REFERENCE. guide POLYMERIC SANDS POLYBIND POLYBIND DUST AQUA ROCK GATOR GATOR BASE TILE SYSTEMS GATOR GATOR GRID AND GATOR FABRIC SEALERS CLEANERS

Transcription

1 REFERENCE guide INSTALLATION EDGES GRID AND FABRIC

2 NO HAZE FREE NO BLOWER ONE WATERING INTELLIGENT POLYMERIC SAND G2 Intelligent polymeric sand is made with a state of the art manufacturing process. Specifically calibrated sand is mixed with sophisticated intelligent polymers. This new generation of Intelligent Polymers neutralizes haze and dust. The intelligent polymeric sand application is now dust free and haze free. No blower is needed and the intelligent polymeric sand requires only one watering. G2 Intelligent polymeric sand is the Cleanest, Fastest & Easiest polymeric sand installed in the industry.

3 Alliance Prides Itself on its Quality Products Dear Friend, Since 2003 Alliance Designer Products has been developing quality products, designed and formulated just for you the hardscape professional. Throughout the years, we ve listened to your feedback and focused on making continual improvements. And today, contractors, dealers, and manufacturers all recognize Alliance as The leader in hardscape accessory products. Which is why we can proudly stand behind this simple yet powerful claim: Quality Is Our Strength. We believe that quality must remain a top priority in everything we do. That s why we re giving you our Total Commitment. A commitment to provide superior quality products backed by our World Class sales and technical service, all supported with our best-in-class marketing tools. As a valued partner, we're excited to reveal a brand new product G2: Intelligent Polymeric Sand : The product that will revolutionize the industry: G2 Intelligent polymeric sand is the Cleanest, Fastest & Easiest polymeric sand installed in the industry. No Dust Haze Free No Blower Required One Watering G2 is manufactured by mixing specifically calibrated sand with sophisticated intelligent polymers, which neutralize haze and dust. The end result: a second generation of polymeric sand unlike anything you've ever seen before. The Colors: COMPLETE G2 will be available in all four of our standard vibrant colors: Nevada Tan, Oxford Grey, Ivory White, and Jet Black. SAND G2 will be available in Nevada Tan and Oxford Grey. G2 is a GAME-CHANGER and we can't wait for you to try it out for yourself. Alliance is forward-thinking and eager to help your business keep a competitive edge in today s highly competitive market. Our research and development team is committed to creating a wide range of innovative products that set your business apart and make you (and your projects) perform better. Our marketing team is committed to providing the latest tools and modern education to not only help you on the job, but to improve your entire business. Whether you are choosing a flagship product like our Polybind sand, our cutting-edge Gator Tile System, or any of our wide range of products, you can design and build with the confidence that you are using the best products in the industry. The following pages detail our complete product line. Throughout the years, Alliance has become the most trusted brand in the Hardscape Industry. All of our polymeric sands and dust are backed by our industry-leading 15-year warranty. You can install with confidence using any of polymeric sand products: SAND G2 or COMPLETE G2, NO HAZE FREE NO BLOWER ONE WATERING SAND or COMPLETE with our Haze free formula Gator Tile Sand and We remain focused and determined in our mission. And we will continue to invest in research and development to meet your challenges of the future. It s all part of our Total Commitment. For more information, great ideas, and comprehensive installation videos, please visit our website at Polybind.com. On behalf of our entire Polybind Team supporting you, we sincerely thank you for your continued confidence and allowing us to be your hardscape partner! We wish you all the best in the coming year. George Tutino, President, Owner

4 Table of Contents G2 6 Polybind Sand G2 8 Polybind Complete Sand G2 10 Polybind Sand 12 Polybind Complete Sand 14 Eurostone Bond Sand 16 Gator Tile Sand POLYMERIC STONE 18 Polymeric Stone Dust Bond 20 Gator Aqua Rock 22 Gator Base 26 Gator Tile Systems GRID AND FABRIC 30 Gator Grid GG 20-20, GG 30-30, GG Gator Fabric GF 3.5, GF 4.4, GF 8, GF 20, GF 5 38 Solvent-based Sealers 40 Water-based Eco Sealers 42 Polybind Deluxe Series for Wet Cast and Natural Stones 45 Shampoo 45 Efflorescence Cleaner 45 X-TRA Oil & Grease Remover 46 Rust Remover 46 Rubber, Paint & Tar Remover 46 Efflorescence & Slurry Remover

5 22 26 GRID AND FABRIC X-TRA Performance Polyurethane Adhesive 50 Gator Rock Bond Kit 50 Gator Rock Bond Liquid Binding Agent 52 Gator Stone Bond XP EDGES 54 Edge Rigid and Flex 54 Edge Mini 54 Gator Tile Edge 54 Gator Base Screws 54 Polybind Nails INSTALLATION AND APPLICATION INSTRUCTIONS 56 Polybind Sand G2 58 Polybind Complete G2 60 Polybind Sand 60 Polybind Complete 62 Polybind Dust Bond 64 Gator Tile Systems 66 Gator Base 68 Polybind Cleaners 70 Polybind Sealers 71 Gator Stone Bond XP 71 Gator Rock Bond 72 Polybind Deluxe Series Sealers 74 Polybind Seal Chart To learn more, visit us online at Polybind.com 5 INSTALLATION EDGES

6 GRID AND FABRIC EDGES NO HAZE FREE NO BLOWER One watering INSTALLATION To learn more, visit us online at Polybind.com 6 SEE INSTALLATION INSTRUCTIONS PAGES 56-57

7 Polybind Sand G2 Intelligent Polymeric Sand For Paver Joints Up To 2 For Drainage Applications NEW IDEAL FOR Residential use, Paver joints up to 2 Concrete pavers, natural stone, wetcast products & clay pavers Sloping areas, pool surroundings, patios, walkways, driveways and much more PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet in USA 70 units per pallet in Canada Pallets can be stored outside Waterproof bags HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions AVAILABLE COLORS FEATURES No dust, Haze free, No blower, One watering. Sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) Waterproof bag 15 Year Limited Warranty SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Nevada Tan Oxford Grey 15 YEAR LIMITED WARRANTY Nevada Tan & Oxford Grey Narrow joints sq ft ( sq m) Wide joints sq ft ( sq m) GRID AND FABRIC The Cleanest, Fastest and Easiest installation steps: Spread G2 Intelligent Polymeric Sand Sweep & Vibrate G2 Intelligent Polymeric Sand Sweep off excess G2 Intelligent Polymeric Sand Activate G2 Intelligent Polymeric Sand with water Polybind's brand new G2 Intelligent Polymeric Sand, is a simplified four easy step installation process, making it the cleanest, fastest and easiest in the industry. SEE VIDEO AT.COM To learn more, visit us online at Polybind.com 7 INSTALLATION EDGES

8 GRID AND FABRIC EDGES NO HAZE FREE NO BLOWER One watering INSTALLATION To learn more, visit us online at Polybind.com 8 SEE INSTALLATION INSTRUCTIONS PAGES 58-59

9 Polybind Complete G2 Intelligent Polymeric Sand For Paver Joints Up To 4 Drainage & Non-Drainage Applications (Overlays) NEW IDEAL FOR Residential & commercial use Paver joints up to 4 Drainage and Non-Drainage applications (Overlays) Concrete pavers, natural stone, wetcast products & clay pavers Streetscape, commercial work, steep slope, pool areas, patios, walkways, driveways & parking areas FEATURES No dust, haze free, no blower, one watering. Drainage base systems, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) Non-Drainage base systems (Overlays), sets within 24 hours after water activation at above 32ºF (0ºC) (No rain should occur within 24 hrs after water activation) Can be used on false joint pavers Waterproof bag 15 Year Limited Warranty SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Nevada Tan, Oxford Grey & Ivory white Narrow joints sq ft ( sq m) Narrow joints sq ft ( sq m) Jet Black Wide joints sq ft ( sq m) Wide joints sq ft ( sq m) PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet in USA (Nevada Tan, Oxford Grey) 56 or 28 units per pallet in USA (Ivory White, Jet Black) 70 units per pallet in Canada (Nevada Tan, Oxford Grey) 70 or 35 units per pallet in Canada (Ivory White, Jet Black) Pallets can be stored outside Waterproof bags HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions AVAILABLE COLORS Nevada Tan Oxford Grey Ivory White Jet Black 15 YEAR LIMITED WARRANTY GRID AND FABRIC The Cleanest, Fastest and Easiest installation steps: Spread G2 Intelligent Polymeric Sand Sweep & Vibrate G2 Intelligent Polymeric Sand Sweep off excess G2 Intelligent Polymeric Sand Activate G2 Intelligent Polymeric Sand with water Polybind s brand new G2 Intelligent Polymeric Sand, is a simplified four easy step installation process, making it the cleanest, fastest and easiest in the industry. SEE VIDEO AT.COM To learn more, visit us online at Polybind.com 9 INSTALLATION EDGES

10 Polybind Sand POLYMERIC SAND FOR CONCRETE PAVER JOINTS UP TO 1 GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 10 SEE INSTALLATION INSTRUCTIONS PAGES 58-59

11 GRID AND FABRIC IDEAL FOR Residential use Concrete paver, wetcast products Sloping areas, pool surroundings, patios, walkways, driveways and more FEATURES For Drainage Applications, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) Waterproof bag 15 Year Limited Warranty SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Nevada Tan & Oxford Grey Narrow joints sq ft ( sq m) Wide joints sq ft ( sq m) PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet in USA 70 units per pallet in Canada Pallets can be stored outside Waterproof bags HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions AVAILABLE COLORS Nevada Tan Oxford Grey To learn more, visit us online at Polybind.com 11 HAZE FREE FORMULA 20% MORE POLYMERS 50% STRONGER 15 YEAR LIMITED WARRANTY SEE VIDEO AT.COM INSTALLATION EDGES

12 Polybind Complete POLYMERIC SAND FOR CONCRETE PAVING STONES & NATURAL STONES, FOR JOINTS UP TO 2 GRID AND FABRIC EDGES FOR DRAINAGE & NON-DRAINAGE SYSTEMS INSTALLATION To learn more, visit us online at Polybind.com 12 SEE INSTALLATION INSTRUCTIONS PAGES 60-61

13 GRID AND FABRIC IDEAL FOR Residential & commercial use Drainage and Non-Drainage (Overlays) applications Concrete paver, natural stone and wetcast products Streetscape, commercial work, steep slope, pool areas, patios, walkways, driveways, parking areas and more FEATURES Drainage base systems, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) Non-Drainage base systems (Overlays), sets within 24 hours after water activation at above 32ºF (0ºC) (No rain should occur within 24 hours after water activation) Can be used on false joint pavers Waterproof bag 15 Year Limited Warranty SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet in USA 70 units per pallet in Canada Pallets can be stored outside Waterproof bags HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions AVAILABLE COLORS Nevada Tan Nevada Tan & Oxford Grey Narrow joints sq ft ( sq m) Oxford Grey Wide joints sq ft ( sq m) To learn more, visit us online at Polybind.com 13 HAZE FREE FORMULA 20% MORE POLYMERS 50% STRONGER 15 YEAR LIMITED WARRANTY SEE VIDEO AT.COM INSTALLATION EDGES

14 Eurostone Bond POLYMERIC SAND FOR NATURAL STONE PAVER & COBBLESTONE JOINTS UP TO 1.5 GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 14

15 GRID AND FABRIC IDEAL FOR Pedestrian, residential & commercial use Plaza, streets, paths, paved sloping areas, driveway aprons, pool surroundings and many more scenarios FEATURES Drainage base systems, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) Non-Drainage base systems (Overlays), sets within 24 hours after water activation at above 32ºF (0ºC) (No rain should occur within 24 hrs after water activation) Extremely strong and water resistant In vehicular application stone must be interlocked or adhered to a concrete bed PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet Pallets can be stored outside HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions AVAILABLE COLORS Beige Slate Grey Ivory Black Diamond 20% SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Narrow joints sq ft ( sq m) Narrow joints sq ft ( sq m) Beige, Slate Grey & Ivory Black Diamond Wide joints sq ft ( sq m) Wide joints sq ft ( sq m) To learn more, visit us online at Polybind.com 15 MORE POLYMERS 50% STRONGER 15 YEAR LIMITED WARRANTY INSTALLATION EDGES

16 Gator Tile Sand POLYMERIC SAND FOR PORCELAIN TILE JOINTS UP TO 1 GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 16 SEE INSTALLATION INSTRUCTIONS PAGES 64-65

17 GRID AND FABRIC IDEAL FOR Residential & commercial use Pedestrian use Outdoor porcelain tile joints FEATURES Drainage base systems, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) Non-Drainage base systems (Overlays), sets within 24 hours after water activation at above 32ºF (0ºC) (No rain should occur within 24 hrs after water activation) For use with Gator Tile Systems only Waterproof bag 15 Year Limited Warranty PACKAGING Retail Size: 35 lbs (15.9 kg) 40 units per pallet Pallets can be stored outside Waterproof bags HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions SAND COVERAGE 35 lbs (15.9 kg) Quantity required depends on the shape and size of the porcelain tiles. 24" x 24" Tile with 1/8" (3.2 mm) joints Beige, Slate Grey & Ivory 220 sq ft (20.4 sq m) Black Diamond 190 sq ft (17.7 sq m) 24" x 24" Tile with 3/16" (4.8 mm) joints Beige, Slate Grey & Ivory 170 sq ft (15.8 sq m) Black Diamond 150 sq ft (13.9 sq m) 24" x 24" Tile with 1/4" (6.4 mm) joints Beige, Slate Grey & Ivory 125 sq ft (11.6 sq m) Black Diamond 110 sq ft (10.2 sq m) To learn more, visit us online at Polybind.com YEAR LIMITED WARRANTY USED FOR INSTALLATION AVAILABLE COLORS SEE VIDEO AT.COM Beige Slate Grey Ivory Black Diamond INSTALLATION EDGES

18 Polybind Dust POLYMERIC STONE FOR STONE JOINTS 1/2 TO 6 GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 18 SEE INSTALLATION INSTRUCTIONS PAGES 62-63

19 GRID AND FABRIC IDEAL FOR Residential use Pedestrian use Patios, walkways, pool decks and more Joints 1/2 to 6 wide FEATURES Drainage base systems, sets within 24 hours after water activation at above 59ºF (15ºC) (No rain should occur within 24 hours after water activation) Waterproof bag 15 Year Limited Warranty PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet in USA 70 units per pallet in Canada Pallets can be stored outside Waterproof bags HELPS PREVENT Weed sprouting Damages caused by insects Erosion due to climatic conditions COVERAGE PER BAG 50 lbs (22.7 kg) The quantity required depends on the shape and size of the stones as well as the width of the joints. Joints are about 1 to 2 (2.54 to 5.08 cm) wide and the stones are about 2 to 2-1/2 (5.08 cm to 6.35 cm) thick. AVAILABLE COLORS Tan 20 to 30 sq ft (1.86 to 2.79 sq m) Grey To learn more, visit us online at Polybind.com YEAR LIMITED WARRANTY XTRA BONDING XTRA STRENGTH XTRA DURABILITY FOR PEDESTRIAN USE ONLY CANNOT BE USED FOR VEHICULAR TRAFFIC SEE VIDEO AT.COM INSTALLATION EDGES

20 Gator Aqua Rock PERMEABLE STONE FOR PERMEABLE PAVER JOINTS GRADED ASTM NO.9 GRANITE STONE GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 20

