X-EM6H, X-EW6H, X-EF7H, X-EM8H, X-EM10H, X-EW10H Threaded Studs for Steel
|
|
- Giles Doyle
- 5 years ago
- Views:
Transcription
1 X-EM6H, X-EW6H, X-E7H, X-EM8H, X-EM10H, X-EW10H Threaded Studs for Steel Product data Dimensions X-EM6H/EW6H- -9 P8 X-E7H-7-9 P8 General information Material specifications M6/W6 o 3.7 o 3.8 o Lg 9 L X-EM8H- - P8 o o X-EM8H-15- P10 o 8 Carbon steel shank: HRC 56.5 Zinc coating: 1 ) 5 13 μm 1 ) Zinc coating (electroplating for corrosion protection during construction and service in protected environment) o 5.5 M8 o 4.5 o 8 o 5.5 M8 o 4.5 o 10 Recommended fastening tools DX 460, DX 76, DX 76 PTR, DX 600 N 3.5 L g L X-EM10H-24- P X-EW10H P10 See X-EM/ X-EW fastener program in the next pages and Tools and equipment chapter for more details. o M o 4.5 o 10 W10 o or dimension details see chapter fastener selection o 10 Approvals ICC-ES ESR-2347 (USA): M : UL: EX2258: ABS, LR: X-EW6H, X-EW10H, X-EM8H X-EW6H, X-EW10H X-EW6H, X-EW10H all types Applications Examples Base plates for pipe rings Hanging with threaded couplers Electrical boxes Miscellaneous attachments /
2 Load data Recommended loads astener Shank designation d s x L s [mm] N rec [kn] V rec [kn] M rec [Nm] X-EM6H, X-EW6H, X-E7H 3.7 x X-EM8H, X-EM10H 4.5 x X-EW10H x Conditions Redundancy (multiple fastening) must be provided. Global factor of safety for static pull-out >3 (based on 5% fractile value). Predominantly static loading. Strength of fastened material must be considered. Observance of all application limitations and recommendations. The recommended loads in the table refer to the resistance of the individual fastening and may not be the same as the loads N and V acting on the fastened part. V M N Note: If relevant, prying forces need to be considered in design, see example. Moment acting on fastener shank only in case of a gap between base and fastened material. Z 3 Z 2 Arrangement to prevent moment on shank: Coupler tight against steel Z1 V N Z V N 182 / 13
3 Application requirements Thickness of base material Minimum steel thickness: X-EM6H/EW6H, X-E7H X-EM8H/EW8H, X-EM10H/EW10H t ll 4 mm 6 mm tii Thickness of fastened material t I L g t washer t nut mm T rec ti Spacing and edge distances Edge distance and spacing: c = s 15 mm c c s s tii Corrosion information The intended use only comprises fastenings which are not directly exposed to external weather conditions or moist atmospheres. or further detailed information on corrosion see relevant chapter in Direct astening Principles and Technique section. /
4 Application limits X-EM6H, X-EW6H, X-E7H S235Jxx 8 S275Jxx 6 4 S355Jxx Steel strength, R m [N/mm 2] Steel thickness tii, [mm] DX 460 tool: À X-E7H- -9 Á X-EM6H- 9, X-EW6H- -9 X-EM8H Steel thickness, tii [mm] S235Jxx S275Jxx Steel strength, R m [N/mm 2] 1 S355Jxx 2 DX 460 tool: À X-EM8H- - DX 76 / DX 76 PTR tool with X PTR fastener guide: Á X-EM8H-15- X-EM10H / EW10H Steel thickness tii, [mm] S235Jxx 10 S275Jxx 8 S355Jxx Steel strength, R m [N/mm 2 ] DX 76 / DX 76 PTR tool: À X-EM10H-24- DX 600 N tool: Á X-EW10H P / 13
