NZQA Expiring unit standard 2117 version 5 Page 1 of 5. Install, test, and maintain water supply backflow prevention devices
|
|
- Cleopatra Berry
- 6 years ago
- Views:
Transcription
1 Page 1 of 5 Title Install, test, and maintain water supply backflow prevention devices Level 4 Credits 11 Purpose This unit standard is for people who work in the plumbing industry. People credited with this unit standard are able to: determine requirements for, determine the position of, and install, test, and maintain water supply backflow prevention devices; work safely and with care; and demonstrate knowledge of regulatory requirements, selection of methods and materials, and underpinning concepts and principles, as applied to the installation, testing, and maintenance of water supply backflow prevention devices. Classification Plumbing, Gasfitting and Drainlaying > Plumbing Available grade Achieved Prerequisites Current plumbing certificate or licence as issued under the Plumbers, Gasfitters, and Drainlayers Act Guidance Information 1 Legislation, standards, and codes applicable to this unit standard include but are not limited to: Plumbers, Gasfitters, and Drainlayers Act 2006; Health and Safety in Employment Act 1992; Building Act 2004; Local Government Act 2002; Plumbers, Gasfitters, and Drainlayers Regulations 1977; Water Supplies Protection Regulations 1961; AS/NZS :1998 Water Supply Backflow prevention devices Materials, design and performance requirements; AS/NZS :2003, Plumbing and Drainage Water services, Section 5.2; and NZS 3604:1999 Timber Framed Buildings; NZS 5807:1980 Code of practice for industrial identification by colour, wording or other coding; available at New Zealand Building Code, Clause G10 Piped Services, Clause G12 Water Supplies, current versions and any related compliance documents, available at Backflow Prevention for Drinking Water Suppliers Code of Practice, 2006, available from the New Zealand Water and Wastes Association, water@nzwwa.org.nz.
2 Page 2 of 5 Any legislation, standard, or code superseding any of the above will apply, pending review of this unit standard. 2 Reference United States Environmental Protection Agency (EPA), Cross-Connection Control Manual, February 2003, Chapter 5. EPA 816-R , available at 3 backflow prevention devices for atmospheric vacuum break (AVB), pressure vacuum breaker (PVB), spill proof vacuum breaker (SPVB), wafer check, registered air gap, double detector check, double check valve, hose connection vacuum breaker, reduced pressure zone device, single detector check valve, vacuum break. For performance criterion 3.5 only the following from the range above are able to be tested pressure vacuum breaker (PVB), spill proof vacuum breaker (SPVB), double check valve, reduced pressure zone device. 4 Credit for this unit standard does not entitle the candidate to legally perform: the testing of backflow prevention devices in the capacity of an Independent Qualified Person (IQP), or Accredited Backflow Prevention Tester (ABT). 5 This unit standard requires the application of theory as included in the Plumbers, Gasfitters, and Drainlayers Regulations These Regulations are currently under review to align them with the newer Plumbers, Gasfitters, and Drainlayers Act Definitions Job requirements refers to specific requirements of the job at hand not covered by job specifications. Job specifications, for the purpose of this unit standard, refers to instructions (oral, written, graphic) and may include any of the following: manufacturers instructions; design drawing detail specifications; specifications from a specialist source such as an architect, designer, engineer, or a supervisor; and site or work specific requirements. Where job specifications are in conflict with applicable legislation, standards, and/or codes, such legislation, standards, and/or codes shall take precedence for the purpose of assessment. Maintain may refer to all or any of repair, upgrade, alter, remove. Other services refers to any existing installed services. Regulatory requirements, for the purpose of this unit standard, refers to applicable legislation, standards, and codes. Outcomes and performance criteria Outcome 1 Determine requirements for water supply backflow prevention devices. 1.1 Backflow prevention devices are described in terms of their operation. 1.2 Requirements for backflow prevention devices are identified in accordance with water supply features.
3 Page 3 of 5 pressure (negative, positive), flow, associated drains. 1.3 Backflow prevention devices are selected which are suitable for the risk. risk high, medium, low. Outcome 2 Determine the position of water supply backflow prevention devices. 2.1 Water supply backflow prevention devices and associated drains, if required, are positioned in accordance with manufacturers instructions. Outcome 3 Install and test water supply backflow prevention devices. 3.1 Water supply backflow prevention devices are installed in accordance with manufacturers instructions and relevant standards and codes. 3.2 Water supply backflow prevention devices are connected to connections and termination points in accordance with manufacturers instructions and relevant standards and codes. 3.3 Water supply backflow prevention devices are protected in accordance with manufacturers instructions and relevant standards and codes. 3.4 Water supply pipelines are identified by label and colour in accordance with relevant standards and codes. 3.5 Water supply backflow prevention devices are commissioned and tested in accordance with manufacturers instructions, EPA 816-R , and relevant standards and codes. 3.6 The installation meets job specifications. Outcome 4 Maintain water supply backflow prevention devices. 4.1 Installed water supply backflow prevention devices are assessed in accordance with maintenance requirements and relevant standards and codes. 4.2 Faults are identified in terms of causes and means of rectification.