21 GRID AND FABRIC IDEAL FOR Residential & commercial use Permeable paver joints and bedding material Concrete paver and wetcast products Driveways, parking lots, patios and more FEATURES Graded to meet ASTM No. 9 High strength granite stone for long-term use Helps collect roof and surface water run-off Reduction of storm water rate Calibrated for the majority of permeable pavers COVERAGE PER BAG Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. 50 lbs (22.7 kg) Bag for a 60 mm paver 20 to 25 sq ft (1.86 to 2.32 sq m) For large scale projects, is also offered in a 2,200 lbs Super-Sack format 2200 lbs (1000 kg) Super-Sack (for a 60 mm paver) 880 to 1100 sq ft (81.78 to sq m) To learn more, visit us online at Polybind.com 21 PACKAGING Retail Size: 50 lbs (22.7 kg) 56 units per pallet Retail Size : Super-Sack 2200 lbs (1000kg) 1 unit per pallet AVAILABLE COLOR Granite Grey INSTALLATION EDGES

22 Gator Base THE ONLY TECHNOLOGY SAVING 6" OF EXCAVATION, 6" OF COMPACTED AGGREGATE AND MUCH MORE GRID AND FABRIC SEE INSTALLATION INSTRUCTIONS PAGES EDGES INSTALLATION OVER 2 MILLION SQ. FT. INSTALLED Lock-N-Go (tongue-and-groove system) 10% thicker than the competition, 3/4 (1.9 cm) 25% faster to install, dimensions: 24 x 36 (60.96 cm to cm) R-Value of 3.6, highest in the industry Will reduce the number of freeze and thaw cycles The only system university tested, with a proven track record! Can be used for concrete pavers, natural stone, concrete slabs, porcelain tiles & clay pavers To learn more, visit us online at Polybind.com 22

23 Under License from Brock International-Patented and Patents Pending: FOR PEDESTRIAN USE ONLY Gator Base the evolution in foundation technology. It can be used for concrete pavers, natural stone, concrete slabs, clay pavers and outdoor porcelain tiles. It is 25% faster to install, offering a R-value of 3.6 and reduces the number of freeze and thaw cycles. Gator Base Display Stand GRID AND FABRIC FEATURES Equivalent to 288 lbs (130 kg) of crushed stone For pedestrian use only Save 6 (15 cm) of extra excavation Save 6 (15 cm) of compacted crushed stone Save on cost of truck and driver on the road Save on costly dumping fees Save on wear and tear on machinery Save on labor costs Save on overall installation time Increase profit COVERAGE Final dimensions at installation: 5.79 sq ft (0.53 sq m) 23.5 in x 35.5 in (60 cm x 90 cm) 3/4 in (1.90 cm) thick Weight per panel: 1.32 lbs (0.60 kg) IDEAL FOR: Open Spaces Small and large projects Up a hill Staircase landings Tight work spaces Narrow alleys Where material storage is prohibited in streets Where construction speed is critical Limited budget Concrete paver, slab, natural stone and porcelain tile projects Pedestrian applications such as: patio, sidewalk, landing, terraces, pool surrounding PACKAGING 10 units per pack 12 packs per pallet 120 units per pallet Gator Base Display Stand 25 W x 54.5 H x 32 D Tongue & Groove (Lock-N-Go) Evacuates water through the channel Manufactured using lightweight high-density polypropylene To learn more, visit us online at Polybind.com 23 INSTALLATION EDGES

24 GRID AND FABRIC Gator Base The only base technology saving 6 of excavation, 6 of compated aggregate and much more. Alliance Designer Products Inc. has introduced to the market a revolutionary technology for the foundations when installing concrete pavers, natural stones or porcelain tiles. This technology exhibits the memory characteristics of polypropylene and allows the material to retain its original installation. Gator Base design load transfer. The Gator Base with its interlocked paneling system, is engineered to support a load and disperse it into a very light load below the panel. The native soil feels little to no pressure when people walk on the paved surfaces. That Is How It Works! WAY In the pursuit of excellence, Alliance has retained the services of the University du Quebec engineering institute (ETS) in Montreal to perform testing on the Gator Base versus a traditional granular base. In conclusion; It can be stated that both systems are equivalent under static load and dynamic load. Gator Base panel is equipped with channels for water evacuation along a 1 slope as well as 5 drainage holes per 16 sq. in. For detail information on the installation steps please refer to page TRADITIONAL WAY Gator Base Units are Perfect for All Projects Open Spaces Small and large projects Up a hill Staircase landings Tight work spaces Narrow alleys Where material storage is prohibited in streets Where construction speed is critical Limited budget Concrete paver, slab, natural stone and porcelain tile projects Pedestrian applications such as: patio, sidewalk, landing, terraces, pool surrounding PAVER PAVER BEDDING SAND 1/2 Five (5) Gator Base panels are the equivalent of 1,440 lbs. of stone and they can be carried in one hand (equivalent to 28.9 sq. ft. filled with 6 of crushed stones). COMPACTED BEDDING SAND 1/2 FABRIC GF4,4 COMPACTED NATIVE SOIL EQUIVALENT (=) EDGES NO CRUSHED STONE FABRIC GF4,4 6" (15 CM) OF CRUSHED STONE COMPACTED NATIVE SOIL INSTALLATION For more information on the Gator Base panels or to get a copy of the University report, visit AllianceGator.com or please contact Alliance Designer Products Inc. technical department at / info@alliancegator.com To learn more, visit us online at Polybind.com 24 is engineered to support a dynamic load of up to 8 PSI or 1152 pounds on a 12 x 12 paver.

25 KEY DIFFERENCES BETWEEN A INSTALLATION AND A TRADITIONAL PAVER INSTALLATION Gator Base is the solution to the three biggest challenges faced by every hardscape installer: excavation, time and labor, and freeze/thaw cycles. And with over 2 million square feet already installed, contractors are clearly seeing the benefits of breaking the mold and trying something new! So what exactly are the differences between using Gator Base vs. installing pavers the old fashioned way? Keep reading because you re about to find out! Here are details on the three key differences between a Gator Base installation and a traditional paver installation. 1 - Less Excavation When excavating for a traditional paver installation, it s customary to reserve six inches for crushed stone. With a Gator Base installation, there s no need to do this. Here s why. The interlocking panels distribute all dynamic loads to a very wide area, practically eliminating any pressure on the ground. Essentially, one Gator Base panel is the equivalent to six inches of crushed stone! FUN FACT: A 144 lb. person produces a 1 PSI (pounds per square inch) load on a 12" x12" paver. Gator Base is engineered to support a dynamic load of up to 8 PSI (or 1,152 lbs.) on a 12 x12 paver! So now you re probably asking, but what about drainage? Contractors commonly believe that the crushed stone in a traditional installation is partly there to allow for water drainage (which ultimately prevents frost from heaving the pavers). Well, Gator Base has got you covered there, too! For proper drainage, each Gator Base panel is equipped with channels for water evacuation along a one degree slope. There are also five drainage holes per every 16-square inch. Properly compacted crushed stone hardly drains at all! Less excavation is a tremendous benefit offered by a Gator Base installation. Not only will you enjoy a time savings, but a cost savings on Six inches of crushed stone A truck and driver on the road Dumping fees Wear and tear on machinery See video (polybind.com/videos) 2 - Reduced Labor Excavation is one area where labor can be saved on a Gator Base job, however, Gator Base also drastically cuts down on the time it takes to perform an installation. With each panel weighing in at a mere 1.32 lbs. (600 g), moving them in and setting them down takes a matter of minutes! No more hauling in heavy aggregate material... 5 panels or 28.9 square feet of Gator Base (which weighs only 6.6 lbs. (3 kg)) replaces a whopping 1,440 lbs. (653 kg) of crushed stone (and all of the tedious hours of manual labor that comes along with it)! We recently filmed a side-byside Gator Base vs. traditional paver installation. The Gator Base project was completed 57% faster! By the time the crew started installing the polymeric sand on the Gator Base job, the crew working on the traditional job still had to: Complete the bedding sand Install the pavers Install the edging Compact the pavers And the list goes on! See video (polybind.com/videos) 3 - Protection From Freeze Thaw Cycles One of the most commonly asked questions we get on Gator Base is, how does it perform in climates that experience freeze/thaw cycles? As we noted above, crushed stone in a traditional installation really doesn t allow for water drainage and it is all too common to see frost heaving pavers when the temperatures drop. Well, Gator Base is specifically engineered to protect against the effects of freeze/thaw! One panel of Gator Base acts like a thermal blanket that insulates as well as 18 inches of crushed stone... making it three times more effective than crushed stone as an insulator! With an R-Value of 3.6 (per inch thickness), Gator Base will significantly reduce the impact of freeze and thaw cycles. So, are you ready to try something new for a change? Try the Gator Base way! Follow us on the blog and twitter to learn more on a multitude other leading articles of the industry. (blog.alliancegator.com) To learn more, visit us online at Polybind.com 25 The 10 packs carried on his head is the equivalent of 158 lbs (72 kg) or 34,560 lbs (15,676 kg) of crushed stone. GRID AND FABRIC INSTALLATION EDGES

26 Gator Tile System INNOVATIVE AND DURABLE SYSTEMS FOR OUTDOOR PORCELAIN TILE INSTALLATIONS GRID AND FABRIC EDGES INSTALLATION TO BEST UNDERSTAND SYSTEM, SEE VIDEO AT.COM/-TILE-SYSTEM/ To learn more, visit us online at Polybind.com 26 SEE INSTALLATION INSTRUCTIONS PAGES 64-65

27 What is the Gator Tile System? The Gator Tile Systems is a comprehensive line of products to help you install outdoor tile with precision, beauty and long-lasting stability. Easy to use, saving you time and money while giving you the most professional-looking results. GRID AND FABRIC Facilitates the installation of outdoor porcelain tiles Increases efficiency Equivalent to 288 lbs (130 kg) of crushed stone Replaces 6 in (15 cm) of compacted crushed stone Evacuates water through the channel Manufactured using lightweight high-density polypropylene Environment-friendly and 100 % recyclable Extremely durable, will not degrade in the ground Designed with a tongue-and-groove system Gator Base Insulation has an R-Value of 3.6 Will significantly reduce the number of freeze and thaw cycles PORCELAINE TILE 3/4" 3/4" BEDDING SAND 1/2 FABRIC GF4.4 COMPACTED NATIVE SOIL To learn more, visit us online at Polybind.com 27 SPACER INSTALLATION EDGES

28 Gator Tile System's 7 Components FABRIC GF4.4 Is ideal for drainage and prevents the bedding sand from migrating into the native soil. Replace concrete foundations and is engineered to replace an equivalent of 6 (15 cm) of compacted crushed stone Under License from Brock International- Patented and Patents Pending: X-TRA ADHESIVE Ensures mechanical binding and structural integrity of the system. Polybind X-TRA adhesive formula is specifically engineered to adhere to the Gator Spacers and tiles. SPACER Provides uniform spacing and unparalleled horizontal and vertical stability to the system. Available in joint sizes of 1/8, 3/16 and 1/4 (3,2 mm, 4,8 mm and 6,4 mm). GRID AND FABRIC TILE EDGE Reinforces the perimeter providing stability and creating a strong lateral support with a mechanical bond of the Gator Tile Edge and the Gator Base screws. Available in 3 sizes: joint widths of 1/8, 3/16, and 1/4 Gator Base SCREWS Fastening Gator Edge with the Gator Base Screws through the Gator Base reinforces the outside perimeter, creating a strong lateral support. Bedding Sand Gator Fabric Native Soil 5/8 (15 mm) height EDGES TILE POLYMERIC SAND The only polymeric sand for outdoor porcelain tile joints up to 1 (2.5cm). Once set, becomes very firm and locks between the tile joints while still retaining flexibility and providing a longlasting, durable jointing material. offered in beige, slate grey, ivory and black diamond. Available colors: Beige Slate Grey Ivory Black Diamond INSTALLATION To learn more, visit us online at Polybind.com 28 SEE VIDEO AT.COM

29 1/2 1/4 Gator Spacer PROVIDES UNIFORM SPACING, ALIGNMENT WITH HORIZONTAL AND VERTICAL STABILITY Available in three joint sizes (inches) Joint Width (mm) 1/8" (3.2 mm) 3/16" (4.8 mm) 1/4" (6.4 mm) 6 1/8 The spacer can be cut into either a half- or a quarter-unit (using an utility knife) to be used along the edge of a building or the Gator Tile Edge. Simply break the spacer bar s bridge to obtain a flat disk, when spacer is needed on larger porcelain tile. GRID AND FABRIC Porcelain Tile Polybind X-TRA adhesive penetrates into the concave holes, adhering the Porcelain tile to the Gator Tile Spacer, then hardens. This allows the tile to minimize any horizontal or vertical movements. Gator Spacer Calculator 24 x 24 tiles 24 x 48 tiles 16 x 32 tiles 36 x 36 tiles Polybind X-TRA adhesive Gator Spacer Gator Base sq.ft. X 0.4 =number of spacers sq.ft. X 0.35 =number of spacers sq.ft. X 0.75 =number of spacers sq.ft. X 0.56 =number of spacers To learn more, visit us online at Polybind.com 29 INSTALLATION EDGES

30 Gator Grid THE BEST SOLUTION, BIAXIAL GRID FOR SEGMENTAL RETAINING WALLS AND EROSION CONTROL GG BIAXIAL BIAXIAL GEOGRID STAIRCASE, LANDING AREA, LOW RETAINING WALL LBF/FT GRID AND FABRIC EDGES INSTALLATION biaxial Gator Grid GG 20-20*, a biaxial geogrid, provides strength, longevity, excellent stress transfer and prevents failure to the internal structure of your staircases, patios, landing areas, retaining walls and steep slopes. As a biaxial geogrid, GG 20-20* has a high molecular weight as well as high-tenacity polyester yarns which are woven in tension and finished with a PVC coating. APPLICATIONS Erosion control Patio internal structure Staircase internal structure Behind retaining walls General landscape BENEFITS Biaxial: can be installed in both directions Adds strength, stability and longevity Helps reduce stress and load transfer to the structure Soil separation for added stability GG x / box GG x / box GG x / pal GG x / pal To learn more, visit us online at Polybind.com 30 Gator Grid Gator Fabric Display Gator Fabric & Gator Grid Stand (30 W x 76.5 H x 30 D)

31 GG BIAXIAL BIAXIAL GEOGRID SEGMENTAL RETAINING WALL, EROSION CONTROL GG BIAXIAL BIAXIAL GEOGRID SEGMENTAL RETAINING WALL, EROSION CONTROL AND MORE NEW LBF/FT LBF/FT Gator Grid GG 30-30*, a biaxial geogrid, provides strength, longevity, excellent stress transfer and prevents failure of the internal structure of landing areas, retaining walls and steep slopes. As a biaxial geogrid, GG has a high molecular weight as well as high-tenacity polyester yarns which are woven in tension and finished with a PVC coating. Gator Grid GG 50-50*, a biaxial geogrid, provides strength, longevity, excellent stress transfer and prevents failure of the internal structure of retaining walls being single or multi levels and controlling erosion in steep slopes applications. As a biaxial geogrid, GG has a high molecular weight as well as high-tenacity polyester yarns which are woven in tension and finished with a PVC coating. GRID AND FABRIC APPLICATIONS Erosion control Behind retaining walls General landscape BENEFITS Biaxial: can be installed in both directions Adds strength, stability and longevity Helps reduce stress and load transfer to the structure Soil separation for added stability GG x 50 9 / box GG x / pal GG x / pal GG x / pal APPLICATIONS Retaining wall strtuctures Multi level wall structures Erosion control General landscape BENEFITS Biaxial: can be installed in both directions Adds strength, stability and longevity Helps reduce stress and load transfer to the structure Soil separation for added stability GG x / pal GG x / pal GG x / pal * Disclaimer for GG 20-20, GG and GG The soil composition may vary from location to location. Global stability of the soil has not been considered. It is the owner s responsibility to take into consideration the soil parameters indicated on the label and to ensure that the soil s properties meet construction standards. A soil analysis must be done before starting any wall project. Before the construction of your segmental wall and before using any type of Gator Grid and establishing the placement, consult a qualified local engineer and obtain a stamped plan. To ensure the structural integrity of your segmental retaining wall, follow manufacturer instructions and installation steps for the construction of your wall. These placement tables are not to be used on multi-tiered walls or in areas with excess water runoff, seepage or springs, unless first otherwise confirmed by a qualified local engineer. Additional Gator Grid than what appears on the label may be required in your application. This document should not be construed as engineering advice. We assume no liability of any kind if the instructions in the present disclaimer are not followed or if the owner s use of the product is different than the one for which it is intended. To learn more, visit us online at Polybind.com 31 INSTALLATION EDGES