5 astener selection and system recommendation astener program Base material astened astener Threading Shank DX tools thickness thickness Designation 1 ) Item no. length lengths t ll,min [mm] t l,max [mm] L g [mm] L s [mm] X-EM6H-8-9 P DX X-EM6H-11-9 P DX X-EM6H--9 P DX X-EW6H-11-9 P DX X-EW6H--9 P DX X-EW6H-28-9 P DX X-EW6H-38-9 P DX X-E7H-7-9 S DX X-EM8H-11- P DX X-EM8H-15- P DX X-EM8H-15- P DX 76 PTR, DX X-EM10H-24- P DX 76 PTR, DX X-EW10H P DX 600 N 1 ) Type of threading: M = metric; W6, W10 = Whitworth 1 / 4 ; 3 / 8 ; 7 = rench 7 mm Cartridge recommendation Tool energy adjustment by installation tests on site astener Tool Base material Base material thickness (mm) Cartridge selection X-EM6H, X-EW6H DX 460 S /11M green /11M yellow S /11M green 6 6.8/11M yellow S /11M yellow X-E7H DX 460 S /11M green 8 6.8/11M yellow S /11M green 6 6.8/11M yellow S /11M yellow X-EM8H DX 460 S235, S /11M red 8 6.8/11M black S /11M black /
6 astener Tool Base material Base material thickness (mm) Cartridge selection X-EM8H DX 76 PTR S /18M blue 8 6.8/18M red S /18M blue 7 6.8/18M red 6.8/18M black S /18M red /18M black X-EM10H DX 76 PTR S /18M yellow S /18M yellow /18M blue 8 6.8/18M red S /18M red 8 6.8/18M black X-EW10H DX 600 N S /18 blue /18 red /18 black S /18 blue 8 6.8/18 red astening quality assurance 6.8/18 black S /18 red 7 6.8/18 black astening inspection X-EM6H, X-EW6H, X-E7H X-EM8H, X-EM10H, X-EW10H hnvs T rec ti hnvs Trec ti Nail standoff Tightening torque h NVS T rec astener [mm] [Nm] X-EM6H X-EM6H- / X-EW6H X-EM6H- / X-EW6H X-EW6H X-EW6H X-E7H Nail standoff Tightening torque h NVS T rec astener [mm] [Nm] X-EM8H X-EM8H X-EM10H X-EW10H / 13
Product data Dimensions. General information Material specifications. ➁ Threaded sleeve: S ➂ SN12-R washers: S 31635
X-BT stainless steel threaded studs Product data Dimensions X-BT W10-24-6 SN12-R X-BT M10-24-6 SN12-R 1 2 3 M10/ W10 24 [0.945"] 31.3 [1.232"] 4 X-BT W10-24-6-R X-BT M10-24-6-R 1 2 M10/ W10 26 [1.024"]
More informationX-U General Purpose Nails for Concrete and Steel
General Purpose Nails for Concrete and Steel Product data Dimensions MX 2.4 s o 4 P8 o 4 2.4 s General information Material specifications Carbon steel shank: HRC 58 HRC 59 ( 15) Zinc coating: 5 13 μm
More informationX-BT stainless steel threaded studs
X-BT stainless steel threaded studs Product data Dimensions X-BT W10-24-6 SN12-R X-BT M10-24-6 SN12-R 1 2 3 M10/ W10 24 [0.945"] 4 31.3 [1.232"] o 4.5 [0.177"] o 12 [0.472"] X-BT W6-24-6 SN12-R X-BT M6-24-6
More informationX-FCM Grating Fastening System
X-FCM X-FCM Grating Fastening System Product data Dimensions X-FCM 8.6 [0.339"] o 50 [.969"] o 8 [0.709"] o 0.3 [0.406"] 5 [0.97"] 9.5 [0.768"] L + 4 [0.57"] L. 5 6 [0.630"] [0.049"] 3 X-FCM-M_L General
More informationX-BT stainless steel threaded studs
X-BT stainless steel threaded studs Product data Dimensions X-BT W10-24-6 SN12-R X-BT M10-24-6 SN12-R 1 2 3 M10/ W10 24 [0.945"] 4 31.3 [1.232"] o 4.5 [0.177"] o 12 [0.472"] X-BT W6-24-6 SN12-R X-BT M6-24-6
More informationGeneral information Material specifications Carbon steel shank: HRC 58 Zinc coating: 8 16 µm Recommended fastening tools Single nail:
X-ENP Siding and Decking Nail Product data Dimensions Applications Examples General infmation Material specifications arbon steel shank: HR 58 Zinc coating: 8 16 µm Recommended fastening tools Single nail:
More informationX-HVB shear connectors
X-HVB shear connectors Product data Dimensions X-HVB 140 X-HVB 15.5 51 63 14.5 0.6 31.5 51 63 X-HVB 110 X-HVB 95 51 63 11.5 X-HVB 80 50 60 80 X-HVB 40 0.6 31 4.3 43 50 60 17.5 95 X-HVB 50 50 88 5 0.6 31
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 1: Direct Fastening, Edition 15.
