Filtration for Oil and Gas

Transcription

1

2 Filtration for Oil and Gas Treated Gas Outlet Amine Cooler Re-Generator Acid Gas Amine Pump Charcoal Filter Contactor Lean Amine Fine Filter Cartridges Lean Amine Pre-Filter Cartridges Reflux Accumulator Sour Gas Inlet Flash Gas Rich Amine to Exchanger Rich Amine to Filter Re-Generator Reboiler Flash Tank Rich Amine Filter Cartridge Amine Booster Pump Filtration applications in amine treatment process Stripper Gas Skimmer Stripper Reboiler Absorber Surge Tank Gas Glycol Heat Exchanger Glycol Heat Exchanger Coalescer Cartridges Condensate Glycol Filter Cartridge Glycol Filter Cartridge Wet Gas Inlet Drain Dry Gas Outlet Filtration applications in gas dehydration process

3 Filtration Applications for Oil and Gas Amine Sweetening Contaminants in the re-circulating amine cause foaming, fouling and plugging of contactor trays, resulting in amine carry-over, reduced throughput, increased amine make-up, higher differential pressure and reduced adsorptive capacity. Moreover, there are losses due to higher energy consumption and poor heat transfer in the heat exchangers. Contaminants include iron oxides, iron sulfides and other particulate matter. Sedifilt Filters for amine sweetening give excellent results in terms of amine clarity that becomes transparent visually with excellent removal of total suspended solid impurities Glycol Dehydration Sedifilt Filters at the absorber gas inlet will eliminate solids and prevent foaming, and will protect the recirculating glycol stream resulting in better efficiency of the dehydration process. Filtration removes scale, corrosion and dust particulates to keep the recirculating glycol clean and clear. Produced Water (well water injection and disposal water filtration) Solid contaminants such as iron oxides, iron sulfides, and asphaltines (tar-like particulate) can cause reduced porosity of the injection well, resulting in premature plugging or other damage to equipment. Filtration of produced water maintains the porosity and injectivity of the well formation, reducing the risk of expensive workovers. Coalescer The innovative design of Sedifilt Coalescer cartridges dramatically reduces the cost of filtration with enhanced performance. The high-bulk, stable, three-dimensional random structure comprising multi-lobal filaments results in direct interception and coalescence of dispersed liquid phase. Applications include removal of aerosols and condensates from natural gas streams, also removing particulate contaminants down to 0.6 microns. Gas Distribution Systems (condensate removal) Sedifilt Coalescer cartridge is ideal for condensate removal and oil adsorption in both liquid/liquid and liquid/gas applications. Lube Oil Filtration of lubricating oils before final packing ensures consistent clarity and removes any solid residues. Sedifilt polyester media filter cartridges with galvanized steel core provide superior contaminant retention for lube oil filtration. Process Water It is important to filter process water to remove silt, sand and other suspended solid contaminants and other impurities from process water for reliable and efficient performance of softeners, deionizers and heat exchangers. Sedifilt extractable-free media cartridges produce excellent silt density index (SDI) results for membrane pre-filtration on RO systems, reducing membrane fouling and cleaning costs, and increased membrane performance and life. Filtration for Oil and Gas

4 Superior Filtration Technology Sedifilt Filters for Oil and Gas applications have proven exceptional performance. A wide chemical compatibility and customization possibilities result in improved economics tailored to the individual application. Sedifilt Filters improve process efficiency and also provide process protection by removing suspended solids such as dirt, iron particulates and deformable gel type contaminants. Sedifilt Oil and Gas Filters are available for particulate filtration and coalescing. True graded density structure of Sedifilt cartridges ensure higher dirt holding capacity, longer service life, and fewer change outs. Features 100% polypropylene inert material, excellent micro-organism resistance. No chemicals to leach-out with new melt spinning and yarn forming process. No media migration because the yarn consists of continuous filaments. True graded density new winding technology gives denser winding in inner layers and coarser winding in outer layers. High dirt holding capacity and longer life as particles are trapped throughout the entire cross section of the filter. Better performance multi-lobal cross section filaments with random 3- dimensional media structure captures more particles compared to conventional filters. High bulk media having improved void to solid ratio gives higher flow rates with low pressure drop. High structural stability, i.e., no shifting of media, excellent knife-edge sealing. Structural firmness results in greater resistance to particle unloading and hence more consistent performance. Incinerates to trace ash with no hazardous volatiles for environmentally friendly disposal. Illustration: Sedifilt graded density structure Chemical Compatibility Sedifilt filters for oil and gas applications meet chemical compatibility requirements for most processes. Please consult our chemical resistance guide for chemical compatibility information on our filter media and core material. Sedifilt Media Sedifilt media has high bulk, stable, three-dimensional random structure comprising continuous filaments. Filtration for Oil and Gas The multi-lobal cross section of individual filaments has more microvoids giving higher dirt holding capacity and lower resistance to flow.

