Bill of Quantity (BOQ)
|
|
|
- John Wilkinson
- 5 years ago
- Views:
Transcription
1 Bill of Quantity (BOQ) PART-I : FIRE FIGHTING SYSTEM. Sr No Description Qty Unit Rate/Unit Amount 1 Dismantling, loading, shifting and unloading of following Fire Fighting Equipments from Berth No.8 to Berth No.7 (Port provide crane and truck) as per Technical Specification. (a) Monitor Pump (11000 LPM) with Diesel Engine (650 HP) 02 Nos (b) Hydrant Pump (6500 LPM) with Diesel Engine (255 HP) 01 Nos (c) Jockey Pump 02 Nos 2 Design, supply of Ground Monitor with isolation valve on 3 m high RCC Tower with all insert plates, fixtures, clamps, SS fasteners, pressure gauge dial type 150 mm size connected at monitor inlet pipe and supporting for riser pipe and monitor, orifice plates suitable to discharge 3000 LPM capacity at 8kg/cm² with a horizontal throw range of 60 m with electrical/electro hydraulic equipments for horizontal and vertical rotation with base operation control etc. and shall be capable of being remote controlled etc. and complete in all respects, as per Technical Specification. 02 Nos
2 3 Design, supply of SS 316 size 63 mm Double Headed Standard Fire Hydrants with (landing valves as per BIS:5290) and isolation valve (100 NB), SS-316 with orifice plates to be provided below each hydrant and separate controls fitted with 63 mm instantaneous female coupling on each outlet complete with 2 Nos. hose box with stand of 15 m long hose pipe each with end coupling with nozzles in all respects as per Technical Specification. 04 Nos 4 Design, supply of Jumbo Water Curtains Nozzles with motorized valve, orifice plate producing dense water curtains of 20 m radius, through 180 angle in vertical plane discharging at 362 LPM at an inlet pressure of 8 kg/cm² and complete in all respects. 14 Nos 5 Design, supply, of intrinsically safe Electrical System for Remote Operation of water monitors, main pumps, foam pumps, water curtain system etc. from control room with centralized remote control panel with joystick controls including FRLS control cables and etc. and complete in all respects. 1 Set
3 6 Design, fabrication, supply of Cement Lined (inside) ERW Steel Pipe conforming to BIS:3589 of Grade Fe 410 of not less than 8 mm for carrying sea water including supply of pipes, Excavation, back filling of trench, hume pipe at road crossing (In case of underground pipe).specials, bends, flanges, dummy flanges, gaskets, stainless steel bolts & nuts, washers, miters, bends, tees, reducers, expanders, steel/rcc supports saddles, inserts, fixtures, hume pipe of suitable class including painting 3 coats of approved colour (one coat of zinc-rich primer and two coats of epoxy paint with fire red colour) externally for over ground pipe lines and double coating with double wrapping coating as per IS in case of underground pipeline complete as follows: (a) 250 NB 300 Mtr (b) 200 NB 300 Mtr (c) 100 NB (double galvanized) 200 Mtr (d) 80 NB (double galvanized) 200 Mtr 7 (i) Installation, Testing and Commissioning of following Fire Fighting equipments at Berth No.7 in the proposed pump house as per Technical Specification. (a) Monitor Pump (11000 LPM) with Diesel Engine (650 HP) 02 No (b) Hydrant Pump (6500 LPM) with Diesel Engine (255 HP) 01 No
4 (c) Jockey Pump 02 No (ii) Installation, Testing and Commissioning of Sr No. 2 (Ground Monitor and complete accessories) 02 No (iii) Installation, Testing and Commissioning of Sr No.3 (Double Headed Standard Fire Hydrants and complete accessories) 04 No (iv) Installation, Testing and Commissioning of Sr No.4 (Jumbo Water Curtains Nozzles and complete accessories) 14 No (v) Installation, Testing and Commissioning of Sr No.5 (Intrinsically safe Electrical System and complete accessories) 01 Set (vi) Installation, Testing and Commissioning of Sr No.6 (ERW Steel Pipe and complete accessories) (a) 250 NB 300 Mtr (b) 200 NB 300 Mtr (c) 100 NB (double galvanized) 200 Mtr (d) 80 NB (double galvanized) 200 Mtr TOTAL A
5 PART-II : CIVIL WORKS (PUMP ROOM) Sr No Description Qty Unit Rate/Unit Amount 1 Design and construction of Pump House (Ground + First Floor + Second Floor) of area 10 x 6 = 60 m 2 (approx) 1 LS Total- B
6 Sr No Description Qty Unit Rate/Unit Amount Grand Total ( A +B )
SUMMARY OF PRICES FOR FOR FIRE FIGHTING WORKS FOR Phase-1,(Block-G&H) Type-B
SUMMARY OF PRICES FOR FOR FIRE FIGHTING WORKS FOR Phase-1,(Block-G&H) Type-B Design Centre Consulting Engineers Pvt Ltd, Ghaziabad, NCR Delhi, Tel-0120 4333451, 4333452 Page 1 BILL OF QUANTITIES S. NO.
