement joints :- a. Contraction b. Expansion c. Sliding ii. Construction joints iv. Temporary open joints 20. What is the foundation specification for small capacity tanks? For small capacity tanks individual footings for columns can be provided. Infact, the type of footing will depend upon the nature of soil and type of staging. In case of low lying areas of low safe bearing capacity with high ground water table, pile footings are provided. In any case of foundation slab, lean mix of 1:4:8, 150mm thick may be provided as leveling course. 21. What are the methods available for the analysis of circular tank? i. IS code method ii. Reissner s method iii. Carpenter s method iv. Approximate method 22. What are movement joints in water tanks? These joints require the incorporation of special materials in order to maintain water-tightness while accommodating relative movement between the sides of the joints. All movement joints are essentially flexible joints.

8 23. What is contraction joint in water tanks? A contraction joint is a typical movement joint which accommodates the contraction of the concrete. 24. What is meant by expansion joint in water tanks? It is a movement joint with complete discontinuity in both reinforcement and concrete, and is intended to accommodate either expansion or contraction of the structure. 25. What are underground water tanks? Underground water tanks are used for storage of water received from water supply mains operating at low pressures, or received from other source. 26. What are conditions under which the walls of underground water tanks designed? (a) Tank full with water, with no earthfill outside. (b) Tank empty, with full earth pressure due to saturated earthfill. 27. What are the four components of design of underground water tanks? Design of long walls Design of short walls Design of roof slab Design of base slab 28 What are two methods of analysis of rectangular tanks? (i) Approximate analysis (ii) Exact analysis based on elastic theory 29 Where are domes used? (i) Roof of circular areas (ii) Circular tanks (iii) Hangers (iv) Exhibition halls, auditoriums and planetariums and (v) Bottoms of tanks, bins and bunkers 16 marks 1. Design the top dome, top ring beam and cylindrical side wall of an elevated circular water tank supported over eight columns for the following data. Internal diameter = 12 m Height of tank = 8 m Central rise of dome = 12 m The base of the tank above ground level is 10 m Materials used in the construction are M20 grade of concrete and Fe 415 steel reinforcement. (Nov/Dec-2013) 2. Explain the steps involved in the wind load analysis of a rectangular elevated water tank supported on four identical columns with their lower ends and braced at two intermediate levels. (Nov/Dec-2013) 3. A reinforced dome of 6m base diameter with a rise of 1.25m is to be designed for a water tank. The uniformly distributed live load including finishes on dome may be taken as 2KN/M 2. Adopting M20 concrete and Fe415 grade steel, design the dome and ring beam. (May/June- 2013).

9 4. Design a RC tank of internal dimension 10mx3mx3m. the tank is to be provided under ground. The soil surrounding the tank is likely to get wet. Angle of repose of soil in dry state is 30 degree and in wet state is 6 degree. Soil weight 20KN/m 3. Adopt M20 concrete and Fe415 grade steel. (May/June-2013). 5. An open rectangular tank 4m x 6m x 3m deep rests on firm ground. Design the tank. Use M20mix. 6. Design a circular tank with flexible base for capacity of liters. The depth of water is to be 4m, including a free board of 200mm.Use M20 concrete. 7. Design an underground water tank 4m x 10m x 3m deep. The sub soil consist of sand having angle of repose of 30 degree and saturated unit weight of 17KN/m3.The water table is likely to rise up to ground level. Use M20 concrete and HYSD bars. Take unit weight of water as9.81kn/m3 8. Design the side wall of a circular tank of capacity1.5 lakh litres of water. The depth of the tank is limited to 2.5m. The joint between the wall and base as flexible. The base slab rest on the ground. Use M 20 grade concrete. 9. Design a spherical dome over a circular beam for the following data a. Inside diameter of room = 12m Rise of dome = 4m b. Live load due to wind, snow,etc = 1.5 KN/m 2 The dome has an opening of 1.6m diameter at its crown. A lantern is provided at its top, which causes a dead load of 22KN acting along the circumference of the opening. Use M20 concrete and Fe415 steel. 10. Design an underground water tank of size 3m x 8m x 3m for the following data. Type of soil: submerged sandy soil with density = 16 KN/m 3 and angle of internal friction Φ=30. The water table can rise upto ground level. Design the side walls of the tank. (May/June-2012) UNIT III SELECTED TOPICS Design of staircases (ordinary and doglegged) Design of flat slabs Principles of design of mat foundation, box culvert and road bridges PART - A 1. Distinguish between one-way shear and punching shear in flat slabs? (Nov/Dec-2013) One-way shear The one-way shear is analogous to that generates in a beam due to flexure. This is checked in a two-way slab for each spanning direction separately.