4 Page 4 of Faults are rectified in accordance with maintenance requirements and job specifications. Outcome 5 Work safely and with care. 5.1 Practical activities are carried out avoiding harm to people and damage to property, other services, materials, tools, and equipment. Outcome 6 Demonstrate knowledge of regulatory requirements, selection of methods and materials, and underpinning concepts and principles, as applied to the installation, testing, and maintenance of water supply backflow prevention devices. 6.1 Applicable sections of legislation, standards, and codes are described in terms of their application to the installation, testing, and maintenance of water supply backflow prevention devices. 6.2 Selection of methods and materials is justified. job specifications, operation of the installed devices; may include job requirements. 6.3 Underpinning concepts and principles are explained in terms of their application to the installation, testing, and maintenance of water supply backflow prevention devices. back pressure, differential pressure, siphon. Replacement information This unit standard was replaced by unit standard and unit standard This unit standard is expiring. Assessment against the standard must take place by the last date for assessment set out below.
5 Page 5 of 5 Status information and last date for assessment for superseded versions Process Version Date Last Date for Assessment Registration 1 22 July December 2022 Revision 2 19 June December 2022 Revision 3 1 April December 2022 Review 4 25 October December 2022 Review 5 26 October December 2022 Consent and Moderation Requirements (CMR) reference 0003 This CMR can be accessed at Please note Providers must be granted consent to assess against standards (accredited) by NZQA, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment. Industry Training Organisations must be granted consent to assess against standards by NZQA before they can register credits from assessment against unit standards. Providers and Industry Training Organisations, which have been granted consent and which are assessing against unit standards must engage with the moderation system that applies to those standards. Requirements for consent to assess and an outline of the moderation system that applies to this standard are outlined in the Consent and Moderation Requirements (CMR). The CMR also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.
NZQA Expiring unit standard version 2 Page 1 of 5. Install and maintain roofing, rainwater handling, and cladding systems, and flashings
Page 1 of 5 Title Install and maintain roofing, rainwater handling, and cladding systems, and flashings Level 4 Credits 25 Purpose This unit standard is for people who work in the plumbing industry. People
More informationNZQA registered unit standard version 1 Page 1 of 5. Develop, implement and review a HACCP application for a food processing operation
Page 1 of 5 Title Develop, implement and review a HACCP application for a food processing operation Level 5 Credits 20 Purpose This unit standard is for experienced people required to have in-depth knowledge
More informationNZQA registered unit standard 9537 version 5 Page 1 of 6. This unit standard applies to operational activities carried out on producing wellheads.
Page 1 of 6 Title Replace faulty petrochemical wellhead equipment Level 4 Credits 8 Purpose This unit standard applies to operational activities carried out on producing wellheads. People credited with
More informationNZQA registered unit standard version 3 Page 1 of 5
Page 1 of 5 Title Apply occupational health and safety requirements in the road transport and logistics industry Level 5 Credits 8 Purpose This unit standard is designed for team leaders, despatchers,
More informationNZQA registered unit standard 9536 version 5 Page 1 of 6. Undertake petrochemical wellhead maintenance activities under supervision
Page 1 of 6 Title Undertake petrochemical wellhead maintenance activities under supervision Level 3 Credits 4 Purpose This unit standard applies to operational activities carried out on producing wellheads.