32 Gator Fabric NON-WOVEN FABRIC FOR PAVER INSTALLATIONS AND RETAINING WALLS GRID AND FABRIC EDGES The best solution for drainage, separation, filtration and protection of any soil structure INSTALLATION To learn more, visit us online at Polybind.com 32

33 GF3.5 NON-WOVEN NON-WOVEN FABRIC FOR PAVER INSTALLATIONS AND RETAINING WALLS GF4.4 NON-WOVEN NON-WOVEN FABRIC FOR PAVER INSTALLATIONS AND RETAINING WALLS 80 LBF 100 LBF Gator Fabric GF 3.5** Non-Woven geotextile is ideal for drainage, filtration and will allow water flow in a paver or retaining wall applications. Its staple fibers are used for soil separation and drainage. They combine high durability along with excellent physical and hydraulic properties. It is non-biodegradable. Gator Fabric GF 4.4** Non-Woven geotextile is ideal for drainage, filtration and will allow water flow in a paver or retaining wall applications. Its staple fibers are used for soil separation and drainage. They combine high durability along with excellent physical and hydraulic properties. It is non-biodegradable and resistant to most soil chemicals. GRID AND FABRIC APPLICATIONS Drainage protection Erosion control Behind retaining walls General landscape BENEFITS Allows high-water flow (165 gallons per minute per foot) Soil separation for added stability High strength/dimensionally stable GF35NW x / box GF35NW x / box GF35NW x / pal GF35NW x / pal GF35NW x / pal GF35NW x / pal APPLICATIONS Drainage protection Erosion control Behind retaining walls General landscape BENEFITS Allows high-water flow (135 gallons per minute per foot) Soil separation for added stability High strength/dimensionally stable GF44NW x / box GF44NW x / box GF44NW x / pal GF44NW x / pal GF44NW x / pal GF44NW x / pal ** Disclaimer for GF3.5 and GF4.4 Information regarding the physical properties, performance and permitted use of Alliance Designer Products Inc. s Gator Fabric products is, to the best of our knowledge, reliable. However, Alliance Designer Products Inc. assumes no liability for the accuracy or completeness of this information or for its ultimate use. As Alliance Designer Products Inc. has no control over methods of use and field conditions, Alliance Designer Products Inc. disclaims all warranties, expressed or implied, including, without limitation, the warranties of merchantability and/or fitness for a particular purpose and as to quality. The final determination as to the appropriateness or suitability of any Gator Fabric product in any particular application rests with the end user and is the end user s sole responsibility. This document should not be construed as engineering advice. To learn more, visit us online at Polybind.com 33 INSTALLATION EDGES

34 GF8 POLYSPUN GF20 POLYSPUN POLYSPUN FOR GARDEN AND LANDSCAPE COVERINGS POLYSPUN FOR GARDEN AND LANDSCAPE COVERINGS 8 YEARS 20 YEARS GRID AND FABRIC Gator Fabric GF 8 polyspun is a geotextile that protects against the growth of weeds. It is specially formulated to resist deterioration due to exposure to ultraviolet light and is inert to commonly encountered soil chemicals. GF 8 polyspun fabric will not rot or mildew, and is nonbiodegradable. Comes with an 8-year warranty. APPLICATIONS Garden and landscape covering Mulch or decorative rock garden Separation barrier for landscape beds BENEFITS Creates a barrier that reduces weed growth Allows water, fertilizer and air to pass through Gator Fabric GF 20 polyspun is an excellent geotextile that protects against the growth of weeds. It is specially formulated to resist deterioration due to exposure to ultraviolet light and is inert to commonly encountered soil chemicals. GF 20 polyspun fabric will not rot or mildew, and is non-biodegradable. Comes with a 20-year warranty. APPLICATIONS Garden and landscape covering Mulch or decorative rock garden Separation barrier for landscape beds BENEFITS Creates a barrier that reduces weed growth Allows water, fertilizer and air to pass through EDGES GF8NW x / box GF8NW x / box GF8NW x / box GF8NW x / box GF8NW x / pal GF8NW x / pal GF20NW x / box GF20NW x / box GF20NW x / box GF20NW x / box GF20NW x / pal GF20NW x / pal INSTALLATION To learn more, visit us online at Polybind.com 34

35 GF5 WOVEN PROVIDES STABILITY AND SEPARATION OF SUBGRADE IN PAVER OR WALL FOUNDATIONS 200 LBF Gator Fabric GF 5 is a woven geotextile made from polypropylene yarns, forming a stable and durable network such that the yarns retain their relative position. It provides separation for good subgrades by preventing mixing of subgrade soils. A woven geotextile can achieve higher tensile strength at low elongation, known as high modulus. It is inert to biological degradation and resistant to naturally occurring chemicals, alkali and acid. APPLICATIONS Helps stabilize foundation of paver projects Can be applied for driveways, pathways, sidewalks and retaining walls Can also be used for ground cover and soil separation BENEFITS Improves long-term performance of almost any hardscape project Extra-resistant to punctures and tears Reduces extra excavation and backfill Cost-effective solutions for reinforcement applications Easy to install on worksites GF5W x / box GF5W x / pal GF5W x / pal GF5W x / pal GF5W x / pal CROSS-REFERENCE CHART FOR FABRICS AND GRIDS Alliance Gator Comparative Products Category Product Application SRW Tencate Hanes Strata Texel (Lydall) Synteen Tensar Carthage Mills Geostar Gator Fabric Gator Grid GF 3.5 (80 Lbf) Non-Woven GF 4.4 (100 Lbf) Non-Woven GF 5 (200lbf) Woven GF 8 (8 years) Polyspun GF 20 (20 years) Polyspun GG (1300 lbf/ft) Biaxial GG (2400 lbf/ft) Biaxial GG (3300 lbf/ft) Biaxial Drainage & Filtration Drainage & Filtration Stability & separation of subgrade in paver or wall foundations Separation & Weed Control Separation & Weed Control Staircase, landing area low retaining wall Segmental retaining wall, erosion control Segmental retaining wall, erosion control & more LS3 Mirafi 135 N Terratex no. 3 StrataTex ST-131 NW4 Mirafi 140 NC Terratex SD/4.5 StrataTex ST-140 SS5 Mirafi 500 X Terratex GS StrataTex SW-200 Polyspun 10 years Polyspun 15 years Universal Biaxial 3 series Biaxial 5 series Uni-Axial N/A N/A Miragrid XL Biaxial Miragrid 2XT Biaxial Miragrid 3XT Uni-Axial Pro Ion 8 years Pro Ion 20 years Terragrid SX-2020 Biaxial Terragrid SX-3030 Biaxial TEX-500 N/A N/A FX-30HS Geostar GN 31 TEX-700N N/A N/A FX-40HS Geostar GN 40 SX-90T N/A N/A Slit Film FX-55 GeoWeave 40 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Microgrid/ SG-150 Biaxial N/A Stratagrid 200 Uni-Axial BX-1100 T1 Biaxial BX-1200 T2 Biaxial BX-1500 T3 Biaxial Synteen SF 10 Biaxial Synteen SF 11 Biaxial Synteen SF 35 Uni-Axial Disclaimer for GF8, GF20 and GF5 Information regarding the physical properties, performance and permitted use of Alliance Designer Products Inc. s Gator Fabric products is, to the best of our knowledge, reliable. However, Alliance Designer Products Inc. assumes no liability for the accuracy or completeness of this information or for its ultimate use. As Alliance Designer Products Inc. has no control over methods of use and field conditions, Alliance Designer Products Inc. disclaims all warranties, expressed or implied, including, without limitation, the warranties of merchantability and/or fitness for a particular purpose and as to quality. The final determination as to the appropriateness or suitability of any Gator Fabric product in any particular application rests with the end user and is the end user s sole responsibility. This document should not be construed as engineering advice. To learn more, visit us online at Polybind.com 35 BX-1100 Biaxial BX-1500 Biaxial UX-1100/ UX-1400 Uni-Axial GBX-2020 Biaxial GBX-3030 Biaxial GX-300 Uni-Axial N/A MG-100 Biaxial HP-200 Uni-Axial GRID AND FABRIC INSTALLATION EDGES

36 STARTING A LUCRATIVE CLEANING Greenscapes Inc. CT-based and 30 years of being in business specializes in professional construction and design services, owner Tim Hara has discovered the key to leveraging pre-existing relationships and unlocking a new revenue source. In this case study, we ll unveil the secrets to success in what still remains unchartered territory for many contractors and installers... the cleaning and sealing business. & BUSINESS SEALING GRID AND FABRIC EDGES INSTALLATION Alliance Designer Products proud manufacturer of Polybind products Featured Greenscapes Project: A walkway designed with pavers and sealed with Polybind High Gloss sealer. This product drastically changes the look of the pavers. It s something the customer actually has to see in order to believe. -Says Tim Hara A New Opportunity Awaits... Cleaning and sealing can be tricky business. First, while there are a multitude of cleaners and sealers on the market, it s not always clear which products will be a good for each project. Then there s the application process. Working with sealer requires a certain level of know-how and skill (as well as cooperation from Mother Nature). One small error during the installation can cause a job to fail fast. Lastly, estimating cleaning/sealing projects can be complicated if you re not familiar with the products and application process. So it s understandable why many landscape and hardscape contractors steer clear of this kind of work. However... You re missing a huge opportunity for added revenue if you re not offering these services! In our recent interview with Tim Hara, owner of Greenscapes Inc. in Hebron, CT, we collected some inspiring insights on his company s success with cleaning and sealing... and now it s time to share them with you! To learn more, visit us online at Polybind.com 36 Product Knowledge Continuing education and staying on top of what s new in the industry is an integral piece of the Greenscapes business model. Not only is the company ICPI- and NCMA-certified, but Tim and his team know how to utilize their resources when it comes gaining product knowledge. While the crew has been using Alliance Designer Products cleaners and sealers for a solid three years, they still have questions from time to time. And when questions arise, they go straight to the source and turn to the Alliance support team for answers.

37 One of the main reasons I m loyal to Alliance So yes, there will be days you get stuck inside. Designer Products is the support I receive. A But you can still make productive use of your local rep is always available to quickly answer time! Whether you do some online training questions and that s extremely important to or research ways to creatively market your me, explains Tim. new cleaning/sealing business, professional development is the perfect way to keep busy At the end of the day, your level of product when bad weather strikes. knowledge will ultimately determine your level of success in the cleaning and sealing A process for estimating should also be a business. So where do you begin? We ve put consideration upon entering the cleaning and together a quick list of resources to get you sealing business. Time will need to be invested started: Sealing Gone Wrong, Sealing Natural in visiting job sites because, as Greenscapes Stone, The Ultimate Sealer Cheat Sheet & The has learned with experience, there is not a Alliance Blog. (blog.alliancegator.com) cookie cutter approach to estimating. The One of the main reasons I m loyal to Alliance Designer Products is the support I receive. A local rep is always available to quickly answer questions and that s extremely important to me, explains Tim. Equipment After you ve learned the products, it s time to set yourself up with the tools for success (literally). Part of Greenscapes commitment to the cleaning and sealing business is investing in the right equipment. According to Tim, having a reliable sprayer is of utmost importance. (We typically recommend an HVLP type sprayer like the Chapin Xtreme.) Some other tools you ll want to consider: a pressure washer, solventbased rollers, water- based rollers, brushes, and protective gear for handling products. Alliance Designer Products Cleaning & Sealing Quote Worksheet provides a great roadmap to estimating. You can download a free copy at: alliancegator.com/quote The job site visit is also a great time to gain insight into the client s expectations...and help set them accordingly! This is especially important for sealing jobs. Below is a list of factors you can review with each client to help drill down which product(s) best matches their sealer needs. Planning & Estimating Common Considerations Weather can pose a variety of scheduling Customers preference or requests challenges, so it s important to know Environment (indoor/outdoor, ambient and understand how rain and extreme temperature, weather conditions etc.) temperatures can affect a sealing project. When planning, in most cases, a sealer should only be applied to pavers that are completely dry and no rain is in the forecast for hours. However, cleaning is typically ok with rain showers after 12 hours. Level of maintenance Environmental/ governmental requirements Time between resealing Final color Cost Ease of application And as a rule of thumb, F (15-27 C) degrees is an ideal temperature range. If these conditions don t exist on the day of your How consistent the sealer is across the application How the sealer cures project, it s time to readjust your plans! To learn more, visit us online at Polybind.com 37 Marketing Once you re ready to start cleaning and sealing, you ll want to target new business by promoting these services in all of your marketing efforts. This may include: updating your website, making announcements on social media, or launching a special campaign. While it may take some time to gain traction in acquiring brand new business, your existing customers are a gold mine leads! For all patio or sidewalk installations, we follow-up with the customer six months later by sending an about cleaning and sealing, shares Tim. This has been a very successful strategy for Greenscapes as it generates the majority of their cleaning and sealing business. Another piece of marketing advice from Greenscapes: show and tell! One of Tim s favorite sealers to use on projects is the Alliance Designer Products sealers family. For customers who are looking for color or sheen enhancement on their pavers, an actual sealed sample is extremely effective. This product drastically changes the look of the pavers. It s something the customer actually has to see in order to believe. Recap Launching a successful cleaning and sealing business can happen... it certainly has for Greenscapes! Through education, planning, and marketing, you ll be well on your way to discovering added revenue in a niche that many contractors avoid. The business is yours for the taking! Are you ready? Greenscapes Inc. 15 Teichert Lane, Hebron, CT Follow us on our blog post to learn more about: The Alliance Blog. blog.alliancegator.com GRID AND FABRIC INSTALLATION EDGES

38 Polybind Seal SOLVENT-D FOR DRY CAST CONCRETE PAVERS PROTECT & ENHANCE YOUR INVESTMENT GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 38 SEE INSTALLATION INSTRUCTIONS PAGES 70-71

39 Solvent-based Sealers For dry cast concrete pavers Wet Look High Gloss Vibrant Color Enhancer Satin Look Low Gloss Subtle Color Enhancer Resealer Revives Look GRID AND FABRIC Polybind Wet Look sealer is made from acrylic based polymers, thus reducing the oil and dirt penetration, as well as protecting the concrete pavers from the corrosion of de-icing salt. Specifically formulated to be used on unsealed surfaces only. FEATURES Protects and enhances look Easier to clean and maintain Solvent-based Film-former Joint stabilizer FOR WET LOOK, SATIN LOOK AND RESEALER Polybind Satin Look sealer is made from acrylic based polymers, thus reducing the oil and dirt penetration, as well as protecting the concrete pavers from the corrosion of de-icing salt. Specifically formulated to be used on unsealed surfaces only. FEATURES Protects and enhances look Easier to clean and maintain Solvent-based Film-former Joint stabilizer HELPS RESIST Corrosion from de-icing salt Ultraviolet rays effects Motor oil and grease stains COVERAGE Seals approx. 175 sq ft (16 sq m) per gallon Will vary depending on porosity of pavers PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet To learn more, visit us online at Polybind.com 39 Polybind Resealer will penetrate the formula of the existing sealer and reactivate the molecules to create a rejuvenated seal to protect the paver surface. Thus reducing the penetration of oil and dirt, as well as protecting them from de-icing salt. FEATURES Easier to clean and maintain Solvent based Revives look Can be applied over Polybind Wet and Satin Look finishes SEE VIDEO AT.COM INSTALLATION EDGES

