Thick film rectangular
|
|
- Aron Stone
- 6 years ago
- Views:
Transcription
1 Thick film rectangular (212 size : 1 / 8W)!Features 1) Power rating of 1 / 8W 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Leading the world in development and mass production. Since start of production in 1982 (first in the wold), this component has established a solid reputation as a general purpose chip resistor. 5) ROHM resistors have approved ISO 91 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it.!ratings Item Conditions Specifications Rated power Power must be derated according to the power derating curve in Figure 1 when ambient exceeds 7 C W (1 / 8W) at 7 C POWER LOAD (%) AMBIENT TEMPERATURE ( C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E= P R E: Rated voltage (V) P: Rated power (W) R: Nominal resistance (Ω) Limiting element voltage Max. overload voltage 15V 2V Nominal resistance See Table 1. Operating 55 C C
2 Jumper type Table 1 Resistance Rated current Operating 2A 55 C to +155 C Resistance tolerance F (±1%) Resistance range (Ω) Resistance coefficient (ppm/ C).1 R <.15 (E24) 4±2.15 R < 1 (E24) ±25 1 R 2.2M (E24,96) ±1 J (±5%).1 R <.15 (E24) 4±2.15 R < 1 (E24) ±25 R < 2.2 (E24) 5± R < 1 (E24) ±5 1 R 1M (E24) ±2!Before using components in circuits where they will be exposed to transients such as pulse loads (short duration, high level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.!characteristics Resistance Guaranteed value Item Test conditions (JIS C 521-1) Resistor type Jumper type Variation of resistance with J : ±5% F : ±1% See Table.1 Overload ± (%+.1Ω) JIS C JIS C Measurement : 55 / +25 / +125 C JIS C Rated voltage (current), 2s. Maximum overload voltage : 2V Solderability Resistance to soldering heat Rapid change of Damp heat, steady state Endurance at 7 C Endurance Resistance to solvent Bend strength of the end face plating ± (%+5Ω) No remarkable abnormality on the appearance. ± (%+5Ω) ± (%+.1Ω) ± (%+.1Ω) ± (%+.1Ω) ± (%+5Ω) A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (%+5Ω) Without mechanical damage such as breaks. JIS C Rosin Ethanol (25%WT) Soldering condition : 235±5 C Duration of immersion : ±s. JIS C Soldering condition : 26±5 C Duration of immersion : 1±1s. JIS C Test temp. : 55 C~+125 C 5cyc JIS C C, 93%RH Test time : 1,h~1,48h JIS C Rated voltage (current), 7 C h : ON h : OFF Test time : 1,h~1,48h JIS C C Test time : 1,h~1,48h JIS C ±5 C, Immersion cleaning, 5±min. Solvent : 2-propanol JIS C
3 !External dimensions (Units : mm) 1.4± No. Material.4±.2 ±.1 5 5± Resistive element (Oxide metal thick film) Silver palladium thick film electrode Nickel electrode 4 Sn/Pb or Sn electrode 5 Alumina substrate 1.25±.1 6 Overcoating (glass) 6!Packaging Reel Taping P P2 P1 φd E F W B A B D A Thick paper mount Heat crimp cover/tape (Underside paper tape) Chip resistor Square punchout hole T2 C Label A B C D φ18 3 φ φ13±.2 EIAJ ET-72A compliant Bulk case φ W F E A B 8.±.3 3.5±5 1.75± D P P1 P2 T2 ±.1 ±.1 ±5 Max. 1.1 Shutter Slider 12± EIAJ ET-721A compliant 11±.7
4 !Part designation Part No. 3-digit or 4-digit IEC coding system Nominal resistance Packaging / Processing specifications Resistance tolerance Special part number Part No. Code EZH PZHI Packaging Paper tape Bulk case Standard ordering Unit(pcs) 5, 1, F ±1% J ±5% Specify "J" for jumper also. 1Ω or more (F class) Blank 1Ω or more (J class) Up to1ω (F class) L Up to1ω (J class)!dimensions JIS C JIS C JIS C LENGTH (mm) WIDTH (mm) THICKNESS (mm) Fig.2 Dimensions (length) Fig.3 Dimensions (width) Fig.4 Dimensions (thickness)!electrical characteristics DC RESISTANCE (%) JIS C C 65%RH TEMPERATURE COEFFICIENT (ppm/ C) JIS C C / 55 C 25 C / 125 C JIS C RATED VOLTAGE TIMES : 2s MAXIMUM OVERLOAD VOLTAGE : 2V Fig.5 Resistance Fig.6 Variation resistance with Fig.7 Overload