The following excerpt are pages from the North American Product Technical Guide, Volume 1: Direct Fastening, Edition 15. Please refer to the publication in its entirety for complete details on this product
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2011 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationThe following excerpt are pages from the North American Anchor Fastening Technical Guide, 2011.
The following excerpt are pages from the North American Fastening Technical Guide, 2011. Contact Hilti s team of technical support specialists between the hours of 7:00am 6:00pm CST for complete details
More informationTrusted ICC ES HILTI, INC. Evaluation. report, or as to any. ICC-ES Evaluation
0 ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg Most Widely Accepted and Trusted ESR 2347 Reissued 12/2017 Revised 09/2018 This report is subject to renewal 12/2019.
More informationWedge Type Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE. Trubolt. Wedge Anchor ADVANTAGES
CONCRETE ANCHORING SPECIALISTS Dependable, Heavy-Duty, Inspectable, Wedge Type Expansion Anchor DESCRIPTION/SUGGESTED SPECIFICATIONS Wedge Type Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE Wedge anchors
More informationHilti X-BT Threaded Fastener Specification
Hilti X-BT Threaded Fastener Specification June 201 Contents Contents 1. Introduction page 4 1.1 Definitions and general terminology 4 1.2 The X-BT system 4 1.3 X-BT system features and benefits simplified
More informationDIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 42 6587 (562) 699 054 www.icc es.org ESR 247 Reissued 2/207 This report is subject to renewal 2/209. DIVISION: 05 00 00 METALS
More informationTECHNICAL MANUAL. MODIX Rebar Coupler Safe and Flexible Rebar Coupling System
TECHNICAL MANUAL MODIX Rebar Coupler Safe and Flexible Rebar Coupling System Version: PEIKKO GROUP 01/2016 MODIX Rebar Couplers Safe and flexible rebar splicing system Reduces congestion of reinforcement
More informationREPORT HOLDER: FASTENING SPECIALISTS, INC. 726 CENTRAL FLORIDA PARKWAY ORLANDO, FLORIDA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2328 Reissued 10/2017 This report is subject to renewal 10/2018. DIVISION: 03 00
More informationSpecification ZINC-NICKEL COATINGS WITH PASSIVATION JED ON FERROUS MATERIAL Passivation, Zn-Ni-steel
Specification 2015-11 Class: Surface protection Class No.:50 ZINC-NICKEL COATINGS WITH PASSIVATION JED ON FERROUS MATERIAL 739 Previous Edition Part name (for databases) 2014-03 Passivation, Zn-Ni-steel
More informationETA-11/0141 of 08/08/2016. European Technical Assessment. General Part. Technical Assessment Body issuing the. Instytut Techniki Budowlanej
INSTYTUT TECHNIKI BUDOWLANEJ PL 00-611 WARSZAWA ul. Filtrowa 1 tel.: (+48 22) 825-04-71 (+48 22) 825-76-55 fax: (+48 22) 825-52-86 www.itb.pl European Technical Assessment of 08/08/2016 General Part (English
More informationBonded Seals. Description
Description Bonded Seals represent a combination of metal washer and elastomer sealing lip vulcanised to the edge of the metal part to seal bolted connections and mounting elements in all industrial applications
More informationAnchor HSA Fastening. Technology Manual HSA. Stud anchor. Version /
Anchor HSA Fastening Stud anchor Technology Manual HSA Stud anchor Version 2015-09 09 / 2015 1 HSA Stud anchor Anchor version HSA Carbon steel with DIN 125 washe HSA-R Stainless steel A4 HSA-R2 Stainless
More informationHilti X-GR, X-GR RU, X-FCM grating fasteners. Securely fastened. In seconds! Hilti. Outperform. Outlast.