40 Polybind Eco Seal WATER-D FOR DRY CAST CONCRETE PAVERS PROTECT & ENHANCE YOUR INVESTMENT +COLOR ENHANCER +COLOR ENHANCER GRID AND FABRIC Polybind Eco Seal is an acrylic copolymer used to seal concrete pavers. It penetrates deep into the concrete paver pores, thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt. FINISH High gloss Vibrant color enhancement Eco Seal High Gloss +COLOR ENHANCER FINISH Low gloss Vibrant color enhancement Eco Seal Low Gloss +COLOR ENHANCER EDGES INSTALLATION ECO SEAL COLOR ENHANCER WATER-D FEATURES Helps resist corrosion from de-icing salt, ultraviolet rays effects, motor oil and grease stains Works above 40ºF (5ºC) Breathable Film former Joint stabilizer Will not discolor Rapid Installation Low VOC Color enhancer To learn more, visit us online at Polybind.com 40 COVERAGE Coverage will vary depending on joint size and porosity of the surface of the pavers (approx sq. ft. per gallon) PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet

41 GRID AND FABRIC Eco Seal High Gloss Polybind Eco Seal is an acrylic copolymer used to seal concrete pavers. It penetrates deep into the concrete paver pores, thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt. FINISH HIgh gloss No color enhancement FEATURES Helps resist corrosion from de-icing salt, ultraviolet rays effects, motor oil and grease stains Works above 40ºF (5ºC) Breathable Film former Joint stabilizer Will not discolor Rapid Installation Low VOC Eco Seal Low Gloss FINISH Low gloss No color enhancement ECO SEAL WATER-D COVERAGE Coverage will vary depending on joint size and porosity of the surface of the pavers (approx sq. ft. per gallon) PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box, 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet To learn more, visit us online at Polybind.com 41 Eco Seal Zero Gloss FINISH Zero gloss No color enhancement SEE VIDEO AT.COM INSTALLATION EDGES

42 DELUXE SERIES THE PREMIERE LINE OF SEALANTS FOR EVERY CONCEIVABLE APPLICATION +COLOR ENHANCER MULTI-PURPOSE GRID AND FABRIC EDGES Polybind Deluxe Series Sealer for Natural Stone zero gloss, water based sealer with color enhancer is made of silicone based polymers. This sealer penetrates deep into the natural stones, thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt. FEATURES Easier to clean and maintain Non film-former Work above 32ºF (0ºC) Color enhancer Water-based Zero gloss Natural Stone Zero Gloss +COLOR ENHANCER WATER-D COVERAGE Granite: sq. ft. per gal. Travertine: sq. ft. per gal. Limestone: sq. ft. per gal. Sandstone: sq. ft. per gal. Bluestone: sq. ft. per gal. Coverages are approximate and will vary based on stone porosity, joint width and other factors. PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet Natural Look Natural Look Finish, Zero Gloss MULTI-PURPOSE Polybind Deluxe Series Natural Look finish Sealer, zero gloss, water based sealer for natural stones is made from fluorochemical polymers. This sealer penetrates deep into the concrete pavers, walls, masonry and natural stones, thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt. FEATURES Non film forming Works at above 32 F (0 c) Water repellent Applicable on damp surfaces COVERAGE Seals approx. 175 sq ft (16 sq. m.) per gallon Zero VOC Water base sealer WATER-D PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet INSTALLATION To learn more, visit us online at Polybind.com 42 SEE VIDEO AT.COM

43 DELUXE SERIES +COLOR ENHANCER Polybind Deluxe for Wet Cast products with a Natural look finish, zero gloss and water-based is made from fluorochemical polymers. This sealer penetrates deep into the Wet Cast, thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt. FEATURES Easier to clean and maintain Non film-former Works at above 32 F (0 c) Wet Cast Natural Look Finish Zero Gloss COVERAGE Seals approx. 175 sq ft (16 sq. m.) per gallon WATER-D Natural look Water-Based, Zero Gloss PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet Polybind Deluxe for Wet Cast products with a low gloss, joint stabilizer, solvent-based sealer with color enhancer is made from acrylic-based polymers. This sealer is film forming for Wet Cast products, that will reduce the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt. FEATURES Easier to clean and maintain Film-former Low Gloss Wet Cast Low Gloss +COLOR ENHANCER COVERAGE Seals approx. 175 sq ft (16 sq. m.) per gallon PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet To learn more, visit us online at Polybind.com 43 Solvent-based Color enhancer SOLVENT-D SEE VIDEO AT.COM GRID AND FABRIC INSTALLATION EDGES

44 Polybind Clean FOR CONCRETE PAVERS, WET CAST PRODUCTS AND NATURAL STONES GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 44 SEE INSTALLATION INSTRUCTIONS PAGES 68-69

45 STRONGER CLEANING FORMULA BUT GENTLE TO THE PAVERS SHAMPOO Polybind Clean Shampoo removes groundin dirt from the surface of concrete pavers & natural stones. It will make the pavers, patio slabs, walls and natural stones look clean and vibrant. FEATURES Removes penetrated dirt Restores the elements to their natural color No muriatic acid in product Washes off with water PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet COVERAGE Cleans approx. 375 sq ft (35 sq m) per diluted gallon EFFLORESCENCE Polybind Efflorescence Cleaner will remove any efflorescence stains trapped in the concrete pavers & natural stone pores. It will make the pavers look more clean and vibrant without discoloring or damaging the paver surface. This efflorescence cleaning is a necessary step before a sealer is applied. The sealer will be able to get a deeper penetration into the now clean pores. FEATURES Removes efflorescence from the surface of concrete pavers and natural stones No hydrochloric acid in product Washes off with water PACKAGING Retail size: 1 US gallon (3.78 L) & 5 US gallon (18.9 L) 4 units of 1 US gallon (3.78 L) per box 24 boxes per pallet 48 units of 5 US gallon (18.9 L) per pallet COVERAGE Cleans approx. 200 sq ft (18 sq m) per gallon To learn more, visit us online at Polybind.com 45 X-TRA OIL AND GREASE REMOVER Polybind X-TRA Oil and Grease Remover easily removes tough stains from motor oil, cooking oil, grease, wax, and more. Just shake it, spread it on the stain, let it dry, and sweep it off. Rinsing is needed if product has aged. Use it on concrete, brick, stone, composite decking, and more. Do not use on asphalt (blacktop). Polybind X-TRA Oil and Grease Remover is biodegradable and phosphate-free. FEATURES No scrubbing, no rinsing, no mess Shake bottle before applying to stain, allow to dry completely to powder, sweep product off. Easily lifts & absorbs embedded oil stains as it dries from liquid to powder Not recommended for synthetic oil stains. PACKAGING Retail size: 1 quart (946 ml) 6 units per box / 24 boxes per pallet COVERAGE Approximately 6 sq ft (0.56 sq. m.) SEE VIDEO AT.COM GRID AND FABRIC INSTALLATION EDGES

46 RUST REMOVER RUBBER, PAINT & TAR REMOVER + EFFLORESCENCE & SLURRY REMOVER GRID AND FABRIC EDGES Polybind Rust Remover is effective in removing rust from the surface of concrete pavers, wet cast products & natural stones. FEATURES Washes off with water Contains no muriatic acid Removes the spots caused by steel, water build up fertilizer, etc. Easy to use PACKAGING Retail size: 1 quart (946 ml) 6 units per box / 24 boxes per pallet Polybind Rubber, Paint & Tar Remover + is effective in removing rubber, oil-based paint and tar from the surface of concrete pavers, wet cast & natural stones. Can be use as a cleaning agent for tools when working with Gator Rock Bond or to re-emulsify any sealer type. FEATURES Washes off with water Easy to use Emulsify some sealers Remover & cleaner for bonding agent Cleaning sealing tools such as sprayer PACKAGING Retail size: 1 quart (946 ml) 6 units per box / 24 boxes per pallet PROFESSIONAL GRADE Gator Efflorescence & Slurry Remover will remove any efflorescence stains trapped in the concrete pavers, wet cast & natural stone pores. It will make the pavers look more clean and vibrant without discoloring or damaging the paver surface. This efflorescence cleaning is a necessary step before a sealer is applied. Ideal Mixture: 8 parts water 1 part product. Further dilution is possible. You must test all dilutions on small inconspicuous area of 4 sq. ft. to insure no etching of the surfaces. Please read all instructions before applying this product. FEATURES Slurry remover Removes efflorescence from the surface of concrete pavers, wet cast products & natural stones Cleans approx sq.ft. (167 sq. m.) Washes off with water This product will etch pavers if not diluted accordingly PACKAGING 48 units of 5 US gallon (18.9 L) per pallet INSTALLATION To learn more, visit us online at Polybind.com 46 SEE VIDEO AT.COM

47 & DISPLAY STAND GRID AND FABRIC To learn more, visit us online at Polybind.com 47 INSTALLATION EDGES

48 Polybind X-TRA Performance FASTEST SETTING GLUE IN THE INRY GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 48

49 X-TRA PERFORMANCE POLYURETHANE, LOW VOC GLUE DISPLAY STAND X-TRA Polyurethane Adhesive, Low VOC is one of the strongest polyurethane adhesives on the market. It is specially formulated for overlays, pool copings, steps and wall caps, concrete pavers, wet cast, natural stones, retaining walls, masonry units and bricks. X-TRA Polyurethane Adhesive, Low VOC is formulated to provide a permanent bond in 24 hours to the above materials if properly installed W x 59 H x D GRID AND FABRIC COVERAGE For approximately 1/4 bead 10 oz (296 ml): lin.ft ( lin. m) 28 oz (828 ml): lin.ft (24-27 lin. m) X-TRA ADHESIVE APPLICATIONS VOC Compliant Works above 32 F / 0 C Concrete Pavers & Bricks Dry & Damp Services Retaining Walls Masonry Units Wet cast & natural stones Waterproof Overlays & Pool Coping Steps & Wall Caps Fire Pits (up to 400 F / 204 C) Permanent Bond in 24 hours Xtra Bond Strength (up to 3 times the strength of conventional adhesives) Xtra Durability against torsion and tension PACKAGING 10 oz (296 ml), 12 cartridges/box, 90 boxes/pallet 28 oz (828 ml), 12 cartridges/box, 60 boxes/pallet To learn more, visit us online at Polybind.com 49 SEE VIDEO AT.COM X-TRA POLYURETHANE ADHESIVE LOW VOC INSTALLATION EDGES

50 Gator Rock Bond KEEPS STONES IN PLACE ROCK BINDER CREATES A DURABLE, PERMEABLE AND DECORATIVE SURFACE. THE FINISHING TOUCH FOR ANY HARDSCAPE PROJECT. GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 50 SEE INSTALLATION INSTRUCTIONS PAGES 71

51 ROCK BOND BINDER KIT ROCK BOND LIQUID AGENT GRID AND FABRIC Gator Rock Bond is a one component binder, that when mixed with riverstone creates a durable yet solid permeable and decorative surface. Great for garden pathways where erosion and drainage is a concern. FEATURES Porous and permeable Keeps stones in place Reduce maintenance and clean-up Durable in extreme conditions COVERAGE 1 kit, at 1/2 (13 mm) surface thickness, will cover approx. 8 to 10 sq.ft. (0.75 to 0.9 sq.m.) INCLUDED IN PAIL Liquid binding agent (1/2 quart / 473 ml) and Riverstone (40 lbs / 18.2 kg) PACKAGING Retail size: 1/2 quart (473 ml) binding agent and 40 lbs (18.2 kg) of rock 48 kits per pallet Riverstone (minimum 1/2 ) Gator Rock Bond is a one component binder, that when mixed with clean and dry riverstone, granite, limestone or marble creates a durable yet solid permeable and decorative surface. Great for garden pathways where erosion and drainage is a concern. FEATURES Porous and permeable Keeps stones in place Reduce maintenance and clean-up Durable in extreme conditions To learn more, visit us online at Polybind.com 51 COVERAGE One (1) US gal. (3.78 L) mixed with 320 pounds (145 kg) of dry clean stone will cover 80 sq.ft. (7.4 m2 ) at 1/2 (13 mm) thickness. TYPES OF ROCK THAT CAN BE USED WITH ROCK BOND Riverstone Granite Limestone Marble (1/8 to 3/8 )(3 to 10mm) These rocks have to be clean, free of dust & 100% dry. PACKAGING Retail size: 1 US gallon (3.78 L) 4 units of 1 US gallon (3.78 L) per box / 24 boxes per pallet SEE VIDEO AT.COM INSTALLATION EDGES

52 GRID AND FABRIC EDGES PATHWAY STABILIZER STONE BOND XP IS A UNIQUE BLEND OF ACRYLIC POLYMERS FOR USE AS A PATHWAY STABILIZER ON DECOMPOSED GRANITE (DG). PATHWAY STABILIZER INSTALLATION To learn more, visit us online at Polybind.com 52 SEE INSTALLATION INSTRUCTIONS PAGES 71

53 STONE BOND XP EASY 1 COAT APPLICATION STONE BOND XP Gator Stone Bond XP is a unique blend of polymers designed to bind together a wide variety of small aggregates commonly referred to as decomposed granites (dg): pathway mixes, crusher runs, concrete sand, etcetera. FEATURES Easy one-coat process Creates a strong bond on a wide variety of aggregates Resists surface erosion from both rain water and foot traffic COVERAGE Residential pedestrians: 15 sq ft / 1 US gal. ( 3.78L) Commercial pedestrians: 10 sq ft / 1 US gal. ( 3.78L) BENEFITS Ready to use right out of the container Easy-to-apply one-coat application Reduces dust, gravel migration and erosion Allows the use of Patio/Pathway year round No special tools or skills required to build Build using local aggregates Will not harm plants or aquatic life EPA-compliant Gator Stone Bond XP is sold in Canada and USA. To learn more, visit us online at Polybind.com 53 SEE VIDEO AT.COM GRID AND FABRIC INSTALLATION EDGES

54 Edges Nails and Screws Polybind Flex and Rigid edges with a unique Twist & Lock system, engineered with supported triangular angles at all key points, which provide a strong lateral support, essential for the load transfer. EDGE FLEX AND RIGID GRID AND FABRIC EDGES INSTALLATION To learn more, visit us online at Polybind.com 54

55 EDGE MINI SCREWS RIGID CAN TURN FLEXIBLE IN 3 EASY STEPS 1 CUT 2 BEND 1 / 25 mm height Edge Mini is made with 100 % Polyethylene. This will give it greater strength as well as provide good flexibility for pavers, natural stone and all types of slabs. It is easy to use and quick to install. Edge Mini model for applications of 1 that can be used for natural stone and all type of slabs in walkways, patios, paths, etc. Gator Base Bedding Sand Gator fabric Native Soil 3 INSTALL TILE EDGE Fastening Polybind Edge with the Gator Base Screw through the Gator Base reinforces the outside perimeter, creating a strong lateral support. Gator Base Screws are a required component on any Gator Base install. EDGE DISPLAY STAND GRID AND FABRIC CUT HERE TWIST & LOCK CONNECTION Edge Flex and Rigid are made with 100% Polypropylene Copolymer. This gives it great strength as well as providing greater flexibility. We have a Rigid model which is ideal for straight applications and a Flex model that can be used for all curved applications such as walkways, paths, entrances etc. Both the Rigid and Flex can be locked together with the Twist & Lock connection system. The Rigid could be transformed in a partial Flex by cutting the bridge support. 5/8 / 15 mm height The Gator Tile Edge is the fully customizable solution to run around the perimeter of your finished porcelain tile installation, providing stability and strong lateral support. The Gator Edge is made with 100 % polyethylene. When using any of the Gator Edging on the Gator Base they must be fastened with Gator Screws only. NAILS Polybind Nails are high quality nails which are available in lengths of 10 and 12, common or spiral models. Polybind Nails are designed for use with all Edge types. To learn more, visit us online at Polybind.com 55 Now easy-to-fill with side door Edge Display Stand 28 W x 98 H x 15 D SEE VIDEO AT.COM INSTALLATION EDGES