ENGINEERING PROJECTS (INDIA) LTD., (A Govt. of India Enterprise) PRICE BID
1 ENGINEERING PROJECTS (INDIA) LTD., (A Govt. of India Enterprise) PRICE BID HVAC Works for Construction of New Chemical Sciece Building at IISc Bangalore. Sl.No Description of Item Unit Quantity Rate
PART A : CPVC PIPES AND FITTNGS (EXTERNAL WATERSUPPLY):
PART A : CPVC PIPES AND FITTNGS (EXTERNAL WATERSUPPLY): 01 Providing and Fixing of CPVC pipes confirming to ASTM standard including all CPVC fittings like tees, elbows, bends, unions, coupling, reducer
Description of the Work
Description of the Work Construction,Supplying of Electro Mechanical equipment, pipe fittings, erection, installation, testing and commissioning MBBR technology Sewage Treatment Plant ( 300 KLD) at kh.no.54,city
Plot No. 1-7/B, Laxmi Co-op Industrial Estate, Hatkanangale , Kolhapur Dist. TENDER NO D5
ICHALKARANJI POWERLOOM MEGA CLUSTER LTD., ICHALKARANJI. TAL- HATKANANGLE, DIST- KOLHAPUR. Plot No. 1-7/B, Laxmi Co-op Industrial Estate, Hatkanangale 416 109, Kolhapur Dist. Website www. ichmegacluster.com
No # Specifications Rate To Be Quoted. Unit Qty (in figures) (in words) Total Amount
Revised Schedule B as per corrigendum no. SASB/NIT/Works/818/2016/09 dated 28.01.2016. SCHEDULE B (FINANCIAL BID) B- a FABRICATION AND SUPPLY OF 200 EUROPEAN TYPE TOILETS (Rate to be quoted in Rupees both
Stainless Steel Aeration Equipment Specification
Section 15 Stainless Steel Aeration Equipment Specification Part 1 - General 1.01 Description A. Scope of Work 1. Furnish, install and test aeration system including air mains, drop pipes, valves, expansion
`AMENDMENT No. 4 TO TENDER DOCUMENTS. Tender No.: RITES/CO/B&A/EE/DTEH-Rohtak Air Cooled Chiller System of HVAC work
`AMENDMENT No. 4 TO TENDER DOCUMENTS Tender No.: RITES/CO/B&A/EE/DTEH-Rohtak Air Cooled Chiller System of HVAC work S.No. Clause of tender 1 1) S.H A, Fashion Design BOQ Item no. 1 a.iii), 2) S.H A, Film
SECTION FACILITY POTABLE WATER DISTIBUTION
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 22 11 00 FACILITY POTABLE WATER DISTIBUTION A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification
Design and Construction Standards SECTION POTABLE WATER SYSTEMS
SECTION 15410 POTABLE WATER SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification sections,
SCHEDULE OF QUANTITIES
SCHEDULE OF QUANTITIES 1 FIRE HYDRANT SYSTEM PUMP ( Electrically driven) Supplying, installing, testing & commissioning of electric driven, suitable for autometic operation of horizontal single stage centrifugal
Materials Carbon Steel and Malleable Iron are used in the manufacture of concrete inserts. Stainless Steel and other materials are available.