More informationNZQA registered unit standard 9506 version 5 Page 1 of 5. Conduct a sample analysis in a petrochemical laboratory
Page 1 of 5 Title Conduct a sample analysis in a petrochemical laboratory Level 4 Credits 6 Purpose This unit standard is for people employed in the petrochemical industry. People credited with this unit
More informationNZQA registered unit standard version 3 Page 1 of 5
Page 1 of 5 Title Operate the drill rig for horizontal directional drilling Level 3 Credits 15 Purpose People credited with this unit standard are able to: care for and maintain horizontal directional
More informationNZQA registered unit standard version 4 Page 1 of 5
Page 1 of 5 Title Describe drinking-water supply reticulation systems Level 5 Credits 8 Purpose People credited with this unit standard are able to describe: the reticulated services found on public and
More informationNational Certificate in Painting with optional strands in Wall Coverings, Spray Techniques, Specialised Coatings, and Industrial Coatings
NZQF NQ Ref 1071 Version 2 Page 1 of 9 National Certificate in Painting with optional strands in Wall Coverings, Spray Techniques, Specialised Coatings, and Industrial Coatings Level 3 Credits 116 This
More informationPUBLIC SECTOR SERVICE DELIVERY Establish client needs and gain agreement on requirements for public sector service delivery
1 of 5 level: 6 credit: 15 planned review date: February 2006 sub-field: purpose: entry information: accreditation option: moderation option: Public Sector Services People credited with this unit standard
More informationNZQA unit standard version 2 Page 1 of 5. Demonstrate understanding of a HACCP application in a food processing operation
Page 1 of 5 Title Demonstrate understanding of a HACCP application in a food processing operation Level 4 Credits 10 Purpose This unit standard is for experienced operators and others required to have
More informationNZQA registered unit standard version 4 Page 1 of 5
Page 1 of 5 Title Formulate event management strategies and coordinate event management services for a public relations event Level 6 Credits 10 Purpose This unit standard is for people who have, or seek
More informationNZQA registered unit standard version 6 Page 1 of 5
Page 1 of 5 Title Demonstrate knowledge of circuit protection Level 3 Credits 3 Purpose This unit standard is for electricians and related trades who need to understand and select devices for the protection
More informationELECTRICITY SUPPLY - POWER SYSTEM MAINTENANCE Carry out routine inspection and servicing on high voltage minimum oil circuit breakers
1 of 9 level: 4 credit: 6 planned review date: December 2006 sub-field: purpose: entry information: Electricity Supply People credited with this unit standard are able to: prepare for inspection, testing
More informationNZQA registered unit standard version 2 Page 1 of 5. Demonstrate knowledge of safety management systems for an aviation environment
Page 1 of 5 Title Demonstrate knowledge of safety management systems for an aviation environment Level 5 Credits 8 Purpose People credited with this unit standard are, for an aviation environment, able
More informationNZQA registered unit standard version 1 Page 1 of 5. Diagnose and repair faulty electronic equipment to component level
Page 1 of 5 Title Diagnose and repair faulty electronic equipment to component level Level 4 Credits 40 Purpose This unit standard is intended for electronics technicians who are responsible for the diagnosis
More informationNZQA registered unit standard version 2 Page 1 of 5. Describe the roles and functions of a CIMS Incident Management Team (IMT) at an incident
Page 1 of 5 Title Describe the roles and functions of a CIMS Incident Management Team (IMT) at an incident Level 4 Credits 4 Purpose People credited with this unit standard are able to describe: the interrelated
More informationDemonstrate knowledge of servicing automotive air conditioning systems
Demonstrate knowledge of servicing automotive air conditioning systems 24448 version 1 Page 1 of 5 Level 3 Credits 2 Purpose This theory-based unit standard is for people in the automotive repair industry.
