* * * * (317) N

Transcription

1 Protect-Air When SAFETY matters most! Lifesaving products for compressed air. a brand of tri-matic ToolReg * CartReg * FluidReg * HoseGuard * SaveAir (317) N 600 West McCordsville, Indiana

2 Protect-Air Quick product overview a brand of tri-matic Page 3 Page 5 Page 6 Page 7 Page 8 Page 9 Don t take risks! Worth Knowing! Key to Symbols In-line Philosophy and Overview Installation HoseGuard Airfuse Pre-set regulators: Page 14 SaveAir Page 18 ToolReg Page 23 CartReg Page 27 FluidReg Page 31 EcoReg

3 Don t take risks! Act now! Facts and Figures: Globally* 1 Million Registered fatal working accidents 250 Million Registered workplace accidents globally* 12.4 Work days per employee lost due to injury approx Total: Million approx 53 Billion Production Stop costs approx 73 Billion Gross Value Loss First Aid and Prevention Costs 1.16 Billion approx 10 % relate to compressed air a brand of tri-matic The Protect-Air products in this brochure enable managers to comply easily and cost effectively with increasingly stringent guidelines on the safe usage of pneumatic equipment from industry associations such as ISO, OSHA, RoHS, Machine Directive, H&Setc. 3

4 Don t take risks! Ignorance of the law is no excuse! a brand of tri-matic Safety Regulations ISO Standard ISO states: "When failure of a hose assembly or plastic piping constitutes whiplash hazard, it shall be restrained or shielded by suitable means and/or an air fuse for Compressed air shall be mounted. OSHA Regulations Standard 29 CFR, (partial) states(b)(7): All hoses exceeding ½ inside diameter shall have a safety device at the source of supply or branch line to reduce pressure in case of hose failure. Standard 29 CFR, (b)(3): All pneumatically driven equipment provided with automatic fastener feed, which operate at more than 100 psi. pressure at the tool shall have a safety device on the muzzle to prevent the tool from ejecting fasteners, unless the muzzle is in contact with the work surface. 4

5 Worth Knowing! Calculating the return! a brand of tri-matic The ideal pressure for pneumatic tools is generally 6.3 bar (90psig) Every bar (15 psig) of excess pressure essentially wastes 10% of the energy For safety reasons, pneumatic guns should not be operated at pressures exceeding 2 bar (30psig) The expense for energy amounts to % of the cost required to produce compressed air Around 10 KW of electrical energy is required to generate 1 KW of mechanical energy from compressed air Use of pre-set regulators is an economical way to maintain ideal working pressure in the tool 5

6 Key to Symbols a brand of tri-matic The Protect-Air products help plant managers to easily and cost effectively comply with increasingly stringent directives on the safe usage of pneumatic equipment issued by industrial standards organizations such as the ISO, OSHA, H&S (Health & Safety) and others. Safety General safety symbols. Placed on the first page of the appropriate product range, this draws attention to the safety features. Injury Protection The risk of personal injury is reduced by the usage of special materials and technical safety features of the products. The following symbols indicate the safety device or protection products required to conform with regulations. Every product listed complies with one or more safety requirements, laws or regulations. The round symbols indicate the primary type of protection offered by the appropriate product. Compressed Air This symbol always appears on the Laws and Regulations pages and highlights the importance and significance of the laws. Eye Protection The risk of eye injury is reduced by use of special materials and technical safety features of the products. Line Burst Protection Use of line burst protectors prevents the feared whipping effect and helps prevent injuries. Setting Locker These products prevent intentional and unintentional changes in settings, since they include a setting lock. 6