Concrete inserts offered in this section are designed to provide a pre-set support point in concrete ceilings, walls, and floors. A range of inserts with varying design loads are available. Materials Carbon
SECTION HANGERS AND SUPPORTS FOR PLUMBING
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
BILL OF QUANTITY ENGINEERING & MANAGEMENT CONSULTING CENTRE. "Beit Hanoun Emergency Water Supply Project"
"Beit Hanoun Emergency Water Supply Project" " Rehabilitation and Construction of Beit Hanoun Water Network " BILL OF QUANTITY ENGINEERING & MANAGEMENT CONSULTING CENTRE Bill of Quantities PREAMBLE TO
SECTION FIRE HYDRANTS
SECTION 21 11 10 PART 1. GENERAL 1.1 SUMMARY: A. Work consists of furnishing and installing new fire hydrants, (boot with ductile iron retainer gland, standpipe and hydrant complete) plus constructing
All our products Quality Assurance QUALITY Ensure quality control and it strive for the following:
ALTOWS COMPANY ABOUT US ALTOWS CO. is a premium supplier of top quality piping components and fittings which include various pipes, tubes, threaded fittings, flanges, fasteners, bars, rods etc. Our products
Service Saddles/ Brass Alloy/ Stainless Steel Straps for Cast, Ductile & PVC Pipe
F 1 F 1.1 F 1.2 F 2 F 2.1 F 3 Service Saddles/ Hinged Type for 2 PVC Service Saddles/ Brass Alloy/ Stainless Steel Straps for Cast, Ductile & PVC Pipe Service Saddles/ Ductile Iron/ Stainless Steel Straps
4 1 /2 MARK 73-5 AMERICAN FLOW CONTROL. It s What We Know. AMERICAN-DARLING FIRE HYDRANT AMERICAN-DARLING 4 1 /2 MARK 73-5 FIRE HYDRANT
AMERICAN-DARLING FIRE HYDRANT AMERICAN-DARLING FIRE HYDRANT AMERICAN FLOW CONTROL It s What We Know. CONSTRUCTION AMERICAN-DARLING FIRE HYDRANT OPERATING NUT Cast one-piece bronze operating nut. Design
Improvements to the Distribution Pipe Lines in Zalengi, Central Darfur Please insert the currency Item Description
RETURNABLE BID SCHEDULE 4 BILL OF QUANTITIES Case No. SDPC/76613/WORKS/ITB056 Improvements to the Distribution Pipe Lines in Zalengi, Central Darfur Please insert the currency 1 General 1 Mobilization
PONDICHERRY UNIVERSITY ENGINEERING WING SCHEDULE OF WORK
PONDICHERRY UNIVERSITY ENGINEERING WING SCHEDULE OF WORK Name of the work: Supply, erection and commissioning of 20HP submersible motor pump set at Pondicherry University, Karaikal campus S.No. Description
Arms Group Drainage System. 1. Swivel Joint Type 2. Pivot Joint Type 3. Flexible Hose Type 4. Swing Master Joint Type 5. Floating Check Valve
Arms Group Drainage System 1. Swivel Joint Type 2. Pivot Joint Type 3. Flexible Hose Type 4. Swing Master Joint Type 5. Floating Check Valve Swivel Joint Type Model No. 1010 Sizes 3in through 8in Heavy
CVO/169897A OCTOBER 29, CONVEYANCE PIPING GENERAL
SECTION 02500 CONVEYANCE PIPING - GENERAL PART 1 GENERAL 1.1 REFERENCES A. The following is a list of standards which may be referenced in this section: 1. American Concrete Institute (ACI): 301, Standard
DIVISION 15-MECHANICAL SECTION SUPPORTS AND ANCHORS PN PART 1 - GENERAL 1.01 SECTION INCLUDES. A. Pipe and equipment support systems.
PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe and equipment support systems. B. Inserts. 1.02 RELATED SECTIONS A. Section 15890 - Ductwork Supports. 1.03 DEFINITIONS A. Supports: Attachments, hangers,
Diffused Aeration Piping Equipment
1.0 General 1.1. The specifications in this section include all components of the Diffused Aeration System with the exception of the individual diffuser units. Refer to additional specification sections
MAHINDRA WORLD CITY AT JAIPUR
MAHINDRA WORLD CITY AT JAIPUR TENDER DOCUMENT FOR SOFTENING SYSTEM Architects RKA ASSOCIATES B-6/17, SHOPPING CENTER SAFDARJUNG ENCLAVE NEW DELHI-110029. Consultants KKA ASSOCIATES D_139, SAKET NEW DELHI-110017
2 5 0 P. S. I. G. AMERICAN DARLING 5 1 /4" B-84-B FIRE HYDRANT
2 5 0 P. S. I. G. AMERICAN DARLING 5 1 /4" B-84-B FIRE HYDRANT CONSTRUCTION OPERATING NUT-cast one piece bronze operating nut. Design of the operating thread permits slow closing of the hydrant valve,
Standard Tube & Pipe Adapters
Standard Tube & Pipe Adapters 1 to 8 OD Tube Sizes, 1 to 8 NPS Pipe Sizes Aluminum, Stainless Steel, Carbon Steel, Galvanized (Zinc-Coated) Steel. 11, 14, 16 Gauge Tube Wall Thicknesses; Schedule 5, 10,
AMERICAN DARLING 5 1 /4" B-62-B FIRE HYDRANT
AMERICAN DARLING 5 1 /4" B-62-B FIRE HYDRANT CONSTRUCTION PIPE PLUG-provides access to lubrication chamber. Pipe plug can be replaced with lubricating fitting to lubricate the rod threads and thrust washers.
NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PIPE HANGERS, Section PIPE HANGERS, SUPPORTS, AND RESTRAINTS
PART 1 GENERAL 1.01 SUMMARY Section 15140 PIPE HANGERS, This Section includes the furnishing and subsequent installation of: A. Pipe and equipment hangers, supports, and associated anchors B. Equipment
d.p. Consulting Engineers, Inc.
d.p. Consulting Engineers, Inc. 3727 Doctors Drive Port Arthur, Tx 77642 Phone: 409-983-6263 Fax : 409-983-6265 Firm Registration No: F-3356 Email : dp@dpengineersinc.com ADDENDUM NO. 1 ADDENDUM ISSUE
A Provide for Contractor's Office, Store etc. Sum
BILL NO.1 - PRELIMINARIES AND GENERAL CONDITIONS A Provide for Contractor's Office, Store etc. Sum B C Provide for Insurance in accordance with the Conditions of the Contract. Allow for the provision of
SR.NO. PARTICULARS QTY. UNIT. New Cooling Tower - for Chiller Plant
A New Cooling Tower - for Chiller Plant 1 Supply, Installation, Testing & Commissioning of New Cooling Tower - Advance make, Induced draft counter flow, Model No. 4RM-73 or equivalent approve make as mention
Underground Exhaust System
Operation and Maintenance Manual Underground Exhaust MONOXIVENT - SOURCE CAPTURE SYSTEMS - info@ Oct. - 2015 Underground Duct Construction Standards 1. Dig trench depth to allow for minimum distance from
1.1 SECTION INCLUDES.1 Materials and installation for water mains, hydrants, valves, valve boxes, and valve chambers, including service connections.
Issued 2005/06/01 Section 02511 Water Mains Page 1 of 10 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Materials and installation for water mains, hydrants, valves, valve boxes, and valve chambers, including service
40'-0" PIPE SUPPORT (TYP.) (SEE DWG. NO. SK-2 OR DWG. NO. SK-4)
SK-1 STANDARD LENGTH 4.301 40'-0" A 6" 2'-0" 9'-0" 9'-0" 9'-0" 9'-0" 2'-0" A 3" OF EXPOSED AT EACH END OF PIPE. PIPE SUPPORT (TYP.) (SEE DWG. NO. SK-2 OR DWG. NO. SK-4) EXPOSED PIPE MINIMUM GAUGE AND THICKNESS
SECTION HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS
SECTION 26 05 29 HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide all labor, materials, equipment, and incidentals as shown, specified, and
KENT COUNTY WATER AUTHORITY. ERRATUM to Rules and Regulations of the Kent County Water Authority
KENT COUNTY WATER AUTHORITY ERRATUM to Rules and Regulations of the Kent County Water Authority Section 4.9.1.1 Resilient Seat Gate 4 inch to 12 inch: Replace with the attached. Section 4.9.1.3 Tapping
MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 22 PLUMBING
SECTION 221316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following soil and waste, sanitary drainage and vent piping inside the building: 1. Pipe, tube,
TECHNICAL 1. INTRODUCTION
TECHNICAL 1. INTRODUCTION The ensuing Technical Specifications are for the Refurbishment of Fire Fighting system Installation at BHARAT PETROLEUM CORPORATION LTD SOUTHERN REGIONAL OFFICE & RESIDENTIAL
OLYMPIC VIEW WATER AND SEWER DISTRICT APPROVED MATERIALS LIST FOR USE ON NEW CONSTRUCTION OF WATER AND SEWER FACILITIES
OLYMPIC VIEW WATER AND SEWER DISTRICT APPROVED MATERIALS LIST FOR USE ON NEW CONSTRUCTION OF WATER AND SEWER FACILITIES This form is intended for use by developers or contractors constructing potable water
NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 1316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
RUWAIS HOUSING COMPLEX PHASE IV CIVIL & ELECTROMECHANICAL WORKS
AL NASR SCOPE OF WORKS: Construction of water storage tank consisting of: 3 Water storage tanks 2,641,721 gal of 42 m diameter and 7.65 m each 2300 m³ of concrete 2450 m² of water proofing external 4300