More informationOperate a root crop harvester
Page 1 of 5 Operate a root crop harvester Level 4 Credits 20 Purpose People credited with this unit standard are able to: select and prepare root crop harvesting equipment and machinery; carry out field
More informationNZQA registered unit standard version 3 Page 1 of 5
Page 1 of 5 Title Demonstrate and apply knowledge of safe welding principles and quality assurance under supervision Level 2 Credits 4 Purpose This unit standard is for the training of mechanical engineering
More informationNZQA registered unit standard 738 version 5 Page 1 of 7
Page 1 of 7 Title Kiln dry timber Level 4 Credits 25 Purpose People credited with this unit standard are able to: demonstrate knowledge of kiln drying operations; demonstrate knowledge of dry and wet bulb
More informationTransport perishable products by road
Page 1 of 5 Transport perishable products by road Level 4 Credits 25 Purpose This unit standard is for those who drive, or intend to drive, road transport vehicles transporting perishable products. People
More informationROAD TRANSPORT OPERATIONS Manage the transport of overdimension and overweight loads by road
1 of 7 level: 5 credit: 10 planned review date: July 2009 sub-field: purpose: Commercial Road Transport This unit standard is intended for people who are involved with managing the despatch and/or supervision
More informationPUBLIC SECTOR SERVICE DELIVERY Develop public sector service delivery objectives, and implement systems to meet client needs
1 of 5 level: 7 credit: 20 planned review date: February 2006 sub-field: purpose: entry information: accreditation option: moderation option: Public Sector Services People credited with this unit standard
More informationCarry out routine inspection and servicing on high voltage bulk oil circuit breakers
Page 1 of 6 Carry out routine inspection and servicing on high voltage bulk oil circuit breakers Level 4 Credits 6 Purpose People credited with this unit standard are able to: prepare for inspection, testing
More informationNZQA registered unit standard version 2 Page 1 of 5. Generate chlorine dioxide for wood pulp bleaching
Page 1 of 5 Title Generate chlorine dioxide for wood pulp bleaching Level 5 Credits 15 Purpose People credited with this unit standard are able to: explain fundamentals of chlorine dioxide generation;
More informationNational Certificate in Energy and Chemical Plant (Boiler Operation) (Level 2)
NZQF NQ Ref 1342 Version 2 Page 1 of 5 National Certificate in Energy and Chemical Plant (Boiler Operation) (Level 2) Level 2 Credits 42 This qualification has been reviewed. The last date to meet the
More informationNZQA registered unit standard version 5 Page 1 of 6. Operate hydro-electric generating plant from enterprise control room
Page 1 of 6 Title Operate hydro-electric generating plant from enterprise control room Level 6 Credits 16 Purpose People credited with this unit standard are able to: demonstrate knowledge of the principles
More informationREGISTRATION EXAMINATION, NOVEMBER 2012 LICENSED DRAINLAYER QUESTION AND ANSWER BOOKLET. Time allowed THREE hours
Affix label with Candidate Code Number here. If no label, enter candidate Number if known No. 9197 REGISTRATION EXAMINATION, NOVEMBER 2012 LICENSED DRAINLAYER INSTRUCTIONS QUESTION AND ANSWER BOOKLET Time
More informationBackflow prevention. Information for plumbers
Backflow prevention Information for plumbers If there are contaminants in the water, backflow can cause serious or even fatal injuries to our customers and yours Backflow prevention containment protects
More informationNZQA registered unit standard version 1 Page 1 of 7
Page 1 of 7 Title Manage conflict situations in a security context Level 3 Credits 4 Purpose This unit standard covers the management of conflict situations by security personnel. People credited with
More informationQUALIFICATION DETAILS
QUALIFICATION DETAILS Qualification Title New Zealand Certificate in Frame and Truss Detailing (Level 4) Version 1 Qualification type Certificate Level 4 Credits 160 NZSCED 040399 Architecture and Building
More informationROCHESTER PUBLIC UTILITIES PUBLIC WATER SYSTEM CROSS-CONNECTION CONTROL AND BACKFLOW PREVENTION PROGRAM FOR ROCHESTER, MINNESOTA
ROCHESTER PUBLIC UTILITIES PUBLIC WATER SYSTEM CROSS-CONNECTION CONTROL AND BACKFLOW PREVENTION PROGRAM FOR ROCHESTER, MINNESOTA Rochester Public Utilities 4000 East River Road NE Rochester, Minnesota
More informationThis qualification is expiring. The last date to meet the requirements is 31 December 2010.