10 Two-way shear or Punching Shear The two -way shear is specific to two-way slabs. If the capacity is inadequate, the slab may fail due to punching around a column. The punching occurs along a conical frustum, whose base is geometrically similar and concentric to the column cross-section. The following figure illustrates the punching shear failure. 2. What are the load cases for which a box-culvert should be designed to remain safe? (Nov/Dec-2013) Concentrated Loads, Uniform Distributed Loads, Weight of Side Walls, Water Pressure Inside Culvert, Earth Pressure on Vertical Side Walls, Uniform Lateral Load on Side Walls 3. What is flat slab and give the different types? (May/June-2013) A flat slab is a typical type of construction in which a reinforced slab is built monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams. Different types of flat slabs a) Slabs without drops and column heads b) Slabs without drops b) Slab with drops and column with column head 4. What is the thickness of flat slab with and without drops? (May/June-2013) From the consideration of deflection control IS specifies minimum thickness in terms of span to effective depth ratio. For this purpose larger span is to be considered. If drop as specified in is provided, then the maximum value of ratio of larger span to thickness shall be = 40, if mild steel is used = 32, if Fe 415 or Fe 500 steel is used If drops are not provided or size of drops do not satisfy the specification 1.2.1, then the ratio shall not exceed 0.9 times the value specified above i.e., = 40 x 0.9 = 36, if mild steel is used. = 32 x 0.9 = 28.8, if HYSD bars are used It is also specified that in no case, the thickness of flat slab shall be less than 125 mm. 5. List the classification of staircase. (Nov/Dec-2012) 5. a. What are the types of Staircase? (May/June-2012) (Nov/Dec-2010) They are broadly classified as Straight stair, Quarter turn stair, Half turn stair, Dog legged stair Open newer stair with quarter space landing, Geometrical stairs such as circular stair, spiral stair, etc. 6. What do mean by column and middle strip in flat slab? (Nov/Dec-2012) The panel shown in Figure has size L1 x L2. A panel may be divided into column strips and middle strips. Column Strip means a design strip having a width of 0.25L1 or 0.25L2, whichever is less. The

11 remaining middle portion which is bound by the column strips is called middle strip. 7. What are the limitations of direct design method of flat slabs? (May/June-2012) (Nov/Dec-2010) This method has the limitation that it can be used only if the following conditions are fulfilled: (a) There shall be minimum of three continuous spans in each direction. (b) The panels shall be rectangular and the ratio of the longer span to the shorter span within a panel shall not be greater than 2. (c) The successive span length in each direction shall not differ by more than one-third of longer span. (d) The design live load shall not exceed three times the design dead load. (e) The end span must be shorter but not greater than the interior span. 8. When a mat founded resorted to a structure? (Nov/Dec-2008) The mat foundation is an ground type of foundation used to provide load bearing capacity in expansive, rocky or hydro collapsible soils. 9. What are the advantages of box culvert over the slab culvert? (Nov/Dec-2008) Box for cross drainage works across high embankments has many advantages compared to a slab culvert. i) It is easy to add length in the event of widening of the road ii) Box is structurally very strong, rigid and safe. iii) Box does not need any elaborate foundation and can easily be placed over soft foundation by increasing base slab projection to retain base pressure within safe bearing capacity of ground soil. iv) Easy to construct, practically no maintenance, can have multi-cell to match discharge within smaller height of embankment. 10. Draw a neat sketch of flat slab with drop panel and column head? (Nov/Dec-2007)