A. Codes and Standards that are standard at the University. C. Coordinate cleanout locations with Architect.
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
SECTION C1 DUCTILE IRON PIPE AND FITTINGS GENERAL
SECTION C1 DUCTILE IRON PIPE AND FITTINGS GENERAL This section covers the furnishing and installation of ductile iron water pipe, fittings, thrust restraint and pipe disinfection. Ductile Iron Pipe MATERIALS
Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC PIPES AND TUBES
SECTION 23 20 00 - HVAC PIPES AND TUBES PART 1 - GENERAL 1.1 SUMMARY: A. Section includes pipe and pipe fittings for: heating water, chilled water, steam and steam condensate, condenser water, glycol,
SUPPORT AND ANCHORS SECTION 15090
SUPPORT AND ANCHORS SECTION 15090 PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. Work included in this Section: Materials, equipment, fabrication, installation and tests in conformity with applicable codes
PURCHASE SPECIFICATION Rev. 02 Erection & Supply of Valves. Piping & Testing Dt.30/07/10 For the Pump Test Rig (Refer Dwg. No RD DG )
PRE QUALIFICATION: The Vendor should have earlier experience in carrying out such Jobs and should give reference for the same. The work is to be done in BHEL R&D premises. The responsibility of safety
Nairobi Funeral Home and Forensics INCINERATOR BILLS OF QUANTITIES
Nairobi Funeral Home and Forensics INCINERATOR BILLS OF QUANTITIES 26/10/2015 Item Description Qty Unit INCINERATOR INSTALLATION Supply, deliver, install, test and commission the following incinerator
SECTION PLUMBING SPECIALTIES
SECTION 15430 PLUMBING SPECIALTIES PART 1 GENERAL The requirements of the GENERAL CONDITIONS, SUPPLEMENTARY CONDITIONS and Division 1, General Requirements, Apply to the work specified in this section.
Essex County College - West Essex Campus Addition And Renovations dlb # / SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
TECHNICAL SPECIFICATION DANTECO HERMANNS. CONTAINER FOR BULK POWDER Equipped with HERMANNS Aeration and Conveyance Device
TECHNICAL SPECIFICATION DANTECO HERMANNS CONTAINER FOR BULK POWDER Equipped with HERMANNS Aeration and Conveyance Device 6058(20') x 2438(8') x 2591(8'6") MODEL NO. : CX09-20SNX1 SPEC. NO : CX09-20SNX1-S3
भ रत य प रब धन स स थ न न गप र
भ रत य प रब धन स स थ न न गप र INDIAN INSTITUTE OF MANAGEMENT NAGPUR Tender No : IIMN/CAO/12/2018-19 dated 30-08-2018 Name of Work :Provision of toilet, extension of washing shade and Stainless steel railing
3. Intermediate metal conduit (IMC). 4. Electric metallic tubing (EMT). 5. Flexible metal conduit (FLEX). 6. Polyvinyl chloride conduit (PVC).
SECTION 16111 CONDUITS PART 1 - GENERAL 1.01 DESCRIPTION A. General: Provide conduits, complete, as shown, specified or required per Contract Documents. Principal items include: 1. Rigid aluminum conduit.