Securely fastened. In seconds! Hilti. Outperform. Outlast. Applications Fastening grating on steel structures for all types of facilities: refineries, chemical plants, offshore platforms, civil and industrial
More informationFROM: SUBJECT: HILTI X-ENP-19, X-HSN 24 or X-U POWDER-ACTUATED FASTENER SUBSTITUTION REQUEST
DATE: PROJECT: TO: FROM: SUBJECT: HILTI X-ENP-19, X-HSN 24 or X-U POWDER-ACTUATED FASTENER SUBSTITUTION REQUEST SPECIFICATION TITLE: SECTION: PAGE: ARTICLE/PARAGRAPH: DESCRIPTION: DESIGN DETAIL NO.: PROPOSED
More informationEnglish translation prepared by DIBt Original version in German language
Date: Reference: 11/11/2013 I 36-1.14.4-103/13 English translation prepared by DIBt Original version in German language Approval number: Validity Z-14.4-456 from: 11 November 2013 Applicant: Hilti Deutschland
More informationDIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 100 PLANO, TEXAS 75024
0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-2347 Reissued 12/2015 This report is subject to renewal 12/2017. DIVISION: 05 00 00 METALS SECTION:
More informationWARSAW ul. FILTROWA 1 phone: (48 22) , (48 22) fax: (48 22)
LOGO ITB Instytut Techniki Budowlanej (Building Research Institute) 00-611 WARSAW ul. FILTROWA 1 phone: (48 22) 825 04 71, (48 22) 825 76 55 fax: (48 22) 825 52 86 Member of the European Union for Technical
More informationSVM-PSC Polyester resin for use in concrete
SVM-PSC Polyester resin for use in concrete Bonded anchor with anchor rod made of galvanized steel or stainless steel of sizes M8 to M30 for use in non-cracked concrete Basic product information Features
More informationDesignated according to Article 29 of Regulation (EU) No 305/2011 and member of EOTA (European Organisation for Technical Assessment)
INSTYTUT TECHNIKI BUDOWLANEJ PL 00-611 WARSZAWA ul. Filtrowa 1 tel.: (+48 22) 825-04-71 (+48 22) 825-76-55 fax: (+48 22) 825-52-86 www.itb.pl Designated according to Article 29 of Regulation (EU) No 305/2011
More informationHilti X-EGN Nails. Submission Folder
Submission folder Hilti X-EGN Nails Submission Folder Sample Submission and Approval Form 2-3 Product Information 4-8 Technical Information 9-13 Government Letter Building Department 14-15 Country of Origin
More informationHollo-Bolt. Hollo-Bolt by Lindapter. Hollo-Bolt Options
Hollo- by Lindapter 37 Hollo- by Lindapter Installation is quickly carried out by inserting into pre-drilled steel and tightening with a torque wrench. Independent approvals include ICC-ES seismic accreditation,
More informationPRODUCT DATA SHEET SAFETY BOLT
S SK B S A4 SK A4 B A4 PRODUCT DATA SHEET SAFETY BOLT LEGENDARY TWIN-CONE HEAVY DUTY ANCHOR FOR HI-POWER PERFORMANCE www.sormat.com facebook.com/sormat youtube.com/sormatfixing 1 Legendary twin-cone heavy
More informationPROJECT SUBMITTAL. Power-Stud TM. Wedge Expansion Anchor PROJECT SUBMITTAL CONTENTS APPROVALS AND LISTINGS
PROJECT SUBMITTAL Power-Stud TM Wedge Expansion Anchor Anchoring into Solid Concrete and Masonry Base Materials Anchor Diameter is the Same as the Hole Diameter Interlocking Clip Wedges Prevent Anchor
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC. EVALUATION SUBJECT: KWIK BOLT TZ MASONRY ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 4 687 (6) 699 04 www.icc es.org ESR 78 Reissued 07/018 This report is subject to renewal 07/019. DIVISION: 04 00 00 MASONRY
More informationR-CAS-V Spin-In Capsule with Threaded Rods
R-CAS-V Spin-In Capsule with Threaded Rods High-performance, quick-setting, styrene-free vinylester resin for concrete Approvals and Reports ETA-10-0108 Product information Features and benefits Approved
More informationSINGLE ANCHOR USE FOR NON-CRACKED CONCRETE