7 In-line Philosophy and overview a brand of tri-matic With Protect-Air s In-line series, use of compressed air becomes simpler, more effective and more economical. The Inline series enables the user to supply any compressed air tool with the ideal air pressure in terms of both purity and quality to provide optimal performance, energy efficiency and economy. The series is directly installed in the piping systems, pressure hoses or tools at the user s installation. In-line regulator SaveAir FluidReg EcoReg - made of EcoBrass /Cuphin Type of Regulator Diaphragm regulator Diaphragm regulator Diaphragm regulator Application Field Mode of Operation Compressed air systems and hoses Reduces air consumption and thus energy costs Various Fluids: Water, compressed air systems, other fluids. Also available for oxygen, nitrogen, etc. Reduces air respectively, water consumption, thus energy Conforms to the DIN /FDA/EU Drinking Water Directive, food industry, medical industry, etc. Reduces air respectively, water consumption, thus energy Tamperproof Yes Yes Yes Comparably high pressure Comparably high pressure Comparably high pressure Pressure Accuracy accuracy accuracy accuracy Automatic pressure Relief Installation Location No No No Do not install between valve and cylinder. Not suitable for pneumatic guns Do not install between valve and cylinder. Not suitable for pneumatic guns Do not install between valve and cylinder. Not suitable for pneumatic guns In-line regulator ToolReg CartReg Type of Regulator Piston regulator Piston regulator Application Field Compressed air tools, especially Compressed air tools, especially nail-guns, tackers, etc. air blow guns Protection against accidents: no Reduces air consumption and Mode of Operation residual pressure remains in the thus energy costs: prevents tool pressure surges Tamperproof Yes Yes Automatic pressure Relief Yes No Installation Location Suitable for use with valves and Directly attached to tool cylinders 7

8 Protection of personnel, machinery and equipment. 8

9 HoseGuard Airfuse-protection of personnel, machinery and equipment. The HoseGuard offers simple but efficient protection to pneumatic systems in the event of a broken compressed air hose or pipe. The air supply is immediately shut of by the HoseGuard, should the volume of air exceed a set value. This value is factory preset and is set to allow normal air consumption when using air tools. Should the air consumption exceed the set value, e.g. the air line is severed, then the internal piston instantly shuts off the main flow. An integral bleed hole allows some air to flow though. This enables the line pressure to automatically reset the HoseGuard once the main break is repaired. 9

10 HoseGuard Airfuse-protection of personnel, machinery and equipment. Advantages: Applications: Protects personnel, machinery and plant Maintenance friendly repair possible while plant is still working Compatible with all pneumatic systems Can be used as a flow blocker Suitable for every application where compressed air is used Compressed air hoses and systems in chemical and pharmaceutical industries Cleanrooms Off - and On-Shore Light weight compact size Tamper proof Complies with OSHA and MSHA regulations 10

11 HoseGuard Technical Data and Ordering Information The HoseGuard offers simple but efficient protection to pneumatic systems in the event of a broken compressed air hose or pipe. The air supply is immediately shut of by the HoseGuard, should the volume of air exceed a set value. This value is factory preset and is set to allow normal air consumption when using air tools. Technical Data Pressure Drop (Open) Pressure Drop (By Closing) Temperature Range 0,05 0,1 bar 0,7 1,5 psig 0,3 bar (4 psig) 1/4, 3/8, 1/2 : -20 C to 80 C (-4 F to 176 F) 3/4, 1 : -20 C to 120 C (-4 F to 248 F) Materials P1 Inlet Thread Housing: Aluminum Stainless Steel Nitrile Rubber Plastic Female/Female Male/Female 11

12 HoseGuard a brand of tri-matic Technical Data and Ordering Information HoseGuard Air Fuse Recommended Maximum Length of Air Hoses (*) at 100 psi Pressure Air Hose Inside Diameter in Inches HoseGuard Air Fuse Thread Dimension Recommended Maximum Length of an Air Hose in Feet 1/4 32 5/16 3/8" 36 7/16 3/8" 65 7/16 1/2" 32 1/2 1/2" 49 5/8 1/2" 82 3/4 3/4" /4" " 98 1 ¼ 1" " ½ 2" 328 (*) Lab-Tests reference values. 12

