- TECHNICAL SAFETY DATA SHEET
|
|
- Myron Palmer
- 5 years ago
- Views:
Transcription
1 MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE Chem-Rez (Epoxy/Aggregate Coating) - TECHNICAL SAFETY DATA SHEET -
2 MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE MATERIAL SAFETY DATA SHEET - Chem-Rez (Epoxy/Aggregate Coating) Adress: 8428 Shepard RD SE T2C 1R6, Calgary, AB Phone: [403] Fax: [403] PART ONE - GENERAL WORK INCLUDED Consists of all labour, materials, and equipment or any combination thereof to install Chem-Rez epoxy/ aggregate resurfacing in accordance with drawings or specifications stated herein RELATED WORK Installer shall examine project to determine suitability and repot any deviations. Installer shall coordinate work so as not to delay project, and shall request to be the last contractor on the project INSTALLER QUALIFICATION The dealer shall assume responsibility that: A) The product shall be supervised and installed in a professional manner. B) The installation shall be performed by a trained installer DRAWINGS AND PRODUCT DATA A) The installer shall submit drawings and product data. References and listing of completed installations may also be submitted. B) The installer will clearly indicate on plan layout all surfaces to be covered by epoxy/aggregate SAMPLES The installer shall submit representative samples for approval prior to starting work. PART TWO - PRODUCTS ACCEPTABLE MANUFACTURERS The approved manufacturer shall be Chemtron Manufacturing Ltd MATERIALS Materials shall consist of Natural stone, a washed, sized, cleaned, dried, bagged, and pre-measured, hardshell natural aggregate. The stone shall be combined on the job site with Chem-Rez epoxy, a 100% solids epoxy specially formulated for resurfacing pavements. The combination of both ingredients form a durable, high-strength, abrasion-resistant material which is porous and stain resistant. The aggregate is bonded to the sub-surface. No solvents or dilutants shall be used COMPONENTS The epoxy mix shall be a two-component system which consists of two parts resin to one part catalyst by volume....continued Pg 2of5 Phone: (403) Fax: (403)
3 EPOXY MIX When the resin and catalyst are blended, the mix shall have a viscosity of at least 2000 cps at 75 F. The mix shall be transparent in the use state. PART THREE - EXECUTION INSTALLATION A) PREPARATION OF SUBSURFACE: New concrete subsurfaces shall cure for 21 days prior to installation. All subsurfaces shall be clean and free of dirt, dust, oil, grease, frost, and abnormal moisture content. Subsurfaces shall be completely dry. Loose concrete and some types of paint shall be removed prior to installation by grinding, chipping, or sanding. Temperature of surface shall be above 6C? F when using Chem-Rez epoxy. A coating of Chem-Rez Primer shall be applied over the concrete in colder climates. The epoxy/aggregate installation shall be trowelled over wet Primer. A membrane is required on wood balconies or wood floors. B) APPLICATION OF EPOXY/AGGREGATE: Two parts Component A, resin, shall be mixed with one part Component B, curing agent, by volume. Pour the premixed epoxy over the appropriate amount of Natural stone in a 6 cu. ft. cement mixer and tumble until all stones are coated with epoxy, approximately 5-10 minutes. Dump and spread coated stones over subsurface and trowel to depth of 3/8 to 1/2 inch depending on stone size and subsurface irregularities. Material shall be trowelled to a flat and level finish. A 50 lb bag of stone plus 1 litre of Chem-Rez epoxy (pre-mixed) will cover approximately 8 to 10 sq ft CLEAN-UP Project shall be clean and neat after installation. Any remainder is the propety of the installer; the installer will remove remainder promptly SECURITY Project shall be protected to prevent disturbance of curing epoxy/aggregate until set, 6 to 10 hours, depending on ambient temperature PERFORMANCE The Chem-Rez installation shall meet or exceed the performance/product specifications listed herein, plus: 1) Freeze-thaw cycling; no effect 2) Shrinkage; no effect 3) Flammability; self-extinguishing 4) Adhesion; 2000 psi Pg 3of5 Phone: (403) Fax: (403)