LA+ LAL+ PRODUCT DATA SHEET DROP IN ANCHORS SINGLE ANCHOR USE FOR NON-CRACKED CONCRETE www.sormat.com facebook.com/sormat youtube.com/sormatfixing 1 ETA-approved drop in anchors ideal for suspension systems
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2254 Reissued 12/2017 This report is subject to renewal 12/2019. DIVISION: 03 00
More informationSIMPLY THE BEST HEAVY DUTY SELF-UNDERCUTTING ANCHOR IN THE WORLD
BLS BLS-P BLS A4 SD ILS LPA A4 PRODUCT DATA SHEET SUPERPLUS UNDERCUT ANCHORS SIMPLY THE BEST HEAVY DUTY SELF-UNDERCUTTING ANCHOR IN THE WORLD www.sormat.com facebook.com/sormat youtube.com/sormatfixing
More informationHKD redundant FLUSH ANCHOR. Technical Datasheet Update: Mar-18
HKD redundant FLUSH ANCHOR Technical Datasheet Update: Mar-18 HKD Flush anchor Everyday standard manual set flush anchor for redundant fastening applications Anchor version HKD (M6-M16) HKD-woL (M6-M16)
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
ttached are page(s) from the 2011 Hilti North merican Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation, corrosion,
More informationPRODUCT DATA SHEET THROUGH BOLTS. facebook.com/sormat youtube.com/sormatfixing SORMAT Product data sheet 1217
S-KA S-KAK S-KAH A4 S-KAH HCR S-KAR A2 S-HHA A2 PRODUCT DATA SHEET THROUGH BOLTS www.sormat.com facebook.com/sormat youtube.com/sormatfixing 1 Premium-quality through bolts for fixing in cracked and non-cracked
More informationHigh Performance Thread Rolling Screw for Metal
High Performance Thread Rolling Screw for Metal Features / Benefits ROLOK thread rolling fasteners for metals offer a unique spiral thread form to achieve excellent drive-to-strip performance in many challenging
More informationl MATERIAL SPECIFICATIONS
SECTION 4.5 PAGE 1 / 5 l DESCRIPTION The UCAN Scru-it masonry anchor is manufactured to strict specifications from high quality steel. The proprietary, UCAN designed, scalloped thread cuts deep grooves
More informationBlue Banger Hanger Cast-In-Place, Internally Threaded Insert. Mechanical Anchors. Cracked. Concrete. Features. Installation. Installation Sequence
Blue Banger Hanger Cast-In-Place, Internally Insert Wood-Form Insert Multi-thread, cast-in-place wood-form and metal-deck inserts for cracked and uncracked concrete maximize jobsite efficiency and reduce
More informationHilti S-BT Screw-in threaded studs. Specifications
Hilti S-BT Screw-in threaded studs January 2017 Content 1 Introduction 5 1.1 Definition 5 1.2 The S-BT system 5 1.2.1 S-BT fastener and designation 5 1.2.2 Drilling tool 6 1.2.3 Stepped drill bit 6 1.2.4
More informationDesignated according to Article 29 of Regulation (EU) No 305/2011 and member of EOTA (European Organisation for Technical Assessment)
INSTYTUT TECHNIKI BUDOWLANEJ PL 00-611 WARSZAWA ul. Filtrowa 1 tel.: (+48 2 825-04-71 (+48 2 825-76-55 fax: (+48 2 825-52-86 www.itb.pl Designated according to Article 29 of Regulation (EU) No 305/2011
More informationPage 9 of European Technical Approval ETA-10/0280 Marking: Marking: Identifying Identifying mark: mark: Anchor Anchor identity: identity: Category Category: : S KA H (stainless steel) K (hot dip galvanized)
More informationConcrete Screw-Anchors
Screw-Anchors Screw-Anchor are a totally removable rotation setting, thread forming anchor, ideal for either temporary or permanent anchoring into substrates such as concrete, brick, hollow brick or block.
More informationSTAINLESS STEEL. Useful Information
STAINLESS Useful Information STAINLESS Useful Information Stainless Steel Grades - Chemical Composition (BS EN ISO 3506-1:2009 / BS EN ISO 3506-2:2009) NOTE 1 A description of the groups and grades of
More informationULTRAPLUS M12-M36. The undercut anchor for exceptionally high loads in cracked and non-cracked concrete also for shock and seismic loads.