13 HoseGuard Technical Data and Ordering Information NPT: Thread Connection Description Maximum Inlet Pressure Closing Point Order Code HoseGuard FEMALE/FEMALE NPT 3/8" 1/2" 3/4" 1" HoseGuard Airfuse Standard Standard Standard Standard 18 bar, 255 psig 18 bar, 255 psig 18 bar, 255 psig 18 bar, 255 psig 35 bar, 500 psig approx. 600 Ltrs./Min (21 scfm/min) approx Ltrs./Min (35,3 scfm/min) approx Ltrs./Min (88,3 scfm/min) approx Ltrs./Min (134,3 scfm/min) approx Ltrs./Min (424 scfm/min) PHG281A1211 PHG281A1311 PHG281A1411 PHG281A1511 PHG281A1611 2" 35 bar, 500 psig approx Ltrs./Min (424 scfm/min) PHG281A1911 Thread Connection Description Maximum Inlet Pressure Closing Point Order Code HoseGuard MALE/FEMALE NPT 3/8" 1/2" HoseGuard Airfuse Standard Standard Standard 18 bar, 255 psig 18 bar, 255 psig 18 bar, 255 psig approx. 600 Ltrs./Min (21 scfm/min) approx Ltrs./Min (35,3 scfm/min) approx Ltrs./Min (88,3 scfm/min) PHG281A1221 PHG281A1321 PHG281A1421 *Stainless Steel available upon request. 13

14 SaveAir In-line pre-set energy-saving miniature regulator. The SaveAir regulator is an independent membrane regulator that can be installed in every compressed air system. It supplies a constant, exact outlet pressure regardless of the input pressure. The pressure is factory-set and cannot be changed. SaveAir prevents dynamic pressure waste. This arises when the pressure and flow at the withdrawal point are unnecessarily higher than those specified by the manufacturer to achieve the desired function. Dynamic pressure waste is extremely costly, a waste of energy that may be found throughout industry. 14

15 SaveAir In-line pre-set energy-saving miniature regulator. Advantages: Applications: Supplies tools exclusively with the specified pressure No pressure gauge needed Prevents compressed air waste Saves energy reduces costs Highly reliable Piping and compressed air systems Compressed air used in automation for actuation Control, feeding or transportation Pick and place units in automatic assembly systems Locked to prevent pressure change tamper proof Small and compact Increases tool service life 15

16 SaveAir Technical Data and Ordering Information The regulator ensures that a constant pressure is always maintained, despite the normal pressure fluctuations in a system. The regulator is intended for use with compressed air or neutral gases. To avoid unnecessary loss of pressure in long pipes or hoses, the regulator has to be mounted as close as possible to the point of consumption. Technical Data Weight Maximum Inlet Pressure Temperature Range Material P1 Inlet Thread 82 g 18 bar/255psig 0 C to 60 C (32 F to 140 F) Housing: Zinc Diaphragm: CR Spindle: Brass Spring: Stainless Steel O-Ring: Nitrile Rubber Female/Female 16

17 SaveAir a brand of tri-matic Technical Data and Ordering Information NPT: Thread Connection Description Flow P2 outlet preset pressure Order Code SaveAir - In-line preset regulator NPT SaveAir In-line preset regulator SaveAir NPT, 15 psig SaveAir NPT, 30 psig SaveAir NPT, 45 psig SaveAir NPT, 60 psig SaveAir NPT, 75 psig SaveAir NPT, 90 psig SaveAir NPT, 100 psig SaveAir NPT, 120 psig FEMALE/FEMALE 400 Ltrs./Min scfm 15 psig PIR231AS Ltrs./Min scfm 30 psig PIR231AS Ltrs./Min scfm 45 psig PIR231AS Ltrs./Min scfm 60 psig PIR231AS Ltrs./Min scfm 75 psig PIR231AS Ltrs./Min scfm 90 psig PIR231AS Ltrs./Min scfm 100 psig PIR231AS Ltrs./Min scfm 120 psig PIR231AS12120 *Tolerances Test medium: Air, Pe = 6 bar/90 psig (at Pa <= 4 bar/60 psig), 10 NI/Min / 0,35 scfm Test medium: Air, Pe = 10 bar/150 psig (at Pa <= 4 bar/60 psig), 10 NI/Min / 0,35 scfm 17