NQF Ref 0141 Version 5 Page 1 of 8 National Certificate in Energy and Chemical Plant (Process Operation) (Level 4) with optional strands in Refrigeration, Steam Generation, Ancillary Operations, Geothermal,
More informationEstablish quality requirements, manage, and monitor the installation of subdivision infrastructure
Page 1 of 5 Establish quality requirements, manage, and monitor the installation of subdivision infrastructure Level 6 Credits 18 Purpose This unit standard is for people who are working, or who intend
More informationDecember Illinois American Water Cross Connection Control Program
December 2007 Illinois American Water Cross Connection Control Program INDEX Page SECTION I PURPOSE..... 1 SECTION II DEFINITIONS..... 3 SECTION III BACKFLOW PROTECTION REQUIREMENTS.....6 SECTION IV BACKFLOW
More informationSECURITY STAFF SERVICES Demonstrate knowledge of and operate electronic equipment as a security officer
1 of 5 level: 3 credit: 5 planned review date: March 2007 sub-field: purpose: Security This unit standard covers the use of electronic equipment for security s. People credited with this unit standard
More informationCross Connection Plumbing. James Peterson Plumbing Program Phone: (651) E mail:
Cross Connection Plumbing James Peterson Plumbing Program Phone: (651) 284 5889 E mail: jim.peterson@state.mn.us History Romans were first to use lead pipe to distribute water and remove waste water from
More informationDemonstrate an advanced knowledge of railway signals
Page 1 of 5 Demonstrate an advanced knowledge of railway signals Level 4 Credits 15 Purpose People credited with this unit standard are able to: demonstrate an advanced knowledge of fixed railway signals,
More informationPOULTRY HATCHERY Process day-old poultry chicks
1 of 5 level: 3 credit: 10 planned review date: December 2008 sub-field: purpose: entry information: accreditation option: moderation option: Poultry Production People credited with this unit standard
More informationAssist press operator on a reel-fed printing press
Page 1 of 5 Assist press operator on a reel-fed printing press Level 2 Credits 12 Purpose People credited with this unit standard are able to: follow safety requirements for the press being used; check
More informationIRRIGATION Demonstrate knowledge of irrigation systems, components, and performance
1 of 5 level: 4 credit: 6 planned review date: August 2006 sub-field: purpose: entry information: accreditation option: moderation option: Water Industry People credited with this unit standard are able
More informationInformation for building owners & building practitioners: Building work that does not require a building consent. Council discretionary exemptions
Information for building owners & building practitioners: Building work that does not require a building consent The Building Act has allowed for some specified work to be carried out without requiring
More informationAS/NZS :2003. Plumbing and drainage AS/NZS :2003. Australian/New Zealand Standard. Part 3: Stormwater drainage
AS/NZS 3500.3:2003 Incorporating Amendment Nos 1, 2, and 3 Australian/New Zealand Standard Plumbing and drainage Part 3: Stormwater drainage AS/NZS 3500.3:2003 AS/NZS 3500.3:2003 This Joint Australian/New
More informationBackflow Prevention Assembly Tester Expected Range of Knowledge Approved by the Backflow Prevention Assembly Tester 10/11/05
Backflow Prevention Assembly Tester Expected Range of Knowledge Approved by the Backflow Prevention Assembly Tester 10/11/05 The Expected Range of Knowledge is a Foundation upon which the Tester will build
More informationThis qualification has been revised. The last date to meet the requirements is 31 December 2021.
NZQF NQ Ref 0951 Version 7 Page 1 of 9 National Certificate in Electrical Engineering (Advanced Trade) (Level 5) with strands in Electrotechnology Specialisation, Electrical Installation, and Industrial
More informationCarry out off-road motorcycle training
Page 1 of 5 Carry out off-road motorcycle training Level 5 Credits 10 Purpose People credited with this unit standard are able to: prepare for a training session in riding motorcycles off-road; conduct
More informationVEHICLE BODYWORK Detail and groom a vehicle
1 of 5 level: 2 credit: 4 planned review date: December 2009 sub-field: purpose: entry information: accreditation option: moderation option: Motor Industry People credited with this unit standard are able
More informationPlumbing. Intro to Plumbing. ANZRA Agreement. TRA Trade Recognition Australia. Benchmarking occupational competencies. Gap training.
Plumbing Intro to Plumbing ANZRA Agreement TRA Trade Recognition Australia Benchmarking occupational competencies. Gap training. NOLs National Occupational Licensing Plumbing It Collects, Transports &
More informationNZQA registered unit standard version 1 Page 1 of 7. Plan and fell trees using advanced techniques in a commercial forest harvesting operation
Page 1 of 7 Title Plan and fell trees using advanced techniques in a commercial forest harvesting operation Level 4 Credits 25 Purpose This unit standard is intended for professional tree fellers in a
More informationMake ready a sheet-fed offset printing press for spot colour work
Make ready a sheet-fed offset printing press for spot colour work 26318 version 1 Page 1 of 5 Level 3 Credits 30 Purpose People credited with this unit standard are able to: check job documentation and
More informationThis qualification has been reviewed. The last date to meet the requirements is 31 December 2018.