12 11. What is a stair case? A staircase consists of a number of steps arranged in a series, with landings at appropriate locations, for the purposes of giving access to different floors of a building. 12. Define tread: Tread: The horizontal portion of a step was the foot rests is referred to, as tread.250 to 300 mm is the typical dimensions of a tread. 13. Define Riser Riser is the vertical distance between the adjacent treads or the vertical projection of the step with value of 150 to 190 mm depending upon the type of building. 14. Define Going: Going is the horizontal projection of an inclined flight of steps between the first and last riser. 15. What is a flight? A flight is the length of the staircase situated between two landings. The number of steps in a flight may vary between 3 to What is the minimum rise and tread in residential buildings? In residential buildings, the rise may vary between 150mm to 180mm tread between200mm to 250mm. 17. What is the minimum rise and tread in public buildings? In public buildings, the rise may vary between 120mm to 150mm tread between200mm to 300mm. 18. Mention the places where the following staircase can be used _ Single flight staircase is used in cellars or attics where the height between floors is small and the frequency of its use is less. _ Quarter turn staircase flight generally runs adjoining the walls and provides uninterrupted space at the centre of the room. Generally used in domestic houses where floor heights are limited to 3m. _ Dog legged staircase is generally adopted in economical utilization of available space. _ Open well staircases are provided in public buildings where large spaces are available. In congested locations, where space availability is small, Spiral stairs are provided. 19. Define flat slab. A flat slab is a typical type of construction in which a reinforced slab is built monolithically with the supporting columns and is reinforced in two or more directions, without any provision of

13 beams. 20. What are all the components of flat slab? Drop of flat slab, Capital or column head, Panel 21. Define drop of flat slab. Drop is that part of the slab around the column, which is of greater thickness than the rest of the slab. 22. Define capital or column head. Sometimes the diameter of a supporting column is increased below the slab. This part of column with increased diameter is called column head. 23. Define panel of flat slab. It is the area enclosed between the centre lines connecting adjacent columns in two direction sand the outline of the column heads. 24. What are the methods of analysis of flat slab? (i) The direct design method (ii) The equivalent frame method 25. What are all the assumptions made in direct design method? (i) There shall be minimum of three continuous spans in each direction. (ii) The panel shall be rectangular, and the ratio of the longer span to the shorter span within a panel shall not be greater than Explain about box culvert shortly. A box culvert is continuous rigid frame of rectangular section in which the abutment and the top and bottom slabs are cast monolithic. A box culvert is used where a small drain crosses a high embankment of a road or a railway or a canal- especially when bearing capacity of soil is low. 27. Give the names of various types of bridges. Solid slab bridge or deck slab bridge. Deck girder bridge or T-beam bridge. Balanced cantilever bridge, Rigid frame culvert. Arch bridge. Bowstring girder bridge. Continuous girder or arch bridge. 16 marks 1. Design one of the flights of stairs of a school building spanning between landing beams to suit the following data. (Nov/Dec-2013) Type of staircase: waist slab type. Number of steps in flight = 12 Tread = 300 mm and rise = 160 mm Width of landing beams = 400 mm Materials used are M20 grade of concrete and Fe 415 steel reinforcement. 2. Design a reinforced concrete wall of 3 m height, 100 mm thick and 4 m long between the cross walls. The factored load to be carried by the wall is 600kN/m. Materials used are M20 grade of concrete and Fe 415 steel reinforcement bars. (Nov/Dec-2013) 3. Design an interior panel of a flat slab for a live load of 5KM/m 2. The panel size is 6mx6m. The diameter of the column is 500mm. drops may be provided. Use M20 concrete and Fe415 steel. Sketch the details of reinforcement. (May/June-2013)