1470 Dale Court Austell, GA Phone: Fax:
1470 Dale Court Austell, GA 30168 Phone: 404-351-2202 Fax: 404-351-2203 LC METALS, INC. PRODUCT INDEX Page # STUD GUARDS...3 FHA STRAPS...3 BOCA PLATES (Nail Plates)...4 PLUMBERS TAPE (Banding Iron)...4
0.75 " transparent hose w/ valve for head measurements fixed to screws 20 MIL PVC liner. 6" gate valve
0.75 " transparent hose w/ valve for head measurements fixed to screws 250x1000 RC beam 6" gate valve Foundation preparation in accordance with technical specifications and as approved by engineer 25 cm
Copper-Type K soft Drawn 40, 50 HDPE 100 and larger
1.0 GENERAL 1.1 Scope 1.1.1 The work covered by this section involves the installation of water and sewer service connections and all other associated work. 1.2 Authorization 1.2.1 Do not install service
STANDARD TECHNICAL SPECIFICATION FOR ROTAMETER VOLUME - IIB. SPECIFICATION No: PE-SS I010
STANDARD TECHNICAL SPECIFICATION FOR ROTAMETER VOLUME - IIB SPECIFICATION No: PE-SS-999-145-I010 BHARAT HEAVY ELECTRICALS LIMITED POWER SECTOR PROJECT ENGINEERING MANAGEMENT DIVISION NOIDA, INDIA SPECIFICATION
September 6, 2016 Page 1 of 5
September 6, 2016 Page 1 of 5 1. SECTION 16100 Drawing E4.3, Note #39: Reference to the radio fire alarm panel and the fire station alerting master panel does not relate to the building fire alarm system.
CITY OF FARGO SPECIFICATIONS SEWER AND WATER SERVICE CONNECTIONS
SEWER AND WATER SERVICE CONNECTIONS PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of the furnishing of all labor, material,
EXPRESSION OF INTEREST (EOI) FOR. Mechanical Works
EXPRESSION OF INTEREST (EOI) FOR Mechanical Works KWtE-03-PR-EO-ACC-0 Rev01 15 Version: Date: Prepared by: Approved: 01 7/11/18 VMC AMN Page 1 OF 6 1 Project overview ACCIONA s Engineering, Procuring &
STATEMENT OF WORK. Refurbishment of the cooling system of the Nuclear Research Reactor at the Nuclear Center "Dr. Nabor Carrillo Flores".
STATEMENT OF WORK Refurbishment of the cooling of the Nuclear Research Reactor at the Nuclear Center "Dr. Nabor Carrillo Flores". Page 1 of 8 STATEMENT OF WORK 1. Introduction This Statement of work (SOW)
Ref:. CESU.H.Qrs./P&S/Capex-Turnkey/527/12-13/ Dt CORRIGENDUM - I
CENTRAL ELECTICITY SUPPLY UTILITY OF ODISHA Regd. Office: 2 nd Floor, IDCO TOWERS, Bhubaneswar-751022 Phone- (0674)2541727, 2543721, Fax: (0674)2543125 Web Site: www.cesuodisha.com Ref:. CESU.H.Qrs./P&S/Capex-Turnkey/527/12-13/
WATER 6.1 GUIDELINES
6-1 6.0 WATER 6.1 GUIDELINES The requirements of the Queensland Water Resources Commission Guidelines for Planning and Design of Urban Water Supply Schemes shall be followed in general. The requirements
Rosemount 405 Compact Orifice Primary Element
Rosemount 405 Compact Orifice Primary Element SPECIFICATIONS Performance Discharge Coefficient Uncertainty TABLE 20. 405 Compact Orifice Primary Element Type 405C (Conditioning Compact) 405P (1)(2) (Standard
CITY OF WARRENVILLE STANDARD SPECIFICATIONS WATER MAIN, SANITARY SEWER AND STORM SEWER
CITY OF WARRENVILLE STANDARD SPECIFICATIONS WATER MAIN, SANITARY SEWER AND STORM SEWER WATER MAIN 1. All open cut water main shall be polyvinyl chloride plastic (PVC) pressure pipe per AWWA specification
HAWLE-range of products
HAWLE-pRODucTS All OvER ThE world since 1948 HAWLE-range of products HAWLE subsidiaries HAWLE partners Illustrations, technical data, dimensions and weights are subject to alteration without notice. Edition
BOQ for Plumbing, Sanitary Works
BOQ for Plumbing, Sanitary Works Page of 6 Sr.No Item Description Quantity Unit Rate Amount (Rs.) SANITARY FIXTURES a Providing & Fixing star white colour vitreous china wall mounted wc with heavy duty
OLYMPIC VIEW WATER AND SEWER DISTRICT APPROVED MATERIALS LIST FOR USE ON NEW CONSTRUCTION OF WATER AND SEWER FACILITIES
OLYMPIC VIEW WATER AND SEWER DISTRICT APPROVED MATERIALS LIST FOR USE ON NEW CONSTRUCTION OF WATER AND SEWER FACILITIES This form is intended for use by developers or contractors constructing potable water
Borehole Pumps Best Practises
Borehole Pumps Best Practises When it has been identified that water should be abstracted for any reasons a Scope of Work should be developed. 1. Essential Steps when determining Scope. - Determine the
N-pump, Standard Motor
N-pump, Standard Motor N-pump, Standard Motor Product description Usage Installation type P, S, T, Z Installation type L A submersible pump for efficient pumping of clean water, surface water, and wastewater
A. Codes and Standards that are Standards at the University. A. Provide floor drains in all toilet rooms, janitor closets, and mechanical rooms.