5 JIS C SOLDERING CONDITION : 26 C 1s JIS C C / 125 C 5cyc JIS C C 93%RH WITH NO LOAD 1,h k 1k 1k1M 1M k 1k 1k1M 1M Fig.8 Resistance to soldering heat Fig.9 Rapid change of Fig.1 Damp heat, steady state JIS C C 1,h OVERLOAD : THE RATED VOLTAGE JIS C C WITH NO LOAD 1,h JIS C IPA, 5min. Fig.11 Endurance at 7 C Fig.12 Endurance Fig.13 Resistance to solvents JIS C ENDURANCE WITH 9mm WIDTH Fig.14 Bend strength of the end face plating
1/2W, 0612 Low Resistance Chip Resistor (Lead / Halogen Free)
1/2W, 0612 (Lead / Halogen Free) 1. Scope This specification applies to 1.6mm x 3.2mm size 1/2W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation RL1632W
More information1/2W, 0805 Low Resistance Chip Resistor (Lead / Halogen free)
1. Scope 1/2W, 0805 (Lead / Halogen free) This specification applies to 1.2mm x 2.0mm size 1/2W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation RL
More informationGeneral Purpose Chip Resistors MCMR Series
Description The resistors are constructed in a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste that is applied to the top surface
More informationSulfur tolerant chip resistors
Sulfur tolerant chip resistors TRR series Datasheet Features 1)Special construction prevents sulfur gas penetration, significantly increasing reliability. 2)ROHM resistors have obtained ISO91 / ISO / TS16949
More informationCal-Chip Electronics, Incorporated Thick Film Chip Resistors - RM Series
Thick Film Chip Resistors - RM Series Fixed Chip Resistors manufactured for more compact electronic components and automatic mounting system. These Chip Resistors have electrical stability and mechanical
More informationDatasheet RS Pro RS Series Thick Film Surface Mount Resistor 0603 Case 330Ω ±5% 0.1W ±200ppm/ C RS Stock No:
Datasheet RS Pro RS Series hick Film Surface Mount Resistor 0603 Case 330Ω ±5% 0.1 ±200ppm/ C RS Stock No: 713-4129 Product Details RS Pro 0603 thick film surface mount resistor with ±5% tolerance, provides
More informationAnti-surge chip resistors
Anti-surge chip resistors ESR series Datasheet Features 1)Exclusive resistive element pattern and laser trimming technology results in significantly improved surge resistance characteristics. 2)2kV to
More informationHigh power chip resistors < Wide terminal type > LTR series
High power chip resistors < Wide terminal type > LTR series Features 1)High joint reliability with long side terminations. 2)Highest power ratings in their class. 3)Guaranteed anti-surge characteristic
More informationLow ohmic thick film chip resistors
Low ohmic thick film chip resistors MCR series - low ohmic - Features 1)Very-low ohmic resistance from 47mΩ is in lineup by thick-film resistive element. 2)ROHM resistors have obtained ISO91 / ISO / TS16949
More informationG M R H T B F A
High power low ohmic chip shunt resistors GMR series Features 1)High power (3W to 5W ) 2)High heat dissipation 3)Excellent TCR characterristics 4)Low ohmic (5mΩ to 220mΩ) Products list Part No. Size (mm)
More informationDatasheet RS Pro RS Series Axial Carbon Resistor 1kΩ ±5% 2W ppm/ C RS Stock No:
Datasheet RS Pro RS Series Axial Carbon Resistor 1kΩ ±5% 2W -500 +350ppm/ C RS Stock No: 707-8861 Product Details RS Pro axial carbon resistor with ±5% tolerance, provides 1 kω resistance and is power
More informationUltra-low ohmic chip resistors for current detection
Ultra-low ohmic chip resistors for current detection PMR series Features 1)Ultra low-ohmic resistance range (1mΩ ~ ) 2)Improved current detection accuracy by trimming-less structure. 3)Special low resistance
More informationCarbon film resistors
Carbon film resistors (6.3 φ 2.4 size: 1 / 3W) ROHM resistors are produced using an integrated production system for parts and materials, and state of the art technology to ensure high precision productivity,
More informationUltra-low ohmic jumper chip resistors PMR series - jumper type -
Ultra-low ohmic jumper chip resistors PMR series - jumper type - Datasheet Features 1) Metallic resistive element utilized for extremely low conduction resistance. (.5mΩMax.) 2) High current capability.