ULTRAPLUS M12-M36 The undercut anchor for exceptionally high loads in cracked and non-cracked concrete also for shock and seismic loads. FUNCTION When the anchor is installed the expansion segments are
More informationEuropean Technical Assessment. ETA-17/0237 of 15/05/2017. General Part. Technical Assessment Body issuing the. Instytut Techniki Budowlanej
INSTYTUT TECHNIKI BUDOWLANEJ PL 00-611 WARSZAWA ul. Filtrowa 1 tel.: (+48 22) 825-04-71 (+48 22) 825-76-55 fax: (+48 22) 825-52-86 www.itb.pl Designated according to Article 29 of Regulation (EU) No 305/2011
More informationSUPERPLUS M8-M16. The undercut fixing system that does not require a special setting tool. FUNCTION BENEFITS
SUPERPLUS M8-M16 The undercut fixing system that does not require a special setting tool. FUNCTION Automatic self-undercutting. The unique design of the SUPERPLUS causes an undercut to be created when
More informationPage 9, issued on 03. February 2009 Threaded rod M8, M10, M12, M16, M20, M24, M27, M30 with washer and hexagon nut L df h h ef 0 tfix h min Reinforcing bar 8, 10, 12, 14, 16, 20, 25, 28, 32 acc. to Annex
More informationHDA-P HDA-PR HDA-PF Anchor for presetting. HDA-T HDA-TR HDA-TF Anchor for through-fasting. Nuclear power plant approval
HDA Design anchor Anchor version HDA-P HDA-PR HDA-PF Anchor for presetting HDA-T HDA-TR HDA-TF Anchor for through-fasting Benefits - suitable for non-cracked and cracked concrete C 20/25 to C 50/60 - mechanical
More informationEJOT Through Bolts. Premium-quality through bolts for fixing in cracked and non-cracked concrete.
EJOT Premium-quality through bolts for fixing in cracked and non-cracked concrete www.ejot.com Anchors and Instaation Technology Premium-quality through bolts for fixing in cracked and non-cracked concrete
More informationPRODUCT DATA SHEET THROUGH BOLTS S-KA S-KAK S-KAH A4 S-KAH HCR S-KAR A2 HHA A2
S-KA S-KAK S-KAH A4 S-KAH HCR S-KAR A2 HHA A2 PRODUCT DATA SHEET THROUGH BOLTS www.sormat.com facebook.com/sormat youtube.com/sormatfixing SORMAT SORMAT PDS-S-KA-EN-2018-05-03 1 Premium-quality through
More informationHalliburton. All rights reserved. Flange Integrity Management
Flange Integrity Management Flange Integrity Management Why? North America Pressure Vessel Research Council found that each process facility in North America experienced 180 leaks per year, six of which
More informationR-CAS-V Spin-In Capsule with Threaded Rods
R-CAS-V Spin-In Capsule with Threaded Rods High-performance, quick-setting, styrene-free vinylester resin for concrete Approvals and Reports ETA-10-0108 Product information Features and benefits Approved
More informationWedge Anchor B Steel, zinc plated
Wedge Anchor for noncracked concrete Wedge Anchor Steel, zinc plated Range of loading: kn 3,2 kn Range of concrete quality: C/25 C/0 Approvals and Certificates Description The tried and tested wedge anchor
More informationMaterials Polyester Resin Anchors: Carbon Steel grade 5.8 Stainless Steel: AISI 316
Chemset Injection is a two component polyester resin anchor system in a coaxial cartridge with mixing nozzle. Developed for fixing awkward materials in hollow and solid sections where access may be difficult.
More informationSIMPSON STRONG-TIE BOTTOM PLATE ANCHOR SOLUTIONS. Product. Scope. Building Regulations. Appraisal No. 983 [2018] Appraisal No.
SIMPSON STRONG-TIE BOTTOM PLATE ANCHOR SOLUTIONS BRANZ Appraisals Technical Assessments of products for building and construction. Simpson Strong-Tie New Zealand Ltd 52A Arrenway Drive Albany Auckland
More informationREPORT HOLDER: GRABBER CONSTRUCTION PRODUCTS, INC. EVALUATION SUBJECT: GRABBER FASTENERS FOR USG STRUCTURAL PANELS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4223 Issued 07/2018 This report is subject to renewal 07/2019. DIVISION: 05 00 00
More informationFROM: PROPOSED SUBSTITUTION: Use HILTI X-CW Ceiling Wire for Suspended Ceiling Systems
DATE: PROJECT: TO: FROM: SUBJECT: HILTI X-CW CEILING WIRE FASTENER SUBSTITUTION REQUEST SPECIFICATION TITLE: SECTION: PAGE: ARTICLE/PARAGRAPH: DESCRIPTION: DESIGN DETAIL NO.: PROPOSED SUBSTITUTION: Use
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2008 Hilti North American Product Technical Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationULTRAPLUS M12-M36. The undercut anchor for exceptionally high loads in cracked and non-cracked concrete also for shock and seismic loads.
