Model: Quadro mm. Height adjustable table 23 mm laminate on MDF steel frame. EN 527-2:2002 and EN 527-3:2002.

Transcription

1 Cube Design A/S Vadstedvej 212 DK-8450 Hammel Order no Appendices 3 Test Report Material: Model: Quadro mm Type: Materials: Height adjustable table 23 mm laminate on MDF steel frame Sampling: Method: The test material was sampled by the client and received at the Danish Technological Institute EN 527-1:2011 Office furniture - Work tables and desks - Part 1: Dimensions EN 527-2:2002 Office furniture. Work tables and desks. Mechanical safety requirements: Section 3. EN 527-3:2003 Office Furniture Work tables and desks Methods of test for the determination of the stability and the mechanical strength of the structure , , 5.2.2, 5.3.2, 5.4.2, 5.5.2, Period: The testing was carried out from to to Result: Model Quadro 5730 fulfils the requirements of EN 527-1:2011, EN 527-2:2002 and EN 527-3:2002. Individual results appear from Appendices 1 and 2. Storage: Terms: The test material will be destroyed after 1 month, unless otherwise agreed. The test has been performed according to the attached conditions, which are according to the guidelines laid down by DANAK (The Danish Accreditation). The testing is only valid for the tested specimen. The test report may only be extracted, if the laboratory has approved the extract , Danish Technological Institute, Wood Technology, Taastrup Test responsible Verifier

2 Appendix 1 EN 527-1:2011 Dimensions h 1 t 1 and t 2 k 1 k 2 k 3 f 1 and f 2 Height of the work surface Max. desk top thickness Min. height of knee Min. depth of knee Min. depth of foot Min. height of min. foot clearance Sitting only Standing only Sit/stand Work table/desk type Measured Result Type A Fully adjustable N/A N/A Passed At the front, t 1 55 b 23 Passed At 500 mm from the front edge, t 2 80 b 61 Passed Applies only to tables with a height more than 850 mm Sitting only and sit/stand From 600 mm to 800 mm from the front edge, f 1 g 1 Min. legroom depth c Sitting only and sit/stand 700 d 789 Passed Passed Passed Passed Standing only From front edge 120 N/A to 150 mm, f Passed D Min. desk top depth g Passed Sitting only and W Min. legroom width sit/stand Passed Standing only 790 N/A a Max. increment of 20 mm b Only applies to sitting and sit/stand work tables/desks c The construction of the product shall ensure the min. legroom depth d Measured from the floor e The min. and max. values shall be obtained f 600 mm can in some situations be acceptable. E.g. when 17 or smaller flat screens are used, providing that the work surface is not against the wall and that two people are not sitting one in front of each other. Information about these limitations shall be provided with the product g The dimension D is measured as the smallest dimension at the work area

3 Appendix 2 Test Method Result acc. to EN 527-2:2002 section 3 General safety requirements EN 527-2:2002 Passed Result acc. to EN 527-2:2002 section 4 Stability under vertical load EN 527-3: Passed Stability with open drawers EN 527-3: N/A Strength under vertical load EN 527-3: Passed Strength under horizontal force EN 527-3: Passed Fatigue under horizontal force EN 527-3: Passed Fatigue under vertical force EN 527-3: Passed Drop test EN 527-3: Passed

4 Appendix 3 Photo

5 The general conditions pertaining to assignments accepted by Danish Technological Institute shall apply in full to the technical testing or calibration at Danish Technological Institute and to the completion of test reports or calibration certificates within the relevant field. Danish Accreditation (DANAK): DANAK is the national accreditation body in Denmark in compliance with EU regulation No. 765/2008. DANAK participates in the multilateral agreements for testing and calibration under European co-operation for Accreditation (EA) and under International Laboratory Accreditation Cooperation (ILAC) based on peer evaluation. Accredited test reports and calibration certificates issued by laboratories accredited by DANAK are recognized cross border by members of EA and ILAC equal to test reports and calibration certificates issued by these members accredited laboratories. The use of the accreditation mark on test reports and calibration certificates or reference to accreditation, documents that the service is provided as an accredited service under the company's DANAK accreditation according to EN ISO IEC Construction Product Directive: The Danish Technological Institute guarantees that employees carrying out tests to be used together with harmonized standards under notification no according to EU regulation 305/2011, article 43, satisfy all the requirements made for capability, integrity and impartiality. You find the CPR here: September 2015