PART 1: GENERAL 1.01 Purpose A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
NUCLEAR POWER CORPORATION OF INDIA LTD TECHNICAL SPECIFICATION ON SUBMERSIBLE PUMPS PAGE NO: 1 OF 4 REV NO : 0 DATA SHEET A
TECHNICAL SPECIFICATION ON SUBMERSIBLE PUMPS PAGE NO: 1 OF 4 DATA SHEET A ANNEXURE - A Sr. Item Description Sr. Item Description A. GENERAL DATA B. PUMP DUTY PARAMETERS 1. System Name 1. Rated capacity,
MATERIAL/MANUFACTURER SPECIFICATIONS FOR DISTRIBUTION WATER MAINS AND APPURTENANCES
MATERIAL/MANUFACTURER SPECIFICATIONS FOR DISTRIBUTION WATER MAINS AND APPURTENANCES REVISION April 2008 1 MATERIAL SPECIFICATIONS T.S. 1 GENERAL Materials incorporated in the finished work and used during
DIVISION 5 METALS COLD FORMED METAL FRAMING Structural Metal Stud Framing
05 40 00 COLD FORMED METAL FRAMING 05 41 00 Structural Metal Stud Framing 05 50 00 METAL FABRICATIONS 05 51 00 Metal Stairs 05 51 13 Metal Pan Stairs 05 52 00 Metal Railings 05 52 13 Pipe and Tube Railings
D. Encase exterior cleanouts in concrete with access cover installed flush with grade.
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
PART 2 SECTION 9 WATERLINES
PART 2 SECTION 9 WATERLINES 9-1 General - All pipe, pipeline installations and facilities related thereto, shall be as specified herein. All pipe installation shall be in accordance with the manufacturers
Request for Bids Water Department. City of Portsmouth, New Hampshire Water Inventory Bid #33-08
Request for Bids Water Department City of Portsmouth, New Hampshire Water Inventory Bid #33-08 1 Bid #33-08 Portsmouth, New Hampshire Public Works Department Water Inventory INVITATION TO BID Sealed bid
Community Services Dept., City of Mississauga Subdivision Requirements Manual Page 1 of 5 Specifications Revised: September 26, 2005
Subdivision Requirements Manual Page 1 of 5 PART I - GENERAL 1.1 Related Work.1 Rough Grading: Section 02211 1.2 Scope of Work.1 This section includes the supply and installation of all labour and materials
CALAVERAS COUNTY WATER DISTRICT Ebbetts Pass Water System Reach 3A Pipeline Replacement Project CCWD CIP No ADDENDUM 2
CALAVERAS COUNTY WATER DISTRICT Ebbetts Pass Water System Reach 3A Pipeline Replacement Project CCWD CIP No. 11078 ADDENDUM 2 Date Issued: December 2, 2015 **** Receipt of addenda must be acknowledged
Exhibit A FOX CHAPEL AUTHORITY STANDARD SPECIFICATIONS FOR MATERIALS AND INSTALLATION OF WATER MAINS
Exhibit A FOX CHAPEL AUTHORITY STANDARD SPECIFICATIONS FOR MATERIALS AND INSTALLATION OF WATER MAINS Requests for extensions to Authority water mains shall be made in writing by the owner or owners of
A. Provide floor drains in all restrooms placed a minimum of 7 from back of wet wall, janitor closets, and mechanical rooms.