ULTRAPLUS M12-M36 LIEBIG The ORIGINAL Anchoring Technology The undercut anchor for exceptionally high loads in cracked and non-cracked concrete also for shock and seismic loads. FUNCTION When the anchor
More informationSECTION COLD-FORMED METAL TRUSSES
SECTION 054400 COLD-FORMED METAL TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationHSA Carbon steel with DIN 125 washer. HSA-R Stainless steel A4 with DIN 125 washer. HSA-R2 Stainless steel A2 with DIN 125 washer
Anchor version Benefits HSA Carbon steel with DIN 125 washer HSA-R Stainless steel A4 with DIN 125 washer HSA-R2 Stainless steel A2 with DIN 125 washer HSA-BW Carbon steel with DIN 9021 washer HSA-F Carbon
More informationHILTI HSC UNDERCUT ANCHOR. Technical Datasheet Update: Sep-18
HILTI HSC UNDERCUT ANCHOR Technical Datasheet Update: Sep-18 Du HSC få Undercut anchors Ultimate-performance undercut anchor for shallow embedment depth Anchor version R (M8-M12) R (M6-M12) Benefits -
More informationProduct Range. with Technical Data.
Product Range 2013 with Technical Data www.mkt.de All technical details may be subject to change without notice. We do not accept liability for printing mistakes or omissions. For the latest technical
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.1.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.1. Please refer to the publication in its entirety for complete details on this product
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 2 687 (62) 699 0 www.icc es.org ESR 067 Reissued 06/208 This report is subject to renewal 06/209. DIVISION: 0 00 00 CONCRETE
More informationDrop-in Anchor E / ES Steel, zinc plated
Drop-in Anchor for non-cracked concrete and multiple use in cracked and non-cracked concrete Drop-in Anchor E / ES Steel, zinc plated Drop-in Anchor E Range of loading:,2 kn - 28,6 kn Range of concrete
More informationDrop-in Anchor E / ES Steel, zinc plated
Drop-in Anchor for non-cracked concrete and multiple use in cracked and non-cracked concrete Drop-in Anchor E / ES Steel, zinc plated Drop-in Anchor E Range of loading:,2 kn - 28,6 kn Range of concrete
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17.
The following excerpt are pages from the North merican Product Technical Guide, Volume 2: nchor Fastening, Edition 17. Please refer to the publication in its entirety for complete details on this product
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.
The following excerpt are pages from the North merican Product Technical Guide, Volume 2: nchor Fastening, Edition 16. Please refer to the publication in its entirety for complete details on this product
More informationDIVISION: CONCRETE SECTION: CAST IN CONCRETE ANCHORS SECTION: CONCRETE ANCHORS REPORT HOLDER: DEWALT
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3657 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 03 00
More informationFROM: PROPOSED SUBSTITUTION: Use HILTI X-U instead of fillet weld or arc spot puddle weld
DATE: PROJECT: TO: FROM: SUBJECT: HILTI X-U POWDER-ACTUATED FASTENER SUBSTITUTION REQUEST SPECIFICATION TITLE: SECTION: PAGE: ARTICLE/PARAGRAPH: DESCRIPTION: DESIGN DETAIL NO.: PROPOSED SUBSTITUTION: Use
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: BORAL COMPOSITES, INC.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3597 Reissued 05/2018 This report is subject to renewal 05/2019. DIVISION: 07 00
More informationFINISH SPECIFICATIONS FOR PIERCE NUTS & PIERCE STUDS DETAILED FINISH DESCRIPTIONS AND REQUIREMENTS
FINISH SPECIFICATIONS FOR PIERCE NUTS & PIERCE STUDS DETAILED FINISH DESCRIPTIONS AND REQUIREMENTS S S300 S301 S302 S303 PLAIN- NO SUPPLEMENTARY FINISH REQUIRED OTHER THAN THE FINISH CONSIDERED THE NORMAL
More informationLEGACY REPORT ER-5608* Reissued February 1, Legacy report on the 1997 Uniform Building Code
LEGACY REPORT ER-5608* Reissued February 1, 2004 www.icc-es.org Business/Regional Office 5360 Workman Mill Road, Whittier, California 90601 (562) 699-0543 Regional Office 900 Montclair Road, Suite A, Birmingham,
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 ICC ES Report ICC ES (00) 7 () 0 www.icc es.org 000 Most Widely Accepted and Trusted ESR 70 Reissued 0/0 This report is subject to renewal 0/0. DIVISION: 0 00 00 CONCRETE SECTION: 0 00 CONCRETE ANCHORS
More informationESR ICC Evaluation Service, Inc. Reissued July 1, 2006 This report is subject to re-examination in two years.