NZQF NQ Ref 1412 Version 4 Page 1 of 20 National Certificate in Forest Operations Advanced (Level 4) with strands in Establishment and Silvicultural Operations Management, Production Tree Felling, Hauler
More informationSHORT COURSES. Industry Training New Zealand
SHORT COURSES Industry Training New Zealand 2 CONTENTS About Tai Poutini Polytechnic About Training for Industry Short Courses Cranes Truck Mounted Crane Pendant Crane Lifting Loads Telehandler Scaffolding
More informationLevel 4. Credits Purpose
NZQF NQ Ref 0756 Version 3 Page 1 of 11 National Certificate in Flooring (Level 4) with strands in Carpet Installation, Fine Sand and Finishes, Flooring Planning and Design, Resilient Flooring Installation,
More informationCONSENT AND MODERATION REQUIREMENTS (CMR) for Building and Construction
CONSENT AND MODERATION REQUIREMENTS (CMR) for Building and Construction Contact (version 9) The National Moderator Building and Construction Industry Training Organisation (BCITO) PO Box 2615 Wellington
More informationLEATHER - BOTTOM STOCK, MAKING AND LASTING Clean, dress, and spray footwear in a shoe room
1 of 6 level: 3 credit: 18 planned review date: November 2005 sub-field: purpose: entry information: accreditation option: moderation option: special notes: Footwear and Leather Trades People credited
More informationNZQA registered unit standard version 1 Page 1 of 7. Fell trees in a commercial forest harvesting operation
Page 1 of 7 Title Fell trees in a commercial forest harvesting operation Level 3 Credits 10 Purpose This unit standard is designed for people who work as a tree feller on a day-to-day basis in a commercial
More informationThis qualification has been reviewed. The last date to meet the requirements is 31 December 2018.
NZQF NQ Ref 0880 Version 5 Page 1 of 7 National Certificate in Water Treatment (Level 4) Level 4 Credits 134 This qualification has been reviewed. The last date to meet the requirements is 31 December
More informationCONSENT AND MODERATION REQUIREMENTS (CMR) for Plastics Processing Technology
CONSENT AND MODERATION REQUIREMENTS (CMR) for Plastics Processing Technology Contact (version 5) Quality Assurance Manager Competenz PO Box 9005 Newmarket Auckland 1149 Telephone 0800 526 1800 Fax 09 539
More informationMemorandum from licensed building practitioner: Record of building work Section 88, Building Act 2004
binding margin Memorandum from licensed building practitioner: Record of building work Section 88, Building Act 2004 Please fill in the form as fully and correctly as possible. If there is insufficient
More informationNational Certificate in Forestry (Generic Skills - Workplace Safety and Operations) (Level 2) Level 2
NZQF NQ Ref 1409 Version 4 Page 1 of 10 National Certificate in Forestry (Generic Skills - Workplace Safety and Operations) (Level 2) Level 2 Credits 44 This qualification has been reviewed. The last date
More informationBackflow Preventer Tester Plumbing License Code Path
Backflow Preventer Tester Plumbing License Code Path P.A. 733 State Plumbing Act P.A. 230 State Construction Code Act P.A. 399, Part 14 Cross Connection Control Rules Michigan Plumbing Code International
More informationBackflow Prevention Program Revised:
Backflow Prevention Program Revised: Approved by Director OBJECTIVE: The purpose of this policy is to define the minimum requirements for all connections to the University potable water system. Compliance
More informationMilk Pre-Cooler Plumbing Considerations. ATCP 65, Wisconsin Administrative Code and the 2015 PMO
Milk Pre-Cooler Plumbing Considerations ATCP 65, Wisconsin Administrative Code and the 2015 PMO Protection of Potable Water Supply Protecting potable water supply (well) Raw milk and chemical cleaning
More informationThis qualification has been reviewed. The last date to meet the requirements is 31 December 2018.
NZQF NQ Ref 1344 Version 2 Page 1 of 20 National Certificate in Energy and Chemical Plant (Process Operation) with optional strands in Steam Generation; Turbine Operations; Waste Treatment; Refrigeration;
More informationSkills CFA Assessment Strategy Competence units (S/NVQ)
Skills CFA Assessment Strategy Competence units (S/NVQ) Business Administration Customer Service Management and Leadership 2014 Skills CFA BA, CS, M&L Assessment Strategy: August 2014 (version 5.0) Page
More informationSTANDARDS FOR BACKFLOW PREVENTION ASSEMBLIES
STANDARDS FOR BACKFLOW PREVENTION ASSEMBLIES October 2009 200 South Ivy Street - Room 177 Medford, Oregon 97501 Phone: (541) 774-2430 Fax: (541) 774-2555 Standards For Backflow Prevention Assemblies Board
More informationLEATHER - CUTTING AND CLOSING Perform specialist footwear closing operations
1 of 5 level: 2 credit: 9 planned review date: November 2005 sub-field: purpose: entry information: accreditation option: moderation option: special notes: Footwear and Leather Trades People credited with
More informationMaintain amenity trees and shrubs
Page 1 of 5 Maintain amenity trees and shrubs Level 3 Credits 8 Purpose People credited with this unit standard are able to: control weeds and ground cover under amenity trees and shrubs; describe irrigation
More informationInstruct a programme using low ropes course activities
Page 1 of 5 Instruct a programme using low ropes course activities Level 5 Credits 5 Purpose People credited with this unit standard are able to: prepare for instructing low ropes course activities; instruct
More informationThis qualification is expiring. The last date to meet the requirements is 31 December 2010.
