natural smoke and heat exhaust systems

Transcription

1 natural smoke and heat exhaust systems mcr PROLIGHT smoke vents and continuous rooflights mcr LAM louvered smoke vents mcr PROSMOKE smoke curtains

2 mcr PROLIGHT SMOKE VENTS STRUCTURE Base natural smoke and heat exhausting air supply daily ventilation additional lighting Made of galvanised steel sheet or aluminium, cm high, with thermal insulation as standard (bases without insulation are also available), adapted for treatment with roofing paper or a PVC membrane, can also be supplied with flashings for mounting on a roof made of corrugated sheet or adjusted to be fixed on an existing plinth (application mainly in case of renovations). Leaf Steel frame with a cellular polycarbonate filling, acrylic or polycarbonate dome or a solid panel not transmitting light. Single or double leaf vents are available. Control Pneumatic, electric or mechanical systems. FEATURES OF THE mcr PROLIGHT SMOKE VENTS optimised aerodynamic areas - up to 6,66 m2 per device* large series of types: single-leaf vents: minimum dimensions: 100 x 100cm, maximum dimensions: 200x250 cm double-leaf vents: minimum dimensions: 120 x 160 cm, maximum dimensions: 300 x 300 cm vents are delivered fully assembled to site and are ready to be mounted * For the DVP 300/300 vent with deflectors, inlet deflectors and base 50 cm high.

3 mcr PROLIGHT COUNTINUOUS ROOFLIGHTS STRUCTURE Base Made of galvanised steel sheet, cm high, without thermal insulation. Dome Aluminium profiles with a cellular polycarbonate filling. Integrated smoke vents or ventilation flaps Single or double leaf vents with pneumatic or electric control systems. smoke and leaf exhausting daily ventilation additional lighting FEATURES OF THE mcr PROLIGHT ROOFLIGHTS hight quality products ensuring the supply of additional light to interiors wide selection of dimensions: rooflights of cm in width and of unlimited length it is possible to integrate smoke vents or ventilation flaps of the following dimensions: single-leaf vents: minimum dimensions: 100 x 100 cm maximum dimensions: 200 x 250 cm double-leaf vents: minimum dimensions: 100 x 100 cm maximum dimensions: 250 x 250 cm simple and quick assembly: rooflights are delivered to a construction site in a form of ready-to-assemble elements which can be mounted on one's own (Mercor provides technical support, if needed)

4 mcr PROSMOKE SMOKE CURTAINS TYPES mcr PROSMOKE S fixed curtain mcr PROSMOKE CE automatic rolling curtain mcr PROSMOKE FS automatic rolling curtain with a "fail safe" option STRUCTURE OF AUTOMATIC CURTAINS steel casing grey non-combustible fabric roller electric drive bottom bar comfort bottom bar STRUCTURE OF STATIC CURTAINS load-carrying (supporting) steel profile pressing steel profile grey non-combustible fabric bottom bar optimised smoke control accumulation of smoke and hot gases compartments improvement of smoke vent's effectiveness in FEATURES OF THE mcr PROSMOKE CURTAINS distinguished fire resistance parameters (DH30-DH60, D30-D180) possibility of covering openings of any width variety of possibilities of fixing the curtains to the ceiling and joining modules together simple installation, low load for a structure

5 mcr LAM LOUVERED SMOKE VENTS natural smoke and heat exhausting air supply daily ventilation additional lighting FEATURES OF THE mcr LAM SMOKE VENTS STRUCTURE Base Made of galvanised steel sheet or aluminium, cm high. Base can be equipped with a wide range of flanges to suit all curbs, sheeting and glazing applications. Blades optimised aerodynamic areas - up to 6,18 m 2 per device* vast range of sizes: minimum size of the mcr LAM vent is 80 x 50 cm maximum size of the mcr LAM vent is 380 x 250 cm they can be installed on roofs of any inclination or in facades while open, thet are high resistant to wind low consumption of electric energy or compressed gas by control elements they ensure security of property: no access to the building through open vent the guaranteed safety of people working on the roof, protection against impact of soft large body (1200 J) * mcr LAM of size 380 x 250 cm equipped with wind deflectors Made of aluminium profiles with panels of cellular polycarbonate 16 mm thick (transparent or opal) as well single skin aluminium (not insulated) or double skin aluminium (insulated with XPS). Control Pneumatic or electric system. Set of wind deflectors in every smoke roof vent, which is installed on the roof. Rain shield optional (for louvers mounted in facade).

6 FIRE PROETECTION SYSTEMS smoke and heat exhaust systems fire ventilation systems fire protection of building structures NATURAL SMOKE AND HEAT EXHAUST SYSTEMS comprehensive solutions for smoke and heat exhausting protection of escape routs against smoke reduction of material losses caused by fire and smoke supply of light and fresh air to building interiors Mercor SA ul. Grzegorza z Sanoka Gdańsk tel fax mercor@mercor.com.pl