More information< Specifications (Precautions and Prohibitions) >
FIXED THICK FILM CHIP RESISTORS Series SPECIFICATION PRODUCTS: FIXED THICK FILM CHIP RESISTORS 1/14 TYPE: MCR01 MRT SERIES ROHM CO., LTDRESISTOR DIV FIXED THICK FILM CHIP RESISTORS Series < Specifications
More informationHigh Stability Resistor Chips (< 0.25 % at Pn at 70 C during 1000 h) Thick Film Technology
High Stability Resistor Chips (< 0.25 % at Pn at 70 C during 0 h) Thick Film Technology thick film resistor chips are specially designed to meet very stringent specifications in terms of reliability, stability
More informationResistance Tolerance Code F J. Tolerance ± 1% ± 5% Jumper
42, 63, 85, 126, 121, 1812, 21, 2512 : ERJ S2, S3, S6, S8, S14 S12, S1D, S1T Anti-Sulfurated Thick ilm Chip Resistors eatures Special construction to avoid open failure due to the presence of sulfur High
More informationHigh Temperature (245 C) Thick Film Chip Resistor
High Temperature (245 C) Thick Film Chip Resistor For applications such as down hole applications or aircraft breaking systems, the need for parts able to withstand very severe conditions (temperature
More informationDATA SHEET Metal Element Current Sensing Chip Resistor CLS Series
DATA SHEET Metal Element Current Sensing Chip Resistor 0.5% TO 5%, TCR ±25 TO ±450 SIZE: 1206/2010/2512/2725/2728/4527/4527S RoHs Compliant 14 October, 2016 V.4 DS-ENG-007 23 Page: 2 of 1. SCOPE 1.1 This
More informationM16 M20 M25 M207 M51 M100 M200
Metal Film Fixed Resistor Specifications Per IEC 60115-1 MIL-R-10509 d L H D Features Conformal multi-layer coating Color code per MIL & EIA standards Special tin-plated electrolytic copper lead wire Products
More informationMMP - Metal Film MELF
Specifications Per IEC 60115-1, IEC 60115-2 EN140401-803 B L D Features SMD enabled structure Excellent solderability termination Products meet RoHS requirements and do not contain substances of very high
More informationReference Only. 2.Part Numbering (ex) NF Z 5B BW 2R9 L N 1 0 L
SpecNo.JENF243J-0011A-01 P1/10 CHIP NOISE FILTER NFZ5BBW LN10 REFERENCE SPECIFICATION 1.Scope This reference specification applies to NFZ5BBW_LN10L Series, Chip Noise Filter. 2.Part Numbering (ex) NF Z
More informationSurface Mount Sense Resistors
Resistors Surface Mount Flexible leads for thermal expansion Open-air design reduces PCB heating Values down to 1milliohm Element TCR ±2ppm/ C Zero-ohm 65A jumper version RoHS compliant All parts are Pb-free
More information20 W Power Resistor, Thick Film Technology, TO-220
20 W Power Resistor, Thick Film Technology, TO-220 DESIGN SUPPORT TOOLS Models Available click logo to get started The well known TO-220 package is compact and easy to mount. DIMENSIONS in millimeters
More information(RE) Ultra Precision Resistors. Token Electronics Industry Co., Ltd. Version: January 13, Web:
Version: January 13, 2017 (RE) Ultra Precision Resistors Token Electronics Industry Co., Ltd. Web: www.token.com.tw Email: rfq@token.com.tw Taiwan: No.137, Sec. 1, Zhongxing Rd., Wugu District, New Taipei
More informationESCC ( ) 4001/023 Qualified High Precision (5 ppm, 0.01 %), Thin Film Chip Resistors
( ) 4001/023 Qualified High Precision (5 ppm, 0.01 %), Thin Film Chip Resistors DESIGN SUPPORT TOOLS Models Available click logo to get started Thin Film division holds QML qualification ( technology flow
More information1-8M CMF F T-1 R36 HISTORICAL MODEL RESISTANCE VALUE TOLERANCE CODE TEMP. COEFFICIENT PACKAGING
CMF Industrial Metal Film Resistors, Industrial FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics Exceptionally
More informationPrecision Thick Film Chip Resistors ERJ G: 0201 ERJ R: 0402, 0603, 0805 ERJ E : 0603, 0805, 1206, 1210, 1812, 2010, 2512
Precision Thick Film Chip esistors J G: J : 4, 6, 5 J : 6, 5, 6,,,, 5 Type: J G J,, 6 J, 6,, 4,, T n Features l Small size and lightweight For PCB size reduction and lightweight products l High reliability
More informationMetal Film Resistors, Industrial, Precision
Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Available Excellent high frequency characteristics Exceptionally