NQF Ref 0209 Version 5 Page 1 of 11 National Certificate in Civil Construction Supervision with optional strands in Demolition; Drainage; Earthworks; Survey and Set Out; High Capacity Highways; Road Construction;
More informationSet up, repair and maintain a Baader BA 190 fish filleting machine
Set up, repair and maintain a Baader BA 190 fish filleting machine 17949 version 3 Page 1 of 6 Level 6 Credits 50 Purpose People credited with this unit standard are, for a Baader BA 190 fish filleting
More informationSet up, repair and maintain a Baader BA 212CK fish filleting machine
Page 1 of 5 Set up, repair and maintain a Baader BA 212CK fish filleting machine Level 6 Credits 50 Purpose People credited with this unit standard are, for a Baader BA 212CK fish filleting machine, able
More informationContents. Page. Moderator Guide, Ed. 1, June 2011 Page i
Contents Page Introduction... 1 Purpose of this Guide... 1 Moderation... 3 What is Moderation?... 3 Benefits of Moderation... 3 What do Moderators Do?... 4 What Makes an Effective Competenz Moderator?...
More informationRemove and repair perforated non-structural body panel corrosion damage
Page 1 of 5 Remove and repair perforated non-structural body panel corrosion damage Level 3 Credits 3 Purpose This unit standard is for people who work in the motor body industry. People credited with
More informationPUBLIC SECTOR COMPLIANCE MANAGEMENT Audit quality management systems for compliance with weights and measures legislation
1 of 6 level: 6 credit: 13 planned review date: December 2006 sub-field: purpose: entry information: accreditation option: moderation option: Public Sector Services People credited with this unit standard
More informationThis Programme is designed to help students take the next step in their careers and gain more specialist knowledge in their chosen strand.
New Zealand Diploma in Business (with strands in Accounting, Administration & Technology, Leadership & Management, Māori Business & Management, Real Estate) (Level 6) This Programme is designed to help
More informationJACKSON COUNTY WATER AND SEWERAGE AUTHORITY. Cross-Connection Control Program
JACKSON COUNTY WATER AND SEWERAGE AUTHORITY Cross-Connection Control Program 2013-03-14_Policy Document, Cross-Connection Control Program, Rev 1, 2016-5-12.DocxPage 1 of 12 Pages Rev. 1, 5/12/2016 Cross-Connection
More informationAustralian/New Zealand Standard
AS/NZS 1547:2012 AS/NZS 1547:2012 Australian/New Zealand Standard On-site domestic wastewater management AS/NZS 1547:2012 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee
More informationTrainee Assessment Assess risk, develop risk management strategies, and prepare a risk management plan within a health organisation
Trainee Assessment Assess risk, develop risk management strategies, and prepare a risk management plan within a health organisation US 18686 V2 Level 5 Credits 6 Name Trainee assessment This trainee assessment
More informationDemonstrate knowledge of the fundamentals of power system earthing
Page 1 of 5 Demonstrate knowledge of the fundamentals of power system earthing Level 7 Credits 15 Purpose People credited with this unit standard are able to: compile an explanation on the purpose of earthing;
More information; WATERMAINS SPECIFICATIONS FOR CROSS CONNECTIONS and BACKFLOW PREVENTION SECTION C5.0
2016.30; WATERMAINS SPECIFICATIONS FOR CROSS CONNECTIONS and BACKFLOW PREVENTION SECTION C5.0 1. General 1.1. Background: The United States Congress enacted the Safe Drinking Water act (PL 93-532) into
More informationSECTION CROSS CONNECTION CONTROL AND BACKFLOW PREVENTION
SECTION 22 11 16.13 CROSS CONNECTION CONTROL AND BACKFLOW PREVENTION PART 1: GENERAL 1.01 SUMMARY A. This Section includes water-distribution backflow prevention products and installation specifications.
