INFORMATION AND PROCEDURES FOR OBTAINING N, NA, NPT, NV, N3 & NS NUCLEAR CERTIFICATES AND CERTIFICATION MARK CLASS l, 2, 3, MC, CS, CC &TC

Transcription

1 Two Park Avenue New York, NY U.S.A. tel fax www. asme.org INFORMATION AND PROCEDURES FOR OBTAINING N, NA, NPT, NV, N3 & NS NUCLEAR CERTIFICATES AND CERTIFICATION MARK CLASS l, 2, 3, MC, CS, CC &TC The ASME Certification Mark is used to indicate that items stamped comply with the Quality Assurance Requirements of Section III, Subsection NCA, General Requirements for Divisions 1, 2 and 3, as well as the specific requirements of other applicable Subsections. Code Books required are shown on the Code Book Order Form, which can be downloaded from our website. The Applicant is required to meet the Quality Assurance requirements of the current Code. Alternatively, if the Applicant wishes to limit its Quality Assurance Program to the requirements of a Code edition and addenda earlier than the latest published, that Code edition and addenda must be shown in the application (Scope of Work Requested by Applicant) and the Quality Assurance Requirements of that Code edition and addenda must be met. The requirement for possession of an official Certification Mark and Certificate is for the purpose of safeguarding the use of the Certification Mark when the Applicant certifies that the equipment is built to the requirements of the ASME Code. It is not the intention of ASME to unduly restrict the use of the Certification Mark, but rather to prevent unauthorized use under all circumstances. ASME Certificates and Certification Mark are furnished from this office only. The Quality Assurance Manual and documentation which support understanding of the program must be in English. ASME, by the use of Survey Teams, reviews the implementation of the Applicant's Quality Assurance Program. Any findings are discussed between the Team and the Applicant, and a report is submitted to ASME, which either authorizes the issuance of the Certificate(s) or requests additional action by the Applicant. The Survey Team consists of ASME Consultants, the Accredited Authorized Inspection Agency and a representative of the Enforcement Authority in Jurisdictions. The "Guide for ASME Nuclear Survey Teams for Certificate Holders" provides a checklist of the elements of a Quality Control System. The Applicant is required to indicate the corresponding cross references to the provisions in the Quality Control Manual which address these elements. The completed Guide must be provided by the Applicant to the ASME Survey Team. Surveys for a Quality Assurance Program Certificate, are also available. It recognizes that an organization has an acceptable Quality Assurance program and the capability to staff, equip, and otherwise implement the program. There is no stamp issued with a Quality Assurance Program Certificate until ASME conducts an implementation audit for conversion to a Certificate of Authorization. Payment of charges for the Survey will be as follows: 1. ASME will submit an invoice to the Applicant for the fees and expenses of the ASME Consultants and the National Board Representative (when the National Board acts on behalf of the Enforcement Authority), administrative charges, the $3,000 three year fee per Certificate and the $300 fee for use of the Certification Mark on initial issuance. Prices are subject to change without notice. A2.10-2/14 (1/4)LH

2 2. The Applicant pays their Accredited Authorized Inspection Agency directly. 3. The Applicant pays their Enforcement Authority directly, if applicable. Quality Assurance Systems vary in complexity, detail and structure as do an Applicant's size, scope and volume of work. Because of the many variables, it is impossible to project the length of time required for the Survey Team's visit. The cost could range from $35,000 to $75,000 for Domestic and from $40,000 to $90,000 for International. Price ranges on applications for multiple sites may vary Please bear in mind that the fee ranges quoted are based on typical average surveys and that your survey could require more or less time. These estimates are not firm quotations. If your facility requires an extended survey, because of its complexity, the ranges could be exceeded. Our Survey Team will make every effort to conclude their visit in a minimum length of time. ASME requires an advance deposit of $10,000 for surveys prior to establishment of survey dates. This will be applied to the cost of the survey. If the Applicant withdraws their application after the remittance is received by ASME, there is an administrative fee of $500 which will be deducted from the original remittance. Please submit the application through CA Connect. Please return the completed Accreditation/Certification Agreement and fees to: ASME Accreditation/Certification Processing Dept. 22 Law Drive PO Box 2900 Fairfield, NJ Applicants for renewal must also supply the information requested in Form A2.70, Additional Information to be Provided with Application for Renewal Survey. In addition, it is requested that the Accreditation/Certification Agreement and Form A2.70 be ed to ca@asme.org. To avoid unnecessary expense and delay, the Applicant should consult with its Accredited Authorized Nuclear Inspection Agency for advice as to the probable acceptability of the Quality Assurance Program. A complete list of Accredited Organizations holding Authorized Inspection Agency Certificates, and the Code Sections for which they are accredited is shown as a link on the website. The program demonstration/implementation being presented to the Survey Team must be able to demonstrate/implement all aspects of the Quality Assurance Program which will include: 1. Material Organization activities for all Applicants applying for this additional scope to their N-Type Certificates of Authorization. 2. Material Organization activities for Applicants applying for N-Type Certificates of Accreditation with material organization activities appearing in their Certificate scope. 3. A separate demonstration/implementation item which is representative of a pressure relief device (achievement of capacity certification is not required) for all Applicants applying for multiple Certificates of Authorization with an NV Certificate of Authorization being one of them. 4. Class 3 PE Plastic Piping activities for Applicants applying for N-Type Certificates of Authorization whose scope of activity appearing on their Certificate will permit them to fabricate, assembly, install, manufacture, and/or supply Class 3 PE Plastic Pipe. Please review the Information for Applicants for ASME Certificates of Authorization or Quality System Certificates, which can be found on our website. A2.10-2/14 (2/4)