5 Filter Cartridge Coalescer Cartridge Pure polypropylene Sedifilt filter cartridges are free from any extractables and contain no lubricants, wetting agents, emulsifiers, ant-oxidants or anti-static agents, etc. The standard pure polypropylene cartridge is engineered for superior filtration performance. Available in up to 72 inch (1829 mm) length and up to 6 inch (152 mm) diameter. Innovative Sedifilt Coalescer cartridges are available in standard lengths of 24 and 36 inches to fit into standard coalescer housings (from most manufacturers). Coalescer cartridges with galvanized steel core, metal end caps with neoprene gaskets and cotton covering are also available in customized lengths up to 72 inch and diameters up to 6 inch (152 mm). Pure polypropylene molded adapter with 222 O-rings Reusable knife-edge seal end cap with stainless steel spring Thermally welded pure polypropylene closed end cap Pure polypropylene molded spring Stepped end configurations available in all media Pure polypropylene molded fin end cap End Adapters Polypropylene end adapters are thermally-welded to the pure polypropylene Sedifilt filter. The positive weld assures bypass-proof performance and structural integrity without adhesives or additives, maintaining cartridge purity. All adapters are molded of the same polypropylene as the cartridge for chemical compatibility and ease of disposal. Pure polypropylene extended core Pure polypropylene tapered extended core Stainless Steel 316L tapered extended core Filter Cores Filter cores are available in polypropylene, stainless steel (304/316L) and galvanized carbon steel, in regular, extended and tapered configurations. Polypropylene core is the economical choice for most applications Stainless Steel core extends chemical, temperature, and differential pressure limits of cartridge. Galvanized Carbon Steel core Filtration for Oil and Gas

6 Filter Cartridge Test Results Ratings are based on laboratory tests for 10 inch cartridges as per ASTM F795 standard at ambient temperature and 3 gpm (US) water flow rate. Flow rate vs. pressure drop data is based on clean water at an ambient temperature of 25 C. Results in actual use will be influenced by the type of fluid and contaminant as well as flow rate and temperature. Coalescer Cartridge Test Results Filtration for Oil and Gas

7 Ordering Information Sedifilt cartridges can also be made to order in customized sizes (I.D, O.D, and lengths) in various filter media and core material, and tailored density gradings. Aqua Clear Filter Cartridge Outer Diameter Number per box (standard packing) Gross weight per box (kg) Quantity per 20 ft. Container Load (non-palletized) Quantity per 20 ft. Container Load (on pallets) When ordering for the first time, please specify all details in writing. Media, actual length, micron rating, outer and inner diameters, and core material are required. End adapters are optional. Contact us for further information. S L 40 A 5 A E222/C - G 35 Media Nominal Actual Variation in Micron Rating Outer Diameter (mm) End Adapters Core Material None = Extractables Free Polypropylene L = Low Extractables Polypropylene P = Polyester B = Bleached Cotton C = Natural Cotton D = Strainer Cartridge E = Coalescer Cartridge (inch) (inch) 9 7/8 19 3/4 29 5/8 39 1/2 49 1/4 72 (mm) Custom lengths are available up to full 50 inches. does not include end adapter length, if any. None = Nominal A = Specified Actual length of standard nominal lengths is specified on the left. For custom lengths, specify length in inches followed by an A for variation in length from standard A = 63.5 E = 60 D = 100 J = Custom outer diameters are available up to 152 mm. E222/C = Two end caps, one with double 222 O- rings (E222), other end flat closed (EC) E222 = Double 222 O- rings end cap EC = Closed end cap ES = Stepped end ER = Reusable stainless steel spring EA = Polypropylene molded spring EF = Polypropylene molded fin end cap EM = Metal end cap with gasket X = Extended Core XT = Tapered Extended Core (all core media) None = No end adapters (double open end - DOE) None = 100% Polypropylene S = Stainless Steel 304/316L G = Galvanized Carbon Steel Inner Diameter 27 mm 35 mm Polypropylene cores are available in 27 and 35 mm inner diameter. Custom inner diameters are available in metal cores. For a standard Sedifilt 5 micron 40 inch long (nominal) filter cartridge the product code will be S40-5A. An example of a cartridge with all options specified is SL40A-5AE222/C-G35.

8 Visit us on the Web at Sector 15, Korangi Industrial Area, Karachi 74900, Pakistan Phone: Fax: Sedifilt Superior filtration technology The information given in this publication is based on the present state of our knowledge. Any conclusions and recommendations are made without liability on our part. Buyers and users should make their own assessment of our products under their own conditions and for their own requirements. Syntech Fibres (Pvt) Ltd. Sedifilt and the logo Sedifilt are registered trademarks of Syntech Fibres (Pvt) Ltd. Certified by NSF International to NSF/ANSI Standard 61 2/2008 SM/01/014 Revision 0