18 ToolReg In-line pre-set regulator with automatic secondary pressure relief. The ToolReg regulator is an independent piston regulator that can be mounted on any pneumatic tool or installed in every compressed air system. It supplies a constant, exact outlet pressure regardless of the inlet pressure. The pressure is factoryset and cannot be changed. The ToolReg prevents dynamic pressure waste. This arises when the pressure and flow at the withdrawal point are unnecessarily higher than those specified by the manufacturer to achieve the desired function. Dynamic pressure waste is extremely costly, and a waste of energy that may be found throughout industry. For pneumatic tools the ToolReg must be mounted directly on the tool in order to ensure correct pressure, so that possible pressure drops in hoses, tubes etc. do not influence the pressure on the tool itself. Furthermore, the residual pressure in the tool is relieved when it is removed from the compressed air supply line, preventing unintentional actuation of the tool with disastrous consequences. 18

19 Advantages: ToolReg In-line pre-set regulator with automatic secondary pressure relief. Applications: Automatic secondary pressure relief Protection guaranteed no residual pressure in the tool High flow performance ( Ltrs./Min / scfm) High pressure performance (P1 inlet pressure up to 25 bar / 355 psig) Saves energy reduces costs Pneumatic tools Furniture, construction and precision engineering trades Compressed air used in automation for actuation Control, feeding, or transportation Pick and place units in automatic assembly systems Tamper proof Increases tool service life 19

20 ToolReg Technical Data and Ordering Information The Toolreg regulator ensures that a constant pressure is always maintained, despite the normal pressure fluctuations in a system. The regulator is intended for use with compressed air or neutral gases. The Toolreg must be mounted directly on the pneumatic tool in order to ensure correct pressure, so that possible pressure drop in hoses, tubes, etc. do not influence the pressure on the tool itself. Furthermore, the residual pressure in the tool is relieved when it is removed from the compressed air supply line, preventing unintentional actuation of the tool with disastrous consequences. Technical data Weight 1/4 F/F 30 g F/M 40 g Weight 3/8 F/F 48 g Weight 1/2 F/F 100 g Maximum Inlet Pressure 25 bar/365psig Temperature range 0 C to 80 C(32 F to 176 F) Material Aluminum Stainless Steel Nitrile Rubber, Brass, PPH 20

21 ToolReg Technical Data and Ordering Information Thread Connection Description Flow at 90 psig Tolerances Order Code ToolReg - In-Line preset TOOLREG FEMALE/FEMALE NPT ToolReg In-line pre-set ToolReg NPT 2 bar / 30 psig ToolReg NPT 3 bar / 45 psig ToolReg NPT 4 bar / 60 psig ToolReg NPT 5 bar / 75 psig ToolReg NPT 6 bar / 90 psig ToolReg NPT 7 bar / 105 psig ToolReg NPT 8 bar / 120 psig Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm ± 4 psig PTR232AS1230 ± 4 psig PTR232AS1245 ± 6 psig PTR232AS1260 ± 7.5 psig PTR232AS1275 ± 9 psig PTR232AS1290 ± 10 psig PTR232AS12105 ± 12 psig PTR232AS12120 Thread Connection Description Flow at 90 psig Tolerances Order Code ToolReg - In-Line preset TOOLREG MALE/FEMALE NPT ToolReg In-line pre-set ToolReg NPT 2 bar / 30 psig ToolReg NPT 3 bar / 45 psig ToolReg NPT 4 bar / 60 psig ToolReg NPT 5 bar / 75 psig ToolReg NPT 6 bar / 90 psig ToolReg NPT 7 bar / 105 psig ToolReg NPT 8 bar / 120 psig Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm Ltrs./Min 0-26,5 scfm ± 4 psig PTR232FS1230 ± 4 psig PTR232FS1245 ± 6 psig PTR232FS1260 ± 7.5 psig PTR232FS1275 ± 9 psig PTR232FS1290 ± 10 psig PTR232FS12105 ± 12 psig PTR232FS