4 PROPERTIES PHYSICAL PROPERTIES - unmixed COMPONENT A - RESIN: Weight per gallon-pounds 9.3 3,000-4,000 CPS Specific gravity at 75 F 1.14 Clear COMPONENT B - CURING AGENT: Weight per gallon-pounds CPS Specific gravity at 75 F 0.98 Golden Shelf Life - closed containers 1 Year PHYSICAL PROPERTIES - mixed: Weight per gallon-pounds ,000-3,000 CPS Specific gravity at 75 F 1.08 Solids at weight 100% Pot Life at 75 F-150 grams minutes Light Golden PRODUCT TESTING: Hardness Shore D9 75 F ASTM D Hardness Shore A9150 F ASTM D Tensile Strength PSI9 75 F ASTM D-638 6,000+ Tensile Elongation %9 75 F ASTM D Adhesion, Tensile Shear PSI9 75 ASTM D MIXING RATIO: BY VOLUME: BY WEIGHT: 2 Parts A 1 Part B 2.40 lbs Part A 1.00 lbs Part B SECTION EIGHT - PREPERATION INFORMATION Mix 2 Pats A with 1 Pat B for 2 to 3 minutes. The Chem-Rez epoxy will turn cloudy or milky in color. Let the mixed Chem-Rez epoxy stand for 3 to 5 minutes, until it turns clear. Then give the Chem-Rez epoxy a inal shot mix of 2 minutes before using. NOTE: Mixed epoxies cannot be guaranteed to be UV or light stable. Specifications subject to change at manufacturer s option without notice. Pg 4of5 Phone: (403) Fax: (403)
5 CAUTION Acrylast Acrylic Sealant is available from our manufacturing facilities. Information on availability and ordering can be obtained by contacting our representatives. CHEMTRON WARRANTS THAT THIS PRODUCT CONFORMS TO THE CHEMICAL DESCRIPTION CONTAINED IN THE PRODUCT TECHNICAL BROCHURE. NO STATEMENTS OR RECOMMENDATIONS CONTAINED THEREIN ARE TO BE CONSTRUED AS INDUCEMENTS TO INFRINGE ANY RELEVANT PATENT, NOW OR HEREAFTER IN EXISTENCE. NO OTHER WARRANTEIS, WHETHER EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANT ABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THIS UNIT. CHEMTRON NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBLIGATION OR LIABILITY OTHER THAN SUCH AS IS EXPRESSLY SET FORTH HEREIN. UNDER NO CIRCUMSTANCDES SHALL CHEMTRON BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FORM THE USE OR HANDLING OF THIS PRODUCT. Pg 5of5 Phone: (403) Fax: (403)
Epoxy & Pebblestone Fax: We ship all over the USA U.V.
Epoxy & Pebblestone www.epoxyandpebblestone.com 623-688-6077 Fax: 623.594.7177 dave@epoxyandpebblestone.com We ship all over the USA U.V. EPOXY PHYSICAL PROPERTIES: Composition: Solids Content: Mix Ratio:
More informationMcKinnon Materials, Inc th Commerce Park Blvd. Tampa FL, Phone: (813) Fax: (813)
PHYSICAL PROPERTIES: Composition: Solids Content: Mix Ratio: 3 to 1 Viscosity: Pot Life: McKinnon Materials, Inc. 5612 56 th Commerce Park Blvd. Tampa FL, 33610 Phone: (813) 622-7031 Fax: (813) 621-9017
More information- TECHNICAL DATA SHEET
MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE 1958. Multiflex (Co-Polymer Sealant - TECHNICAL DATA SHEET pg1 Phone: (403) 252-7803 Fax: (403) 2522384 www.chemtron.ca - TECHNICAL DATA SHEET
More informationDECOCOLOR FLOORING SYSTEM
AIA Specification DECOCOLOR FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions of the
More informationDECOFLAKE DECORATIVE FLOORING SYSTEM
AIA Specification DECOFLAKE DECORATIVE FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions
More information1/8 DECORATIVE BROADCAST FLOORING SYSTEM
AIA specification AIA specification AIA Specification 1/8 DECORATIVE BROADCAST FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or
More information1/16 Single Broadcast Polymer Flooring System
specification 1/16 Single Broadcast Polymer Flooring System Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions
More informationAdvantages: Advantages include:
Elgin, Illinois Hi-Tek Polymers Floor Description: Hi-Tek Polymers Floor is a decorative thin-set epoxy system of 1/4" (6,3mm) to 3/8 (MM) which meets all the standards set by the NTMA (National Terrazzo
More informationEasy to apply Nonflammable Low odor Castable Make excellent materials of construction
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Primer Application Thickness Dry Film Thickness Typical Uses Polymer Concrete polymer concrete is an excellent alternative to acid
More informationBROADCAST KITCHEN FLOORING SYSTEM
AIA specification AIA specification AIA Specification Part 1 - GENERAL BROADCAST KITCHEN FLOORING SYSTEM General Provisions A. Work to be covered by this section, under written specification or by drawing,
More informationDIVISION 3 - CONCRETE Section Concrete Toppings Concrete Resurfacing Concrete Rehabilitation
Spec Component: SC-012-03/10 Sikadur 35, Hi-Mod LV DIVISION 3 - CONCRETE Section - 03550 Concrete Toppings 03920 Concrete Resurfacing 03930 Concrete Rehabilitation Part 1 General 1.01 Summary A.. This
More informationApplication Guidelines for PPC Coatings Flooring
Application Guidelines for PPC Coatings Flooring PPC Coatings Flooring System General Objective The objective of this specification is to describe the material and workmanship necessary to achieve desired
More informationDIVISION 9 FINISHES Section Floor Finishes
Spec Component: SC-032-0807 Supersedes: SS-032-0601 DIVISION 9 FINISHES Section 09600 Floor Finishes Part 1 - General 1.01 Summary A. This specification describes the application of a waterproofing, slip
More informationPOLYACRYLATE MODIFIED THINSET TERRAZZO 1
PART 1 - GENERAL GUIDE SPECIFICATION POLYACRYLATE MODIFIED THINSET TERRAZZO - REVISED AUG 02 1.1 RELATED DOCUMENTS A. Section includes thin set Polyacrylate Modified Terrazzo flooring (and integral cove
More informationDIVISION 7 THERMAL AND MOISTURE PROTECTION Section Traffic Coatings
Spec Component: SC-720-03/10 Sikalastic 720/745 Traffic System DIVISION 7 THERMAL AND MOISTURE PROTECTION Section 071800 Traffic Coatings Part 1 - General 1.01 Summary A. This specification describes the
More informationPOLYMER CONCRETE 100 EPOXY POLYMER CONCRETE DILUTE ACIDS RESISTANCE
RECOMMENDED APPLICATIONS Polymer Concrete 100 is a three-component, epoxy polymer concrete used for the construction of chemical resistant floors, pads, curbing, trenches and sumps. Polymer Concrete 100
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete Vapor-Shell GUIDE SPECIFICATION SECTION 09725 PART 1 GENERAL 1.01 SECTION INCLUDES A. Provisions
More informationDIVISION 9 - FINISHES Section Coatings
Spec Component: SC-031-0907 Sikagard 62 DIVISION 9 - FINISHES Section 09900 Coatings Part 1 - General 1.01 Summary A. This specification describes the overlay of interior horizontal surfaces with an epoxy
More informationBroadcast Parking Garage System
AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete
More information- TECHNICAL DATA SHEET
MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE 1958. Acrylast (Acrylic Sealant) - TECHNICAL DATA SHEET - - TECHNICAL DATA SHEET - MAKERS OF ADHESIVES, SEALANTS, AND RELATED PRODUCTS SINCE 1958.