SECTION 22 13 00 FACILITY SANITARY SEWERAGE PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
SECTION FACILITY LIGHTNING PROTECTION
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 41 00 FACILITY LIGHTNING PROTECTION SPEC WRITER NOTE: Delete between //----//if not applicable to project. Also delete any other item or paragraph not applicable
8000 PIVOT EXPORT 6-5/8" PIPE 90" COUPLER SPACING
8000 PIVOT EXPORT 6-5/8" PIPE 90" COUPLER SPACING PICTURE Copyright 2009 Valmont Industries, Inc. 8PSP0097 09-97 6-5/8" Export Pipe - 90" Spacing Truss Package Locations 09-0 35' Span 3 5 3 57.5' Span
Volume-II CENTER OF INNOVATIVE & APPLIED BIOPROCESSING DEPARTMENT OF BIOTECHNOLOGY (Govt. of India) Knowledge City, Sector 81, Mohali
Volume-II CENTER OF INNOVATIVE & APPLIED BIOPROCESSING DEPARTMENT OF BIOTECHNOLOGY (Govt. of India) Knowledge City, Sector 81, Mohali FINANCIAL BID DOCUMENT Miscellaneous Civil Work in Low Lying Area at
SECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 23 21 13 HYDRONIC PIPING A. ASME BPVC Section IX - Welding and Brazing Qualifications B. ASME B16.3 - Malleable Iron Threaded Fittings Classes 150 and 300 C. ASME
PND Training Hall Conex Building, Kabul ABSTRACT OF COST
PND Training Hall Conex Building, Kabul ABSTRACT OF COST A Civil Works All work items shall be carried as per drawing, specification and instruction of the Engineer. 1 Sub-structure Works Earthwork in
Electrical Services Standard Specification Cable Tray Installation. May For ROYAL HOLLOWAY UNIVERSITY OF LONDON
Electrical Services Standard Specification 4.0 - Cable Tray Installation May 2010 For ROYAL HOLLOWAY UNIVERSITY OF LONDON Prepared For The Estates Division By: Hulley & Kirkwood Consulting Engineers Ltd
Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations
Issued: Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations Introduction Proper installation and anchorage of Flygt pumps and installation accessories is critical to limiting vibration
SECTION STANDPIPE AND HOSE SYSTEMS
SECTION 15375 STANDPIPE AND HOSE SYSTEMS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: A complete fire protection standpipe system including necessary accessories as indicated on Construction Documents,
SECTION HANGERS AND SUPPORTS PART 1 - GENERAL. A. Drawings and Division 1 Specification Sections, apply to this Section.
1.01 RELATED DOCUMENTS SECTION 15060 HANGERS AND SUPPORTS PART 1 - GENERAL A. Drawings and Division 1 Specification Sections, apply to this Section. 1.02 SUMMARY A. This Section includes hangers and supports
SECTION INSTALLATION OF OWNER-FURNISHED PRODUCTS
SECTION 13 00 50 INSTALLATION OF PART 1 GENERAL 1.1 GENERAL A. Furnish and install all tools, supplies, materials, equipment, appurtenances, and labor necessary for the installation, testing, and placing
SECTION DRAINAGE AND VENT SYSTEMS CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 The design guidelines contained herein include the requirements for drainage and vent systems utilized at The University of Texas at Austin. It is the intention of this document to
SECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 29 HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes pipe and equipment supports, hangers, anchors, bases sleeves and the sealing of work
BILL OF QUANTITIES (BOQ) ADMIN OFFICE - FIRST FLOOR - KALABURAGI
Item No. Civil Works:- BILL OF QUANTITIES (BOQ) ADMIN OFFICE - FIRST FLOOR - KALABURAGI Description Qty. Unit Rate Amount 1 Granite Cladding near entrance. Providing and fixing to the 110 wall after preparing
SECTION (15150) - SANITARY WASTE AND VENT PIPING
SECTION 22 13 16 (15150) - SANITARY WASTE AND VENT PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Pipe Materials. 2. Fittings. 3. Joining Materials. B. Related Sections: 1.02 REFERENCES 1.
A Glossary of Concrete Pumping Terms
Camf audconcr et epumpslt d High Road, Thornwood Common, Epping, Essex, CM16 6LU Tel: 01992 560898 Fax: 01992 573367 www.camfaud.co.uk A Glossary of Concrete Pumping Terms agitator A remixer in the hopper
The Manitoba Water Services Board SECTION Standard Construction Specifications September 2013 Page 1 of 7
September 2013 Page 1 of 7 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work described herein shall consist of the construction of a wetwell as shown on the Plans and in accordance with Section 01001,
PLUMBING PIPE AND PIPE FITTINGS SECTION Sanitary drainage and vent system piping. C. Section 15200: Noise, Vibration and Seismic Control
PLUMBING PIPE AND PIPE FITTINGS SECTION 15065 PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. Work included in this Section: Materials, equipment, fabrication, installation and tests in conformity with applicable