22 ToolReg Technical Data and Ordering Information Thread Connection Description Flow at 90 psi Tolerances Order Code ToolReg - In-Line preset NPT 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" ToolReg In-line preset ToolReg 3/8" NPT 2 bar / 30 psig ToolReg 3/8" NPT 3 bar / 45 psig ToolReg 3/8" NPT 4 bar / 60 psig ToolReg 3/8" NPT 5 bar / 75 psig ToolReg 3/8" NPT 6 bar / 90 psig ToolReg 3/8" NPT 7 bar / 105 psig ToolReg 3/8" NPT 8 bar / 120 psig 3/8" TOOLREG FEMALE/FEMALE Ltrs./Min 0-70 scfm Ltrs./Min 0-70 scfm Ltrs./Min 0-70 scfm Ltrs./Min 0-70 scfm Ltrs./Min 0-70 scfm Ltrs./Min 0-70 scfm Ltrs./Min 0-70 scfm ± 4 psig PTR232AS1330 ± 4.5 psig PTR232AS1345 ± 6 psig PTR232AS1360 ± 7.5 psig PTR232AS1375 ± 9 psig PTR232AS1390 ± 10.5 psig PTR232AS13105 ± 12 psig PTR232AS13120 Thread Connection Description Flow at 90 psi Tolerances Order Code ToolReg - In-Line preset NPT 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" ToolReg In-line preset ToolReg 1/2" NPT 2 bar / 30 psig ToolReg 1/2" NPT 3 bar / 45 psig ToolReg 1/2" NPT 4 bar / 60 psig ToolReg 1/2" NPT 5 bar / 75 psig ToolReg 1/2" NPT 6 bar / 90 psig ToolReg 1/2" NPT 7 bar / 105 psig ToolReg 1/2" NPT 8 bar / 120 psig 1/2" TOOLREG FEMALE/FEMALE Ltrs./Min scfm Ltrs./Min scfm Ltrs./Min scfm Ltrs./Min scfm Ltrs./Min scfm Ltrs./Min scfm Ltrs./Min scfm ± 4 psig PTR232AS1430 ± 4.5 psig PTR232AS1445 ± 6 psig PTR232AS1460 ± 7.5 psig PTR232AS1475 ± 9 psig PTR232AS1490 ± 10.5 psig PTR232AS14105 ± 12 psig PTR232AS

23 CartReg In-line pre-set regulator for air blow guns and pneumatic tools. The CartReg pre-set miniature regulator is installed in the compressed air supply line. It is designed to meet OSHA (Occupational Safety & Health administration, USA) and other safety agency requirements for 2 bar/30psig maximum pressure for pneumatic air guns. The CartReg can easily be threaded into any ¼ air blow gun and pneumatic tool and is an economical means to maintain the ideal pressure requirements. 23

24 CartReg In-line pre-set regulator for air blow guns and pneumatic tools. Advantages: Safety: protects personnel, machinery and plant by avoiding pressure surges Ensures optimal air tool efficiency by supplying a constant pre-set pressure Prevents compressed air waste limits excessive compressed air consumption = reducing energy costs Easy assembly: can be integrated into any ¼ pneumatic tool Lightweight (14 g) and compact (Hexagon 14 mm, length 24 mm) Tamper proof Increases tool service life Applications: Pneumatic air guns Pneumatic tools Pick and place units in automatic assembly systems High-pressure performance (P1= inlet pressure up to 18 bar/260 psig) High flow performance (up to 400 L/Min 15 scfm 24