More informationBlome Sealant 55MT Flexible, Moisture-tolerant Epoxy Novolac Joint Sealant
Blome Sealant 55MT Flexible, Moisture-tolerant Epoxy Novolac Joint Sealant PRODUCT DESCRIPTION Blome Sealant 55MT is a two-component, moisture-tolerant, 100% solids epoxy novolac elastomer with excellent
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Color System GUIDE SPECIFICATION SECTION 09725 PART 1
More informationCP-24CC Potassium Silicate Concrete
CP-24CC Potassium Silicate Concrete PRODUCT DESCRIPTION Blome CP-24CC is a two component, potassium silicate concrete used for acid resistant pump pads, equipment pads, curbing, floors and sumps. CP-24CC
More informationAraldite MCU 7 US. Advanced Materials. Technical Datasheet. Product Description. Features. Typical Properties*
Araldite MCU 7 US Product Description Araldite MCU 7 US is a medium-fast curing adhesive in a series of single component, solvent free, moisture curable, liquid polyurethane adhesives, which range in speed
More informationBlome Sealant 55MT Flexible, Moisture-tolerant Epoxy Novolac Joint Sealant
Blome Sealant 55MT Flexible, Moisture-tolerant Epoxy Novolac Joint Sealant PRODUCT DESCRIPTION Blome Sealant 55MT is a two-component, moisture-tolerant, 100% solids epoxy novolac elastomer with excellent
More informationWood Floor Bonding Systems
Part 1 - General Wood Floor Bonding Systems DIVISION 9 - FINISHES Section 09 64 00 Wood Flooring Wood Parquet Flooring Spec Component: SC-302-0311 SikaBond-T21 1.01 Summary A. This specification describes
More informationSECTION EPOXY TERRAZZO
SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationPOLYMER CONCRETE 800 NON-SHRINK VINYL ESTER POLYMER CONCRETE, CONCENTRATED HYDROFLUORIC ACID RESISTANCE
RECOMMENDED APPLICATIONS Polymer Concrete 800 is a three-component, vinyl ester polymer concrete used for the construction of chemical resistant floors, pads, curbing, trenches and sumps. Polymer Concrete
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy-Shell 1000 Color System GUIDE SPECIFICATION SECTION 09725 PART 1
More informationCC-1004 Ultra High Temperature Epoxy Adhesive
CC-1004 Ultra High Temperature Epoxy Adhesive PRODUCT DESCRIPTION TYPICAL USES Blome CC-1004 is a two part, high temperature, epoxy adhesive used for the installation of abrasion resistant brick and tile
More informationARALDITE AY 557 Resin Hardener HY 557
Advanced Materials ARALDITE AY 557 Resin Hardener HY 557 RAPID, CLEAR EPOXY ADHESIVE Description ARALDITE AY 557 Resin/Hardener HY 557 epoxy system is a rapid-setting, two-component clear material. Mixing
More informationARALDITE AW 136 Resin Hardener HY 5049 EPOXY LAMINATING ADHESIVE
ARALDITE AW 136 Resin Hardener HY 5049 EPOXY LAMINATING ADHESIVE DESCRIPTION: Araldite AW 136 resin/hardener HY 5049 epoxy adhesive is a two-part laminating system used for fabricating skis, snowboards
More informationSanitile 945 SL PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. 100% solids epoxy
SELECTION & SPECIFICATION DATA Generic Type Description Features 100% solids epoxy Sanitile 945 SL is a 100% solids, high performance, epoxy coating designed for concrete. Sanitile 945 SL is a selfleveling
More informationARALDITE 2011 A/B (AW 106 Resin/Hardener HV 953) MULTI-PURPOSE EPOXY ADHESIVE
ARALDITE 20 A/B (AW 06 Resin/Hardener HV 953) MULTI-PURPOSE EPOXY ADHESIVE DESCRIPTION: Araldite 20 A/B epoxy adhesive is a multi-purpose, viscous material that is suitable for bonding a variety of materials,