More information(EE) Low TCR Metal Film Resistors
Version: March 1, 2017 Electronics Tech. (EE) Low TCR Metal Film Resistors Web: www.direct-token.com Email: rfq@direct-token.com Direct Electronics Industry Co., Ltd. China: 12F, Zhong Xing Industry Bld.,
More informationReference Only. Spec. No. JENF243D-0006K-01 P 1/ 8
Spec. No. JENF243D-0006K-01 P 1/ 8 Chip EMIFIL LC Combined Monolithic NFL21SP X1C Reference Specification 1. Scope This reference specification applies to Chip EMIFIL LC Combined Monolithic Type NFL21S
More informationCommercial Thin Film Chip Resistor, Surface Mount Chip
Commercial Thin Film Chip Resistor, Surface Mount Chip PTN Actual Size 1505 These chip resistors are available in both top side and wraparound termination styles in a variety of sizes. They incorporate
More informationHigh Pulse, Fusible, Non-Inductive, Flameproof, Metal Film Resistor
High Pulse, Fusible, Non-Inductive, Flameproof, Metal Film Resistor FEATURES Designed to meet UL1412 safety requirements Defined fusing characteristics Inherent non-inductive design Superior surge handling
More informationReference Only. Chip Ferrite Bead BLM31 SZ1 Murata Standard Reference Specification [AEC-Q200]
P.1/9 Chip Ferrite Bead BLM31 SZ1 Murata Standard Reference Specification [AEC-Q200] 1. Scope This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM31_SZ Series based
More informationnicrom e l e c t r o n i c
G E N E R A L High Performance Thick Film Resistors C A T A L O G 3 Nicrom Electronic Via Roncaglia CH - 6883 Novazzano SWITZERLAND Phone : ++4 () 9 68 99 86 Fax : ++4 () 9 68 99 86 info@nicrom-electronic.com
More informationMold Military-Qualified Resistive Precision Resistor (RN)
Version: January 13, 2017 Mold Military-Qualified Resistive Precision Resistor (RN) Token Electronics Industry Co., Ltd. Web: www.token.com.tw Email: rfq@token.com.tw Taiwan: No.137, Sec. 1, Zhongxing
More informationApproval Sheet. for. Metal Oxide Film Resistors Power & Flame-Proof Type. MOF series YAGEO CORPORATION
Approval Sheet for Metal Oxide Film Resistors Power & Flame-Proof Type MOF series ±2% & ±5% YAGEO CORPORATION Headquarters: 3F, No.233-1, Pao Chiao Rd., Xindian, Taipei, Taiwan, R.O.C. Tel: 886-2-6629-9999
More informationReference Only. Spec. No. JENF243E-0002Q-01 P1 / 8
Spec. No. JENF243E-0002Q-01 P1 / 8 Chip EMIFIL LC Combined Type for Large Current NFE31PT 1E9 Reference Specification 1. Scope This reference specification applies to Chip EMIFIL LC Combined Type for Large
More informationResistance Tolerance Code J. Marking. Value Marking on Y black side Nil No marking. Resistance Value
Thick Film Chip Resistors 15, 21, 42, 63, 85, 126, 121, 1812, 21, 2512 : R XG, 1G, 2G, 3G, 6G, 8G, 14, 12, 12Z, 1T Features Small size and lightweight High reliability Metal glaze thick fi lm resistive
More informationNTC Type SMD. Thermometrics Surface Mount Devices. GE Sensing. Features
Features Tin plated terminations for soldering High sensitivity to changes in temperature Wide operating temperature range -58 F to 257 F (-50 C to 125 C) Rugged construction Available in other material
More information30 V to 60 V PTC Thermistors For Overload Protection
30 V to 60 V PTC Thermistors 238 66. 5.../PTCCL..H...BE FEATURES Wide range of trip and non-trip currents: From 94 ma up to 2 A for the trip current Small ratio between trip and non-trip currents (I t
More informationRF Transformer (Stabilized Matching Device) SMST18 series
1 Features RF Transformer Stabilized Matching Device is RF impedance matching component. You can adjust impedance matching easily between antenna and feeding point, when you use RF Transformer. RF Transformer
More informationReference Only. Marked three digits system.(ex. 270pF 271) 8 Lead Type
Spec No. JENF243F-0018K-01 P1/11 Disc-Type EMIFIL (A miniature three-terminal capacitor) DSS6N 1.Scope This reference specification applies to DSS6N series. 2.Part Numbering (Ex.) DS S 6 N B3 2A 271 Q93
More informationHigh Ohmic / High Voltage Metal Glaze Leaded Resistors