25 CartReg Technical Data and Ordering Information The regulator ensures that a constant pressure is always maintained, despite the normal pressure fluctuations in a system. The regulator is intended for use with compressed air or neutral gases. The Cartreg must be mounted directly on the pneumatic blow gun or tool in order to ensure correct pressure, so that possible pressure drops in hoses, tubes, etc. do not influence the pressure on the tool itself. Technical data Weight Maximum Inlet Pressure Temperature range Material P1 Inlet Thread 14 g 12 bar/174psig 20 C to 60 C (-4 F to 140 F) Brass, Stainless Steel NBR Male/Male 25

26 CartReg Technical Data and Ordering Information Thread Connection Description Flow Tolerances Order Code CartReg - In-Line pre set miniature regulator NPT CartReg In-line pre-set miniature regulator CartReg NPT 2 bar / 30 psig CartReg NPT 4 bar / 60 psig CartReg NPT 6 bar / 90 psig 14 scfm ± 8.7 psig (Pe 87 psig) PCR233S scfm ± 11.6 psig (Pe 87 psig) PCR233S scfm ± 14.5 psig (Pe 145 psig) PCR233S1290 *Tolerances Test medium: Air, Pe = 6 bar/90 psig ( at Pa <= 4 bar/60 psig), 10 NI/Min / 0,35 scfm Test medium: Air, Pe = 10 bar/150 psig ( at Pa <= 4 bar/60 psig), 10 NI/Min / 0,35 scfm 26

27 FluidReg In-line pre-set regulator for water and other fluids on request. The FluidReg is an independent membrane regulator that can be installed in every fluid or compressed air pneumatic system. It supplies a constant, exact outlet pressure regardless of the input pressure. The pressure is factory-set and cannot be changed. This ensures that nobody can alter the specified pressure. It is well known that the pressure of a water or fluid line normally is too high, fluctuates, and varies according to the height of the building. In that case the In-line FluidReg protects all equipment and components placed after it, because thus they will only receive the correct pressure. This is particularly important for all machinery/ plants for/or with dosing of liquids, as this will prevent stops in production. Furthermore if the FluidReg is combined with a sprinkler nozzle, the best basis for cooling/cleaning by means of water spray or fog is created. 27

28 FluidReg In-line pre-set regulator for water and other fluids on request. Advantages: Applications: Reduces energy consumption Service free: no adjustment needed Easy to mount in any water supply system Extension by sprinkler equipment Highly reliable Coffee and soft drinks machines Filling machines Laboratory dosing equipment Pharmacies Food industry Irrigation systems etc. Locked to prevent pressure change tamper proof Lightweight and compact Increases tool service life 28

29 FluidReg Technical Data and Ordering Information The regulator ensures that a constant pressure is always maintained, despite the normal pressure fluctuations in a system. The regulator is intended for use with various fluids such as drinking water, tap water or with compressed air and also in a special version with oxygen. To avoid unnecessary loss of pressure in long pipes or hoses, the regulator has to be mounted as close as possible to the point of consumption. Technical Data Weight Max. Inlet Pressure Temperature Range Materials P1 Inlet Thread 125 g Water: 10 bar/145 psig other gases: 18 bar/255 psig Water: 4 C to 60 C (39 F to 140 F) Other gases: 0 C to 60 C (32 F to 140 F) Housing: Brass Nickel Plated Spring: Stainless Steel O-Ring: Nitrile Rubber Valve Seat: PPH Spindle: Brass Nickel Plated Female/Female 29