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Single Quartz Broadcast System GUIDE SPECIFICATION SECTION
More informationDocument Library TS Data Sheet
Document Library TS Data Sheet 46004 46005 46006 Rev:2 Effective: 01/11/2002 3M Marine Premium Filler Data Sheet Status: Active 3M Part No.(s) 46004 46005 46006 3M Part Descriptor(s) Pint Quart Gallon
More informationWood Floor Bonding Systems
Part 1 - General Wood Floor Bonding Systems DIVISION 9 - FINISHES Section 09 64 00 Wood Flooring Wood Parquet Flooring Spec Component: SC-301-0809 SikaBond-T35 1.01 Summary A. This specification describes
More informationTraffic Bearing Membrane
7 07 18 11 Traffic Coatings Qualideck Traffic Bearing Membrane High-solids, 2-component polyurethane waterproofing, traffic bearing systems for vehicular and pedestrian areas PACKAGING Q152 Primer: 3 gal
More informationDivision 3 - Concrete Section Concrete Rehabilitation
Spec Component: SC-023-03/10 Sikadur 32, Hi-Mod Division 3 - Concrete Section 03930 - Concrete Rehabilitation Part 1 - General 1.01 Summary A. This specification describes the grouting of cracks with epoxy
More informationDivision 3 - Concrete Section Concrete Rehabilitation
Spec Component: SC-039-03/10 Sikadur 23, Lo-Mod Gel Division 3 - Concrete Section 03930 - Concrete Rehabilitation Part 1 - General 1.01 Summary A. This specification describes the patching of exterior
More informationSECTION RESILIENT TRACK SURFACING
SECTION 32 2000 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply
More informationDIVISION 3 CONCRETE Section Concrete Rehabilitation
Spec Component: SC-010-03/10 Sika Pronto 19 TF DIVISION 3 CONCRETE Section 03930 Concrete Rehabilitation Part 1 General 1.01 Summary A. This specification describes the grouting of cracks / sealing of
More informationHDX TECHNICAL SPECIFICATION
HDX TECHNICAL SPECIFICATION SafeLane surface overlay Pavement Substrate A Cargill Deicing Technology Product Providing customers with deicing solutions that save lives and enhance commerce. Helping to
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy Metallic System GUIDE SPECIFICATION SECTION 09725 PART 1 GENERAL
More informationSECTION UNIT PAVERS
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Concrete pavers. 2. Detectable warning pavers. 3. Warning stripe pavers. 1.2 SUBMITTALS A. Product Data: For the following: 1. Pavers.
More informationARALDITE AV 119 EPOXY ADHESIVE PASTE
ARALDITE AV 119 EPOXY ADHESIVE PASTE DESCRIPTION: Araldite AV 119 epoxy adhesive is a one-component, multi-purpose paste that is thixotropic and is designed for heat curing at temperatures from 248 F to
More informationALABAMA DEPARTMENT OF TRANSPORTATION
ALABAMA DEPARTMENT OF TRANSPORTATION DATE: January 9, 2014 Special Provision No. 12-0817 SUBJECT: High Friction Surface Treatments for Asphalt Pavements, Project Number 99-303-690-000-302, Jefferson County
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More information3 Scotch-Weld TM. Bulk Adhesives. General Purpose 60 CA Hi-Strength Laminating 92 Hi-Strength Post-forming 94 CA. Technical Data May, 2008
3 Scotch-Weld TM General Purpose 60 CA Hi-Strength Laminating 92 Hi-Strength Post-forming 94 CA Bulk Adhesives Technical Data May, 2008 Product Description 3M Scotch-Weld Bulk Adhesives are industrial
More informationSPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay
2004 Specifications SPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay 1. Description. Furnish and place a multi-layer polymer overlay consisting of a crack seal, polymer resin and aggregates.