High Ohmic / High Voltage Metal Glaze Leaded Resistors A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper
More informationIt is composed of description, rated wattage, nominal resistance, tolerance and packaging Explanation of part numbers : E J B P
page 1/7 1. APPLICABLE SCOPE : 1.1 This specification is for use in METAL OXIDE FILM FIXED RESISTORS 1.2 Characteristics and Specifications are according to those of : MIL-STD-105 MIL-STD-202 2. TYPE JIS
More informationReference Only. Chip Ferrite Bead BLM31 SH1L Murata Standard Reference Specification [AEC-Q200]
P.1/9 Chip Ferrite Bead BLM31 SH1L Murata Standard Reference Specification [AEC-Q200] 1. Scope This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM31_SH Series based
More information4. Type & Dimensions No.JEMCP B (Unit:mm) MURATA PART NO. (1)-1 L a (1)-2 W b T e g d p 1 NFA31CC101S1E4D 3.2± ± ± min. 2 N
No.JEMCP0-010875B CHIP EMIFIL CHIP 3-TERMINAL CAPACITOR ARRAY TYPE FOR GENERAL NFA31CC Series Reference Sheet 1.Scope 2.Reference PART No. List 1 2 3 4 5 6 7 8 This product specification is applied to
More informationPosistor for over current protection PRG SERIES BC-E0273H PRG21BC***MM1RA SERIES
Posistor for over current protection PRG SERIES BC-E0273H PRG21BC***MM1RA SERIES 1.Part Numbering ex) PR G 21 BC 0R2 M M1 RA C Product ID Series Dimensions Temperature Resistance Resistance Individual
More informationFrelTec GmbH. Multi-Layer Power Inductor SMD
GmbH Mathildenstr. 10A 82319 Starnberg Germany SMD 4/15/2013 1/13 GmbH www.freltec.com SPECIFICATION Part Number 141 02 * 101 * M T04 * Type Size Value Toleranc e Packing 141 : SMD Multi-Layer Power Inductor
More information2.4 GHz ISM Band Working Frequency
MULTILAYER CERAMIC ANTENNA RFANT Series RoHS Compliance 2.4 GHz ISM Band Working Frequency P/N: RFANT3216120A1T Series *Contents in this sheet are subject to change without prior notice. Page 1 of 9 ASC_RFANT3216120A1T_V04
More informationLighthouse LEDs. Technical Data Sheet. Customer Approval. Product Name High Bright Blue LED. Part Number. Customer. Customer PN. Version.
Technical Data Sheet Product Name 3528 High Bright Blue LED Part Number A-1210UBC Customer Customer PN Version Date Customer Approval Instituted By Checked By: Approved By 1. Features: Package ( L/W/H
More informationReference Only. This reference specification applies to Chip Ferrite Bead Array BLA31 Series used for electronic machinery. (8)Numbers of Circuit
Spec. No. JENF243A 0008N-01 P 1 / 9 1. Scope Chip Ferrite Bead Array BLA31SN4 Reference Specification This reference specification applies to Chip Ferrite Bead Array BLA31 Series used for electronic machinery.
More informationApplications R41 3 I M1 M
R41, Class Y2, 300 VAC, 110 C (Automotive Grade) Overview The R41 is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements
More informationMetal (Oxide) Film Resistors
Metal (Oxide) ilm Resistors Metal (Oxide) ilm Resistors Type: ERG(X)S (Small size) (.5,, 2, 3, 5 ) ERG(X) (nti-heat conducting for C) (, 2, 3, 5 ) n eatures l Value Correspondence resistance value range
More informationMULTILAYER CERAMIC ANTENNA
RFANT Series RoHS Compliance MULTILAYER CERAMIC ANTENNA 2.4 GHz ISM Band Working Frequency P/N: RFANT5220110A1T *Contents in this sheet are subject to change without prior notice. Page 1 of 9 ASC_RFANT5220110A1T_V02
More informationBROADBAND RFCMF 1220(0508) Series RoHS Compliance MULTILAYER COMMON MODE FILTER. For USB 2.0 / IEEE 1394 Application
BROADBAND RFCMF 1220(0508) Series RoHS Compliance MULTILAYER COMMON MODE FILTER Halogens Free Product For USB 2.0 / IEEE 1394 Application P/N: RFCMF1220100M4T *Contents in this sheet are subject to change
More informationHottech Thick Film Chip Resistors
1. PART NUMBER e.g.: RI0603L1003FT RI 0603 L 1003 F T Code: Thick Film Chip Resistor Size: 0201 0402 0603 Resistance Value: Three digits (E-24): the first 2 digits are significant and the Tolerance: B=±0.1%
More informationChip tantalum capacitors (Bottom surface electrode type : Large capacitance) Anode mark (Unit : mm) Dimensions L 1.6 ± 0.1 W ± 0.