56 POLYMERIC SAND BY/PAR ALLIANCE DESIGNER PRODUCTS Simplified 4EASY STEPS Installation Polybind s brand new G2 Intelligent Polymeric Sand, is a simplified four easy steps installation process, making it the cleanest, fastest and easiest in the industry. GRID AND FABRIC EDGES INSTALLATION SAND G2 FOR TRADITIONAL DRAINAGE SYSTEMS Important Notes: A Drainage Base application, using SAND G2. Pavers and slabs must be installed according to ICPI Tech Spec #2 non-overlay ( org) before SAND G2 installation. B Always refer to the latest SAND G2 Technical Data Sheet at Polybind.com before installing SAND G2. C Pavers sides and top surfaces must be completely dry. Do not apply if the paver surface is damp or wet. The damp or wet WATER ACTIVATION FOR SAND G2 Important Notes A Work in manageable sections, ideally about 50 sq. ft. at a time, depending on temperature. B Do not allow G2 Intelligent SAND to wash out of joint. C Never allow paved surface to dry out during the water activation phase. D Watering must be started at the lowest point of the paved surface 50 sq. ft. (4.7 sq. m.) section for 1 minute. E Use a watering gun connected to a hose. Set to shower. surface will cause SAND G2 to prematurely activate and will lead to the polymers sticking on the paver surface. D Do not apply if the paver joints are damp or wet. This will prevent the SAND G2 from properly sliding into the joints and obtaining very densely packed joints, which is critical to the product s performance. E Drainage base systems, SAND G2, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation) F Avoid excessive watering or flooding of paver surface. G For all paver surfaces, and particularly around in-ground pools, there must be a slope of 1/8 inch (3 mm) per linear foot away from the edge of the pool or structures to ensure optimal performance of the SAND G2. H For the pool coping units, it is mandatory to use mortar in the To learn more, visit us online at Polybind.com 56 joints. For the rest of the paver installation around the pool, you can use SAND G2. I Install SAND G2 a minimum of 1/8 inch (3 mm) below the paver surface or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tires. Joints should be filled up to 1/8 inch (3 mm) below the edge or chamfer. J Do not sweep SAND G2 over asphalt.

57 BY/PAR ALLIANCE DESIGNER PRODUCTS SAND G2 Installation Steps (for a new paver surface) Spread G2 Intelligent SAND with hard-bristle broom. Make sure the G2 Intelligent SAND completely fills the joints. Do not use other materials in the joints. Leave a layer of G2 Intelligent SAND on the surface to aid in the vibrating and consolidation of G2 Intelligent SAND into joints. 1 Vibrate the G2 Intelligent SAND into the paver joints using a vibratory plate compactor. A protective pad is recommended. A roller compactor is best for slab installation. Joints should be filled up to 1/8 inch (3 mm) below the edge or chamfer. It is best to compact in several directions to ensure there are no air gaps or voids in the joints. Repeat steps 1 and 2 to ensure joints are filled and consolidated. Narrow joints require more care to completely fill. 2 Sweep off excess G2 Intelligent SAND from the paved surface, first with a hard-bristle broom, then a soft-bristle broom. Take care to leave the height of the polymeric sand at least 1/8 inch (3 mm) below the edge or chamfer of the paver. SAND G2 Installation Steps (for an existing paver surface) Activate G2 Intelligent SAND by showering 50 sq. ft. (4.5 sq. m.) section for 1 minute, starting at the lowest point. Once all the sections are activated, if needed rinse off any debris that would be on the total paver surface. When using G2 Intelligent SAND to replace existing jointing materials, old jointing materials need to be completely cleaned out of the joints and pavers completely dry before installing G2 Intelligent SAND. Be careful not to disturb the bedding material under the pavers. Follow steps 1 to 4 of G2 Intelligent SAND installation steps for a new paver surface. SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Narrow joints sq ft ( sq m) Nevada Tan & Oxford Grey POLYMERIC SAND Wide joints sq ft ( sq m) 3 FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION SAND G2 is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. The concrete pavers must be installed on a drainage base system composed of 2 layers. The upper layer can have a maximum of 1 inch of bedding sand. The lower layer must have a minimum of 6 inches of crushed stone 0 3/4 (0 20 mm) compacted at 98 % Proctor density. (See diagrams). (JOINT IS COMPLETELY FILLED WITH SAND G2) To learn more, visit us online at Polybind.com 57 4 GRID AND FABRIC INSTALLATION EDGES

58 COMPLETE BY/PAR ALLIANCE DESIGNER PRODUCTS Simplified 4EASY STEPS Installation Polybind s brand new G2 Intelligent Polymeric Sand, is a simplified four easy steps installation process, making it the cleanest, fastest and easiest in the industry. GRID AND FABRIC COMPLETE G2 FOR DRAINAGE AND NON-DRAINAGE SYSTEMS Important Notes A-1 Drainage Base application, using COMPLETE G2. Pavers and slabs must be installed according to ICPI Tech Spec #2 non-overlay (www. icpi.org) before COMPLETE G2 installation. A-2 Non-Drainage (overlay) application using COMPLETE G2. Remove all loose and fragile concrete and compact the substrate. Cover the ground with a Gator Fabric GF 4,4, refill with crushed stone, and compact it. ICPI recommends 2 inches diameter drainage holes spaced approximately 10 feet apart and at the lowest elevations in the concrete slabs. Holes should be filled with #8 stone and covered with a 1 foot x 1 foot patch of Gator Fabric GF 4,4. Drilled holes should allow any water entering the bedding layer to freely flow out. B Always refer to the latest COMPLETE G2 Technical Data Sheet at Polybind.com before installing COMPLETE G2. C Pavers sides and top surfaces must be completely dry. Do not apply if the paver surface is damp or wet. The damp or wet surface will cause COMPLETE G2 to prematurely activate and will lead to the polymers sticking on the paver surface. D Do not apply if the paver joints are damp or wet. This will prevent the COMPLETE G2 from properly sliding into the joints and obtaining very densely packed joints, which is critical to the product s performance. E-1 Drainage base systems, COMPLETE G2, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation). E-2 Non-Drainage base systems (Overlays), Only use COMPLETE G2, it sets within 24 hours after water activation at above 32ºF (0ºC) (No rain should occur within 24 hrs after water activation). F Avoid excessive watering or flooding of paver surface. G For all paver surfaces, and particularly around in-ground pools, there must be a slope of 1/8 inch (3 mm) per linear foot away from the edge of the pool or structures to ensure optimal performance of the COMPLETE G2. H For the pool coping units, it is mandatory to use mortar in the joints. For the rest of the paver installation around the pool, you can use COMPLETE G2. I Install COMPLETE G2 a minimum of 1/8 inch (3 mm) below the paver surface or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tires. Joints should be filled up to 1/8 inch (3 mm) below the edge or chamfer. J Do not sweep COMPLETE G2 over asphalt. EDGES INSTALLATION WATER ACTIVATION FOR COMPLETE G2 Important Notes A Work in manageable sections, ideally about 50 sq. ft. at a time, depending on temperature. B Do not allow G2 Intelligent COMPLETE to wash out of joint. C Never allow paved surface to dry out during the water activation phase. D Watering must be started at the lowest point of the paved surface 50 sq. ft. (4.7 sq. m.) section for 1 minute. E Use a watering gun connected to a hose. Set to shower. To learn more, visit us online at Polybind.com 58

59 BY/PAR ALLIANCE DESIGNER PRODUCTS COMPLETE G2 Installation Steps (for a new paver surface) Spread G2 Intelligent COMPLETE SAND with hard-bristle broom. Make sure the G2 Intelligent COMPLETE SAND completely fills the joints. Do not use other materials in the joints. Leave a layer of G2 Intelligent COMPLETE SAND on the surface to aid in the vibrating and consolidation of G2 Intelligent COMPLETE SAND into joints. 1 Vibrate the G2 Intelligent COMPLETE SAND into the paver jointsusing a vibratory plate compactor. A protective pad is recommended. A roller compactor is best for slab installation. Joints should be filled up to 1/8 inch (3 mm) below the edge or chamfer. It is best to compact in several directions to ensure there are no air gaps or voids in the joints. Repeat steps 1 and 2 to ensure joints are filled and consolidated. Narrow joints require more care to completely fill. 2 Sweep off excess G2 Intelligent COMPLETE SAND from the paved surface, first with a hard-bristle broom, then a soft-bristle broom. Take care to leave the height of the polymeric sand at least 1/8 inch (3 mm) below the edge or chamfer of the paver. COMPLETE G2 Installation Steps (for an existing paver surface) Activate G2 Intelligent COMPLETE SAND by showering 50 sq. ft. (4,5 sq. m.) section for 1 minute, starting at the lowest point. Once all the sections are activated, if needed rinse off any debris that would be on the total paver surface. When using G2 Intelligent COMPLETE SAND to replace existing jointing materials, old jointing materials need to be completely cleaned out of the joints and pavers completely dry before installing G2 Intelligent COMPLETE SAND. Be careful not to disturb the bedding material under the pavers. Follow steps 1 to 4 of G2 Intelligent COMPLETE SAND installation steps for a new paver surface. SAND COVERAGE 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Nevada Tan, Oxford Grey & Ivory white Narrow joints sq ft ( sq m) Narrow joints sq ft ( sq m) COMPLETE Jet Black Wide joints sq ft ( sq m) 3 Wide joints sq ft ( sq m) FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION COMPLETE SAND G2 is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. The concrete pavers must be installed on a drainage base system composed of 2 layers. The upper layer can have a maximum of 1 inch of bedding sand. The lower layer must have a minimum of 6 inches of crushed stone 0 3/4 (0 20 mm) compacted at 98 % Proctor density. (See diagrams). Non-Drainage (overlay) application using COMPLETE SAND G2. Remove all loose and fragile concrete and compact the substrate. Cover the ground with a Gator Fabric GF 4,4, refill with crushed stone, and compact it. ICPI recommends 2 inches diameter drainage holes spaced approximately 10 feet apart and at the lowest elevations in the concrete slabs. Holes should be filled with #8 stone and covered with a 1 foot x 1 foot patch of Gator Fabric GF 4,4. Drilled holes should allow any water entering the bedding layer to freely flow out (see below the different graphic scenarios 2, 3 and 4 applications). To learn more, visit us online at Polybind.com 59 4 GRID AND FABRIC INSTALLATION EDGES

60 Installation Instructions PREPARATION INFORMATION Important Notes A-1 Drainage Base application, using POLYMERIC SAND, Pavers and slabs must be installed according to ICPI Tech Spec #2 non-overlay ( before COMPLETE POLYMERIC Sand installations. A-2 Non-Drainage (overlay) application using COMPLETE POLYMERIC SAND. Remove all loose and fragile concrete and compact the substrate. Cover the ground with a Gator Fabric GF 4,4, refill with crushed stone, and compact it. ICPI recommends 2 inches diameter drainage holes spaced approximately 10 feet apart and at the lowest elevations in the concrete slabs. Holes should be filled with #8 stone and covered with a 1 foot x 1 foot patch of Gator Fabric GF 4,4. Drilled holes should allow any water entering the bedding layer to freely flow out. B Always refer to the latest POLYMERIC SAND Technical Data Sheet at Polybind.com before installing POLYMERIC SAND. C Pavers sides and top surfaces must be completely dry. Do not apply if the paver surface is damp or wet. The damp or wet surface will cause POLYMERIC SAND to prematurely activate and will lead to the polymers sticking on the paver surface. D Do not apply if the paver joints are damp or wet. This will prevent POLYMERIC SAND BY/PAR ALLIANCE DESIGNER PRODUCTS the POLYMERIC SAND from properly sliding into the joints and obtaining very densely packed joints, which is critical to the product s performance. E-1 Drainage base systems, POLYMERIC SAND, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation). E-2 Non-Drainage base systems (Overlays), Only use COMPLETE SAND, it sets within 24 hours after water activation at above 32ºF (0ºC) (No rain should occur within 24 hrs after water activation). F Avoid excessive watering or flooding of paver surface. G For all paver surfaces, and COMPLETE BY/PAR ALLIANCE DESIGNER PRODUCTS particularly around in-ground pools, there must be a slope of 1/8 inch (3 mm) per linear foot away from the edge of the pool or structures to ensure optimal performance of the POLYMERIC SAND. H For the pool coping units, it is mandatory to use mortar in the joints. For the rest of the paver installation around the pool, you can use POLYMERIC SAND. I Install POLYMERIC SAND a minimum of 1/8 inch (3 mm) below the paver surface or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tires. Joints should be filled up to 1/8 inch (3 mm) below the edge or chamfer. J Do not sweep POLYMERIC SAND over asphalt. GRID AND FABRIC SAND & COMPLETE SAND INSTALLATION STEPS (FOR AN EXISTING PAVER SURFACE) 1 & 2 3 & EDGES INSTALLATION 1 Spread POLYMERIC SAND with hardbristle broom. Make sure the POLYMERIC SAND completely fills the joints. Do not use other materials in the joints. 2 Leave a layer of POLYMERIC SAND on the surface to aid in vibrating and consolidating POLYMERIC SAND into joints. 3 Vibrate the POLYMERIC SAND into the paver joints using a vibratory plate compactor. A protective pad is recommended. A roller compactor is best for slab installation. 4 Joints should be filled up to 1/8 inch below the edge or chamfer. It is best to compact in several directions to ensure there are no air gaps or voids in the joints. Repeat steps 1-3 to ensure joints are filled and consolidated. Narrow joints require more care to completely fill. 5 Sweep off excess POLYMERIC SAND from the paved surface, first with a hard-bristle broom, then a soft bristle broom. Take care to leave the polymeric sand at least 1/8 inch below the edge or chamfer of the paver. 6 Use a leaf blower to remove all remaining POLYMERIC SAND residue from the paved surface. WATER ACTIVATION FOR POLYMERIC SAND Important Notes A Work in manageable sections, ideally about 100 sq. ft. at a time, depending on temperature. To learn more, visit us online at Polybind.com 60 B Do not allow POLYMERIC SAND to wash out of joint. C Never allow paved surface to dry out during the water activation phase. D Watering must be started at the lowest point of the paved surface 100 sq. ft. (9.3 sq. m.) section for 1 minute. E Use a watering gun connected to a hose. Set to shower.