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Sparse Flake System GUIDE SPECIFICATION SECTION 09725
More informationSIDER-BASE CONCENTRATE AAC/ MONOSIDERAL AAC THE ULTIMATE OLD-WORLD AERATED CONCRETE-AAC DECORATIVE STUCCO SYSTEM
SIDER-CRETE, INC. 153 Regur Road Hawkinsville, GA 31036 USA Ph: 478.892.9800 www.sider-crete.com SIDER-BASE CONCENTRATE AAC/ MONOSIDERAL AAC THE ULTIMATE OLD-WORLD AERATED CONCRETE-AAC DECORATIVE STUCCO
More informationEPOXY TERRAZZO 1 REV. 8/02
PART 1 - GENERAL GUIDE SPECIFICATIONS section 9400 EPOXY THINSET TERRAZZO (Without A Crack Suppression Membrane) REVISED MAY 2003 1.1 RELATED DOCUMENTS A. Section includes thin-set epoxy terrazzo flooring
More informationEVERLAST CONCRETE TECHNOLOGIES PROTECTION PRODUCTS SECTION CONCRETE ADDITIVES AND ADMIXTURES
EVERLAST CONCRETE TECHNOLOGIES PROTECTION PRODUCTS SECTION 03060 CONCRETE ADDITIVES AND ADMIXTURES GENERAL 1.1 SECTION INCLUDES A. Concrete additives and admixtures for the following applications: 1. Concrete
More information3910 E. McKinney Denton, TX P.O. Box Dallas, TX EZ WALL CONCENTRATE, INC
EZ Spread Coarse Sand Description EZ Spread is the perfect material for small projects and repairs. This factory prepared blend of portland cement proprietary additives, and sand. EZ Spread is designed
More informationSeal- Krete High Performance System
hp.seal-krete.com Rust-Oleum - 11 Hawthorn Parkway, Vernon Hills, IL 800.323.7357 PART 1 GENERAL 1.01 SECTION INCLUDES Seal- Krete High Performance Poly- Shell 70007 System GUIDE SPECIFICATION SECTION
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX K 15 Premium Self-Leveling Underlayment A Self-Leveling Underlayment that Consists of a Blend of Portland Cements and Other Hydraulic Cements for Interior Applications SECTION
More informationASH GROVE KOLORSTONE BROOMCOAT MIXING KIT. Spec Sheets Contents: Kolorstone Broomcoat Mixing Spec Sheet Kolorflex Admixture Spec Sheet
ASH GROVE KOLORSTONE BROOMCOAT MIXING KIT Spec Sheets Contents: Kolorstone Broomcoat Mixing Spec Sheet Kolorflex Admixture Spec Sheet kolor stone broomcoat 1. Product Name ASH GROVE KOLOR STONE Broomcoat
More informationDIVISION 7 - THERMAL AND MOISTURE PROTECTION Section Joint Sealers Elastomeric and non-elastomeric sealant
Spec Component: SC-073-03/11 Sikadur Combiflex SG Part 1 - General DIVISION 7 - THERMAL AND MOISTURE PROTECTION Section 07900 Joint Sealers Elastomeric and non-elastomeric sealant 1.01 Summary A. This
More informationA. This Section includes resinous flooring systems with epoxy body coat(s).
SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes resinous flooring systems with epoxy body coat(s). 1. Application Method: Troweled (Slurry, Seeded or Broadcast
More informationRESINOUS FLOORING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS Bid #2017-17 A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment
ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions
More informationSKATE ON LAYKOLD Specification
Acrylic Sport & Recreational Surfaces SKATE ON LAYKOLD Specification PART 1 GENERAL 1.1 DESCRIPTION Scope: This guide specification covers the construction and installation for the SKATE ON LAYKOLD inline
More informationNSP SPECIALTY PRODUCTS Technical Data Sheet. NSP 120 High Performance Epoxy Coating
Description: NSP 120, a two component, 100% solids, high build epoxy coating, offers excellent chemical, corrosion and abrasion resistance in severe industrial environments. This extremely versatile product
More informationAcrylic Tennis & Recreational Sport Surfaces. ADVANTAGE Laykold System Specification
Acrylic Tennis & Recreational Sport Surfaces ADVANTAGE Laykold System Specification PART 1 GENERAL 1.1 DESCRIPTION A. Scope: This guide specification covers the application of the Advantage Laykold system.
More information3 Scotch-Weld TM. Epoxy Adhesive 2158 B/A. Technical Data December, 2009
3 Scotch-Weld TM Technical Data December, 2009 Product Description 3M Scotch-Weld is a gray, two-part, high strength adhesive that chemically cures at room temperature. It has good adhesion to a variety
More informationPacific Polymers Elasto-Deck 5000MR Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000MR OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide
More informationDATA SHEET UNIQUE FLEXICRETE XP Polymer Modified Mortar
DATA SHEET UNIQUE FLEXICRETE XP Polymer Modified Mortar Product Description UNIQUE FLEXICRETE XP Polymer Modified Mortar is an easy to use polymer modified non-shrink/volume stable trowel grade mortar.
More informationTOPCOAT Restoration Specifications Structural Concrete
TOPCOAT Restoration Specifications Structural Concrete Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications Structural Concrete
More informationFIVE STAR PRODUCTS, INC.
FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 Page 1 of 8 DESIGN-A-SPEC GUIDELINES RAPID SURFACE REPAIR EASY MIX CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS
More informationVapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring
advanced moisture control, inc. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring 250 polished concrete slabs! Made in Southern California,
More informationFlorock Seamless Flooring Systems
Part 1: General Florock Seamless Flooring Systems Architectural Specification FloroQuartz BC Epoxy - Colored Quartz 1/8 (0.125 mm) Double Broadcast Flooring System 1.01 System Description A. Roller-applied
More informationSECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 05 16 SUBSURFACE PREPARATION FOR FLOOR FINISHES SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph
More information3 Scotch-Weld. Control Joint Sealant DP-5106, Self-Leveling, Gray. Technical Data July, 2006
Technical Data July, 2006 Product Description 3M Scotch-Weld DP-5106 is a self-leveling, gray, rapid setting, two-component polyurethane. It is packaged as 1:1 ratio liquids in duo-pak cartridges. With
More informationA-9,250 Parking Structure Resurfacing Cement Look
A-9,250 Page 1 A-9,250 Parking Structure Resurfacing Cement Look Description This specification includes the repair and resurfacing methods used when applying Americrete products over cracked, spalled,
More informationMEMBRANE 510/510R Low VOC Flexibilized, Urethane Membrane mils
GREEN BUILDING FEATURES Contributes towards satisfying Credit 4.2 under LEED Contains recycled post industrial crushed glass Contains rapidly renewable materials Meets California South Coast Air Quality
More informationCOMPRESSIVE STRENGTH 14,000 psi (984 kg/cm 2 ) (Actual field strength may vary, from
ESCOWELD 7505E/7530 High Strength, Very Fluid, 3-Part Epoxy Grout Technical Bulletin # 1612D Product Description ESCOWELD 7505E/7530 is a highly flowable, epoxy grout system engineered for use with dynamically
More informationPRODUCT DATA SHEET Sikadur 33
PRODUCT DATA SHEET HIGH-MODULUS, HIGH-STRENGTH, STRUCTURAL, VERY RAPID-CURING EPOXY, SMOOTH-PASTE AD- HESIVE PRODUCT DESCRIPTION Sikadur 33 is a 2-component, 100 % solids, moisture-tolerant, high-modulus,
More informationAcrylic Tennis & Recreational Sport Surfaces. COLORCOAT System Specification
Acrylic Tennis & Recreational Sport Surfaces COLORCOAT System Specification PART 1 GENERAL 1.1 DESCRIPTION A. Scope: This guide specification covers the application of the Laykold ColorCoat system. Advanced
More informationTechnical Datasheet Ashland Performance Materials
Document 2437 V4 F2, Language EN V1, Approved 2013-4-3, 2013 Ashland Inc. Page 1 (5) Description PLIOGRIP 7700 two-part systems are high-strength, structural adhesives which are resistant to exposure to
More informationARALDITE A/B. Advanced Materials TOUGHENED, FAST-CURE EPOXY ADHESIVE. Description. Applications. Advantages
Advanced Materials ARALDITE 200- A/B TOUGHENED, FAST-CURE EPOXY ADHESIVE Description ARALDITE 200- A/B epoxy adhesive is a two-component, fast-cure, multi-purpose, thixotropic paste that cures fast at
More informationFlorock Seamless Flooring Systems
Architectural Specification -- FloroCryl Shop MMA (Methyl Methacrylate) - Silica Sand Single Broadcast 1/16 (1.59 mm) Flooring System Part 1: General 1.01 System Description A. Roller-applied penetrating
More informationFLOORING INSTALLATION SYSTEMS. Product Catalog
FLOORING INSTALLATION SYSTEMS Product Catalog Custom Building Products is North America s leader in flooring preparation systems. It s easy to say you re an industry leader, but we prove it every day with
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroBuild PT/ HT Epoxy Mortar ¼ Power Trowel or Hand Trowel Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer
More informationDIVISION 3 - CONCRETE Section Control Joint Sealers
Spec Component: SC-072A-03/10 Sikadur 51 SL DIVISION 3 - CONCRETE Section 03930 - Control Joint Sealers Part 1 - General 1.01 Summary A. This specification describes the sealing of saw-cut, control, and
More informationCustomTech, co-developed by Custom Building Products and top commercial contractors, is the industry s most advanced flooring preparation system.