3 Upon receipt of completed application and deposit, and notification that the Applicant is ready for a survey of the Quality Assurance Program and its implementation, a mutually acceptable date for the survey will be arranged between the Applicant and ASME. The Applicant is responsible for obtaining the concurrence of the Accredited Authorized Inspection Agency and Enforcement Authority, where applicable, for the survey dates. Cancellation of survey dates is subject to a monetary penalty, deducted from the advance deposit, as follows: $2,000 for cancellation after acceptance of the survey dates. $3,500 for cancellation within 2 months of the survey dates. $6,000 for cancellation within l month of the survey dates. In addition to the above, the Applicant will be charged for any committed travel and miscellaneous expenses associated with the cancelled survey. Note that one complete application set must be submitted for each different plant location and field site. Multiple Certificate and Certification Mark requests at a single location require only one copy of each form. For Applicants for NV Certificates, a list of Testing Laboratories Holding ASME Certificates of Acceptance for Conducting Tests of Pressure Relief Devices is shown as a link on the website. ASME will make every effort to conduct an evaluation of the Applicant's program at the earliest possible date after receipt of the application forms and deposit. However, it should be expected that a lead time of four to six months is usual because of scheduled surveys of other companies. ASME can accept no liability for consequences to the Applicant which may be the result of the survey or subsequent ASME actions. A renewal survey will be scheduled approximately eight to twelve weeks prior to the current expiration date to assure continuity of the Certificates. Certificate Holders have the option to request an extension to their current Certificate expiration date to complete current work. Such a request for extension to complete work in progress must be received, by ASME, at least ninety days prior to the current expiration date. A check for $2,000 per Certificate must accompany the request. The request must contain information concerning order entry dates, order numbers, quantity of each order, item descriptions and the completion dates. A copy of the request must be sent to the Enforcement Agency for the location of the work in progress, and your Accredited Authorized Inspection Agency. The Certificate Holder shall also request their Accredited Authorized Inspection Agency to evaluate their present activity and provide a report to ASME. The evaluation shall include the current effectiveness of the management and quality program relative to what was in place and presented to the ASME Survey Team at the last survey. An extension, if granted, will be for six months, with no further extension. The extension will only cover work listed in the request. A Certificate Holder who voluntarily terminates a survey in progress is not eligible for this type of extension of expiration date. A brochure listing the various sections of the Boiler and Pressure Vessel Code and other ASME publications required for obtaining ASME Certificates is available on our website. Subscription to the indicated sections of the ASME Boiler and Pressure Vessel Code is required for certification to assure that Code users have the latest applicable Code rules. Effective with the issuance of the 2007 Edition of the Boiler and Pressure Vessel Code, the electronic version, purchased from a licensed reseller is acceptable, as well as the published version by ASME. The rules published in the Code are subject to revision from time to time. These revisions are published annually in addenda to the BPV Code. The effective date for which the latest published Code edition and addenda become the current Code edition and addenda is six months after the date of publication of each such edition and addenda. The Applicant or Certificate Holder is not precluded from implementing the latest published Code edition and addenda earlier than the effective date. Additionally, interpretations of the rules are published in supplements to the Code. These addenda and supplements are provided to subscribers, as part of their basic subscription, to assure their awareness of the latest rules, revisions and interpretations. A2.10-2/14(3/4)