61 BY/PAR ALLIANCE DESIGNER PRODUCTS BY/PAR ALLIANCE DESIGNER PRODUCTS BY/PAR ALLIANCE DESIGNER PRODUCTS COMPLETE FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION USING COMPLETE SAND Non-Drainage (overlay) application using COMPLETE SAND. Remove all loose and fragile concrete and compact the substrate. Cover the ground with a Gator Fabric GF 4,4, refill with crushed stone, and compact it. ICPI recommends 2 inches diameter drainage holes spaced approximately 10 feet apart and at the lowest elevations in the concrete slabs. Holes should be filled with #8 stone and covered with a 1 foot x 1 foot patch of Gator Fabric GF 4,4. Drilled holes should allow any water entering the bedding layer to freely flow out (see below the different graphic scenarios 2, 3 and 4 applications). minimum of 6 inches (15 cm) POLYMERIC SAND COMPLETE FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION USING SAND OR COMPLETE SAND For Drainage Base: SAND is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. The concrete pavers must be installed on a drainage base system composed of 2 layers. The upper layer can have a maximum of 1 inch of bedding sand. The lower layer must have a minimum of 6 inches of crushed stone 0 3/4 (0 20 mm) compacted at 98 % Proctor density. (See diagrams). SAND COMPLETE SAND SAND COMPLETE SAND SAND COVERAGE FOR SAND & COMPLETE SAND 50 lbs (22.7 kg) Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. (JOINT IS COMPLETELY FILLED WITH POLYMERIC SAND) Narrow joints sq ft ( sq m) Nevada Tan & Oxford Grey Wide joints sq ft ( sq m) SAND & COMPLETE SAND WATER ACTIVATION STEPS (FOR AN EXISTING PAVER SURFACE) GRID AND FABRIC 7 7 Shower water on a specific water area of 100 sq. ft., wait no longer than 2 to 3 minutes. Proceed to STEP 8. IMPORTANT The water used in steps 7 to 9 will activate a bonding action as well as condensing POLYMERIC SAND in the joints. It is important to water the POLYMERIC SAND a total of 3 times, as per steps 7, 8 and 9.Too little water will not properly activate the POLYMERIC SAND and will reduce the final performance. If steps 7 to 10 are not done properly, a white haze may appear on paver surface after installation. This is due to excess POLYMERIC SAND residue left on paver surfaces. This haze will dissipate over time, or it could be removed by using efflorescence cleaner. 8 8 Shower and rinse simultaneously on a section of approximately 100 sq. ft. so as to eliminate any POLYMERIC SAND residue left on the pavers. Any POLYMERIC SAND residue should go directly into the paver joints. Wait no longer than 2 to 3 minutes. Proceed to STEP Shower and rinse simultaneously, so as to eliminate any POLYMERIC SAND residue. Any residue should go directly into the paver joints. However, stop showering when you see water retention on the paver joints. Wait no longer than 2 to 3 minutes. Proceed to STEP 10. Note: Repeat the directions of STEPS 7 to 9 for all other areas that have not been showered with water. To learn more, visit us online at Polybind.com Use a leaf blower to remove any excess water remaining on the paver pores and crevices. This blowing action is necessary to help remove any remaining POLYMERIC SAND residue left on paver surfaces from the previous steps. 11 Drainage base systems, POLYMERIC SAND, sets within 1 hour after water activation at above 32ºF (0ºC) (No rain should occur within 1 hour after water activation). POLYMERIC SAND INSTALLATION STEPS FOR AN EXISTING PAVER SURFACE If using POLYMERIC SAND to replace existing jointing materials, old jointing materials need to be completely cleaned out of the joints and pavers completely dry before installing POLYMERIC SAND. However, be careful not to disturb the bedding material under the pavers. Follow steps 1 to 10 of POLYMERIC SAND installation steps (for a new paver surface). INSTALLATION EDGES

62 Installation Instructions PREPARATION INFORMATION Important Notes A must be installed above 59 F (15 C). B can only be installed if rain is not forecasted in the next 24 hours. C Wet cast and natural stone sides and top surfaces must be completely dry. Do not apply if the surface is damp or wet. The damp or wet surface will cause to prematurely activate and INSTALLATION STEPS FOR A NEW SURFACES OF WET CAST AND NATURAL STONES will lead to the polymers sticking on the natural stone or wet cast unit surface. D Do not apply if the natural stone or wet cast unit joints are damp or wet. This will prevent the from properly sliding into the joints and obtaining very densely packed joints, which is critical to the products performance. E Minimize or avoid walking on the stones for 24 hours after the installation of. F If is left lying on the stone surface for a long duration, moisture can form and will activate the on the stone surface, staining may occur. G Do not use when the stones are installed over a concrete base. is designed to function on a drainage base system (see diagram 1 on page 63). A concrete base inhibits drainage, thus the trapped water will negatively impact the product s performance. WATER ACTIVATION STEPS FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION is recommended for a variety of uses, including patios, walkways and pool decks. The stones must be installed on a drainage base system: maximum of 1 (2.5 cm) of bedding sand, plus a minimum of 6 (15 cm) of crushed stone compacted at 98% Proctor density and respecting a minimum slope of 1 degree. GRID AND FABRIC EDGES INSTALLATION 1 1 Install the stones on a maximum 1 bed of sand. Make sure that there is at least 6 of compacted crushed stone under the bedding sand. (See diagram 1.) 2 2 Make sure the stone s top surface and sides are dry. FOR NATURAL STONES Using a hard-bristle, broom, sweep in between the full depth of the natural stone joints. FOR WET CAST STONES Using a scoop, carefully pour in between the full depth of the joints and avoid getting any on the wet cast stone surface. 3 3 Hit the stones with a rubber mallet; this will make the settle firmly into the joints and removing any air pockets. Repeat step 2 and 3 at least two more times. 4 4 Using a soft, fine-bristle broom, sweep all excess off stone surfaces. Ensure that lies at least 1/8 inch below the top of the stones. 5 5 Using a leaf blower, blow all residues off stone surfaces. 6 Shower water on a specific area of 100 sq.ft., wait no longer than 2 to 3 minutes. Proceed to STEP 7. 7 Shower and rinse simultaneously on a section of approximately 100 sq.ft. so as to eliminate any residue left on the stones. Any residue should go directly into the stones joints. Wait no longer than 2 to 3 minutes. Proceed to STEP 8. 8 Shower and rinse simultaneously, so as to eliminate any residue. Any residue should go directly into the stones joints. However, stop showering when you see water retention on the stones joints. Wait no longer than 2 to 3 minutes. Proceed to STEP 9. Note: Repeat the directions of STEPS 6 to 8 for all other areas that have not been showered with water. WATER ACTIVATION Important Notes To learn more, visit us online at Polybind.com Use a leaf blower to remove any excess water remaining on the stones pores and crevices. This blowing action is necessary to help remove any remaining residue left on stones surfaces from the previous steps. IMPORTANT The water used in step 6 will activate a bonding action as well as condensing in the joints. A Work in manageable sections, ideally about 100 sq. ft. at a time, depending on temperature. B Do not allow to wash out of joint. C Never allow paved surface to dry out during the water activation phase. D Watering must be started at the lowest point of the paved surface. E Use a watering gun connected to a hose. Setting should be set to shower. 9

63 PLEASE NOTE becomes very firm but will detach from stone if the crushed stone base has excessive movement. It will also detach from the stone if the stones are oscillating back and forth due to improper installation. By following installation instructions carefully, you will obtain a very hard jointing material. It should be noted that will continue to harden over time. Avoid excessive watering or flooding of stone areas. When installing stones around an underground pool, a slope of 1/8 inch (3 mm) per linear foot (30 cm) away from the pool is mandatory. All stone surfaces must have a drainage slope for the to work at its optimum. For the pool coping blocks, it is mandatory to use mortar in the joints. For the rest of the stone installation around the pool, you can use. Do not sweep over asphalt. COVERAGE The quantity required depends on the shape and size of the stones as well as the width of the joints. One bag of 50 lbs (22.7 kg) of this product will cover between 20 to 30 sq ft (1.86 to 2.79 sq m) if the joints are about 1 to 2 (2.54 to 5.08 cm) wide and the stones are about 2 to 2-1/2 (5.08 cm to 6.35 cm) thick. will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product. COVERAGE PER BAG 50 lbs (22.7 kg) The quantity required depends on the shape and size of the stones as well as the width of the joints. Joints are about 1 to 2 (2.54 to 5.08 cm) wide and the stones are about 2 to 2-1/2 (5.08 cm to 6.35 cm) thick. FABRIC FABRIC 20 to 30 sq ft (1.86 to 2.79 sq m) (JOINT IS COMPLETELY FILLED WITH ) (JOINT DILUTED WITH OTHER PRODUCT) GRID AND FABRIC To learn more, visit us online at Polybind.com 63 INSTALLATION EDGES

64 Installation Instructions STEP 1 Excavation of the new Gator Tile area STEP 3 Addition of Gator Fabric GF 4.4, levelling and compacted bedding sand STEP 4 installation of the Gator Base STEP 6 Installation of Gator Tile Edge and Gator Base Screws GRID AND FABRIC Excavate the new Gator Tile area. The depth required is calculated by adding Porcelain Tile height, Gator Base, bedding sand, plus any soft organic material that has to be removed. Excavate the perimeter an extra 6 (15 cm) wider on all sides than the finished tile area requires. STEP 2 Levelling and compacting of the base 1 3A A Lay down a non-woven Gator Fabric GF 4.4 geotextile (minimum 100 LBF) and cover the entire excavated area. Make sure to install the Gator Base on the extended excavation area (total excavation should be 6 [15 cm] wider on each side than the final tiled area. Start laying the Gator Base units ensuring Gator Base interlocks with the tongue & groove system. STEP 5 Installation of porcelain tile and Gator Spacer 5 4 Install Gator Tile Edge on the Gator Base using Gator Base Screws, make sure that Gator Tile Edge rests firmly against the tiles. Use Gator Base Screws at every second hole. STEP 7 Sweeping, compacting and blowing of the Gator Tile Sand 6 When using Gator Tile Sand, porcelain tiles must be installed on a Gator Base foundation using the Gator Tile Systems. EDGES INSTALLATION 2A A Ensure a slope of at least 1 degree away from any structure, such as a house. 2B B The native soil needs to be compacted using a plate compactor or hand tamper. 3B B Spread an even layer of sand, no more than 3/4 thick (19 mm). Levelling and compacting the bedding sand will be the last step prior to installing the Gator Base. 3C C Water the sand prior to using a hand compactor and/or plate compactor, compacting the 3/4 (19 mm) layer of bedding sand until you obtain a final height of 1/2 (13 mm) of compacted bedding sand. This compacted surface should reflect the final tiled surface. Gator Spacers should receive a generous amount of Polybind XTRA polyurethane glue on each quadrant. Install the Porcelain Tile on the Gator Spacer, apply pressure or tap the tiles with a rubber mallet at all corners. This will ensure that the tiles are adhering to the Gator Spacer. The Gator Spacer will be left in the tile installation permanently, ensuring proper alignment and stability of your project for years to come. N.B. Gator Spacers are offered in 1/4, 3/16 and 1/8 (6.4 mm, 4.8 mm and 3.2 mm) joint sizes. To learn more, visit us online at Polybind.com 64 7A A When emptying the bag of TILE SAND, spread it onto the dry, tiled surface. When sweeping the TILE SAND, spread it over a small area before moving onto the next, while making sure to fill in the joints.

65 B It is now time to compact the sand into the joints using a rubber mallet. Do not use a plate compactor. Repeat filling and compacting of the tile joints. Finally, sweep the surface with a fine bristle broom and remove all excess sand. Ensure the sand is 1/8 (3 mm) lower than the tile chamfers. C Finally, use a blower to blow off all sand residue laying on the tile surface. TILE SAND INFORMATION Moss 7B 7C TILE SAND will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product. STEP 8 Gator Tile Sand water activation steps 8A-B-C A Shower water on a specific area of 100 sq.ft., wait no longer than 2 to 3 minutes. B Shower and rinse simultaneously on a section of approximately 100 sq. ft. so as to eliminate any TILE SAND residue left on the tiles. Wait no longer than 2 to 3 minutes. C Shower and rinse simultaneously, so as to eliminate any TILE SAND residue. Any residue should go directly into the tiled joints. However, stop showering when you see water retention on the tiled joints. Wait no longer than 2 to 3 minutes. Note: Repeat the directions of STEPS 8a, 8b and 8c for all other areas that have not been showered with water. WATER ACTIVATION Important Notes A1 Work in manageable sections, ideally about 100 sq. ft. at a time, depending on temperature. B1 Do not allow TILE SAND to wash out of joint. C1 Never allow tiled surface to dry out during the water activation phase. D1 Watering must be started at the lowest point of the tiled surface. E1 Use a watering gun connected to a hose. Setting should be set to shower. IMPORTANT For use on and required sub-surface preparation TILE SAND is recommended for a variety of pedestrian uses including pool decks, patios, footpaths etc. The Gator Tile Sand should only be installed when using the Gator Base as shown below. Must use all the components of the Gator Tile System (Refer to page 28) To learn more, visit us online at Polybind.com 65 8D D Use a leaf blower to remove any excess water remaining on the tiled crevices. This blowing action is necessary to help remove any remaining TILE SAND residue left on tiled surfaces from the previous steps. The water used in steps 8a, 8b and 8c will activate a bonding action as well as condensing TILE SAND in the joints. It is important to water the TILE SAND a total of 3 times, as per steps 8a, 8b and 8c. Too little water will not properly activate the TILE SAND and will reduce the final performance. SAND COVERAGE 35 lbs (15.9 kg) Quantity required depends on the shape and size of the porcelain tiles. 24" x 24" Tile with 1/8" (3.2 mm) joints Beige, Slate Grey & Ivory 220 sq ft (20.4 sq m) Black Diamond 190 sq ft (17.7 sq m) 24" x 24" Tile with 3/16" (4.8 mm) joints Beige, Slate Grey & Ivory 170 sq ft (15.8 sq m) Black Diamond 150 sq ft (13.9 sq m) 24" x 24" Tile with 1/4" (6.4 mm) joints Beige, Slate Grey & Ivory 125 sq ft (11.6 sq m) Black Diamond 110 sq ft (10.2 sq m) GRID AND FABRIC INSTALLATION EDGES

66 Installation Instructions Under License from Brock International-Patented and Patents Pending: Please follow ICPI Tech Specs 2 for compaction guidelines STEP 1 Excavation of the new Gator Base area STEP 4 Installation of the Gator Base GRID AND FABRIC Total excavation will be done as follows. 1 Total depth will be determined by adding the following elements depths: Gator Fabric GF 4.4, compacted bedding sand s final height (1/2 [13 mm]), Gator Base (3/4 [19 mm]), and paver s height. Total excavation width should be 6 (15 cm) wider on each side than the final paved area. This excavation could be done using a shovel or excavator. Prior to excavating, check with local utility services to ensure digging does not damage underground pipes or wires. 2B B The native soil needs to be prepared and compacted in the same way that one would prepare a traditional base installation, using a hand tamper or plate compactor. This area should be as smooth as possible to get rid of high or low spots within about 3/8 (10 mm). Using a string level (stakes and a string line), tie the string to the stakes to establish level according to which the final slope will be measured (minimum of 1 degree to the desired final paver level). Once the final level is achieved, proceed to step 3. STEP 3 Addition of Gator Fabric GF 4.4, levelling and compacted bedding sand 3B B Spread an even layer of sand to a depth of 3/4 (19 mm) over the Gator Fabric GF 4.4. To obtain a perfect 3/4 (19 mm) bedding layer, use two 3/4 (19 mm) pipes with an equal distance of 4 to 6 ft (1.22 to 1.83 m) over the Gator Fabric GF 4.4 and fill the surrounding area with sand. Using a straight board, level the bedding sand relatively to the pipes. When removing the pipes, fill in the empty gaps. Remember that levelling and compacting the bedding sand will be the last step prior to installing the Gator Base. 3C Make sure to install the Gator Base on the extended excavation area (total excavation should be 6 [15 cm] wider on each side than the final paved area). Start laying the Gator Base units while ensuring locking of the tongue & groove system. This will guarantee the panels stability when the pavers or slabs are laid down. Trim any visible curves or protruding angles using a utility knife. STEP 5 Installation of pavers and Polybind Edge 4 EDGES STEP 2 Levelling and compacting of the base 2A A Once excavation is completed, level the excavated area using a rake or shovel. Ensure a slope of at least 1 degree away from any structure, such as a house. 3A A Lay down the Gator Fabric GF 4.4 and cover the complete excavated area. C Using a hand compactor and/or plate compactor, compact the 3/4 (19 mm) of bedding sand until you obtain a final height of ½ (13 mm) of compacted bedding sand. The final area should be smooth. 5 Lay the pavers directly onto the Gator Base according to the selected pattern. (Adding a second layer ½ (13 mm) of loose bedding sand on top of the Gator Base is also an accepted method of installation.) Use a rubber mallet to adjust the pavers. Make sure the Gator Base is 6 (15 cm) wider on each side than the paved surface. Install Polybind Edge on the Gator Base, making sure it rests firmly against the pavers. A Gator Base Screw will be driven into every second hole to maximize lateral support of the Polybind Edge. INSTALLATION To learn more, visit us online at Polybind.com 66