CustomTech, co-developed by Custom Building Products and top commercial contractors, is the industry s most advanced flooring preparation system. FLOORING PREPARATION SYSTEMS CustomTech is the latest product
More information1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU.
1. Rapid Set Cement 2. Methods of preparation 3. How to stage a job site 4. Installation Mix, place, finish 5. Coloring the TRU natural TRU Rapid Set is NOT Portland Cement Rapid Set is a Calcium Sulfoaluminate
More informationFLUID APPLIED WATERPROOFING SECTION SPECIALTY COATINGS
SECTION 07 14 00 FLUID APPLIED WATERPROOFING SECTION 09 96 00 SPECIALTY COATINGS Multicoat Seamless Waterproofing System for Fountains & Ponds ************************************************************************************************************************
More informationRENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION
STUC-O-FLEX RENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION 09 97 23 PART 1-GENERAL 1.00 SCOPE: Manufacturer's specifications containing the requirements necessary
More informationProperty Test Method Typical Value
Application is a high gloss 100% solid, UV curing, permanent industrial floor coating intended for use on concrete floors. The Kemiko product range is cured using proprietary Quaker UV curing units. is
More informationSystem Specification CEM-DYE 250 SYSTEM Division 9 Finishes Section Staining and Transparent Finish
NOTE TO SPECIFIER: Cem-Dye 250 System is a fluid applied liquid metallic dye stain used on portland cement concrete and cementitious overlayments and polyurethane top coated system. S-5000 is a metallic
More informationSTERI-FLAKE 470 HYBRID ESTER POLYMER, LIGHT-MEDIUM TRAFFIC, FLAKE FILLED FLOOR SYSTEM LOW ODOR MMA ALTERNATIVE FEATURES
FEATURES Low Odor & VOC Very Fast Cure Unique Multi Colored Patterns Tough, Durable & Seamless Floor Good UV Stability Protects Substrate from Chemical or Physical Attack Integral Cove, Base and Curb (optional)
More informationSECTION TOPICAL MOISTURE VAPOR MITIGATION SYSTEM
TOPICAL MOISTURE VAPOR MITIGATION SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings, documents and general provisions of the Contract, and other related construction documents such as Division 01
More informationDIVISION 3 CONCRETE Section Concrete Rehabilitation Gravity Feed Crack Repair
Spec Component: SC-005-03/10 Sikadur 52 DIVISION 3 CONCRETE Section - 03930 Concrete Rehabilitation Gravity Feed Crack Repair Part 1 General 1.01 Summary A. This specification describes the grouting of
More informationTechnical Data Sheet EpoGlass PU Code: 65
Product Description: Two-component, effective acrylic aliphatic - polyurethane topcoat. Material creates a highly durable coating layer, suitable for marine industrial atmosphere and excellent resistance
More informationPRODUCT DATA SHEET Sikadur 31 CF Normal (formerly Sikadur 731)
PRODUCT DATA SHEET (formerly Sikadur 731) 2-part Thixotropic Epoxy Adhesive PRODUCT DESCRIPTION Sikadur-31 CF Normal is a solvent-free, moisture tolerant, thixotropic, structural two part adhesive and
More informationDOWSIL ALLGUARD Silicone Elastomeric Coating
Technical Data Sheet Water-based silicone elastomer for waterproofing above-grade exterior masonry substrates Features & Benefits Provides long-term waterproofing protection Maintains water protection
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 096623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments
ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments SECTION 07 26 19 TOPICAL MOISTURE VAPOR EMISSION SYSTEM WITH ARDEX
More information80201R StoColor Acryl Flat Acrylic-Based, Vertical Above-Grade Exterior Wall Coating for Recoating Prepared, Previously Painted Surfaces
Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com 80201R StoColor Acryl Flat Acrylic-Based, Vertical
More information