CERTIFICATE OF FIRE APPROVAL

Transcription

1 LR CERTIFICATE OF FIRE APPROVAL This is to certify that The product detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations and with the International Convention for the Safety of Life at Sea, (SOLAS), 974, as amended, for use on ships and offshore installations classed with Lloyd s Register, and for use on ships and offshore installations when authorised by contracting governments to issue the relevant certificates, licences, permits etc. Manufacturer Halton Marine Oy Address Pulttikatu 2 FI-5700 Lahti Finland Type FIRE DAMPER (STANDARD FIRE TEST) Equipment Description Single / Multi Bladed Rectangular Fire Dampers Type: "FDA" for use in steel bulkheads and decks Specified Standard IMO Res.MSC.307 (88) - (200 FTP Code) Part 3 The attached Design Appraisal Document forms part of this certificate. This certificate remains valid unless cancelled or revoked, provided the conditions in the attached Design Appraisal Document are complied with and the equipment remains satisfactory in service. of issue 9 February 207 Expiry date 8 February 2022 Certificate No. SAS F70023 Signed Office Lloyd's Register EMEA Sheet No of 5 Name K. Taylor Surveyor to Lloyd s Register EMEA A Member of the Lloyd s Register Group Note: This certificate is not valid for equipment, the design or manufacture of which has been varied or modified from the specimen tested. The manufacturer should notify Lloyd s Register of any modification or changes to the equipment in order to obtain a valid Certificate. Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as the 'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract.

2 2 of 5 SAS F February 207 This Design Appraisal Document forms part of the Certificate. APPROVAL DOCUMENTATION. TÜV Eesti OÜ, Maardu, Estonia, Test Report No TD-IMO, dated 03 February Drawing No. JpM50642, Rev. 02, dated 0 June TÜV Eesti OÜ, Maardu, Estonia, Test Report No. 56-5TD-IMO, dated 9 February Drawing No. JpM50793, Rev. 02, dated 0 June TÜV Eesti OÜ, Maardu, Estonia, Test Report No TD-IMO, dated 06 April Drawing No. Sal50047, dated 04 January TÜV Eesti OÜ, Maardu, Estonia, Test Report No TD-IMO, dated 08 April Drawing No. Sal50057, Rev. 0, dated 2 January TÜV Eesti OÜ, Maardu, Estonia, Test Report No. 64-6TD-IMO, dated 0 August Drawing No. JpM6003, Rev. 03, dated 0 February 206. VTT Expert Services Ltd, Lahti, Finland, Test Report No. VTT-S , dated 0 March Drawing No. Sal50056, dated 05 January VTT Expert Services Ltd, Lahti, Finland, Test Report No. VTT-S , dated 09 May Drawing No. Sal60059, Rev. 03, dated 0 February VTT Expert Services Ltd, Lahti, Finland, Test Report No. VTT-S , dated 4 January Drawing No. JpM50730, Rev. 02, dated 23 September VTT Expert Services Ltd, Lahti, Finland, Test Report No. VTT-S , dated February Drawing No. JpM50905, Rev. 0, dated 23 September 205 CONDITIONS OF CERTIFICATION. For applications in A-0, A-5, A-30 and A-60 Class steel bulkheads and decks with both the ducting and fire damper suitably insulated in accordance with Conditions 9 and 0 below 2. Minimum and maximum size of damper: 200mm x 200mm up to 200mm x 600mm 3. Maximum modular arrangement size: 2500mm x 2600mm 4. Single or Multi-Bladed fire dampers 270mm deep with outer casing composed of at least 3mm thick stainless steel. 250mm or 200mm high blades are comprised of stainless steel or galvanised steel mm with a double skin hollow profile of total thickness 2mm 5. Modular fire damper arrangement consisted of 4 modules of FDA 200mm x 250mm fire dampers with 00mm wide x 270mm deep stainless steel mullions and framework of which the fire dampers are bolted to in accordance with Condition 6 below 6. Fire dampers are bolted to the steel coamings with M0 bolts at 50mm maximum spacing