4 Reproduced documents from any source are not accepted for ASME certification, as they provide no assurance of completeness or that the user will be made aware of revisions and interpretations of the applicable Code sections. Applicants are advised that registration of data report forms may be required by the legal authority of a state or municipality of the United States or province of Canada. Information regarding such requirements is available from the applicable legal authority or The National Board of Boiler and Pressure Vessel Inspectors, 1055 Crupper Ave., Columbus, OH ; telephone (614) ; fax (614) , info@nationalboard.org website Additionally, a Synopsis of Boiler and Pressure Vessel Laws, Rules and Regulations in the United States and Canada is available from The National Board of Boiler and Pressure Vessel Inspectors. If you have any questions, please contact the ASME Conformity Assessment Department via ca@asme.org. A2.10-2/14 (4/4)

5 Two Park Avenue, New York, NY ASME Application for Accreditation/Certification Company: (Company name as it will appear on the Certificate) Division: (Division, department, etc., if it is to appear on the Certificate) This application is for the following location: Address: (Give full address) City State Country Postal code Plant New If renewal, complete the following: Field Site Renewal Current Certificate Number(s): Expiration date: Check the Certificate(s) being applied for: *N Nuclear *N3 Transportation/Storage RTP Reinforced Thermoset *NA Nuclear Assembly Containers Plastic Vessels *NPT Nuclear Partials NO Nuclear Owner QEI Qualification of Elevator *NV Nuclear Safety Valves MO Material Organization, Inspectors *NS Nuclear Supports AIA Authorized Inspection BPE BioProcessing Equipment Agency NQA-1 Nuclear Quality Assurance Stamps ASME is switching to a Single Certification Mark. If you are renewing an existing certificate you will be asked to return your Code Symbol Stamp by no later than January 1, For detailed information about the switch to Single Certification Mark please review the FAQ s on New ASME Mark on our website Please indicate below the number of stamps of each size you would like to receive. If you currently hold stamps you may request an equal number of new certification stamps at no charge. Stamps exceeding the number you currently hold will be subject of the standard stamp fee, as will all stamps accompanying new certificate issuances Number of Stamps Requested: ½ ¾ * Important: If marked with an * you must complete the following: The Authorized Inspection Agency performing our Code inspection is Application must be signed on page A9.54-2/14 (1/2) LH Page 1 of 2

6 Company Abbreviation: Please indicate if the company chooses to use an abbreviation on the nameplate or in the stamping. Yes No If yes, the abbreviation will consist of Note: A Certificate Holder may use either the company s full name or the above abbreviation on the nameplate or in the stamping. The Certificate Holder must list the company s full name as listed on the ASME Certificate on the ASME Manufacturer s Data Report. Accreditation/Certification Agreement The organization listed on the front of this Application for Accreditation/Certification (the Applicant ) performs or subcontracts the design, fabrication, production, testing, assembly, construction and/or installation of items, or provides a service to the aforementioned activities, at the address given, and makes this application to The American Society of Mechanical Engineers (ASME) for the appropriate Certificate of Accreditation, Certificate of Acceptance, or Certificate of Authorization permitting use of the associated Certification Mark. The Applicant: (1) Agrees to use the Certificate and/or Stamp in accordance with the applicable ASME Code or Standard and supplemental conformity assessment requirements governing this application. (2) Agrees to return the stamp and/or Certificate anytime ASME may so request, at the time the Applicant discontinues the work covered, or at the time of expiration, if not renewed. (3) Accepts the conduct of announced or unannounced audits as required by the appropriate ASME accreditation/certification body. Access to the inspection site to conduct audits, reviews or surveys, including travel to and from the site, is the responsibility of the Applicant. If access is blocked or impeded, ASME is not responsible for the Applicant failing to receive, or continue to have accreditation/certification. (4) Agrees to indemnify and hold harmless ASME and its agents from and against any costs (including legal fees and expenses) and any direct, indirect, incidental or consequential damages (including loss of profits or business opportunity) arising out of any claim or cause of action in any way related to this Agreement or the subject matter hereof, including but not limited to claims based on contract, tort (including negligence), strict liability or breach of warranty (express or implied). (5) Understands that the Applicant s use of the ASME mark may be allowed provisionally by ASME in its discretion until a decision is made on an appeal of an action of an ASME subcommittee, committee or board and accepts the obligation to pay all legal fees and expenses and ASME's cost for recovering the Certificate and stamp if not returned. (6) Agrees to pay ASME for all fees, expenses and expenditures associated with the Review/Survey/Audit conducted by ASME. Legal Company Name: Signed: Title: Signature must be by a Company Officer or Designee Date: A9.54-2/14 (2/2) Page 2 of 2