30 FluidReg a brand of tri-matic Technical Data and Ordering Information NPT: Thread Connection Description Flow ml/min ( 12 psig) Tolerances Order Code FluidReg NPT FluidReg SaveAir NPT, 15 psig SaveAir NPT, 30 psig SaveAir NPT, 45 psig SaveAir NPT, 60 psig SaveAir NPT, 75 psig SaveAir NPT, 90 psig SaveAir NPT, 100 psig SaveAir NPT, 120 psig FEMALE/FEMALE ± 2 psig PWR239AS ± 4 psig PWR239AS ± 4.5 psig PWR239AS ± 6 psig PWR239AS ± 7.5 psig PWR239AS ± 9 psig PWR239AS ± 10 psig PWR239AS ± 12 psig PWR239AS12120 *Tolerances Test medium: Air, Pe = 6 bar/90 psig (at Pa <= 4 bar/60 psig), 10 Nl/Min / 0,35 scfm Test medium: Air, Pe = 10 bar/150 psig (at Pa <= 4 bar/60 psig), 10 Nl/Min / 0,35 scfm 30

31 EcoReg In-line pre-set regulator for water and other fluids Available on request for oxygen, nitrogen, etc. Made of the lead-free brass material Ecobrass/ Cuphin ideal for critical application areas such as drinking water, food industry, medical industry, etc. Conforms to the DIN /FDA/EU drinking water directives and other regulations. The use of lead-free materials is growing in importance in particular as an alternative material for drinking water applications, where health standards are high. As an alternative material to conventional brass, Protect-Air offers a fluid regulator made of a lead-free brass material Ecobrass (trade name CUPHIN).* The fluid regulators made of Ecobrass are minimally susceptible to tension-crack corrosion and are dezincification-resistant, which makes an additional surface treatment unnecessary. This is environmentally friendly, saves cycle times, additional procedures and there by costs. These are all good reasons to choose Protect-Air Ecobrass fluid regulators that meet health and safety requirements and in areas that are constantly Subject to corrosion risk. 31

32 EcoReg In-line pre-set regulator for water and other fluids Available on request for oxygen, nitrogen, etc. Advantages: Reduces consumption Reliability Tamper proof Lightweight compact construction Easy to mount in any water supply system Extension by sprinkler equipment In compliance with prevailing Food and Feed Code of Law (TÜV) Increases tool service life 32

33 EcoReg Technical Data and Ordering Information The EcoReg fluid regulator is an independent diaphragm pressure regulator that can be installed in all fluid systems. The pressure regulator ensures a constant and precise output pressure independent from the input pressure. The pressure value has been factory preset and cannot be changed. This ensures that no one can manipulate the specified pressure value. Technical Data Weight Max. Inlet Pressure Temperature Range 125 g Water: 10 bar/145 psig other gases: 18 bar/255 psig Water: 4 C to 60 C (39 F to 140 F) Other gases: 0 C to 60 C (32 F to 140 F) Materials Housing: EcoBrass/Cuphin Spring: Stainless Steel O-Ring: Nitrile Rubber Valve Seat: PPH Spindle: EcoBrass/Cuphin P1 Inlet Thread Female/Female 33

34 EcoReg Technical Data and Ordering Information NPT: Thread Connection Flow ml/min Tolerances P2 outlet preset pressure Order Code EcoReg NPT EcoReg -Clinical application with Viton FEMALE/FEMALE ± 2 psig 15 psig PER239CS ± 4 psig 30 psig PER239CS ± 4.5 psig 45 psig PER239CS ± 6 psig 60 psig PER239CS ± 7.5 psig 75 psig PER239CS ± 9 psig 90 psig PER239CS ± 10 psig 100 psig PER239CS12100 *Tolerances Test medium: Air, Pe = 6 bar/90 psig (at Pa <= 4 bar/60 psig), 10 Nl/Min / 0,35 scfm Test medium: Air, Pe = 10 bar/150 psig (at Pa <= 4 bar/60 psig), 10 Nl/Min / 0,35 scfm 34

35 NOTES: a brand of tri-matic

36 PROTECT-AIR, USA 8250 N. 600 West, McCordsville, Indiana PHONE (317) FAX (317) The Products for a safe working place. 09/19/13 Rev. A