Chip tantalum capacitors (Bottom surface electrode type : Large capacitance) TC Series Case Features 1) Bottom electrode configuration results in significantly greater compactness. 2) Filet formation enables
More informationSpec. No. JENF243H-0006H-01 P 1/ 7
Spec. No. JENF243H-0006H-01 P 1/ 7 1. Scope 2. Rating Block Type EMIFIL BNX005-01 Reference Specification This reference specification applies to Block Type EMIFIL. 2.1 Customer Part Number 2.2 Murata
More informationReference Only. Spec No. JELF243B-9102E-01 P.1 / 9
Spec No. JELF243B-9102E-01 P.1 / 9 CHIP COIL (CHIP INDUCTORS) LQG18HH 00D SPECIFICATION Murata Standard Reference Specification [AEC-Q200] 1. Scope This reference specification applies to LQG18HH_00 series
More informationP/N: RFECA A1T. Halogens Free Product. 2.4 GHz ISM Band Working Frequency. RFECA Series RoHS Compliance CERAMIC ANTENNA.
RFECA Series RoHS Compliance CERAMIC ANTENNA Halogens Free Product 2.4 GHz ISM Band Working Frequency P/N: RFECA32166A1T *Contents in this sheet are subject to change without prior notice. Page 1 of 9
More informationGeneral Purpose Metallized Polyester Film Capacitors R82 Series, Radial, 5 mm Lead Spacing, VDC (Automotive Grade) Applications
General Purpose Metallized Polyester Film Capacitors R82 Series, Radial, 5 mm Lead Spacing, 50 400 VDC (Automotive Grade) Overview The R82 Series is constructed of metallized polyester film (wound or stacked
More informationNo.JEMCP B a)equivalent Circuit 5.Rated value MURATA PART NO. NFM2CC0UH3D NFM2CC02RH3D (3) Nominal Capacitance Capacitance Tolerance
No.JEMCP0-00863B CHIP EMIFIL CHIP 3-TERMINAL CAPACITOR FOR GENERAL NFM2CC Series Reference Sheet.Scope 2.Reference PART No. List 2 3 4 5 6 7 8 3.MURATA Part NO. System (Ex.) This product specification
More informationReference Only. Spec. No. JENF243E-0003Q-01 P 1 / 8. Chip EMIFIL LC Combined Type for Large Current NFE61PT 1H9 Reference Specification
Spec. No. JENF243E-0003Q-01 P 1 / 8 Chip EMIFIL LC Combined Type for Large Current NFE61PT 1H9 Reference Specification 1. Scope This reference specification applies to Chip EMIFIL LC Combined Type for
More informationReference Only. Spec No. JELF243A-9134D-01 P1/8
Spec No. JELF243A-9134D-01 P1/8 CHIP COIL(CHIP INDUCTORS)LQH2MPZ GRL SPECIFICATION Murata Standard Reference Specification AEC-Q200 1. Scope This reference specification applies to LQH2MPZ_GR Series, Chip
More informationReference Only. 1. Scope This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW5AT_SQ Series.
Spec No. JEFL243C 0017H-01 P 1/10 Wire Wound Chip Common Mode Choke Coil DLW5ATN SQ2 Reference Specification 1. Scope This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW5AT_SQ
More informationElectrical Specifications. Maximum Overload Current (A) Maximum Rating Current (A)
Features: High power metal alloy current sense resistor High temperature performance up to 225 C; for operation up to 275ºC, contact factory Excellent frequency response Low thermal EMF (
More informationReference Only. Spec.No.JENF243A-0034J-01 P1/8
Spec.No.JENF243A-0034J-01 P1/8 Chip Ferrite Bead BLM03H N1 Reference Specification 1.Scope This reference specification applies to Chip Ferrite Bead BLM03H N Series. 2.Part Numbering (ex.) BL M 03 HG 601
More information5.Rated value MURATA PART NO. NFM31HK103R1H3L (3) Nominal Capacitance Capacitance Tolerance (5) Rated Voltage pf ±20 % DC 50 V Rated C
No.JEMCP0-013583A CHIP EMIFIL CHIP 3-TERMINAL CAPACITOR FOR VERY LARGE CURRENT FOR AUTOMOTIVE NFM31HK Series Reference Sheet 1.Scope 2.Reference PART No. List 1 2 3 4 5 3.MURATA Part NO. System (Ex.) This
More informationApplications R49 A N B1 M
R49, Class X1, 330 VAC, 110 C Overview The R49 is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V 0. Applications
More informationApplications R46 K I P0 M
Overview The R46 Series is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V 0. Applications For worldwide
More informationNARROW PITCH (0.4mm) CONNECTORS P4S SERIES
FOR BOARD-TO-BOARD AND BOARD-TO-FPC CONNECTION AXT3, 4 NARROW PITCH (0.4mm) CONNECTORS P4S SERIES NEW 2. Strong resistance to adverse environments! Utilizes construction for high contact reliability. 1)
More informationFRSM Series (Z1 Foil Technology)
(Z1 Foil Technology) UltraHigh-PrecisionFRSMWrap-AroundChipResistors,Z1FoilTechnologyConfiguration Resistors, Z1 Foil Technology Configuration with TCR of ±0.05 ppm/ C and Improved Load-Life Stability
More informationReference Only. This reference specification applies to Wire Wound Chip Common Mode Choke Coil.