ESR-1178 Reissued July 1, 2006 This report is subject to re-examination in two years. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California
More informationDECLARATION OF PERFORMANCE according to Annex III of the Regulation (EU) Nr. 305/2011 (Construction Products Regulation)
EN DECLARATION OF PERFORMANCE according to Annex III of the Regulation (EU) Nr. 305/2011 (Construction Products Regulation) Hilti nailed shear connector HVB with powder-actuated fastener X-ENP-21 HVB No.
More informationSTRUT METAL FRAMING SYSTEMS
STRUT METAL FRAMING SYSTEMS CONTENTS STRUT CHANNELS 2 FLAT PLATE FITTINGS 4 ANGLE FITTINGS 6 Z & U FITTINGS 8 BEAM CLAMPS 9 BASE POSTS 11 CANTILEVERS 13 I-BEAM SUPPORTS 15 PROPERTIES OF SECTION PROFILES
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3576 Reissued 07/2017 This report is subject to renewal 07/2018. DIVISION: 03 00
More informationDeclaration of Performance
Declaration of Performance 1343-CPR-M 530-11/01.15 1. Unique identification code of the product-type: Bonded injection type anchor Mungo MIT Tropical and MIT- VE Plus for use in non-cracked concrete 2.
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 687 (6) 699 0 www.icc es.org ESR 8 Reissued 0/08 This report is subject to renewal 0/09. DIVISION: 0 00 00 MASONRY SECTION:
More informationHDA UNDERCUT ANCHOR. Technical Datasheet Update: Dec-17
HDA UNDERCUT ANCHOR Technical Datasheet Update: Dec-17 HDA Undercut anchor Ultimate-performance undercut anchor for dynamic loads Anchor version HDA-P HDA-PR HDA-PF Anchor for pre-setting (M10-M20) HDA-T
More informationMaterials Carbon Steel and Malleable Iron are used in the manufacture of concrete inserts. Stainless Steel and other materials are available.
Concrete inserts offered in this section are designed to provide a pre-set support point in concrete ceilings, walls, and floors. A range of inserts with varying design loads are available. Materials Carbon
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3531 Reissued 04/2018 This report is subject to renewal 04/2019. DIVISION: 06 00
More informationEnglish translation prepared by CSTB - Original version in French language
Member of Centre Scientifique et Technique du Bâtiment 84 avenue Jean Jaurès CHAMPS-SUR-MARNE F-77447 Marne-la-Vallée Cedex 2 www.eota.eu Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 European Technical
More informationHLC. Hex head nut with pressed-on washer HLC-H. Bolt version with washer HLC-L. Torx round head HLC-SK. Torx Counter sunk head HLC-EC
HLC Anchor version Hex head nut with pressed-on washer Benefits HLC offers various head shapes and fastening thicknesses. HLC-H Bolt version with washer HLC-L Torx round head HLC-SK HLC-EC HLC-EO HLC-T
More informationInjection Adhesive VM-PY
Cartridge VM-PY 410 Coaxial cartridge Content: 410ml Range of loading: 0,3 kn - 39,4 kn Concrete quality: C20/25 - C50/60 Masonry: Solid brick, Hollow block Description The Injection Adhesive is a polyester-resin
More informationICC-ES Evaluation Report Issued August 1, 2011 This report is subject to renewal in one year.
ICC-ES Evaluation Report ESR-3032 Issued August 1, 2011 This report is subject to renewal in one year. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council DIVISION:
More informationHSC UNDERCUT ANCHOR. Technical Datasheet Update: Jul-18
HSC UNDERCUT ANCHOR Technical Datasheet Update: Jul-18 Du HSC få Undercut anchors Ultimate-performance undercut anchor for shallow embedment depth Anchor version R (M8-M12) R (M6-M12) Benefits - The perfect
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2966 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 04 00
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16. Please refer to the publication in its entirety for complete details on this product
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3931 Reissued 07/2017 This report is subject to renewal 07/2019. DIVISION: 03 00
More information