3 3 of 5 SAS F February To be fitted with 'Sealfire W200' gaskets between the fire damper and the coaming or an equivalent fire rated product meeting Part 3 of the 200 IMO FTP Code 8. The fire dampers may be operated by fusible links by the actuators dependent upon damper sizer and mode of actuation as per Table below: Table Types: Fire Damper Type FDA 200mm x 600mm FDA 300mm x 300mm FDA 200mm x 200mm FDA 2500mm x 2600mm (Multi-Blade Modular Arrangement) Pneumatic s Electrical s Bulkheads Decks Bulkheads Decks Rotork Rotork GTWSM.0x90 N/A N/A GTWSM.0x90 Air Torque AT35U AirTorque AT30 S2B / PT35U S2B / PT30 s s Schischek Ex-Max- 5-SF / RedMax- 5-SF / InMax-5- SF s Air Torque AT04 / PT04 s AirTorque AT350 / PT350 s AirTorque SB AT04 S2 / PT04 S2 s Festo DAPS RS4-F0305-CR Air Torque AT0 / PT0 s Rotork GTWSM.63x90.K2 NP2A F05-F07 60 Elodrive CSQP-5AE Belimo BF-230 N/A N/A N/A N/A Schischek Ex-Max-5-SF / RedMax-5-SF / InMax-5- SF s Belimo NF24A-SR Belimo BF230-2 HL 9. For use in A-0, A-5, A-30 and A-60 Class Bulkheads as shown in Table 2 below, the fire damper should be insulated with an approved A-60 insulation system and the coaming and ducting should be insulated with an approved insulation system to the same rating as the bulkhead, for the total insulated lengths specified in Table 2 below, which may be interpolated for intermediate sizes based on the internal cross-sectional area of the duct. Reference is also made in Table 2 below to the corresponding approval document listed above which shows the corresponding insulation arrangements Table 2 Minimum Duct Insulation Lengths (Including Fire Damper) for Bulkhead Applications: Fire Rating FDA 200mm x 600mm A-0 No insulation on duct A-5 No insulation on duct No insulation on duct FDA 2500mm x 2600mm (4 x FDA 200mm x 250mm) (Multi-Blade Modular)

4 4 of 5 SAS F February 207 A-30 Fire FDA 200mm x Rating 600mm A-60 Length: 350mm* OR Length: 885mm Ref. 8] Length: 200mm* Length: 200mm* FDA 2500mm x 2600mm (4 x FDA 200mm x 250mm) (Multi-Blade Modular) 650mm** Ref. 0] * Additional 280mm insulation on the unexposed side was applied on the coaming near the bulkhead forming a total thickness of 20mm (60mm + 60mm) of insulation. ** Additional 550mm insulation on the fire exposed side was applied on the coaming near the bulkhead forming a total thickness of 85mm (60mm + 25mm) of insulation 0. For use in A-0, A-5, A-30 and A-60 Class Decks as shown in Table 3 below, the fire damper should be insulated with an approved A-60 insulation system and the coaming and ducting should be insulated with an approved A-60 insulation system to the same rating as the deck, for the insulated lengths specified in Table 3 below, which may be interpolated for intermediate sizes based on the internal cross-sectional area of the duct. For A-0 applications no insulation needs to be fitted to the steel ducting. Reference is also made in Table 3 below to the corresponding approval document listed above which shows the corresponding insulation arrangements Table 3 Minimum Duct Insulation Lengths (Including Fire Damper) for Deck Applications: Fire Rating FDA 200mm x 600mm A-0 No insulation required on duct or coaming. Ref. 2] No insulation required on duct. Ref. 2] No insulation required on duct. Ref. 2] A-5 As per A-30 As per A-30 A mm Ref. 4] 805mm Ref. 4] A mm*** Ref. 4] OR 00mm**** Ref. 6 & Ref. 8] 900mm Ref. 6 & Ref. 8] 900mm Ref. 6 & Ref. 8]

5 LR Lloyd s Register EMEA 5 of 5 SAS F February 207 *** Additional 60mm insulation on the upper side was applied on the to the base of the coaming for 60mm forming a total thickness of 20mm (60mm + 60mm) of insulation. **** Additional 60mm insulation on the upper side was applied on the to the base of the coaming for 200mm on the underside of the deck and 200mm on the upper side of the deck forming a total thickness of 20mm (60mm + 60mm) of insulation. Production items are to be manufactured in accordance with a quality control system which shall be maintained to ensure that items are of the same standard as the approved prototype PLACES OF PRODUCTION Halton Marine Oy Pulttikatu 2 FI-5700 Lahti Finland Halton Ventilation (Shanghai) Co. Ltd 600 South Xin Yuan Road / Building 0 Lingang New City, Pudong Shanghai People s Republic of China Halton Company 0 Industrial Drive Scottsville KY 4264 USA Office Lloyd's Register EMEA Keith Taylor Senior Specialist Aberdeen Technical Support Office Marine & Offshore Lloyd s Register Supplementary Type Approval Terms and Conditions This certificate and Design Appraisal Document relates to type approval, it certifies that the prototype(s) of the product(s) referred to herein has/have been found to meet the applicable design criteria for the use specified herein, it does not mean or imply approval for any other use, nor approval of any products designed or manufactured otherwise than in strict conformity with the said prototype(s).