14 4. Design a straight stair for a residential building consisting of individual steps projecting 950 mm from the face of the wall. The rise and tread of stairs are 180 mm and 260 mm respectively. The live load may be taken as 3KN/m 3. Use M20 concrete and Fe415 HYSD bars. (Nov/Dec- 2012) 5. An open rectangular tank 4m x 6m x 3m deep rests on firm ground. Design the tank. Use M20mix. 6. Design a circular tank with flexible base for capacity of liters. The depth of water is to be 4m, including a free board of 200mm.Use M20 concrete. 7. Design an underground water tank 4m x 10m x 3m deep. The sub soil consist of sand having angle of repose of 30 degree and saturated unit weight of 17KN/m3.The water table is likely to rise up to ground level. Use M20 concrete and HYSD bars. Take unit weight of water as9.81kn/m3 8. Design the side wall of a circular tank of capacity1.5 lakh litres of water. The depth of the tank is limited to 2.5m. The joint between the wall and base as flexible. The base slab rest on the ground. 9. Design a spherical dome over a circular beam for the following data a. Inside diameter of room = 12m Rise of dome = 4m b. Live load due to wind, snow, etc = 1.5 KN/m2 The dome has an opening of 1.6m diameter at its crown. A lantern is provided at its top, which causes a dead load of 22KN acting along the circumference of the opening. Use M20 concrete and Fe415 steel. UNIT IV YIELD LINE THEORY Assumptions Characteristics of yield line Determination of collapse load / plastic moment Application of virtual work method square, rectangular, circular and triangular slabs Design problems PART A 1. Sketch the yield line pattern in the rectangular slab fixed on all the edges and subjected to a uniformly distributed load. (Nov/Dec-2013) 1. a. Draw any two yield line pattern of rectangular slab. (Nov/Dec-2012) 2. State the principle used in the virtual work method of yield line analysis. (Nov/Dec-2013)

15 If a deformable structure in equilibrium under the action of a system of external forces is subjected to a virtual deformation compatible with its condition of support, the work done by these forces on the displacements associated with the virtual deformation is equal to the work done by the internal stresses on the strains associated with this deformation. 3. Define yield line theory. (May/June-2013) The failure of reinforced concrete slabs of different shapes such as square, rectangular, circular with different types of edge conditions is preceded by a characteristic pattern of cracks, which are generally referred to as yield lines. 4. Give any four assumptions in yield line theory. (May/June-2013) 4. a. List the assumption made in yield line analysis of slabs. (May/June-2013) (Nov/Dec- 2011) 1. The steel reinforcement is fully yielded along the yield lines at collapse. Rotation following yield is at constant moment. 2. The slab deforms plastically at collapse and is separated into segments by the yield lines. The individual segments of the slab behave elastically. 3. The elastic deformations are neglected and plastic deformations are only considered. The entire deformations, therefore, take place only along the yield lines. The individual segments of the slab remain plane even in the collapse condition. 4. The bending and twisting moments are uniformly distributed along the yield lines. The maximum values of the moments depend on the capacities of the section based on the amount of reinforcement provided in the section. 5. The yield lines are straight lines as they are the lines of intersection between two planes. 5. Define isotropically and orthotropically reinforced slabs. (Nov/Dec-2012) If the reinforcement in the two directions is not the same, it is said to be orthotropically reinforced slab. The ultimate moment of resistance in an isotropically reinforced slab, in any direction, is the same 6. What are the characteristic of yield lines? (May-June-2012) (Nov/Dec-2007) i.yield lines end at the supporting edges of the slab ii.yield lines are straight iii.a yield line or yield line produced passes through the intersection of the axes of rotation of adjacent slab elements. iv.axes of rotation generally lie along lines of supports and pass over any columns. 7. Sketch an yield line pattern for a continuous slab over a its edge support. (Nov/Dec- 2011).

16 8. What are the two methods of determining the ultimate load capacity of reinforced concrete slabs? (i) Virtual work method (ii) Equilibrium method 9. What is the direction of yield line in one way slab? In one way slab, the direction of yield line is perpendicular to the direction of steel. 10. What is the direction of yield line in two way slab? In two way slab, the direction of yield line is not perpendicular to the direction of steel. 11. What is the concept of yield line method? In the yield line method, the computation of ultimate load is based on the pattern of yield lines that are developed in the slabs under conditions approaching collapse. 12. Who innovated yield line theory? This method was innovated by Ingerslav (1923) and was greatly extended and advanced by Johanssen 13.Draw the yield line moment for Reinforced circular slab, S.S all round and UDL? (Dec 2010) 14. Write down the formula for moment by equilibrium method for square slab Reinforced to a UDL? 15. Write down the formula for moment by equilibrium method UDL? 16. Draw the yield line moment for Reinforced by equilibrium method for rectangular slab Reinforced to a UDL?