7 Two Park Avenue, New York, NY Form D Company: (Company name as it will appear on the Certificate) Division: (Division, department, etc., if it is to appear on the Certificate) Location (provide full address): Corporate/Mailing Plant Field Site Contact name: Fax: Title: Telephone: Company Website: Jurisdictional Authority (if applicable): Authorized Inspection Agency of record (if applicable): Recommended hotel or motel for team (provide name, full address, and telephone numbers): First choice Second choice Recommended airport (include city name): Miles from airport to lodging: Miles from lodging to office/plant/site: Recommended airport to lodging transfer: Taxi Signed: Limo Hotel provided limo Title: Rent car Pickup by company Date: A4.7-3/13 Page 1 of 1

8 Two Park Avenue, New York, NY Form A (Company name including Department or Division as it will appear on the Certificate) (Address as it will appear on the Certificate) Check Certificate Requested: New Renewal If Renewal, enter current certificate No.(s): Certificate of Authorization (Includes Stamp) Type: Shop Certificate Field Site Certificate Is this a Corporate Certificate Extension? Yes: Certificate No.: No Subcontracting (N or N3 Certificate of Authorization Only) Certificates (With No Stamp) Type: Quality Assurance Program Certificate {Manual review only - No program demonstration/implementation} Certificate of Authorization (Corporate) {requires extension for stamp} {Partial program demonstration/ implementation} NS Certificate of Authorization {for supports only stamp not required} {Full program demonstration/implementation} Check Certificate and Classes of Construction DIVISION 1 DIVISION 2 DIVISION 3 N** Class CS MC CC TC SC TP**** Vessels Pumps Valves Piping Systems PE Plastic Piping Systems Storage Tanks Core Support Structures Concrete Containments (N (Subcontracting) Scope Not Permitted) Shop Assembly Transport Packaging**** NV** Class CS MC CC TC SC TP**** Pressure Relief Valves N3 Class CS MC CC TC SC Transportation/Storage Containments Shop Assembly NPT** **** Class CS MC CC TC SC TP**** Fabrication without Design Responsibility PE Plastic Pipe Fabrication with Design Responsibility (Appurtenances only) NS (Supports Only) Class MC CC TC SC TP**** Fabrication without Design Responsibility Fabrication with Design Responsibility NA** Class CS MC CC TC SC TP**** Field Installation PE Plastic Pipe Shop Assembly* PE Plastic Pipe A4.4 1/13 (1/2)LH Form A must be signed on page

9 Form A Page 2 of 2 Activities performed at another location*** If you wish to furnish material, please complete and return Form C: Form C Enclosed Information for the ASME Survey Team: Enter P (Perform Activity) or S (Subcontract Activity) or both in the spaces below for each activity: Procurement of material Design Fabrication Installation Testing Examination Code Edition and Addenda used if other than the latest: Edition Addenda Copies of the application, including this form, should be provided to the AIA when the application is sent to ASME. Legal Company Name: Signed: (Must be a Company Officer or Designee) Title: Date: * Only if another Certificate Holder is taking overall responsibility and applying N stamp. This Certificate Holder will apply NA stamp only. ** Listing of Miscellaneous items (NCA-1270) on the applicable Certificate(s) is not required. Miscellaneous items (NCA-1270) are identified and characterized in applicable Design Specifications as either components, parts, appurtenances, piping subassemblies, or material, and organizations holding the appropriate Certificate(s) for the required stamping as a component, part, appurtenance, piping subassembly, or for furnishing items as material may provide NCA-1270 items without any further listings in their Certificate(s) scope. *** Specific address and activities such as quality assurance, design, purchasing, forming, storage, etc., performed at another location, which will appear in the Scope. **** Class TP for Division 3 Transport Packaging is limited to the 1995 Edition, 1997 addenda up to and including the 1998 Edition, 2000 Addenda and to the N and NPT Certificate. Class TP is available only when an existing contract/purchase order requires this class of construction. A statement identifying the Class TP contract/purchase order scope of work must be enclosed with the application. A4.4 1/13 (2/2)