67 STEP 6 Sweeping, compacting and blowing of the Polybind Complete polymeric sand 6A A When emptying the Polybind Complete polymeric sand bag, spread it onto the dry paved surface. This will avoid segregation and sweeping a mountain of sand. When sweeping the polymeric sand, spread over a small area before moving onto the next, while making sure to fill in the joints. IF USING COMPLETE G2 FOLLOW THESE INFORMATION: B It is now time to compact the sand into the joints using a hand tamper or plate compactor. Do not use a plate compactor over slabs. Repeat filling and compacting of the paver joints. Finally, sweep the surface with a fine bristle broom and remove all excess sand. Ensure the sand is 1/8 (3 mm) lower than the paver chamfers. When laying different thickness of pavers or stones, adding a second layer 1/2 (13 mm) of loose bedding sand on top of the Gator Base is also an accepted method of installation. Visit our website for any updated instructions and or TDS. 6B Activate COMPLETE G2 by showering 50 sq. ft. (4,5 sq. m.) section for 1 minute, starting at the lowest point. Once all the sections are activated, rinse off any debris that is on the total paver surface. If using COMPLETE continue step 6C and 7A, B and C. PAVER C Finally, use a blower to blow off all sand residue lying on the paved surface. The combined actions of the sweeping and blowing will help eliminate any hazing effect. STEP 7 Watering and blowing action The watering process will activate the polymeric sand s bonding process, and the sand will harden when dry. WAY COMPACTED BEDDING SAND 1/2 FABRIC GF4.4 COMPACTED NATIVE SOIL NO CRUSHED STONE EQUIVALENT (=) To learn more, visit us online at Polybind.com 67 6C 7A-B PAVER A Set your water spray to shower and spray the paved surface for 10 to 15 seconds, then wait 3 to 4 minutes. (N.B. Ensure the paved surface does not dry between waterings). B Shower and rinse the paved surface and wait 3 to 4 minutes before repeating the shower and rinse process for a third and final time. However, stop watering when you see a minimal amount of water retention on the paver joints. If the work is being done on a hot summer day, avoid spraying large areas, as they will dry up faster. C Finally, use a blower to remove any excess water remaining on the paver surface. Please visit our web site at AllianceGator.com for other applications such as natural stones. TRADITIONAL WAY BEDDING SAND 1/2 FABRIC GF4.4 6 INCHES OF CRUSHED STONE COMPACTED NATIVE SOIL 7C GRID AND FABRIC INSTALLATION EDGES

68 Application Instructions SHAMPOO Instructions 1 Wet paver surface with water. 2 Dip a hard bristle brush in a pail containing the mixed product, or with the help of a sprayer, apply the Polybind Shampoo on the paver surface and scrub. 1 U.S. gal. (3.78 L.) of diluted product is to be used for every 75 sq. ft. (7 sq. m.) of paver surface. 3 Rinse thoroughly with water and move on to the next section of 75 sq. ft. (7 sq. m.). 4 Repeat steps 2 & 3 over all the sections in question. 5 Once the surface is clean, use water hose and generously rinse off Polybind Shampoo until there is no more foaming action on the pavers. Please note 1 This product is not an efflorescence cleaner. 2 Do not let product dry on surface. 3 Wear goggles and rubber gloves. 4 ALWAYS TEST the product on a small hidden area of approximately 4 sq.ft. (0.4 sq. m.) to ensure the results meet your expectations. 5 Mix 1 part Polybind Shampoo in 4 parts water, any concentration greater than this can discolor the pavers. 6 Do not apply under hot sun. 7 Keep paver surface wet from start to finish. 8 Repeat steps if there is a lot of dirt trapped in the pavers and natural stones. Ideal Mixture 4 parts water, 1 part product. GRID AND FABRIC EFFLORESCENCE CLEANER Instructions 1 Wet paver surface with water. 2 Use a pump sprayer or watering can to apply the diluted product on the wet paver surface. Wait one minute for product to react then scrub the surface vigorously using a hard bristle brush. 1 U.S. gal. (3.78 L.) of diluted product is to be used for every 40 sq. ft. (3.7 sq. m.) of paver surface. 3 Rinse thoroughly with water and move on to the next section of 40 sq ft (3.7 sq m). 4 Repeat steps 2 & 3 over all the sections in question. 5 Once the surface is clean, use water hose and generously rinse off Polybind Efflorescence Cleaner until there is no more foaming action on the pavers. Please note 1 Polybind Efflorescence Cleaner should be used prior to applying a sealer to ensure a proper sealer adhesion. 2 Freshly installed Polybind Polymeric Sand must be allowed to cure for 48 hours at a temperature above 59 F (15 C) and under no rain before using Polybind Efflorescence Cleaner. 3 Do not let product dry on paver surface. Keep paver surface wet from start to finish. 4 Wear goggles and rubber gloves. 5 Never use on new concrete pavers. Wait at least 60 days after new pavers are installed before using this product. 6 ALWAYS TEST the product on a small hidden area of approximately 4 sq ft (0.4 sq m) to ensure the results meet your expectations. Do not apply under extremely strong sun. 7 Dilute 1 part Polybind Efflorescence Cleaner in 4 parts water, any concentration greater than this can discolor the pavers 8 You might have to repeat this process if there is a lot of efflorescence trapped in the pavers. Ideal Mixture 4 parts water, 1 part product. EDGES INSTALLATION EFFLORESCENCE & SLURRY REMOVER Instructions 1 Wet paver surface with water. 2 Use a pump sprayer or watering can to apply the diluted product on the wet paver surface. Wait one minute for product to react then scrub the surface vigorously using a hard bristle brush. 1 U.S. gal. (3.78 L.) of diluted product is to be used for every 40 sq. ft. (3.7 sq. m.) of paver surface. 3 Rinse thoroughly with water and move on to the next section of 40 sq ft (3.7 sq m). 4 Repeat steps 2 & 3 over all the sections in question. 5 Once the surface is clean, use water hose and generously rinse off EFFLORESCENCE & SLURRY REMOVER until there is no more foaming action on the pavers. Please note 1 EFFLORESCENCE & SLURRY REMOVER should be used prior to applying a sealer to ensure a proper sealer adhesion. 2 Freshly installed Polybind Polymeric Sand must be allowed to cure for 48 hours at a temperature above 59 F (15 C) and under no rain before using EFFLORESCENCE & SLURRY REMOVER. 3 Do not let product dry on paver surface. Keep paver surface wet from start to finish. 4 Wear goggles and rubber gloves. 5 Never use on new concrete pavers. To learn more, visit us online at Polybind.com 68 Wait at least 60 days after new pavers are installed before using this product. 6 ALWAYS TEST the product on a small hidden area of approximately 4 sq ft (0.4 sq m) to ensure the results meet your expectations. Do not apply under extremely strong sun. 7 Dilute 1 part EFFLORESCENCE & SLURRY REMOVER in 8 parts water, any concentration greater than this can discolor the pavers. 8 You might have to repeat this process if there is a lot of efflorescence trapped in the pavers. Ideal Mixture 8 parts water, 1 part product.

69 X-TRA OIL AND GREASE REMOVER Instructions Do not use on wet surfaces. Use at a temperature above 40 F (4 C) and provide maximum ventilation. 1 Shake bottle before applying to stain, extending one inch beyond perimeter of the stain. 2 Allow to dry completely to powder (12 to 24 hours. This depends on temperature, humidity, and ventilation). 3 Sweep product up. If area still appears dark, provide adequate ventilation and allow moisture to evaporate. 4 If stain remains, re-apply, scrub with hard-bristled brush, and repeat steps 2 and 3. 5 May need to rinse residue. Please note Before use on sealed, colored, or painted surfaces, ALWAYS TEST the product on a small hidden area of approximately 4 sq in (26.4 sq cm) to ensure the results meet your expectations. Prior use of other cleaners may inhibit performance. If applied on sealed pavers product may damage the sealer. Not recommended for synthetic oil stains. RUST REMOVER Instructions Please note 1 Apply product on stain. 2 Let product soak for 2-3 minutes. 3 Scrub with a hard bristle-brush. 4 Rinse thoroughly with water. 5 Repeat steps 1 to 4 until the stain dissolves. 1 Do not let product dry on paver surface. 2 Wear goggles and rubber gloves. 3 After using the Polybind Rust Remover on various spots, clean the entire paver surface with Polybind Efflorescence Cleaner for an overall uniform color. RUBBER, PAINT & TAR REMOVER + Instructions 1 Apply product on stain. 4 Please store container at a temperature above 32 F (0 C). Please note 1 This product dissolves sealants. GRID AND FABRIC SEALER STRIPPER 2 Let it soak for 5 minutes. 3 Apply product again. 4 Immediately scrub with hard bristle brush. 5 Repeat steps 3 & 4 until stain dissolves. 6 Rinse thoroughly with water. Preparation 1 Surface must be clean and dry. 2 Wet down all vegetation before starting work. 3 Protect and cover all areas such as vegetation 4 Solvent resistant polyethylene sheets can be used as an effective barrier. 5 For best results, use above 50 and below 90 F (32 C). 6 If products dries or hardens to surface, apply a thin coat of Sealer Stripper on hardened area and wait 30 to 60 minutes and remove. 2 Do not let product dry up on paver surface. 3 Wear goggles and rubber gloves. 4 Use at above 60 F (16 C) in dry conditions. Application 1 Always work in smaller manageable areas when stripping 2 Use a brush or roller apply paste no less than a 1/8 (3.2 mm) thick 3 On irregular surfaces use a nylon brush to force paste into intricate areas 4 Reaction time between 3 24 hours if necessary 5 Average spread rate of approximately sq. ft. (3.7 sq. m sq. m.) per gallon; results may vary based on surfaces texture and porosity. To learn more, visit us online at Polybind.com 69 Removal & Clean up 1 Use a pressure washer 2 Immediately use a nylon brush and clean water to scrub residue off the surfaces 3 Rinse thoroughly with water to remove all remaining residue 4 For optimal results, low pressure washing is recommended for final rinse 5 Dispose of dissolved coatings according to federal, state and local regulations. INSTALLATION EDGES

70 Application Instructions ECO SEAL HIGH GLOSS +COLOR ENHANCER ECO SEAL HIGH GLOSS ECO SEAL ZERO GLOSS 4 Do not apply if rain is expected within 24 hours. 5 Do not allow sealer to puddle. 6 Temperature should be between 40 F (5 C) and 85 F (29 C) when sealer is applied. 7 Concrete paver surface must be cool to the touch when sealer is applied (between 40 F (5 C) and 85 F (29 C)). 8 Polybind Eco Seal is water repellant, rain safe, after 24 hours. 9 Let the sealer dry for 24 hours before using the sealed area. GRID AND FABRIC ECO SEAL LOW GLOSS +COLOR ENHANCER ECO SEAL LOW GLOSS Please note 1 Use only on Dry Cast concrete pavers and can only be sealed 60 days after their installation date. Consult concrete paver manufacturer s for their recommendation. 2 ALWAYS TEST the product on a small hidden area of approximately 4 sq ft (0.4 sq m) to ensure the results will meet your expectations. 3 Clean the entire surface with the Polybind Clean Efflorescence Cleaner. This product will remove the efflorescence trapped in the concrete paver pores, as well as thoroughly clean the surface for proper sealer adhesion. 10 Wear protective gloves, eye protection and respiratory protection. Options for Using ECO SEAL 1 Can be used as a stand alone sealer. Apply at the rate of 200 sq. ft. (18.5 sq. m.) per gallon. Spray on the surface and back roll if needed to even out the surface. Coverage surface will vary also based on porosity of pavers and joint width. 2 Can be used as a Sealer/Joint Sand Stabilizer w/ ASTM C144 Sand. Apply at the rate of 100 sq. ft. (9.3 sq. m.) per gallon, then force the excess sealer from the surface into the joints using a squeegee or roller. EDGES INSTALLATION WET LOOK HIGH GLOSS SATIN LOOK LOW GLOSS Please note 1 Use only on Dry Cast concrete pavers and can only be sealed 60 days after their installation date. Consult concrete paver manufacturer s for their recommendation. 2 Concrete pavers and jointing sand MUST be 100% dry. 3 Temperature should be between 60 F (16 C) and 85 F (29 C) when sealer is applied. 4 Concrete paver surface must be cool to the touch when sealer is applied (between 60 F (16 C) and 85 F (29 C)). 5 First clean concrete pavers with Polybind Clean products. Remove all oil, grease and rust stains. 6 Use Polybind Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion. 7 Use just one (1) layer of sealer. 8 When using Polybind Seal Wet Look Sealer, assure yourself at least 48 hours of dry conditions prior to applying the sealer. 9 Specifically formulated to be used on unsealed surfaces only. Cannot be used as a resealer. 10 Wear protective gloves, eye protection and respiratory protection. Application instructions 1 ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations. 2 Remove all the stains from the concrete pavers, using Polybind Clean products. Use Gator Clean Sealer Stripper to remove any unknown coating that remains on the concrete paver surface. 3 Remove, if necessary, all contaminated jointing material and replace with Polybind Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation. 4 Wait at least 48 hours at a minimum temperature of 60 F (16 C) and no rain for the Polybind Polymeric Sand to properly harden. 5 Clean the entire surface with the Polybind Efflorescence Cleaner. This To learn more, visit us online at Polybind.com 70 product will remove the efflorescence trapped in the concrete paver pores as well as thoroughly clean the surface for proper sealer adhesion. 6 Wait at least 48 hours at a minimum temperature of 60 F (16 C) and no rain so the sand & concrete paver surface are dry. 7 Best Practice: (See online video. 2 people needed.) Apply one (1) coat of Polybind Wet or Satin Look Sealer using a sprayer in 60 sq. ft. sections, then use a solvent-resistant foam roller to remove the excess sealer left on the surface. 8 Polybind Satin & Wet Look Sealer are water repellant, rain safe, after 90 min and could be used as a joint stabilizer. 9 Let the sealer dry for 24 hours before using the sealed area. Coverage Can be use as a stand alone sealer. Can be apply at 175 sq.ft. per gallon. Spray and back roll to even out the surface. Coverage surface will vary also based on porosity of pavers and joint width.