17 17. What are the followed for the End conditions of Yield Line Theory of Slab? 18.How to calculate the moments in Yield Line Theory of Slab? When the yield lines form at right angles to the direction of the reinforcement. The yield or ultimate moments is computed by considering the slab section as under reinforced. According to IS: , the yield or ultimate moment is expressed as

18 19.Draw the Typical Yield Line Pattern in Reinforced Concrete Slab? (Dec2009) 20.What is moment for Square Slab fixed on all the edges and subjected to UDL? 16marks 1. Using virtual work method, obtain the expression for ultimate moment per unit length of the yield line in the case of an isotropically reinforced square slab fixed on all edges and subjected to a uniformly distributed load. (Nov/Dec-2013) 2. Design a rectangular slab of 6m x 4m simply supported at the edges carrying a service live load of 4 kn/m 2. Assume the co-efficient of orthotrophy as 0.7. Materials used are M20 grade of concrete and Fe 415 steel reinforcement bars. (Nov/Dec-2013) 3. Design a rectangular slab of size 4mx6m which is simply supported along the edges and to carry a service live load of 4KN/m 2. Assume coefficient of orthotropy as (May/June-2012) 4. Derive the expression relating yield line moment and ultimate load intensity in the following isotropically reinforced slab: i) Square slab simply supported all around ii) Fixed square slab 5. Design a rectangular slab of size 4mx6m continuous on all four sides using yield line analysis. Assume a live load of 3KN/m 2 and floor finish of 13KN/m 2. Use M20 grade of concrete and Fe 415 steel. (May/June-2013) 6. Design circular slab of diameter 4m which is simply supported at the edges. Adopt service live load as 4KN/m 2 and M20 grade of concrete with Fe 415 HYSD bars. Assume load factors according to IS: code. (May/June-2013) 7. A reinforced concrete square slab, 3.5m X 3.5m is simply supported at the ends and is reinforced with 8mm diameter bars spaced at 150mm centres both ways. Determine the safe service live load if the average effective depth of slab is 100 mm and the total thickness of slab, inclusive of flooring, is 160mm. Use M20 concrete and Fe 415 HYSD bars 8. A rectangular slab 4m X 5m is simply supported at the ends. Design the slab to carry super imposed service load of 5 KN/m 2, if the slab is to be isotropically reinforced Use M20 concrete and Fe 415 HYSD bars 9. A triangular slab has equal side lengths of 4.5m is supported on two edges and is isotropically reinforced with 8mm dia. bars of Fe 415 grade, spaced at 125mm centres both ways. Determine

19 (i) Ultimate moment capacity (ii) ultimate collapse load. The total thickness of slab may be assumed as 120mm in M20 grade concrete. UNIT V BRICK MASONRY Introduction, Classification of walls, Lateral supports and stability, effective height of wall and columns, effective length of walls, design loads, load dispersion, permissible stresses, design of axially and eccentrically loaded brick walls PART A 1. What is cross sectional area of Masonry unit? Net cross sectional area of a masonry unit shall be taken as the gross cross sectional area minus the area of cellular space. Gross cross sectional area of cored units shall be determined to the outside of the coring but cross sectional area of groves shall not be deducted from the gross cross sectional area to obtain the net cross sectional area. 2. What is bond in brick masonry? Arrangements of masonry units in successive courses to tie the masonry together both longitudinally and transversely; the arrangement is usually worked out to ensure that no vertical joint of one course is exactly over the one in the next course above or below it, and there is maximum possible amount of lap. 3. How will you calculating effective length, effective height and effective thickness? The height of a wall to be column to be considered slenderness ratio. The length of a wall to be column to be considered slenderness ratio. The thickness of a wall or column to be considered for calculating slenderness ratio. 4. What meant by lateral support? A support which enables a masonry element to resist lateral and/or restrains lateral deflection of a masonry element at the point of support. 5. What is the slenderness ratio for walls? (Nov/Dec-2012) For a wall, Slenderness ration shall be effective height divided by effective thickness or effective length divided by the effective thickness is less. 6. What is the slenderness ratio for walls and columns? For column slenderness ration shall be taken to be the greater of the ratios of effective heights to the respective effective thickness in the two principal directions. Slenderness ratio for a load-bearing column shall not exceed What is slenderness ratio in brick masonry structures? In brick masonry structures, for a wall slenderness ratio shall be the effective height divided by the effective thickness or effective length divided by the effective thickness whichever is less. 8. What is slenderness ratio in brick column masonry structures?