10 Two Park Avenue, New York, NY Form C (Company name including Department or Division as it will appear on the Certificate) (Address as it will appear on the Certificate) Certificate Requested Check One: (Use separate Form C for each Certificate) NEW RENEWAL If renewal, enter the current Certificate No: Certificate Type: (Check One) Shop/Field Site Corporate Certificate If Shop/Field Certificate, is this a Corporate Certificate extension: Yes: Certificate No. No NCA-3800 QSC Program Scope addition to N Type Certificate*** Certificate No.: Check the Type of Operation(s) and Material(s) to be listed in Certificate Scope: Manufacturing Supplying Additional Operations Requested *: Ferrous Materials Nonferrous Materials Utilization of Unqualified Source Material Approval and Control of Suppliers Qualification of Noncertified Material Organizations Shipment of Material from Qualified Material Organizations to Other Parties Activities performed at another location**: Information for the ASME Survey Team: Indicate in the space provided if you perform P or subcontract S the following operations: Material Testing Weld Repair Nondestructive Testing Heat Treatment Identify your product forms by indicating in the space provided the type of material from which the product is made. ( F for Ferrous and NF for Nonferrous). When applying for both Manufacturing and Supplying activities, also identify the applicable activity for each product. ( M for Manufacturing and S for Supplying). PRODUCT FORMS Welding Material Bars Fittings Made From NPT Stamped Tubular Products Bare Electrodes Bare Wire Threaded Fasteners Seamless Tubular Products Covered Electrodes Consumable Inserts Castings Tubular Products Welded Without Filler Metal Flux Cored Electrodes Forgings Tubular Products Welded With Filler Metal (NPT Stamped) Metal Cored Electrodes Powdered Filler Metal Plates Structural Shapes Strip Electrodes Clad Plates Sheet Prestressing Systems (Div. 2) Seamless Fittings Strip Strands Couplings Flanges Brazing Material Wires Coupling Components Fittings Welded Bars Non Load Carrying Without Filler Metal Anchorages Materials Anchorage Components Fabrication of Semi Finished Product Forms Rounds Billets Concrete Reinforcing Systems (Div. 2) Hollows Ingots Reinforcing Bars Hot Rolled Wire Semi Finished Strip Fabrication of Reinforcing Systems Hot Rolled Rod Mechanical Splice Products Prestressing Systems A4.6-1/13 (1/2) Form C must be signed on page

11 Form C Page 2 of 2 NCA-3900 QSC Program Check the Type of Operation(s) and Material(s) to be listed in Certificate Scope: Nonmetallic Material Manufacturer Plastic Concrete Plastic Grout Nonmetallic Material Constituent Supplier Admixtures (Air Entraining, Chemical, Mineral, Grout Fluidifier) Aggregates Cement Cement Grout Ice & Water Polyethylene Material Manufacturer Polyethylene Material Supplier Polyethylene Source Material Manufacturer Natural compound Pigment Concentrate Compound Polyethylene Compound Activities performed at another location**: Information for the ASME Survey Team: Indicate in the space provided if you perform P or subcontract S the following operations: Material Testing Nondestructive Testing Signed: Title: (Signature must be by a Company Officer or designee) Date: For a Material Organization scope addition to an N Type Certificate, a copy of the application including this form should be provided to the AIA when the application is sent to ASME. * These operations are already included among the activities that may be performed under an N Type Certificate (N, NA, NPT, NS). The N-Type Certificate Holder is to indicate which additional operations will be performed under the program. Listing of these operations in the N Type Certificate scope is not required but must be addressed in the N Type Certificate Holders QA Manual and be included in the program demonstration/implementation presented to the ASME Survey Team. ** Specific address and activities such as Quality Assurance, Purchasing, Forming, Storage, etc., performed at another location, which will appear in the Scope. *** For N Type Certificates of Authorization/Accreditation, a program demonstration/implementation of the Material Organization activities is required. A4.6-1/13 (2/2)

12 Two Park Avenue New York, NY U.S.A. tel fax SCHEDULING INFORMATION NEW/RENEWAL APPLICANTS ASME will make every effort to conduct an evaluation of an Applicant's program at the earliest possible date after receipt of the application forms and fees. However, there is an average lead time to schedule surveys, from receipt of completed application and fees of four months due to scheduled surveys of other companies. To minimize costs for Applicants, ASME tries to schedule a series of surveys in the same area of the world. Therefore, in order for ASME to schedule your survey, please answer the following two questions. Please note that if you check as soon as possible for Question 1, or a date much earlier than four months, we will in general only be able to schedule at those times, if another company in your area cancels their date. Question 1 What is the earliest date that you are available for a survey? {Note: Renewal surveys are required to be scheduled approximately 8-12 weeks prior to the current expiration date.} As soon as possible, or Question 2 What weeks or dates are not acceptable to you (due to Holidays, plant shutdowns, etc.) between your first available date and eight months from the date of your application? Company Signature: Date: Your survey will be scheduled at the earliest possible date consistent with your responses and in conjunction with other companies in your area. We, therefore, expect you to accept the dates that we assign. Lack of acceptance may result in a long delay until the next series of surveys are scheduled in your area or a substantial increase in your costs if a Team must be sent to do your survey alone. We cannot schedule your survey until the completed application, fees and this completed form are received. ASME Conformity Assessment Department A4.14E2-1/13(1/1)