71 RESEALER Please note 1 Concrete pavers should only be sealed 60 days after their installation date. Consult concrete paver manufacturer s for their recommendation. STONE BOND XP Instructions 1 Aggregate selection for final surface Select an aggregate that contains a variety of sizes. For instance, crushed stone mixes such as 3/8 minus, 1/4 minus or 3/16 minus work well with Gator Stone Bond, where as single-size aggregates like 3/8 rock or pea gravel ROCK BOND 2 Concrete pavers & jointing sand MUST be 100% dry. 3 Temperature should be between 60 F / 16 C to 85 F / 29 C when sealer is applied. 4 Concrete paver surface temperature should be between 60 F / 16 C to 85 F / 29 C and concrete paver surface must be cool to the touch when sealer is applied. 5 Use Polybind Efflorescence Cleaner to remove ground in dirt from the surface of concrete pavers. It will make the concrete pavers look clean and vibrant. Applying Polybind Efflorescence Cleaner before a Polybind Resealer application will assure you of a deeper penetration into the cleaned surface. are not suitable. Screenings with extremely high fine content are not suitable either. To ensure compatibility of the selected aggregate with Gator Stone Bond, prepare a test area. 2 Structural Stone Base preparation Before starting the actual project, factors such as climate, native soil type and amount of use should be taken into consideration. As a rule of thumb, "the better the base preparation, the better the results." Option 1 For optimum performance, install 4 to 6 in. (10 to 15 cm) of 3/4 minus crushed stone, then compact using a vibratory plate compactor. Option 2 Install 2 to 4 in. (5 to 10 cm) of 3/4 minus, 3/8 minus, 1/4 minus or 3/16 minus, then compact using a vibratory plate compactor. In restricted areas where a compactor will not fit, use a hand tamper. 3 Surface Aggregate Spread a maximum of 1" (2.5 cm) in Application instructions Please note Wear gloves to avoid having binder sticking on your hands. Products should be mixed in a masonry mixer or in a wheelbarrow or on a plywood board. 1 Prepare a solid base by densely compacting 4 (10 cm) of crushed stones. 2 Mix one 1/2 quart (473 ml) container of Gator Rock Bond with 100% dry clean riverstone (40 lb / 18.2 kg) provided for 4 minutes. 3 Trowel the mixed riverstone on the surface desired, within 20 minutes after mixing. 6 Just use 1 layer of Polybind Resealer. 7 When using Polybind Resealer assure yourself at least 48 hours of dry conditions prior to applying Polybind Resealer. If temperature is above 60 F / 15 C the surface should dry within hours. 8 Wear protective gloves, eye protection and respiratory protection. Application instructions 1 ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations. 2 Before commencing the project ensure that there is no rain forecasted for the next 24 hours. surface aggregate over the compacted structural stone base. Rake or screed to the desired level, a minimum of 2 degree slope to allow water run-off. Do not compact until after Gator Stone Bond has been applied. 4 Apply the Gatore Stone Bond Using a watering can or pump sprayer, apply the Gator Stone Bond to the surface at the rate of 15 sq. ft (1.4 sq. m.) per gallon for residential pedestrian use, or 10 sq. ft. (0.9 sq. m.) per gallon for commercial pedestrian use. Allow Gator Stone Bond to fully penetrate through the material. 5 Compaction While surface is still damp but not saturated, compact the surface with a vibratory plate compactor; 2 or 3 passes are recommended. In restricted areas where a compactor will not fit, use a hand tamper. The better the compaction, the better the results. Application Instructions when using Gator Rock Bond binder only Types of rock that can be used: GRANITE LIMESTONE MARBLE 1/8 to 3/8 (3 mm to 10 mm) these rocks have to be clean, free of dust & 100% dry. Method of application of Gator Rock Bond 1 Prepare a solid base by densely compacting 4 (10 cm) of crushed stones. 2 Mix in a ratio of one container (1 US gal. / 3.78L) of ROCK BOND with (320 lbs / 145 kg) the above mentioned dry clean stones for 4 minutes. Mix products automatically with a masonry mixer To learn more, visit us online at Polybind.com 71 3 First clean concrete pavers with Polybind Clean products. Remove all oil, grease and rust stains. Use Polybind Efflorescence Cleaner to thoroughly clean the surface to ensure a proper Polybind Resealer adhesion. 4 Wait at least 48 hours at a minimum temperature of 60 F / 15 C and no rain so the Polybind Polymeric sand & concrete paver surface are dry. 5 Apply coat of Polybind Resealer using a foam roller. 6 Polybind Resealer is water repellant, rain safe, after 90 min. 7 Let it dry for 24 hours before using the sealed area. Instructions for rebuilding an existing surface 1 Scarify or rototill at least 1 in. (2.5 cm) of the surface, break up any clumps, making any necessary repairs, and add new surface aggregate as needed. 2 Apply Gator Stone Bond at the rate of 15 sq. ft (0.5 sq. m.) per gallon; allow liquid to penetrate. 3 Compact using a vibratory plate compactor. In restricted areas where a compactor will not fit, use a hand tamper. Instructions for maintaining an existing surface 1 Make repairs as needed. 2 Apply Gator Stone Bond at the rate of 20 to 45 sq. ft (1.9 to 4.2 sq. m.) per gallon. Some judgement will be needed, as consideration for absorption and desired results should be taken into account. 3 Compact any loose areas. or you can manually mix on a sheet of plywood or in a wheel barrow. 3 Trowel the mixed riverstone on the surface desired, within 20 minutes after mixing. Please note For pedestrian use only. Works above 60 F (16 C). Allow 24 hours to dry without rain. All tools used could be cleaned using Gatorene. Gator Rock Bond has a high gloss appearance when first applied, the shine will gradually diminish within 3 months. This will not affect the bonding of the stones. GRID AND FABRIC INSTALLATION EDGES

72 Application Instructions SERIES GRID AND FABRIC WET CAST LOW GLOSS +COLOR ENHANCER Please note 1 DELUXE SERIES WET CAST SEALER for Wet Cast products should only be sealed 60 days after their installation date. Consult Wet Cast product manufacturer s for their recommendation. 2 Wet Cast products and jointing sand MUST be 100% dry. 3 Temperature should be between 60 F (16 C) and 85 F (29 C) when sealer is applied. 4 Wet Cast product surface must be cool to the touch when sealer is applied (between 60 F (16 C) and 85 F (29 C)). 5 First clean Wet Cast products with Polybind Clean products. Remove all oil, grease and rust stains. 6 Use Polybind Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion. 7 Use just one (1) layer of sealer. 8 When using DELUXE SERIES WET CAST SEALER, assure yourself at least 48 hours of dry conditions prior to applying the sealer. 9 Specifically formulated to be used on unsealed surfaces only. Cannot be used as a resealer. 10 Wear protective gloves, eye protection and respiratory protection. Application instructions 1 ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectation. 2 Remove all the stains from the Wet Cast products, using Polybind Clean products. Use Gator Clean Sealer Stripper to remove any unknown coating that remains on the surface of Wet Cast products. 3 Remove, if necessary all contaminated jointing material and replace with Polybind Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation. 4 Wait at least 48 hours at a minimum temperature of 60 F (16 C) and no rain for the Polybind Polymeric Sand to properly harden. 5 Clean the entire surface with the Polybind Efflorescence Cleaner. This product will remove the efflorescence trapped in the Wet Cast product pores as well as thoroughly clean the surface for proper sealer adhesion. 6 Wait at least 48 hours at a minimum temperature of 60 F (16 C) and no rain so the sand & Wet Cast product surface are dry. 7 Best Practice: (See online video. 2 people needed.) Apply one (1) coat of Polybind Seal using a sprayer in 60 sq. ft. sections, then use a solventresistant foam roller to remove the excess sealer left on the surface. 8 DELUXE SERIES WET CAST SEALER is water repellant, rain safe, after 90 min and could be used as a joint stabilizer. 9 Let the sealer dry for 24 hours before using the sealed area. EDGES INSTALLATION WET CAST NATURAL LOOK FINISH, ZERO GLOSS Please note 1 Wet cast products should only be sealed 60 days after their installation date. Consult Wet cast products manufacturer s for their recommendation. 2 Wet cast products and jointing sand MUST be 100% dry. 3 Temperature should be between 32 F (0 C) and 85 F (29 C) when sealer is applied. 4 Wet cast product surface must be cool to the touch when sealer is applied (between 32 F (0 C) and 85 F (29 C)). 5 First clean Wet cast products with Polybind Clean products. Remove all oil, grease and rust stains. 6 Use Polybind Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion. 7 Use just one (1) layer of sealer. 8 DELUXE SERIES WET CAST SEALER can be applied on dry or damp surfaces. 9 Specifically formulated to be used on unsealed surfaces only. Cannot be used as a resealer. 10 Wear protective gloves, eye protection and respiratory protection. Application instructions 1 ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations. 2 Remove all the stains from the Wet cast products, using Polybind Clean products. Use Gator Clean Sealer Stripper to remove any unknown coating that remains on the Wet cast product surface. 3 Remove, if necessary, all contaminated jointing material and replace with Polybind Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation. 4 Wait at least 48 hours at a minimum temperature of 32 F (0 C) and no rain for the Polybind Polymeric Sand to properly harden. 5 Clean the entire surface with the Polybind Efflorescence Cleaner. This product will remove the efflorescence To learn more, visit us online at Polybind.com 72 trapped in the Wet cast product pores as well as thoroughly clean the surface for proper sealer adhesion. 6 Wait at least 48 hours at a minimum temperature of 32 F (0 C) and no rain so the sand & Wet cast product surface are dry. 7 Best Practice: (See online video. 2 people needed.) Apply one (1) coat of DELUXE SERIES WET CAST SEALER using a sprayer in 60 sq. ft. sections, then use a solvent-resistant foam roller to remove the excess sealer left on the surface. 8 DELUXE SERIES WET CAST SEALER is water repellant, rain safe, after 90 min. 9 Let the sealer dry for 24 hours before using the sealed area.

73 DELUXE SERIES NATURAL STONE ZERO GLOSS +COLOR ENHANCER 5 First clean natural stones with Polybind Clean products. Remove all oil, grease and rust stains. 6 Use Polybind Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion. chemicals. Do not dilute. Not for food handling surfaces. Not for glazed tile or non-porous surfaces. Apply between F. Dry residue after a long period may be removed by adding more sealer or mechanically. Application instructions trapped in the natural stone pores as well as thoroughly clean the surface for proper sealer adhesion. 6 Wait at least 48 hours at a minimum temperature of 40 F (4 C) and no rain so the sand & natural stone surface are dry. Please note 1 Natural stones should only be sealed 60 days after their installation date. Consult natural stone manufacturer s for their recommendation. 2 Natural stones and jointing sand MUST be 100% dry. 3 Temperature should be between 40 F (4 C) and 85 F (29 C) when sealer is applied. 4 Natural stone surface must be cool to the touch when sealer is applied (between 40 F (4 C) and 85 F (29 C)). 7 Use just one (1) layer of sealer. 8 When using DELUXE SERIES NATURAL STONE SEALER, assure yourself at least 48 hours of dry conditions prior to applying the sealer. 9 Specifically formulated to be used on unsealed surfaces only. Cannot be used as a resealer. 10 Wear protective gloves, eye protection and respiratory protection. 11 Always keep surfaces dry and clean to reduce slip-fall accidents. This sealer is not anti-slip. Precautions should be taken around pools and showers. 12 Do not let it dry (white film or slippery residue may form). If not wiped dry after 5-10 minutes, residue may form. Do not pressure-wash. Not resistant from acids or caustic 1 ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations. 2 Remove all the stains from the natural stones, using Polybind Clean products. Use Gator Clean Sealer Stripper to remove any unknown coating that remains on the natural stone surface. 3 Remove all contaminated jointing material and replace with Polybind Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation. 4 Wait at least 48 hours at a minimum temperature of 40 F (4 C) and no rain for the Polybind Polymeric Sand to properly harden. 5 Clean the entire surface with the Polybind Efflorescence Cleaner. This product will remove the efflorescence 7 Dry surface for hrs prior to apply sealer. Apply one (1) coat of DELUXE SERIES NATURAL STONE SEALER using a sprayer (HVLP), nap roller (5-10 mm), squeegee, sponge or rag. Apply in 60 sq. ft. (5.6 sq. m.) sections at a time. Use a foam roller or squeegee to remove excess sealer from the surface. Allow remaining sealer to penetrate 5-10 minutes. Wipe and remove any excess sealer with clean, dry, lint-free cotton cloths. Repeat after 30 minutes if not well sealed (make the test with a drop of water). 8 DELUXE SERIES NATURAL STONE SEALER is water repellant, rain safe, after 24 hours. 9 Let the sealer dry for 8hrs for foot traffic (keep surface dry). Full cure after 72 hrs. GRID AND FABRIC NATURAL LOOK, NATURAL LOOK FINISH, ZERO GLOSS MULTI-PURPOSE Please note 1 Natural stones, concrete pavers, retaining wall or masonry units should only be sealed 60 days after their installation date. Consult concrete paver manufacturer s for their recommendation. 2 Concrete pavers, natural stones, retaining wall or masonry units and jointing sand MUST be 100% dry. 3 Temperature should be between 32 F (0 C) and 85 F (29 C) when sealer is applied. 4 Natural stones, concrete paver, retaining wall or masonry units surfaces surface must be cool to the touch when sealer is applied (between 32 F (0 C) and 85 F (29 C)). 5 First clean concrete pavers, natural stones, retaining wall or masonry units with Polybind Clean products. Remove all oil, grease and rust stains. 6 Use Polybind Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion. 7 Use just one (1) layer of sealer. 8 DELUXE SERIES NATURAL LOOK SEALER can be applied on dry or damp surfaces. 9 Specifically formulated to be used on unsealed surfaces only. Cannot be used as a resealer. 10 Wear protective gloves, eye protection and respiratory protection. Application instructions 1 ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations. 2 Remove all the stains from the concrete pavers, using Polybind Clean products. Use Gator Clean Sealer Stripper to remove any unknown coating that remains on the concrete paver surface. 3 Remove, if necessary, all contaminated jointing material and replace with Polybind Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation. 4 Wait at least 48 hours at a minimum temperature of 32 F (0 C) and no rain for the Polybind Polymeric Sand to properly harden. 5 Clean the entire surface with the Polybind Efflorescence Cleaner. This product will remove the efflorescence trapped in the concrete paver, natural stones, retaining wall or masonry units surfaces pores as well To learn more, visit us online at Polybind.com 73 as thoroughly clean the surface for proper sealer adhesion. 6 Wait at least 48 hours at a minimum temperature of 32 F (0 C) and no rain so the sand surface is dry. 7 Best Practice: (See online video. 2 people needed.) Apply one (1) coat of DELUXE SERIES NATURAL LOOK SEALER using a sprayer in 60 sq. ft. sections, then use a solventresistant foam roller to remove the excess sealer left on the surface. 8 DELUXE SERIES NATURAL LOOK SEALER is water repellant, rain safe, after 90 min. 9 Let the sealer dry for 24 hours before using the sealed area. INSTALLATION EDGES

74 Polybind Sealer Chart Product Name Eco Seal High Gloss +COLOR ENHANCER Eco Seal Low Gloss +COLOR ENHANCER Eco Seal High Gloss Eco Seal Low Gloss Eco Seal Zero Gloss Formulation Water-Based Water-Based Water-Based Water-Based Water-Based Finish High Gloss Low Gloss High Gloss Low Gloss Zero Gloss Color Enhancer Vibrant Vibrant None None None Joint Stabilizer Film-Former GRID AND FABRIC Damp Surface Rain-Safe After Dry Cast Concrete Paver Wet Cast Natural Stone 24 hours 24 hours 24 hours 24 hours 24 hours Masonry Before Before Before Before Before After After After After After EDGES Before Before Before Before Before After After After After After INSTALLATION Protect and enhance your hardscape project with one of the many sealer products offered by Polybind. To learn more, visit Polybind.com To learn more, visit us online at Polybind.com 74

75 DELUXE SERIES Wet Look High Gloss Vibrant Color Enhancer Satin Look Low Gloss Subtle Color Enhancer Natural Stone Zero Gloss +COLOR ENHANCER Natural Look Natural Look Finish, Zero Gloss MULTI-PURPOSE Wet Cast Natural Look Finish Zero Gloss Wet Cast Low Gloss +COLOR ENHANCER Solvent-Based Solvent-Based Water-Based Water-Based Water-Based Solvent-Based High Gloss Low Gloss Zero Gloss Zero Gloss Zero Gloss Low Gloss Vibrant Subtle Vibrant None None Subtle 90 minutes 90 minutes 24 hours 24 hours 24 hours 90 minutes GRID AND FABRIC Before Before Before Before Before Before After After After After After After Before Before Before Before Before Before After After After After After After All products are SCAQMD compliant. First test the product on a small, less-observed area of approximately 4 sq. ft. (0.4 m 2 ) to ensure results meet your expectations. Expect final color, variation and shade (lightness-darkness) to vary in most instances. All concrete or natural stone exhibit variations, therefore the sample charts should be used as a general guideline only when selecting sealer type. Color matches cannot be guaranteed. To learn more, visit us online at Polybind.com 75 INSTALLATION EDGES