20 For a column slenderness ratio shall be taken to be the greater of the ratios of effective height s to the respective effective thickness in the two principal directions. Slenderness ratio of a load- bearing column shall not exceed What is reinforced brick work? Reinforced brickwork is a typical type of construction in which the compressive strength of bricks is utilized to bear the compressive stress and steel bars are used to bear the tensile stresses in the slab. 10. What is the thickness adopted for reinforced brick slab? The thickness of slab may be kept as 100mm to 200mm. 11. What is effective length of brick wall when the wall is continuous? (May/June-2013) ANS: 0.8L 12. What is the purpose of providing a lateral support in a masonry structure? Masonry structures gain stability from support offered by cross walls, floors and roofs. Lateral support for load-bearing walls limit the slenderness of the structure. Further the lateral support reduces the possibility of bucking of member due to vertical loads and to resist horizontal forces. 13. What is a pilaster in brick masonry wall? Solid walls are thickened at intervals by increasing he c/s. The thickened portions are called as piers or pilasters. They are used for one of the following purpose: to carry concentrated loads from roof. To provide lateral support. 14. Name the various types of masonry walls used in building construction. Masonry walls may be classified as load-bearing walls and non-load bearing walls. Types of load bearing walls are 1.Solid wall 2.Solid wall with piers 3.Cavity wall 4.Faced wall 5.Veneered wall Types of Non-load bearing walls are 1.Panel wall 2.Partition wall 3.Curtain wall 4.Free-standing wall 15. List the types of mortars used for masonry works. Mortars used in masonry works are cement mortar, lime mortar and cement-lime mortar. 16. What is an equivalent eccentricity? In an eccentrically loaded wall, there is an axial load and a bending moment. These two may be combined into single resultant load acting at a distance. 17. List out any two factors which affect the permissible stress of masonry. 1.Type and strength of bricks 2.Strength of mortar 3.Slenderness ratio 4.Eccentricity of loading 5.Shape and size of bricks 6.C/s area of the masonry

21 PART B (16 Marks) 1. In the wall of a room, 5m long, 300 mm thick and 3.5 m high, there are three openings 0.9 m wide and 1.5 m high. The portion of brickwork between the windows is 200 mm wide each. If the load/m length of the wall at the lintel level is 40 kn/m, Determine what minimum mortar strength must be used in the wall. Strength of bricks may be taken as 9 MPa. (Nov/Dec-2013) 2. Determine the allowable axial load on a column 300 mm * 600 mm constructed in first class brickwork in 1:6 cement mortar using modular bricks 200 mm * 100mm* 100mm. The height of the column between the footing and top slab is 5.1 m. The strength of the brick units may be taken as 10 MPa. (Nov/Dec-2013) 3. A masonry wall is subjected to an axial load of 150 KN and bending moment of 30KNm. The height of the wall is 4m. Design the wall. (Nov/Dec-2012) 4. Design a solid square masonry column of height 2000mm to carry an axial load of 150 KN. The column is tied at top and bottom. Include the self weight of the column for the design. (Nov/Dec-2012) 5. Calculate the safe axial load on a brick pier of size 200mmx200mmx3m height construct using first class bricks having a compressive strength of 7.5N/mm 2 and cement mortar 1:3. (May/June-2012) 6. Calculate the safe axial load per metre length of a solid wall 230 mm thick and the height of the wall is 3.5m. The wall is continuous and its length between the cross wall is 6m. M1 mortar and bricks of strength 5N/mm 2 are used. (May/June-2012) 7. Explain the factors to be considered while designing brick masonry with respect to stability and lateral supports on the structure. 8. What are the factors to be considered while determining the effective height of wall and column sand effective length of walls? 9. Explain the design procedure to design axially and eccentrically loaded brick walls.