13 Team Size Questionnaire Company Name: Division: Address Give the full physical address of the locations and activities for which this application is being submitted. Include all on site and off site locations with number of buildings, their size and acreage. (Company name as it would appear on the Certificate) (Division/Department name, if it is to appear on the Certificate) List of Additional Locations and/or Diagram of Location(s) Attached. For each building indicate the activities performed and the number of employees performing activities which control/affect quality. Provide distances with units between buildings from the main facility. Indicate best mode of transportation and length of time to reach buildings/locations, i.e., walking, car, airplane, train It is suggested that an illustration be provided. Attach additional pages if necessary. Facility Limitations Are there any limitations on the entry to your facilities that could obstruct the progress of the survey activities or prevent non nationals entry to certain buildings or areas in the facility?

14 Facility Limitations (continued) Is there a shortened work week schedule, multiple shifts? Facility Restrictions Are there restrictions on the use of personal computer, cell phones, flash drives or other electronic equipment in your facilities? Facility Services Are copying, computer, phone and internet services available to the team within your facility? Use of copying machines? Yes No Use of computers? Yes No Internet Service Available? Yes No Code Work Code work performed since the last ASME Survey Has any certification or application of the Code Symbol Stamp been performed under the ASME Certificate since the last ASME Survey? Yes No Language Are the employees (involved with the QA Program and have an impact on quality) proficient in speaking English? Yes No

15 Two Park Avenue New York, NY U.S.A. tel fax www. asme.org ADDITIONAL INFORMATION TO BE PROVIDED WITH APPLICATION FOR RENEWAL SURVEY The procedures of the Committee on Nuclear Certification (CNC) have been revised to provide some flexibility in establishing the size of Teams for renewal of N-Type Certificates. The procedures state that at the time of application for renewal, the Certificate Holder shall identify to ASME the programmatic changes that have been made and accepted by the ANIS since the issuance or last renewal of the Certificate. We would therefore like a report from you providing information on the programmatic changes that have occurred since your last survey. The report should also cover the following: 1. Significant changes in the organization from those in effect at the time of issuance or last renewal of the Certificate. This could include reorganization, a merger or acquisition, or change in key personnel. 2. Any changes in the QA Manager/Director, including the frequency of change in this position and the experience level of personnel filling this position. 3. Any major rewrite of the QA manual or any such major rewrite planned to be submitted to the Team as the survey. 4. Any complete rewrite of the QA manual as a new version or edition. 5. Any significant change in the magnitude of business within the scope of the Certificate. (Example: The company business was only manufacturing parts or small components, and now will be manufacturing large or complex components.) Please provide this information with the application and copy your AIA of record on the report submitted regarding the programmatic changes. A2.70-1/13LH

16 ASME Boiler and Pressure Vessel Code A N I N T E R N A T I O N A L C O D E Invoice Request Form go.asme.org/bpvc13

17 Invoice Request Form: Please complete the following Invoice Request Form; and then send to: ASME Customer Care 22 Law Drive, Box 2300 Fairfield NJ USA Phone: (toll-free), (Monday through Friday, 8:00 a.m.-5:30 p.m., EST) Fax: (24 hours / 7 days) customercare@asme.org ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. Ordering information for domestic and international orders may be found below. Prices are subject to change without notice. ASME Account No. (if available): Ship To: Company Name: Address: City / State / Zip or Postal Code: Country: To the attention of: Phone: BILL To: Company Name: Address: City / State / Zip or Postal Code: Country: Phone: To the attention of:

18 ASME s Boiler and Pressure Vessel Code (BPVC) 2013 Sections Publications: order No. ISBN Quantity List Price (USD) line Total BPVC-2013 Sections: I, Rules for Construction of Power Boilers $ II, Materials: II-A, Ferrous Material Specifications (two volumes) 60002A $ II-B, Nonferrous Material Specifications 60002B $ II-C, Specifications for Welding Rods, Electrodes, and Filler Metals 60002C $ II-D, Properties (Customary) 60002D $ II-D, Properties (Metric) 6002DM $ III, Rules for Construction of Nuclear Facility Components: III-NCA, General Requirements for Division 1 and Division R $ Division 1: III-NB, Class 1 Components 60003B $ III-NC, Class 2 Components 60003C $ III-ND, Class 3 Components 60003D $ III-NE, Class MC Components 60003E $ III-NF, Supports 60003F $ III-NG, Core Support Structures 60003G $ III-NH, Class 1 Components in Elevated Temperature Service 60003H $ III Appendices 60003A $ Division 2: III-2, Code for Concrete Containments $ Division 3: III-3, Containments for Transportation and Storage of Spent Nuclear Fuel and High Level Radioactive Material and Waste $ Division 5: III-5, High Temperature Reactors $ IV, Rules for Construction of Heating Boilers $ V, Nondestructive Examination $ VI, Recommended Rules for the Care and Operation of Heating Boilers $ VII, Recommended Guidelines for the Care of Power Boilers $ VIII, Rules for Construction of Pressure Vessels: VIII-1, Division $ VIII-2, Division 2, Alternative Rules $ VIII-3, Division 3, Alternative Rules for Construction of High Pressure Vessels $ IX, Welding and Brazing Qualifications $ X, Fiber-Reinforced Plastic Pressure Vessels $ XI, Rules for Inservice Inspection of Nuclear Power Plant Components $ XII, Rules for Construction and Continued Service of Transport Tanks $ Code Cases: Boilers and Pressure Vessels * $ Code Cases: Nuclear Components 60012N* $ Binder with Label $20.00 Complete BPVC-2013 (approx. 10% discount off Suggested List Price) 6X $12, Complete BPVC 2013 with 34 Binders 6X $13, ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. SUBTOTAL: *Codes Cases are issued four times per year. This price reflects inclusive purchase of all Code Cases issued during the upcoming, two-year publishing cycle for BPVC However, individual Code Cases are also available for separate purchase. Visit or contact ASME Customer Care for details.

19 Product Certification Packages List prices indicated in the following Product Certification Packages include pertinent publications of the 2010 Edition of ASME s Boiler & Pressure Vessel Code (BPVC). Upon official publication of the 2013 Edition of the BPVC on July 1, 2013, list prices of these Product Certification Packages will be revised accordingly. Please contact ASME CustomerCare for any questions. Publications: order No. Quantity List Price (USD) line Total Product Certification Packages per Designator : A (Assembly of Power Boilers) BPVCB $2, E (Electric Boilers) BPVCE $2, H (Cast Iron Section Heating Boilers) BPVCH2 $ H (Field Assembly of Boilers) BPVCH $1, H (Heating Boilers, Except Cast Iron) BPHLW $3, HLW (Lined Potable Water Heaters) BPHLW $3, HV (Heating Boiler Safety Valves) BPVHV $3, M (Miniature Boilers) BPVCM $4, N, NA, NPT, NS (N-Type Certificates of Authorization and Certificates of Accreditation) BPNPT $3, NV (Nuclear Safety and Pressure Relief Valves includes BPVC-II-A, Section II, Part A, Ferrous Materials Specifications) BPNVA $3, NV (Nuclear Safety and Pressure Relief Valves includes BPVC-II-B, Section II, Part B, Nonferrous Materials Specifications) BPNVB $3, NV (Nuclear Safety and Pressure Relief Valves includes BPVC-II-D, Section II, Part D, Properties, Customary or Metric) BPNVD $3, N3 (N-Type Certificates of Authorization and Certificates of Accreditation) PVCN3 $2, QSC (Quality Systems Certificates Material Manufacturers, Material Suppliers) PVCMS - Contact ASME RP (Fiber-Reinforced Plastic Vessels) BPVRP $ S (Power Boilers) / PP (Pressure Piping) BPVCA $4, T (Transport Tanks) BPVCT $4, TD (Transport Tanks, Rupture Disc Devices) BPVCTD $3, TV (Transport Tanks, Safety Valves) BPVCTV $3, U (Pressure Vessels, Division 1) BPVUM $4, UD (Rupture Disc Devices) BPVCUD $4, UM (Miniature Pressure Vessels) BPVUM $4, UV (Pressure Vessels, Safety Valves includes BPVC-VIII-1, Pressure Vessels, Division 1) BPUV1 $4, UV (Pressure Vessels, Safety Valves includes BPVC-VIII-2, Pressure Vessels, Division 2) BPUV2 $4, U2 (Pressure Vessels, Division 2) BPVU1 $4, UV3 (Pressure Vessels, Safety Valves) BPUV3 $4, U3 (Pressure Vessels, Division 3) BPVU3 $4, V (Boiler Safety Valves) BPVCV $3, ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. SUBTOTAL: Related ASME Codes and Standards: Publications: order No. ISBN Quantity List Price (USD) line Total Official Spanish-language Translations: BPVC-I-2010 Seccion 1, Reglas para la Construccion de Calderas de Energia XS0010* $ B31.8S-2010 Gestión de Integridad de Sistemas de Gasoductos A21410* $95.00 B16 Series on Valves, Fittings, Flanges and Gaskets: B Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard M01509* $ B Factory-Made Wrought Buttwelding Fittings J10907* $ B Forged Fittings, Socket-Welding and Threaded M01611* $65.00 B Valves Flanged, Threaded and Welding End J01809* $ B Large Diameter Steel Flanges: NPS 26 Through NPS 60 Metric/Inch Standard J12911* $115.00