Spec. No. JEFL243C-0025G-01 P 1/10 Wire Wound Chip Common Mode Choke Coil DLW5BTM TQ2 Reference Specification 1. Scope This reference specification applies to Wire Wound Chip Common Mode Choke Coil. 2.
More informationPSE Technology Corporation
PSE Technology Corporation SPECIFICATION FOR APPROVAL CUSTOMER NOMINAL FREQUENCY PRODUCT TYPE SPEC. NO. ( P/N ) CUSTOMER P/N ISSUE DATE VERSION 32.768 KHz TYPE G9 SMD CRYSTAL G93270002 0 Oct.31,2013 C
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
Power Resistor for Mounting onto a Heatsink Thick Film Technology DESIGN SUPPORT TOOLS click logo to get started FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series
More informationProduct Specification
Product Name : AEM Part Number : Customer : Customer Revision: 2 Date: 2011-09-08 AEM Components (Suzhou) Co., Ltd 458 Shenhu Road, Suzhou Industrial Park Jiangsu, P.R China, 215122 TEL: 86-512-6258-0028
More informationImpedance ( ) (at 100MHz,Under Standard Testing Condition) Typical 5~ ~ ±25%
Reference Spec.No.JENF243A-0018AJ-01 P1/11 Chip Ferrite Bead BLM15 SN1 REFERENCE SPECIFICATION 1.Scope This reference specification applies to Chip Ferrite Bead BLM15_SN series. 2.ing (ex.) BL M 15 AG
More informationPSE Technology Corporation
PSE Technology Corporation SPECIFICATION FOR APPROVAL CUSTOMER NOMINAL FREQUENCY PRODUCT TYPE SPEC. NO. ( P/N ) CUSTOMER P/N ISSUE DATE VERSION 32.768 KHz TYPE G9 SMD CRYSTAL G93270004 0 Oct.25,2013 B
More informationAVX High Power Resistive Products
AVX High Power Resistive Products www.avx.com Version 15.1 Table of Contents ATTENUATORS....................................................... 2-3 Leaded Chip Attenuators...........................................
More informationMulti-Layer Ferrite Inductors
Multi-Layer Ferrite Inductors ORDERING CODE IF 1608 R56 J T S 8 PRODUCT CODE IF : Multilayer Ferrite Inductor (Lead Free) DIMENSION (L X W) Code Dimension EIA 1005 1.0 x 0.50 mm 0402 1608 1.6 x 0.80 mm
More information5W White SPHWHTA3N500
Product Family Data Sheet Rev. 00 2016.11.01 111 High Power LED Ceramic Series 5W White SPHWHTA3N500 Features & Benefits Package : Silicone covered ceramic substrate Dimension : 3.5 mm x 3.5 mm Technology
More informationReference Only. Reference Spec.No.JENF243A-9103H-01 P1/8. Chip Ferrite Bead BLM15 SH1D Reference Specification [AEC-Q200]
Reference Spec.No.JENF243A-9103H-01 P1/8 Chip Ferrite Bead BLM15 SH1D Reference Specification [AEC-Q200] 1.Scope This reference specification applies to Chip Ferrite Bead BLM15_SH series for Automotive
More informationP/N: RGCMF H4T. RGCMF Series 1210(0504)- RoHS Compliance MULTILAYER CERAMIC COMMON MODE FILTER. Halogens Free Product.