More informationQualification details
Qualification details Title New Zealand Certificate in Refrigeration and Air Conditioning (Trade) (Level 4) Version 1 Qualification type Certificate Level 4 Credits 280 NZSCED 031315 Engineering and Related
More informationBackflow Prevention. Ohio EPA Rules Update. RCAP/Ohio AWWA Small Systems Operator Training May 24, 2016
Backflow Prevention Ohio EPA Rules Update RCAP/Ohio AWWA Small Systems Operator Training May 24, 2016 Maria Lucente, P.E. Ohio Environmental Protection Agency Division of Drinking and Ground Waters Backflow
More informationWater Services Guidelines
Water Services Guidelines Updated Water Services Guidelines Page 1 TABLE OF CONTENTS 1. Purpose of The Service Standards... 2 2. New Service Connections... 2 3. Water Service During Building Construction...
More informationNSW Plumbing and Drainage Regulations. National Backflow Prevention Conference 28 th July 2016
NSW Plumbing and Drainage Regulations National Backflow Prevention Conference 28 th July 2016 Key topics for discussion are; Plumbing and drainage regulation in NSW Consistent regulation approach Codes
More informationLevel 3 NVQ Diplomas in Electrotechnical Technology (2357) Qualification handbook for centres
Level 3 NVQ Diplomas in Electrotechnical Technology (2357) Qualification handbook for centres www.cityandguilds.com December 2010 Version 3.3 (November 2012) About City & Guilds As the UK s leading vocational
More informationNZQA unit standard version 5 Page 1 of 5. Attach, lift, move, and place loads using mobile plant
Page 1 of 5 Title Attach, lift, move, and place loads using mobile plant Level 3 Credits 10 Purpose People credited with this unit standard are able, using mobile plant, to: prepare for a lift; select
More informationSec. T. - Cross connection control.
(Ord. No. O-98-1133, 1, 1-5-99) Sec. T. - Cross connection control. Part 1 1:01. Definitions. For the purpose of this ordinance, the following definitions shall apply unless the context clearly indicates
More informationAustralian/New Zealand Standard
AS/NZS 1546.2:2008 AS/NZS 1546.2:2008 Australian/New Zealand Standard On-site domestic wastewater treatment units Part 2: Waterless composting toilets AS/NZS 1546.2:2008 This Joint Australian/New Zealand
More informationLevel 2 Certificate/Diploma for Sustainable Waste Management Operative (0746)
Level 2 Certificate/Diploma for Sustainable Waste Management Operative (0746) Qualification handbook for centres www.cityandguilds.com August 2017, Version 3.1 General Route (0746-20) (600/0646/8) Waste
More informationP80 06/ ; IRC P
2. Add standard to Chapter 13 as follows: ASSE 1061 06 Performance Requirements for Removable and Non Removable Push Fit Fittings 1. P2904.9.1.4.2 Mechanical joints. Mechanical joints shall be installed
More informationLevel 3 Certificate for Traffic Office ( )
Level 3 Certificate for Traffic Office (3438-02) Qualification handbook 501/2233/2 www.cityandguilds.com May 2011 Version 1.2 (July 2011) About City & Guilds As the UK s leading vocational education organisation,
More informationLevel 3 Certificate, Subsidiary Diploma, 90-Credit Diploma, Diploma, Extended Diploma in Agriculture ( )
Level 3 Certificate, Subsidiary Diploma, 90-Credit Diploma, Diploma, Extended Diploma in Agriculture (0073-03) Qualification handbook for centres 500/8488/4 500/8388/0 600/6048/7 500/8487/2 500/8490/2
More informationKe Kelit NZ. KELEN Australasian Technical Specification
Ke Kelit NZ KELEN Australasian Technical Specification Contact: Adam Lett General Manager, Ke Kelit New Zealand Ke Kelit NZ This document and its contents remain the property of Ke Kelit NZ. Any unauthorised
More informationCross-Connection Control Program. Manual of Procedures
Cross-Connection Control Program Manual of Procedures Revised October, 2006 Table of Contents Introduction.. 2 Definitions. 3 Responsibilities.6 General Requirements... 7 I. Containment Cross-Connection
More informationTIMBERLAKE IMPROVEMENT DISTRICT Jones Rd, Suite 120, Houston, Texas Phone Number (281)
TIMBERLAKE IMPROVEMENT DISTRICT 12841 Jones Rd, Suite 120, Houston, Texas 77070 Phone Number (281) 897-9100 Welcome to your Water District, Timberlake Improvement District, The District. The District is
More informationMODERATOR APPLICATION FORM
MODERATOR APPLICATION FORM 1. PURPOSE This Guide has been developed to assist constituent moderators to prepare for and apply for registration with the SASSETA ETQA. The SASSETA registers assessors and
More information