20 Related ASME Codes and Standards (continued): Publications: order No. ISBN Quantity List Price (USD) line Total B31 Series on Piping: B Power Piping A05812* $ B Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids A03809* $ B Gas Transmission and Distribution Piping Systems A04510* $ B31.8S-2010 Managing System Integrity of Gas Pipelines A45S10* $ B Surface Texture, Surface Roughness, Waviness and Lay A14312* $ BPE-2012 Bioprocessing Equipment A14309* $ CSD Controls and Safety Devices for Automatically Fired Boilers A09112* $93.00 FSS Series: API 579-1/ASME FFS Fitness-For-Service A $ API 579-1/ASME FFS Fitness-For-Service CD Format A164C $ FFS Fitness-for-Service Print and CD Package AX6407 $1, FSS Fitness-For-Service Problem Manual A $ Nuclear: AG Code on Nuclear Air and Gas Treatment A $ N Self-Operated and Power-Operated Safety-Related Valves Functional Specification Standard A00084* $35.00 N Nuclear Power Plant Air-Cleaning Units and Components A08502* $75.00 N Testing of Nuclear Air-Treatment Systems A08207* $55.00 N In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems A16507* $39.00 NOG Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder) A11910* $ NQA Quality Assurance Program Requirements for Nuclear Facilities A105E $ NUM Rules for Construction of Cranes, Monorails, and Hoists (with Bridge or Trolley or Hoist of the Underhung Type) J14309* $ OM-2009 Operation and Maintenance of Nuclear Power Plants A $ QAI Qualifications for Authorized Inspection J95010* $60.00 QME Qualification of Active Mechanical Equipment Used in Nuclear Power Plants A13607* $95.00 RA-S-2008 Standard for Level 1 / Large Early Release Frequency Probabilistic Risk Assessment for Nuclear Power Plant Applications A $ PCC Series on Post Construction: PCC Guidelines for Pressure Boundary Bolted Flange Joint Assembly A15010* $89.00 PCC Repair of Pressure Equipment and Piping A17511* $ PCC Inspection Planning Using Risk-Based Methods A16807* $69.00 PTB Series on Pressure Vessels: PTB ASME Section VIII Division 2 Criteria and Commentary A19509* $ PTB Guide to Life Cycle Management of Pressure Equipment Integrity A19609* $95.00 PTB ASME Section VIII Division 2 Example Problem Manual A20410* $ PTC Pressure Relief Devices C06108* $95.00 PVHO Safety Standard for Pressure Vessels for Human Occupancy A09212* $ RTP Reinforced Thermoset Plastic Corrosion Resistant Equipment J127E1* $ ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. SUBTOTAL: *Also available as digital download (single-user PDF.) Visit or contact ASME Customer Care for details.

21 ASME s Boiler and Pressure Vessel Code (BPVC) 2013 For all other ASME programs -- including product / personnel certifications, training & development courses, professional conferences and publications visit: Ordering Information When ordering with your company purchase order, please make sure that your ASME account number, if available, is indicated. This account number can be found on ASME invoices, packing lists and statements. CA, FL, GA, IL, KY, TX and DC purchasers will be invoiced for applicable sales tax. Canadian purchasers will be invoiced 7% GST, unless ASME is furnished with a valid tax exemption certificate. For international funds transfers, please indicate your ASME order number, invoice number, and account number. Failure to indicate your ASME order number, invoice number, and account number may delay shipment considerably. Please be sure to include your bank s wire transfer fees in the total amount submitted. Proforma invoices showing all charges, including shipping / handling charges, will be furnished upon receipt of order. Orders received with payment will be invoiced for shipping / handling charges. ASME s standard shipping / handling charges may be viewed here: International Orders Advance payment is required for all international orders. ASME accepts most major credit cards, including MasterCard, VISA, American Express, Discover and Euro. ASME also accepts checks written in some international currencies. Contact ASME to determine which currencies are acceptable or visit: Prices are subject to change without notice. Two Park Avenue New York, NY U.S.A.