RGCMF Series 1210(0504)- RoHS Compliance MULTILAYER CERAMIC COMMON MODE FILTER Halogens Free Product P/N: RGCMF1210121H4T *Contents in this sheet are subject to change without prior notice. Page 1 of 7
More informationInductors. 1 Rev
Inductors Content Multi-Layer Power Inductors (IP Series)... 2 Ordering Code... 2 Standard External Dimensions... 3 Multi-Layer Ferrite Inductor for General Use (F Type)... 4 Multi-Layer Power Inductor
More informationPSE Technology Corporation
PSE Technology Corporation SPECIFICATION FOR APPROVAL CUSTOMER NOMINAL FREQUENCY PRODUCT TYPE SPEC. NO. ( P/N ) CUSTOMER P/N ISSUE DATE VERSION 32.768 KHz TYPE G8 SMD CRYSTAL 0 Jun.16,2016 A APPROVED PREPARED
More informationPrecision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
More informationWLFM2520 Multi-Layer Power Inductors
WLFM2520 Multi-Layer Power Inductors *Contents in this sheet are subject to change without prior notice. Page 1 of 9 ASC_WLFM2520 Series_V1.0 Dec. 2014 Features 1. General purpose chip ferrite power inductor
More informationTel: (01793) Fax: (01793) A Selection Guide to SMD Trimmer Potentiometers. Size. Features. Element. Adjust. Product. Cermet.
Meggitt Citec SMD Trimmers Selection Guide A Selection Guide to SMD Trimmer Potentiometers Size Element Adjust Features Product 2mm Cermet Top Auto Adjust Head 3121 Top Semi-Sealed 3203 3mm Cermet Top
More informationWirewound Resistors, Industrial Power, Aluminum Housed, Chassis Mount
Wirewound Resistors, Industrial Power, Aluminum Housed, hassis Mount DESIGN SUPPORT TOOLS Models click logo to get started FEATURES Molded construction for total environmental protection omplete welded
More informationSMD PTC - Nickel Thin Film Linear Thermistors
SMD PTC - Nickel Thin Film Linear Thermistors Notes (1) Contact if closer TCR lot tolerance is desired. (2) Other R 25 -values and tolerances are available upon request. (3) Rated continuous working voltage
More informationSP3S-AQ2-01 AIR QUALITY SENSOR S March, 2004
SP3S-AQ2-01 SPECIFICATIONS MODEL: TYPE: SPECIFICATION No. DATE OF ISSUE SPECIFICATIONS FOR: SP3S-AQ2-01 AIR QUALITY SENSOR S-0403-03 18 March, 2004 Dimensions 0.7 Status Name Date Original Junko Yanagitani
More informationWirewound Resistors, Industrial Power, Aluminum Housed, Chassis Mount
Wirewound Resistors, Industrial Power, FEATURES Molded construction for total environmental protection omplete welded construction Meets applicable requirements of MIL-PRF-18546 Available in non-inductive
More informationTO-2013BC-MYE. Surface Mount Device LED. Features. Dimensions MOLDING BODY(LENS) 0.40 PCB 0.40 CATHODE MARK SOLDERING TERMINAL
TO-2013BC-MYE Surface Mount Device LED Part Number Material Chip Source Color Lens Color TO-2013BC-MYE AlGaInP Yellow Water clear Features IC compatible Compatible with automatic placement equipment Compatible
More informationan ISO9001 company TECHNICAL INFORMATION FOR TGS2600 Technical Information for Air Quality Control Sensors
Technical Information for Air Quality Control Sensors an ISO900 company The Figaro 2600 series is a new type thick film metal oxide semiconductor, screen printed gas sensor which offers miniaturization
More informationRF Transformer (Stabilized Matching Device) SMST21NMHB series
1 Features RF Transormer Stabilized Matching Device is RF impedance matching components. You can adjust impedance matching easily between antenna and eeding point, when you use RF Transormer. RF Transormer
More informationMultilayer NTC Thermistors
Multilayer NTC Thermistors Series: ERTJ Handling Precautions Safety Precautions Multilayer NTC Thermistors (hereafter referred to as Thermistors ) should be used for general purpose applications found
More information10 Manor Parkway, Suite C Salem, New Hampshire
Micro-Precision Technologies (MPT) is an independent manufacturer of hybrid integrated circuits, multichip modules, and high-precision thick film substrates for the military, medical, avionics, optoelectronics,
More informationReference Only. Chip Ferrite Bead BLM18 H1D Murata Standard Reference Specification [AEC-Q200]
Chip Ferrite Bead BLM18 H1D Murata Standard Reference Specification [AEC-Q200] P.1/10 1.Scope This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM18_ H Series based
More information